VU levels not matching going from Audition to PPro

Couldn't find this in a search, excuse if this has been discussed.
I mixed a multi-track sequence arriving from PPro in Audition with a compressor on each vocal channel, and the VU meters were peaking nicely around -6db.  When I export back to my PPro sequence, everything is peaking at -12db or so.  Am I missing something?  Do I just raise the levels once I get back to PPro, or would that give me less-than-optimal audio to boost it there?
Any input would be greatly appreciated for this workflow! (For a brand new Audition user...)

Audition's mixer does a -3 dB compensation when things are panned center to better mimic stereo pan pots on hardware consoles.  More info: http://blogs.adobe.com/insidesound/2010/10/following-the-letter-of-the-pan-law.html
To disable this, just change the Panning Mode preference to "Left/Righ Cut (Logarithmic)" shown here:

Similar Messages

  • Adobe Audition Volume Levels Not Matching

    Hello everyone. I have a quick question and have been looking the answer for quite a while. I seem to not be able to find it thought.
    Every time I export let's say a multi track mix down from audition, the volume seems to be lower than the original track. Mind you I have not compressed to a lower format, I always keep everything same as source (which in my case is 48000 Hz, 32-bit, 320kbps CBR) (sometimes I force the entire project to conform to the settings mentioned above by manually choosing them in the export dialog). However, if I play the mix down version of the exported song next to the actual song itself, the original always sounds much louder than my exported file. why is this? This is very frustrating as I feel my mixes aren't coming out to their full quality potential. There is always degradation in volume. I always make sure that my master volume is set to 0db so that it isn't louder or quieter than the original. I have to up the damn master for the entire mix in order for it to sound as loud as the original. I don't want this thought because it messes with my audio levels for some/most of the transitions.
    Should I be exporting the mix down as an uncompressed wav, then compressing to mp3 using a different software?
    Any insight would be greatly appreciated. And apologies for the noob question.
    Thank you

    By default, there is a –3dB drop in amplitude when mixing in Multitrack View.  You can change this behavior permanently under Preferences > Multitrack > Default Panning Mode  by choosing Left/Right Cut (logarithmic)
    This is based on the concept of Pan Law (http://en.wikipedia.org/wiki/Pan_law) which prevents unintentionally loud volume increases when a signal is panned in the center of a stereo field.  The Wikipedia link goes into much more detail.

  • Audio from Sony EX1r Camera will not round trip from Audition

    With Premier CC15 the audio from my Sony EX1R Video Camera comes back from Audition after the edit  just as a loud buzz.  It works fine in Premier 6 and also CC.  My Panasonic camera Audio, as well as all others work fine. 
    Can someone help?

    Giving up? Four product releases in nine months. That's a pretty aggressive development schedule for a new product.
    Motion is a separate development track and always has been. Roundtripping to Motion was not available in its first releases. Apple has taken a new approach with publishing and rigging, which has great benefits. It basically meant that the entire effects, transitions, generators, and titling architecture didn't have to be rebuilt in FCP and that the two applications can work together. There are a lot of things this allows. For instance, if you want to add effects from Motion to clips in FCP, roundtripping is quite unnecessary; simply publish the effect with the parameters you need and apply the effect inside FCP.
    Roundtripping is really useful for a lot of things and will probably be implemented. In the interim third party soluations using XML hooks are available.

  • Cross Tab Report not matching Data from report

    I created a report showing the number of orders created by each department per year for the last 5 years.  I double checked the data, and 2005, 2006, 2007, 2008, and 2009 all are correct. 
    I then created a cross-tab for quick reference for my department head.  2005, 2006, 2007, and 2009 are all correct.  2008 is not. It shows 500 more orders than the data in the report for that year.
    I double checked my  "Group options" to make sure that they were the same in both the data and in the crosstabs.  Any idea what I could be missing?
    Thank you.

    Try this, limit the report to only 2008, show details, add date to detail section, and add the record number (From special fields)
    see if this count matches what you think it should be, or is 500 over like the crosstab indicates.  You could group by date, by month, add a summary (Count) by date, and see what that comes up to.  If your extra records fall in a certain date range, double check the database to make sure there are not duplicate records.

  • What happened to my "notes" after going from SL to ML?

    Upgraded to Mountain Lion direct from Snow Leopard, and notes were part of mail.app before. Just noticed that my notes do not show up in notes.app
    Where would I find them....?

    Hi peda74,
    Welcome to the Support Communities!
    The article below may be able to help you with this.
    Click on the link to see more details and screenshots. 
    iOS: Syncing Notes
    http://support.apple.com/kb/HT4191?viewlocale=en_US
    Notes are associated with an IMAP email account or iCloud account. To sync Notes, enable Notes for each account in Settings > Mail, Contacts, Calendarsor Settings > iCloud.
    If notes are not syncing as expected, check the following:
    Ensure that you enabled Notes for that account in Settings > Mail, Contacts, Calendars or Settings > iCloud.
    In Notes on your iOS device or Mac, verify that your notes are not stored in a local folder. Example: On My iPhone or On My Mac. If you have notes in these folders, you will need to copy or transfer them to iCloud or IMAP to sync with your other devices.
    Cheers,
    - Judy

  • Border levels not matching between columns

    Hi!
    Ihave a little problem within one of my reports as the border hights doesnt match between two columns, see  under Affordable and Core in the picture below.
    Anybody that has a solution to this problem?
    Br Arne
    Arne Olsson

    Hi Arne,
    Based on your description, could you tell me the columns are in a same tablix or in two tablix? Do you set the border color of the tablix cells? Could you share the expression that you use to set the border color? If possible, could you please post the screenshot
    about your report design? This will be helpful for us to reproduce the issue and help you to resolve it.
    Thank you for your understanding.
    Regards,
    Katherine Xiong
    Katherine Xiong
    TechNet Community Support

  • Dynamic Table Sorting not working going from MX to 8

    I have a table with a repeat region and had buttons to sort
    any of the columns on the page.. This was working in Dreamweaver MX
    but since upgrading to 8 it doesn't.
    The way I did it in MX was to create two variables:
    varName - DateSubmitted (default value which is db field
    name) - Request.QueryString("order") (runtime value)
    varSort - ASC (default value) - Request.QueryString("sort")
    (runtime value)
    And my SQL statement:
    SELECT *
    FROM TableName
    ORDER BY varName varSort
    How can I dynamically sort tables in Dreamweaver 8??
    Thanks much

    In many cases you are better off sorting on the client side
    JS rather than server side. Just search the web and you'll find
    plenty of code examples.

  • My iphone will not stop going from normal calling to face time

    I have changed the settings to ensure I have turned off face time and I have also turned off the wifi feature as this is what I was told by apple. I now have been told to get a new one and start all over again

    As you can see here:
    http://support.apple.com/kb/TI73
    ... the iCloud backup works best when the iPhone is plugged in, connected to WiFi and locked.
    You should have a good strong robust WiFi connection.

  • PRINTS RECEIVED DO NOT MATCH IMAGE SUPPLIED FROM MY IPHOTO LIBRARY; CAN'T LOCATE ACTUAL MEANS TO RETURN AND GET ACCURATE PRINTS

    PRINTS DO NOT MATCH IMAGE FROM MY IPHOTO LIBRARY

    Please fix your Cap lock key - posting in all caps is =very hard to read - and is considered yelling and rude
    and pleas describe what your need - prints received form where? what version of iPhoto? If this has to do with Apple print services use the link in the confirmation email to contact Apple about yr. question
    LN

  • Going from CS4 to CS3

    Greetings,
    Once you've created a composition in a CS4 version of a program such as After Effects, are you able to open the comp in the CS3 version?
    I know this problem arises with Adobe Audition when going from Audition 3 to any prior version, and I'm looking to go back to CS3 from CS4 (far too many bugs and I'm finding it far too unstable)
    Thanks,
    Sarah

    You can copy keyframes manually if you have both versions installed on the same computer:
    i http://generalspecialist.com/2007/10/opening-after-effects-projects-in.asp
    - Jonas Hummelstrand
    http://generalspecialist.com/

  • Inventory audit report and Inventory GL balance - Not matching

    Team
    I taken the report from Inventory audit report , this is not matching with inventory charts of accounts balance.
    What may be the error
    How to close old topics, how to provide the points for good suggestion. My points also not increased , what I need to do increase my points.
    Thanks
    Anantha Desai

    Hi,
    1. Please check if any manual JE posted to that GL account
    2. How to close old topics
    There are two way close discussions:
    ----> If you got right answer, you can choose "correct answer" option in replies.
    ----> If you get an idea or suggestions, you can choose "Helpful answers" and need to close manually by choosing "Assumed answered:.
    how to provide the points for good suggestion
    Please choose "helpful answer" and "Like" option for good suggestions
    My points also not increased , what I need to do increase my points.
    Points will be increased, if you provide right suggestions, ideas and answers to other member discussion.
    Refer this document for further details:
    http://scn.sap.com/community/support/blog/2013/04/03/how-to-close-a-discussion-and-why
    Thanks & Regards,
    Nagarajan

  • OBIEE 11g Report-When drilling down to lower level, totals are not matching

    Hi All,
    I am creating a report in Analytics 7.9.6.3 , OBIEE 11g - Let’s say Budget Cost/Actual Cost based on the Date Dimension
    Have selected the Fiscal Year Dim, Fact Budget Cost, Fact Actual Cost
    FY BCost ACost
    2011 100 120
    2012 150 140
    Total 250 260
    But here when I am drilling down from Year to Quarter and Period - The values are not matching with the totals....
    FY FY Qrt BCost ACost
    2011 2011 Q1 80 100
    2011 Q2 100 90
    2011 Q3 110 120
    2011 Q4 90 130
    Total 380 440
    Fiscal Year, Fiscal Quarter Budget Cost and Actual Cost are not returning correct results – When selecting cost's by fiscal year, or filtering on a specific fiscal year, the amount returned does not equal the fiscal year total;
    when I am drilling down to Quarter and Period Level the BCost & ACosts are bumping the Numbers as above and not matching with totals
    Any suggestions?

    Check out the query in both the times.Execute against database and try to sum the data for quarter/period and compare it with Year data.
    Just try to differentiate is it a report total that is getting wrong or the data in the database table itself is getting wrong stored.
    Mark as helpful if it helps.
    Regards,
    Veeresh Rayan

  • When drilling to lower level - Totals are not matching in BI Analytics OOB

    Hi All,
    I am creating a report in Analytics 7.9.6.3 , OBIEE 11g - Let’s say Budget Cost/Actual Cost based on the Date Dimension
    Have selected the Fiscal Year Dim, Fact Budget Cost, Fact Actual Cost
    FY BCost ACost
    2011 100 120
    2012 150 140
    Total 250 260
    But here when I am drilling down from Year to Quarter and Period - The values are not matching with the totals....
    FY FY Qrt BCost ACost
    2011 2011 Q1 80 100
    2011 Q2 100 90
    2011 Q3 110 120
    2011 Q4 90 130
    Total 380 440
    Fiscal Year, Fiscal Quarter Budget Cost and Actual Cost are not returning correct results – When selecting cost's by fiscal year, or filtering on a specific fiscal year, the amount returned does not equal the fiscal year total;
    when I am drilling down to Quarter and Period Level the BCost & ACosts are bumping the Numbers as above and not matching with totals
    Any suggestions?

    Check out the query in both the times.Execute against database and try to sum the data for quarter/period and compare it with Year data.
    Just try to differentiate is it a report total that is getting wrong or the data in the database table itself is getting wrong stored.
    Mark as helpful if it helps.
    Regards,
    Veeresh Rayan

  • How do i delete an old iCloud account from phone when I forget my password and I'm not able to reset it because my security questions do not match?! Help!! Currently not able to update any apps or icloud info

    How do i delete an old iCloud account from phone when I forget my password and I'm not able to reset it because my security questions do not match?! Help!! Currently not able to update any apps or icloud info...

    If your device is signed into an old ID of yours that is an earlier version of the ID you want to sign in with, do the following:
    If you are using iMessage and FaceTime, make sure you are signed into these services with your current ID.  If they are signed into the old ID, go to Settings>Messages>Send & Receive and Settings>FaceTime, tap the ID, sign out, then sign back in with your current ID.
    Then temporarily recreate the old ID by going to https://appleid.apple.com, click Manage my Apple ID and sign in with your current iCloud ID.  Click edit next to the primary email account, change it back to your old email address and save the change.  (You should not have to verify the old email account so it doesn’t matter if you no longer have access to it.)  Now go to Settings>iCloud, turn off Find My iDevice and enter your current password when prompted (even though it prompts you for the password for your old ID).  Then save any photo stream photos that you wish to keep to your camera roll (unless you are using iCloud Photo Library).  When finished go to Settings>iCloud, tap Sign Out (or Delete Account if you are not running iOS 8) and choose Delete from My iDevice when prompted (your iCloud data will still be in iCloud).  Next, go back to https://appleid.apple.com and change your primary email address back to the way it was.  Now you can go to Settings>iCloud and sign back in with your current iCloud ID and password (your data will download back to your device).

  • Object does not match target type when raising an event from c# to VB6

    I have a c# .net DLL that I use from a VB6 app. It exposes an event,
    and the VB6 app is sinking it.
    The VB6 app is receiving the event, as long as it is raised from the
    main thread of the .net DLL.
    I have an aync task being handled inside the DLL (delegate BeginInvoke). Any
    attempt to raise the event from within that thread casuses the reported
    error, even from within the AsyncCallback function, when the thread is ending.
    I noticed that the delegate for the event is not declared inside the
    interface. It's in that module, but above the interface definition:
        [ComVisible(false)]
        public delegate void LoggingEventHandler( string logData );
    The event is declared in the class itself as:
        public class Processor : _Processor
            public event LoggingEventHandler        LogNotification;
    Finally, to raise the event:
    if ( this.Completed != null )
        this.Completed( true );
    If I open the tlb with OLEVIEW, I can see the public event just fine. Of course, I expected to, as it's working up until the helper thread kicks in.
    Now for the REAL WIERD PART! This DOES work on several servers that have
    been in production for months. It's just this one server that it won't work
    on. Same code. Resinstalled/registered it 1,000 times. It took me a while to
    find that an error was even occuring, since it was being raised in the
    seperate thread. In other words, I'm receiving the event just fine on a series of servers. This is a new machine we're trying to bring online. I suspect it's environmental, but I can't figure it out.
    I don't understand why the publisher would be expecting a certain type of
    subscriber in the first place... unless the error is really triggered by the client when the event reaches it. I've put logging into the client, though, and the first line of code inside the event is not being executed.
    For the VB6 app, I reference the tlb file that is automatically created when
    I compile (Interop is checked). I unregistered and re-registered the tlb on
    the server. I regasm'd the dll itself. All dlls are in the same folder - not
    in the GAC.
    The stack trace is as follows:
       at System.RuntimeType.InvokeDispMethod(String name, BindingFlags
    invokeAttr, Object target, Object[] args, Boolean[] byrefModifiers, Int32
    culture, String[] namedParameters)
       at System.RuntimeType.InvokeMember(String name, BindingFlags invokeAttr,
    Binder binder, Object target, Object[] args, ParameterModifier[] modifiers,
    CultureInfo culture, String[] namedParameters)
       at System.RuntimeType.ForwardCallToInvokeMember(String memberName,
    BindingFlags flags, Object target, Int32[] aWrapperTypes, MessageData&
    msgData)
       at HPFS.Queue.IProcessorEvents.LogNotification(String logData))

    This is driving me nuts!
    I sure would appreciate any suggestions.
    I got this working on one of the two machines. The other machine had some other issues, so I had it re-imaged. It's been so long since I fixed the first one, that I can't remember exactly how I did it. Plus, I did so many things to it over two weeks, that I never really felt confident, anyway. But ... I could *swear* that the last thing I did back then to get this event to flow was to re-register the DLL's TLB.
    So ... This is win 2k with FW 1.1 + SP1.
    Completed is the delagate I'm trying to invoke.
    this.Completed.Target.GetType().Name = "__comobject"
    I've tried everything. Unregistered the .tlb. Unregistered the .net DLL. Verified that the app completely failed while unregistered. Created the TLB using RegAsm /tlb syntax.
    I tried using CLR SPY. It registers nothing. It only lets me pick an EXE. This is a DLL tring to raise to an EXE.
    I've looked at the TLB in OLE VIEW and I just don't know what I'm looking at.
    Is there any other tool or technique I can use to audit/monitor/trap this? .net is giving me *** for details about what's failing. I wish I could somehow debug into exactly what it's trying to do and get more details on the failure.
    Here's the error I'm getting:
    (Code -1) Object does not match target type.<Source:mscorlib>(Stack:    at System.RuntimeType.InvokeDispMethod(String name, BindingFlags invokeAttr, Object target, Object[] args, Boolean[] byrefModifiers, Int32 culture, String[] namedParameters)
       at System.RuntimeType.InvokeMember(String name, BindingFlags invokeAttr, Binder binder, Object target, Object[] args, ParameterModifier[] modifiers, CultureInfo culture, String[] namedParameters)
       at System.RuntimeType.ForwardCallToInvokeMember(String memberName, BindingFlags flags, Object target, Int32[] aWrapperTypes, MessageData& msgData)
       at HPFS.Queue.IProcessorEvents.Completed(Boolean success)
       at HPFS.Queue.Processor.RequestDone())
    Processor = the DLL I'm trying to raise the event from.
    IProcessor = the event interface that's exposed through COM.

Maybe you are looking for