VT advantage not being recognized by windows xp

I have installed VT software version 2.02 and IP communicator. Somehow, windows xp does not recognize hardware installed and in the device manager, USB device is marked not known.
VT advantage software doesnot recognize softphone installed on PC and also hardphone.
Any ideas.

Hi,
I assum you are administrator on the local machine, did you install the software before pluging in the camera, if not, delete the device and remove the software as well as unplug the camera and do the installation again after a reboot.
make sure you have the latest Service pack on XP (i think min should be SP1)
Good day

Similar Messages

  • Ipad is not being recognized by Windows..I get a Code 43 error on any USB port I try. I have rebooted, restarted, blah blah til I am blue in the face.

    Ipad is not being recognized by Windows..I get a Code 43 error on any USB port I try. I have rebooted, restarted, blah blah til I am blue in the face. This is an Ipad not an Ipad2...I can't get this thing recognized by either my desktop or laptop. It used to work...not now.
    Any ideas?

    Did you already have a look at this article?
    iOS: Device recognized in iTunes for Mac OS X

  • TS1567 iPhone not being recognized by Windows 8 or iTunes

    My iPhone is not being recognized by my Windows 8 laptop, or itunes. I have used the original cable and a new one. Both cause the computer to ding when the phone connects, but i cant find the phone ANYWHERE. I have stopped and restarted the Apple Mobile Support Service. And restarted my laptop.

    All needed drivers are installed when you install iTunes and QuickTime. Try to reinstall the Apple software again, as explained in this article:
    Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista,Windows 7 or Windows 8

  • Does anyone have problems with the 7th generation nano not being recognized by windows?

    Just got my nano and although it worked the first time I plugged it in to my laptop, it now can not be recognized by Windows, it is completely dead and will not charge at all...anyone else having this issue?

    Hello Chloe
    Start with the first article below to go over some general hardware troubleshooting to get a charge on your iPod nano. If you get that to turn on and you cannot get it to show up on your computer, then the second article should sort you out.
    iPod nano (7th generation): Hardware troubleshooting
    http://support.apple.com/kb/TS4433
    iPod not appearing in iTunes
    http://support.apple.com/kb/TS3716
    Regards,
    -Norm G.

  • IPod not being "recognized" by Windows XP

    So I just got my 30GB iPod Video and I installed all the software and stuff. I hooked the USB cable up, but each time windows says "USB Device not Recognized". I looked at the message and it says something about a driver not being installed for the device. If anyone could help me I would love it!!! I've done EVERYTHING!!!

    I hope this will help. I had installed my 5th Gen. 30 Gig iPod on my computer which originally only had 1.1 USB ports on it at that time, and it did sync and work, but I wanted to be able to sync faster. So, I had a 2.0 USB card installed. This card would not recognize my iPod at all. I reinstalled iTunes and iPod software thinking that would help, but nothing helped the 2.0 card simply would not work with the iPod.
    So, I went to the iPod search site and did a search to find approved 2.0 usb cards. That yeilded several pages of approved USB cards. I took this list to my computer guru, they ordered me one of the approved cards, took out the first "generic usb 2.0" card they had installed and put in the new on. Guess what, it immediately worked when I plugged in my iPod!!! It copied 59.2 minutes worth of music to the iPod in less than 10 seconds! I am amazed how much faster it is.
    I say all of this to say that your computer's USB card may not be compatible with your iPod. If not, change out the card with one that is. I hope you will have the same success I had. What a difference it makes! Good luck.
    Dell Dimension 4300   Windows XP   5th Generation 30gig iPod

  • IPod Classic 5th Gen (30 GB) not being recognized by Windows 7 Vista Netbook.

    My iPod isn't being recognized I tried everything . Reinstalling Itunes. Resetting Ipod. Putting it in Disk mode. everything. I plugged it up to my school's mac desktop and it syncs and everything. On my Windows it doesn't even show up as mass storage device or anything. It's annoying. I just want to listen to music.
    Is there a driver or something?
    My friend said Registry fix, but i doubt it.
    When I try to update driver, it says the most recent one has been updated.
    This *****.
    Please help

    When you plug in the iPod does it even appear in Device Manager?  See this article for more details.
    http://support.apple.com/kb/TS1496
    Otherwise, I have a feeling that the USB ports on the Netbook don't output enough power to allow the iPod to fully communiate properly with the Windows Vista O/S.
    B-rock

  • IPod Touch not being recognized by Windows 7.

    So I have a little problem, my USB cable will charge if I use the wall charger but when I try to connect it to my PC it doesn't.I can't seem to make it appear on iTunes either.Tried using the troubleshooter with no succes tough,

    See:
    iOS: Device not recognized in iTunes for Windows
    I would start with
    Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
    Run this to help if it identifies the cause
    iTunes for Windows: Device Sync Tests
    Have you tried on another computer to help determine if you have a computer or iPod problem?

  • IPod Touch 4G 8GB charging perfectly, but not being recognized by Windows 7 OR iTunes?

    Ipod touch charging, but not recognized by Itune or windowes, other divises are ( Iphone4 , Ipad) only my itouch is not... Should I reset it ?

    Hi lllaass,
    This looks like a very common problem.
    I tried everything. Reset, Safe Mode, checked all cable, Apple Services from the dminstration tools.... other devises, like my Iphone and Ipad works perfectly.Only this itouch doesn't. If I reset all I will loss all my data since I can't back it up. It's jailbroken and it was wotking fine. Could it be software that I downloaded recently?I'm not sure it will work even if reset all.  THANKS FOR YOUR HELP.

  • Ipod not being recognized by windows computer

    I have a video Ipod and a older nonclick wheel type Ipod. Neither one will connect to my computer. Although last week they connected without any problem. Also my wife's Ipod mini connects correctly. I've uninstalled Itunes and reinstalled it. I reinstalled the drivers for the 'Mass storage usb device' in the device manager. I've reset my Ipods.What should I do next?

    Have you had a chance to look at these troubleshooting pages? They may be of some help:
    iPod missing in My Computer and in iTunes
    iPod is not recognized properly by computer when USB drivers are not installed properly or are out of date
    Microsoft Support - A computer that is running Windows XP cannot detect a USB thumb drive, an Apple iPod, or an external hard disk drive
    If you are using a laptop, this page might help: iPod not recognized when connected to Windows laptop over USB

  • 5th Gen 80GB is not being recognized by Windows/iTunes

    Alright guys, here's my situation. My iPod has always worked fine. Today I plugged it in like I do every other day. When I plugged it in iTunes did not recognize it and then I got a Windows message that said "One of the USB devices attached to this computer has malfunctioned and Windows cannot recognize it." I thought this was strange because NOTHING about my iPod/iTunes had changed whatsoever. Next, I was prompted to update to the latest version of iTunes so I thought, "Oh dummy, that was the problem, you had an old version of iTunes." Wrong. I updated iTunes and STILL no recognizing of my black beauty. Next I turned to the Apple website to see what it said. I tried all of the options except "restore" because I refuse to lose my collection on my iPod. I have also tried using a different USB port, but that wasn't the problem. Reminder: the iPod is not recognized under the Device manager. So now I turn to my brothers here to help me solve my problem.

    Try a different cable and if that fails, see if it is recognised in another computer, if youre ipod is still within warranty send it back to apple, it may be the dock connector.
    Good luck and welcome to the boards
    Joe

  • My ipod is not being recognized by Windows XP. Any Solutions for this problem?

    When I plug in my ipod to my ASUS Netbook it says, "Usb Device Not Recognized". When I tried a different device it vworked fine, so is there a problem with the ipod itself?

    What were the other devices? If not an iPod touch, iPhone or iPad then try:
    iOS: Device not recognized in iTunes for Windows
    If one was one of those devices then time for an appointment at the Genius Bar of an Apple store.

  • My i pod touch is not being recognized by windows 7, I have done all the suggestions through apple website, and still the problem persists.

    I have done everything that Apple Support has suggested, What can I do to fix this issue without having to replace the ipod?

    I am afraid that the solution did not work... the ipod touch of mine seems really not functioning. It receives an electric isgnal from the computer but it doesnt sync at all... Whenever I put my ipod touch off and plug it to my computer it turns on but it doesnt sync... .. Moreover, I have used different PCs so as to try it syncing.. I have used mac book pro and windows 7 laptops but it gives similar feedback, which is NO FEEDBACK at all...

  • MOTU 828 mk ll not being recognized by Windows XP in Bootcamp

    Hi All,
    I have been pulling my hair out over this - and believe me I don't have much to spare! I cannot seem to get Windows to see my MOTU 828 mk ll audio interface.
    I have Boot Camp installed with Windows XP service pack 2, updated to service pack 3. I ran the snow leopard driver installers again after I did the service pack 3 upgrade. I've installed and uninstalled the MOTU firewire/USB driver package over and over again, and rebooted ad nauseum, all without success.
    I then tried upgrading the firewire drivers to the AVT FirePackage, thinking they might be more robust than Microsoft's. Reinstalled the MOTY drivers, etc - no change. Needless to say, the 828 mk ll runs perfectly under OS X, so I know there's nothing wrong with the unit, cables, or FW port on my tower.
    Any ideas or insights would be greatly appreciated.
    Eli

    Hi Eli,
    i´m actually facing the same problems using a traveler, no problems on OS 10.6 no detection on WIN XP.
    I contacted Motu Tech links and Matthew a service technican wrote me that,
    Hi Michael,
    There is a setting in the Windows registry that controls the data rate between the FireWire adapter and connected devices. Adjusting this setting might resolve the problem you're experiencing. Please follow these steps to adjust this value in the Windows registry. Make sure to power off your Traveler before hand.
    1. In the Start menu, choose Control Panel > System > Hardware. Click the Device Manager button.
    2. In the Device Manager, expand the section titled IEEE 1394 Bus Host Controllers. Right-click on the FireWire adapter device to which the audio interface is connected, and choose Properties.
    3. In the Properties window, select the Details tab. In the Property dropdown menu, select Device Instance ID.
    4. In the Value field, you will see a string of letters and numbers that is similar to the following:
    PCI\VEN104C&DEV_8020&SUBSYS_00D81028&REV00\4&19FD8D60&0&60F0
    The second and third parts of this string are significant. The portion of the string between the two backslashes (\) is the hardware ID for the FireWire adapter. The portion of the string following the final backslash is the instance ID. Keep the Properties window open or save these values.
    5. In the Start menu, choose Run. Type regedit at the command prompt. Press return to launch the Registry Editor.
    6. In the Registry Editor, navigate to this registry subkey using the folder hierarchy at the left side of the window:
    HKEYLOCAL_MACHINESYSTEMCurrentControlSetEnumPCIhardware_IDinstanceID
    The hardware_ID and instance_ID are the values from step 4 (Device Manager > FireWire adapter properties > Details > Device Instance ID).
    7. When you have reached this subkey, select Device Parameters. In the right side of the window, you may see one or more defined values. If you see a value named SidSpeed, continue to step 8. If the SidSpeed value does not exist in the right pane after you click the Device Parameters subkey, you will need to create it. To do this, open the Edit menu and choose New > DWORD Value. Type SidSpeed for the value's name, and then press return.
    8. Right-click on SidSpeed, and select Modify. In the value data field, enter 3, and then click OK.
    9. Close the Registry Editor program, and then restart the computer. After the computer has restarted, log in to Windows and test the problem again.
    Hope this will do,
    greetings, Michael

  • Ipod touch not being recognized by Windows

    First of all sorry if my english will not be good enough, I'm italian :P
    Well, yesterday I updated my itunes to 9.0 version and i tried to sinch my ipod touch..
    When I put my ipod touch into the USB door it gives me this error: He says that the APPLE MOBILE DEVICE USB DRIVER is missing..
    I tried everything, from uninstalling Itunes to updating this driver, but it's still not working..
    What should i do??
    Thanks for your support

    So, it still doesn't work..
    I uninstalled Itunes, QUicktime and AMDS, tried to reinstall'em but it's not working
    I tried to connect the ipod to several USB doors, but it gives me the same problem.
    Also i tried to open Itunes and now it says "Itunes couldn't connect to this Iphone because of an unknown error (0xE800006B)"

  • My ipod is not getting charged, and its not being recognized by windows

    The day before, i left my ipod in the bathroom for the whole day without doing anything to it. Yes, the battery was already drained i just didn't charge it.
    Today, I connected my ipod to my computer to charge but nothign is happening. Usually it'll say say something like "please wait very low battery", but as of now its completely blank. I did the basic troubleshooting procedures, reseting, restarting pc, updating... etc. I also tried to connect to a different computer but it still doesnt' work. I always leave the cable connected to the pc sitting on my desk and i'm positive nothign happenend to it, unless it broke while sitting on a table. I've had this ipod for bout 8 months now and this has never happened.
    Is there anything else i can do to fix this before sending it to apple?
    Thanks

    1. Battery life IS directly related to quantity of charge cycles.
    2. I never heard the "400" figure. Where did you get it from?
    3. Even if "400" is correct, the battery could have been defective from the start and perhaps this one can take only 100 charge cycles. For what it's worth, it does seem like it died too soon. From what I've seen here on the forums, batteries typically ast 18 to 24 months, obviously dependent on usage.
    4. I could be totally wrong about the battery being shot! I just can't imagine what else it could be.
    All the above notwithstanding...
    I don't think that the magnet storage is a good idea but I don't think that it would cause this problem. Unfortunately, the bottom line is that you can't do any testing or try any of the basic repair sequences if you can't charge the iPod. If you're close to an Apple Store (owned and operated by Apple), take it to the "Genius Guy" or whatever he's really called. You will need an appointment. Don't tell Apple about the magnets!

Maybe you are looking for