W530 Boot Failure with out any BSOD

I bought my thinkpad w530 in Oct. 2012. It works perfect until recent month.
At the beginning, it can't wake up in the sleep mode. If I connect the AC power, it reset the BIOS time.
And nowadays, when i power off this laptop, it can't boot. And I remove and setup the battery, It restored. But if I first connect the ac power/dock, and remove-setup the battery, the BIOS time is reseted.
I updated all my drivers. The failure is still here. I wonder if oneday it died forever?
Thinkpad W530 2lu, 32G DDR 3 Kinston, 500G HDD. K2000m

Can you try resetting your BIOS settings to defaults?
It's also possible that your CMOS battery is depleted, in which case you would have to replace it.
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

Similar Messages

My iphone doesn't show me the effect on picture that are taken with effect is shows me it as a normal pic with out any effect but when I press edit it shows that the effect is already on but u can see it

my iphone doesn't show me the effect of the picture that Are taken with effect it just show them to me as a normal picture with out any effect and when I go to edit it shows there that the pic already has an effect and when I see the picture in group it shows that it has effect only when I tap on one to see it larger the effect disappear

I'm having the same issue, i restored my phone to Factory settings, even tried restoring it to my backup, half of my music bought from itunes won't play on my iphone and i'm super annoyed, this only happened once i updated to ios 7.2 so i assume its another glitch to go with my imessages not sending, getting sick of this.

HTTP Receiver Adapter payload as single line plain text with out any tags.

Hi PI experts,
I have a strange problem in http receiver adapter.
Sender RFC (SAP) Receiver: HTTP.
Receiver system expects the output from XI in the below format in a single line plain text with out any tags in the payload. and the content type should be application/x-www-form-urlencoded
Group=Test&Sentinel=Web%20Server&Facility=5345&Order Number=XT-XWHM-Y-NA&Serial Number=123456&@LABEL_QUANTITY=5&@LABEL_NAME=111114_Q
Is there any way to achieve this using http receiver adapter. Business is not ready to accept the output from XI not even in a single element instead they only need it as a JUST a plain text.
Appreciate early response on this.
Thanks in Advance,
Jitender

Dear Ola,
Could you elaborate how you achieved in catching the response data from the receiver in case of HTTP receiver adapter?
The target service is not a WebService but some python script that must to receive some paramters via POST request.
HOW can I post this parameters?
Here you entered the fields of the message type of the request in the header parameters of the receiver adapter? Thats fine.
But what about the message type and vice versa of the response from the receiver?
Regards
Rebecca

My iphone 3gs ios 6.1.6 shutdown itself with out any error

my my iphone 3gs ios 6.1.6 shutdown itself with out any error & after restarting it the same thing happens please help

Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new). Try each of these in order until the issue is resolved. If the issue persists, take the device to Apple for evaluation.

User locks with out any log in event viewer

Hi,
In our active directory environment, Domain user gets locked out with out any event saved in event viewer as i am not able to see why these users gets locked.
Any help?

Hi,
Additionally information for you:
Tracing Account Lockout Source
https://social.technet.microsoft.com/Forums/windowsserver/en-US/50512220-aeb2-4eb2-b467-2b9ad9a5b2db/tracing-account-lockout-source
Regards.
Vivian Wang

I bought the production premium , cs6 , and I download it and registered with out any problem , I formatted my computer then I downloaded the collection , now everything else working only after effect is not working , what shall i do

I bought the production premium , cs6 , and I download it and registered with out any problem , I formatted my computer then I downloaded the collection , now everything else working only after effect is not working , what shall i do

did ae install without problem? check the install logs to be sure (Troubleshoot with install logs | CS5, CS5.5, CS6, CC)
if it did, what do you see when clicking the executable?

Hi, I have an early 2008 24" iMac, I need more storage space and was wondering if I could fit a 3TB Western Digital Caviar Green HDD into it with out any problems? This is the one I've seen, Western Digital Caviar 3TB SATA 6 GB/s 64MB Cache 3.5 inch

Hi, I have an early 2008 24" iMac, I need more storage space and was wondering if I could fit a 3TB Western Digital Caviar Green HDD into it with out any problems? This is the one I've seen, Western Digital Caviar 3TB SATA 6 GB/s 64MB Cache 3.5 inch

My bad?
You're original response was questions/post about an iMac. Now you've edited it to ask about a Mac Pro?
You can more easily add internal drives in a Mac Pro.
Not too terribly easy to add/replace drives in an iMac.
If younhave questions about a Mac Pro, try posting in the Mac Pro forums.
Much more knowledgeable users there.

Accessing Java Object with out any application servers

Hi,
I would be much thankful if any one guide/suggest me how to
access an java object with out using any application servers.I am
having an java object which holds dummy data and an mxml file which
contains some text fields. My plan was to access the java object
and put the dummy data in the text fields. I am using RemoteObject
for this. I am not able to proceed further. Please help me.
Thanks in advance
Regards
Karun Kumar

You can check The Merapi Project it's still in the
development phase but it'll allow to an AIR app invoke a java class
and run it as it were inside your app. But that's something you
can't take into production yet, why don't u wanna use a server
backend?

Hi, i am new to this iphone 4 and purchased it from craigslist guy with out any password on it but when i came home the itunes app asked me to put davindersihota@icloud password which i neverhave so i contact the seller to give me the password

I asked the guy to give me the password then he dissclosed that it was not his phone and he purchased from another brown guy and that he will contact him the second day he told me, he didnot have the phone number off that guy and i ask him to send an email to that email address ,but he replied no one is answering from this email account .so then i tried to restore the phone with itunes and after restoring the phone is asking to put the password for that [email protected] help me because i called apple but they didnot help me,i understand that this features is for security of i phone users in ios7 updates but what about loyal people who sold their item with out knowing these features or the person who is purchasing this item dont know that it has been protected by password. Apple must figure out some thing for their loyal customers to give them the phone number or email regarding that original phone owners ,or see if the phone is not reported as stolen so in this way they should help to activate that phone .I hope Apple will help people and not to be mean with customers.Thanks for reading is message.

You need the password of the iCloud account/Apple ID that was used to originally set up the phone. That is the activation lock/anti theft feature in iOS 7. There is no way to get around that, except by using the password.
The original seller should have disabled it, but did not. if the seller is unable or unwilling to give you the information rerquired to unlock your phone, the the phone is probably stolen. That is why you have anti theft features in the phone; to avoid a situation similar to yours.
Your phone is worthless. Sorry.

Msi Z87-GD65 Booting Failure With eSATA Drives

Hi Folks,
Before I go down the (probably ill-fated) Customer Service path I thought I'd address the forum here on a little problem I'm having with my Z87-GD65.
IN essence, if I have a hard drive connected to my eSATA port the PC won't boot. I'm using an ICYDOCK 4 bay external enclosure (MB561US-4SB if interested). If the drive itself is on but the HD trays are ejected then it boots. If any of the drives are secured then it'll hang at a post-BIOS/pre-Windows screen where all I get is a blinking cursor for about 30 seconds and then it disappears to a plain black screen. If the device is powered off then it boots.
I've checked the BIOS with one of the HDs running and it doesn't appear within my boot list - in fact, except for one selection in the bios allowing me to disable eSATA there really isn't much I can do there.
I've upgraded my BIOS to 1.30 from 1.00 and the process seems to move a bit further - now I get the oh-so-pretty ugly Windows logo and that's all.
When I do actually boot the PC with the ICYDOCK off then I'm able to get into Windows normally, and turn on the ICYDOCK. After a few seconds all 4 hard drives report in and everything's fine.
I've been using this ICYDOCK for about a year and a half, with 2 other motherboards (neither were an MSI) and i7 cores, and neither of them caused me any issues. I remember that neither of those boards had the port multiplier eSATA capability so I had to buy a controller card with that capability. I could probably dig that up and see if the problem remains.
In case you're wondering, if it helps, I built a Msi Z87-GD65/4770 i7 - based PC with 2 internal 2TB Hard Drives, and 16gb RAM. I already mentioned the ICYDOCK. I used LiveUpdate to install all the latest drivers & BIOS before uninstalling it.
I build & repair PCs for a living so I'm pretty familiar with what's going on with the system. I figure that there must be something happening between the BIOS and Windows "handoff" of the ICYDOCK, but I'm damned if I can figure out just what.

More information please. PSU, OS being used, etc..
Live Update is best uninstalled. Flash UEFI/BIOS the safer way;
https://forum-en.msi.com/index.php?topic=169827.0
Recommend to download drivers and utilities from the MSI Websites and install manually.
>> Posting Guide <<

No longer able to boot - failure with /boot

I recently, due to a hard drive change, rebuilt my desktop. Every now and again, since then, it hasn't booted. I just logged into root and rebooted; figuring I'd sort it out at some point.
Only, now it won't boot at all. When I go through journalctl -xb I get the following errors (the ellipsis, in case it isn't clear, indicate an number of lines with no error in between the error messages):
Job dev-sda2.device/start timed out.
Timed out waiting for device dev-sda2.device.
Dependency failed for /boot.
Dependency failed for Local File Systems.
Triggering OnFailure= dependencies of local-fs.target.
Dependency failed for File System Check on /dev/sda2
and also, much later in the logs:
Failed at step EXEC spawning /bin/plymouth: No such file or directory
My initial assumption would have been that the relevant drive is failing, but I only recently ran a check on the drives (a few days ago and since the rebuild) and all was fine and dandy - but I had already been seeing these errors on a periodic basis. Only now, as I said, they happen at every boot and I never get as far as login.
Thanks in advance for any help.

I ran the extended smartmontools test on the disk today and it returned with no errors. However, the error log for the disk did contain the following:
Complete error log:
SMART Error Log Version: 1
Warning: ATA error count 21 inconsistent with error log pointer 5
ATA Error Count: 21 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 21 occurred at disk power-on lifetime: 10341 hours (430 days + 21 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 00 00 00 e0 08 01:12:12.224 READ DMA
27 00 00 00 00 00 e0 08 01:12:12.224 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 0a 01:12:12.224 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 0a 01:12:12.224 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 08 01:12:12.224 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 20 occurred at disk power-on lifetime: 10341 hours (430 days + 21 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 00 00 00 e0 08 01:11:26.048 READ DMA
27 00 00 00 00 00 e0 08 01:11:26.048 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 0a 01:11:26.048 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 01:11:26.048 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 08 01:11:26.048 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 19 occurred at disk power-on lifetime: 10341 hours (430 days + 21 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 00 00 00 e0 08 01:10:16.816 READ DMA
27 00 00 00 00 00 e0 08 01:08:51.584 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 0a 01:08:51.584 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 01:08:51.584 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 08 01:08:51.568 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 18 occurred at disk power-on lifetime: 10340 hours (430 days + 20 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
25 00 01 00 00 00 e0 08 00:04:28.384 READ DMA EXT
c6 00 10 00 00 00 e0 08 00:04:28.384 SET MULTIPLE MODE
91 00 3f 00 00 00 a0 08 00:04:28.384 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 08 00:04:28.352 RECALIBRATE [OBS-4]
25 00 01 00 00 00 e0 04 00:04:28.352 READ DMA EXT
Error 17 occurred at disk power-on lifetime: 10340 hours (430 days + 20 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
25 00 01 00 00 00 e0 08 00:04:28.288 READ DMA EXT
c6 00 10 00 00 00 e0 08 00:04:28.288 SET MULTIPLE MODE
91 00 3f 00 00 00 a0 08 00:04:28.288 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 08 00:04:28.272 RECALIBRATE [OBS-4]
25 00 01 00 00 00 e0 04 00:04:28.272 READ DMA EXT
Does this mean my disk is dying? That would be very annoying after just rebuilding from another failed disk!

Boot failure with AMD core unlock *solved*

Before you criticize me for buying a triple core instead of a quad core, I want you to know that my situation seems to only conflict with Arch.
I have an AMD Athlon II x3. If I unlock the 4th core, Linux live CDs boot up just fine, Windows XP boots fine, Windows 7 boots fine, and as long as any OS completely boots up it runs flawlessly for hours with constant load. However, Arch will fail to boot IMMEDIATELY after unlocking cores. IIRC, the Arch setup CD also fails to boot. I have a small feeling that GRUB has something to do with it, but whenever I attempt to install GRUB2 I'm never able to boot again.
As another note, I can't seem to get IOMMU to work with Arch. With Debian based distros it works immediately, but I can't find anything on how to enable it with Arch. I get this impression that there's a lot of missing Kernel entries in Arch which are causing these CPU problems, and possibly others.
Last edited by schmidtbag (2011-09-27 16:16:30)

schmidtbag wrote:
R00KIE wrote:Not much of an idea then, get /proc/config.gz from the distros that work and the one from arch, compare them and see if you can spot what might be causing the problem. No other ideas here.
debian doesn't have that file, did you mistake it for something different?
I know some distros don't have it but I wasn't aware debian is one of them (I use arch everyday and I try to manage a few centos boxes and that's all), that is an option can be enabled/disabled when building the kernel and it can be quite useful when trying to figure out why something doesn't work (such as seeing which drivers were built and which option was selected when there are multiple choices), however I guess it might have security implications since anyone can find out which options were selected when building the running kernel and some combinations may have yet uncovered/unpublished/undisclosed security exploits.

NAC Server and Manager Failure with out failover

Hi, I'm working on a NAC L2 OOB wired design with 1 CAM and 1 CAS. I've not included failover to the design for the obvious financial reasons, and want to figure out the affect that the network would have in the case of a failure.
1.)What would the users experience in the event of a CAS failure? both currently online users and new users
2.)What would the users experience in the event of a CAM failure? both currently online users and new users
3.) Are there any ideas on how to minimize the effect on the users in the event of a failure, w/o adding failover bundle ?
Many thanks for your valuable input in advance.
Din

If you are out OOB, then a CAS failure would not affect logged in, remediated users, anyone not logged in would be stuck because when the CAS fails, the connectivity to the CAM would be lost.
If the CAM fails, you will not be able to log in, do remediation or anything. VLAN settings on switches will be frozen where they are at the moment of CAM faiure. Not that you could easily connect to switches, change vlans to allow users onto the LAN and the CAM would accept that passively when restarted but if you use the Agent it will probably want to log in again, which is not a huge issue if you use AD SSO.
Dan Sichel
Dan S.

Swap boot drive with SuperDuper -- any tips?

I'm using a Mac Pro 3,1 and my 300GB boot drive is getting a bit tight. I'm thinking of swapping it out with a larger drive; I do daily cloned backups of my boot drive using SuperDuper, so it seems like a swap would be as simple as switching boot drives to my backup, swapping out the HD, and cloning everything back onto the new larger drive. That seems too simple, though; is there anything I should watch out for?
And on that subject, any suggestions as to reliable internal drives to upgrade to?

Be sure to prep the new drive properly:
Drive Preparation
1. Open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
Most any drive you choose will be fine, although personally, I'd avoid Western Digital Blue models and any "green" models from other mfgrs. I'm partial to Hitachi and Seagate.

Welcome page with out any password pop up

Hi All,
I have one req. that we have to make one BSP page in page with flow logic. And that page should not ask for any user id and password. Can you please help me out?
Thanks and regards,
Kuldeep Verma

Hello Kuldeep,
If the BSP application contains the Welcome page as well as other pages, you can achieve the goal through dividing the application into two parts: public part and protected part.
For example, for the Welcome page, you can create a page with name "public/welcome.htm", and for other pages that must be accessed with user authorization, you may create each page with name "protected/xxxx.htm".
In addition to the above, you need to create two independent services under SICF relevant node for the BSP application. As in example, one independent service is named "public", and the other is named "protected". For "public" serive, you need to specify a user that has limited rights; for "protected" service, you do not need to specify any users.
Please reward points if helpful!
Best regards!
Gordon

W530 Boot Failure with out any BSOD

Similar Messages

Maybe you are looking for