W530 will only boot after being left off for hours

I just purchased a Thinkpad W530. it has worked beautifully other than one major problem: it won't start up after a shutdown unless I leave it off for hours. I can turn it on after being off and it works just fine, but if I turn it off I have to almost wait overnight for it to turn back on again. I hit the power button, the green light comes on for a few seconds and then it turns off again.
I've tried booting with just the AC adapter and just the battery. I've also tried unplugging both and holding the power button for 30+ seconds and then plug it back in and it does the same thing. I ran the hardware diagnostic test provided by Lenovo when I'm able to actually get it to work but the results (albeit it's nowhere near a comprehensive test) appear to be fine. I also tried changing what slot the RAM is inserted in.
Also, it has never shut down or anything randomly and it won't turn on no matter how long I had it on so I don't think it's a heat related issue. I had it on for under a minute yesterday morning and then turned it off and it wouldn't turn on until this morning.
Thanks in advance for any ideas!

I think it IS a heat issue, but not overheating. You probably have a defective chip on the motherboard (part of the starting circuit) that only works when cold. I assume it has a warranty. Now is the time to get service.

Similar Messages

Mac book pro mid 2009 shuts down after a few hour then will only boot after waiting and pressing power button numerous times. I am running mountain lion with most recent updates.

Mac book pro mid 2009 shuts down after a few hour of use and then is very difficult to reboot. Sometimes I have to wait hours, sometimes I have to repeatedly press the power button and then it will slowly start a little longer each press untill it completely boots. It has done this three times know. Each time I was watching a video.

Try running the Apple Hardware Test - sounds as if you've hardware issues.
Clinton

MacBook Pro won't start after being powered off for extended period of time

Hi all, I have a 2013 MacBook Pro (OS X Mountain Lion) that I've owned for about fourteen months. I have just been away for several weeks, during which time my computer has been left completely powered down. However, now it will not start up again. When it is plugged in, the startup sound will play, but the screen stays black. The indicator light on the charger switches back and forth from green to orange several times. The battery indicator lights on the side of the laptop all blink at first and then one lights up a solid green when the button is pressed. I left it plugged in to charge overnight, but nothing has changed since yesterday. After reading several other forums, I have tried starting it up using (ctrl+opt+shift+power) as well as (ctrl+opt+P+R+power), but I got the same result both times. If anybody has any suggestions, I'd be very grateful. Thanks!

• Already tried that.
Yes you did, and you said so in your post. Sorry - my fault I did not read the complete post.
What model MBP is this? Removable battery?

Is it dead? will only boot off the OS disc or in safe mode.

Hi there!
Is it dead? will only boot off the OS disc or in safe mode.
My MBP (March 09) running 10.6 Snow Leopard is playing up.
After a frustrating day of troubleshooting, I don't know what else to do.
So far:
Duplicate accounts deleted.
Permissions repaired and verified
Renistalled the OS from disc
Haven't been able to log in to OS since,
- can only boot in safe mode or OS istall disc to use Utility
Disk Utility used in safe mode, disk utility > verify disk, said to repair it from disc boot
Disk repaired
Still won't reboot out of safe mode - it gets past the blue screen to the desktop wallpaper screen, but the dock or items on my desktop won't appear, colour dial spins, i think the longest i've given it is 20 minutes
Still won't boot other than in safe mode (currently using it right now)
Did the whole /sbin/fsck -fy,
Invalid file count (Is 484158 instead of 484160)
Invalid volume directory count (is 157609 instead of 157807)
Repairs successful
Ran fsck again, and HD OK message
Ran exit and it won't boot, only in safe mode again, and to the spinning wheel on the desktop wallpaper screen.
Is my HD cactus?
Is this something that can be replaced?
If not, what next?
I'm a little apprehensive about sending it out to get fixed (it's out of three year warrnaty) and I'm not sure how much more they can do/check than I've already done and come to the same conclusion.
Any help, much appreciated and thank you in advance
Bree.

Are you referring to the new bluetooth (wireless) keyboard or are you using a wired version?
Message was edited by: Barbara Daniels1

My computer will only boot off it's drive in safe mode

Short Story...
My computer will only boot in safe mode and in normal mode displays grey apple that turns into a grey cross. Surface scan in techtool pro 4.5.1 passed
Long Story... (all the issues I've had as they are all back to back and most likely cause by what sloved the previous one).
When i first got my macbook i already had a 500gb hdd in my macmini running 10.6 (or 10.6.1 I forget) and as soon as a had the macbook running off this drive it would give me one error for each and every movie file that was visible (in an open folder or on the desktop) saying quick look helper had unexpectedly quit. I tried everything and for some reason ended up changing all the permissions on the computer which royally screwed it up. anyway after repairing permissions in disk utility the error messages stopped but shortly after start up it was giving me a couple of dozen error messages saying something about .kext's (if requested i can supply full text of this error message) so i tried reinstalling the OS and since in 10.6 there is no archive and install (without messing around in terminal) i just ran the snow leopard disc which brought me back to 10.6 then I upgraded to 10.6.2 and restarting a couple of times over a day or so. After a few restarts I found the computer wouldn't start (it chimed, loaded up the apple symbol and loading wheel and then after a few minutes replaced the apple symbol with a crossed circle) I tried running the snow leopard disc again and this time not upgrading but after about 3 restarts the same thing happened. now i can only start up in safe boot mode or off my backup drive which still displays a few dozen of the .kext errors at start up. Sorry about the length of this description I would appreciate absolutely any help or ideas.

Tezz wrote:
Short Story...
My computer will only boot in safe mode and in normal mode displays grey apple that turns into a grey cross. Surface scan in techtool pro 4.5.1 passed
I would try troubleshooting your problem [using the steps given by Apple here|http://support.apple.com/kb/TS1892].

Now wifi will not turn back on automatically in the morning after being turned off all night. Use to be ok before now. Is it the new update 7.1? Help

Wifi will not turn back on in the morning after being turned off all night, it use to work for years. Is it the new 7.1 ?

Yes that what I mean, after the phone has been turned off all night, when I turn it back on the morning the wifi will not turn on by itself. Eventually by turning off and on the main phone switch and the wifi in settings it sometimes come back on! Then I'm ok for the rest of the day even when I leave the house and come back it's ok. Only first thing in the morning, strange that it doesn't wake up like it use too.
Thank you

HT3024 after installing airport extreme card into g4 ibook 1.07ghz 512 ram it will only boot to open firmware, any ideas why? please help!

after installing airport extreme card into g4 ibook 1.07ghz 512 ram it will only boot to open firmware, any ideas why? please help!

Hi David,
Have you done a PRAM reset, CMD+Option+p+r...
http://support.apple.com/kb/HT1379
In fact, do 3 in a row, takes a bit of time.
Tried resetting the PMU for PB/iB?
http://docs.info.apple.com/article.html?artnum=14449

My iMacG5 will only boot to white screen, gray apple and spinning gear. Help?

My iMacG5 will only boot to white screen, gray apple and spinning gear. Help?
Also not totally sure if it's an Intel based computer, but that's what I recall. Any way to check, since I can't get to About This Mac window?
It's running on OSX Leopard 10.5.4
First symptom = running slowly - then it kind of froze with color wheel spinning - thought a forced shut down would help - help power button til off, then white screen, gray apple and spinning gear.
Have tried...
1. Turn off the computer by choosing Shut Down from the Apple menu, or by holding the power button until the computer turns off.
2. Unplug all cables from the computer, including the power cord.
3. Wait 10 seconds.
4. Plug in the power cord while simultaneously pressing and holding the power button on the back of the computer.
5. Let go of the power button.
6. Press the power button once more to start up your iMac.
Then try booting from your install disc again.
- No change
And...
Booting From An OS X Installer Disc
1. Insert OS X Installer Disc into the optical drive.
2. Restart the computer.
3. Immediately after the chime press and hold down the "C" key.
4. Release the key when the spinning gear below the dark gray Apple logo
appears.
5. Wait for installer to finish loading.
- The fan just got louder.
Thanks for your help.

You need to do an Erase and Install or an Archive and Install depending on whether the hard drive is OK or needs to be reformatted.
Start by booting from your Leopard DVD. The rest is just following directions.
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

Will Not Copy After Being Idle

THIS IS A COPYING ISSUE!!! After installing the upgraded version of Comcast's latest modem/router, our HP 6550 would not print. I contacted Comcast and reported the difficulty and they informed me it was a printer problem - not their new modem. Consequently, we purchased a new HP 5740 printer The printing function worked fine and it would copy immediatley after the printer was turned on, however, after the printer sat idle for a couple of hours, the copy function would not work. If you then turned the printer off and immediately turned it back on, it would copy. Again, Comcast reiterated it was a printer problem. I returned the original 5740 back to the store from which it was purchased and exchanged it for another HP 5740 printer. After hooking up the second HP 5740, the same problems with copying occurred. I returned the second HP 5740 to the dealer for a refund and left town for three months. We recently returned and purchased a HP ENVY 7645 printer from another dealer. We are having the same issues with this printer as we had with the two previous HP 5740 printers. I discussed the situation with a level II supervisor at Comcast and he arranged for a new modem/router to be brought to the house and installed by a technician. The installation occurred today and we are still experiencing exactly the same problem. The Comcast technician who installed the new modem/router (who couldn't wait around while the printer sat idle) said that if the problems occurs after the installation, we should purchase a printer/copier from another manufacturer - or turn our printer "off and then on" when we want to copy. He also asid that if this problem does continue after the new modem/router is installed, it definitely won't be a Comcast problem. DOES ANYONE HAVE ANY IDEA WHERE I SHOULD GO FROM HERE?

Hi @lamoso,
Welcome to the HP Forums!
I understand that your HP Envy 7645 will not copy after being idle. I am happy to look into this for you!
I believe this is happening due to the printer going into sleep mode. As the options are for 5 minutes, 10 minutes, and 15 minutes for sleep mode to activate. I would recommend trying a hard reset, by going to this post,How to perform a Hard Reset, by @Rich1. It is important that the printer's power cable is plugged directly into the wall outlet, and not a surge protector. See this article, Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector for more information. This applies to Inkjet printers as well.
After the hard reset, I would then make sure the printer's firmware is up-to-date. Getting the Latest Firmware and Product Updates.
Let's see what happens after giving these two steps a try!
Thank you for posting!
“Please click the Thumbs up icon below to give me a virtual high-five for responding.”
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

My macbook pro will only boot in safe mode

Hey,
I have a macbook pro 15-inch, Early 2011 running osx 10.9.4. I have a SSD hard drive that i installed myself a year ago and hasn't shown any defects. Its a 120 gb OCZ-AGILITY3.
My problem:
My macbook will only boot in safe mode nowadays. I have done a complete erasion of my hard drive and installed osx mavericks twice already. After the installation the computer will safely go to the desktop. But if i then do a reboot it won't get further than after the first apple logo, sometime the turning wheel will pop up, before turning off and trying again. i have tried resetting PRAM, I have tried resetting SMC, i have tried avoiding SMC (with big fan rate), but all with no success.
I have done a complete hardware test (the longer one) and it showed "no troubles found".
My guess is that the problem is with the battery. My computer won't run anymore without the adapter, when i pull the adapter out it either stays on for a while before just turning off. Without having it plugged in it won't start. Is it possible that during normal start up there is some kind of communication with the battery that can cause this?
I ran a diagnostic shown in this thread (Will only boot in safe mode) and included it in this post.
Hope someone can help me out.
Thanks,
Bram
Start time: 17:07:42 08/25/14
Model Identifier: MacBookPro8,2
System Version: OS X 10.9.4 (13E28)
Kernel Version: Darwin 13.3.0
Boot Mode: Safe
Time since boot: 10 minutes
Battery
Condition: Replace Now
Diagnostic reports
2014-08-25 UserEventAgent crash
Log
Aug 26 00:41:52 Previous Shutdown Cause: -128
Aug 25 16:23:38 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Aug 25 16:24:05 process rpcsvchost[94] thread 917 caught burning CPU! It used more than 50% CPU (Actual recent usage: 99%) over 180 seconds. thread lifetime cpu usage 100.014147 seconds, (82.533432 user, 17.480715 system) ledger info: balance: 90006319931 credit: 100003230498 debit: 9996910567 limit: 90000000000 (50%) period: 180000000000 time since last refill (ns): 90079246240
Aug 25 16:25:50 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Aug 25 16:58:05 jnl: b(1, 3): replay_journal: from: 9340928 to: 9773056 (joffset 0x37a000)
Aug 25 16:58:05 jnl: b(1, 3): examining extra transactions starting @ 9773056 / 0x952000
Aug 25 16:58:05 jnl: b(1, 3): txn starting at 9773056 (9773056) @ index 80 bnum 2696544 (8192) with disk cksum != blhdr cksum (0x93b69228 0xc647562)
Aug 25 16:58:05 jnl: 0x662b0000 0x451b0000 0x2a0001ff 0x40000000 0xd7330300 0x46001d00 0x6c006f00 0x65006400
Aug 25 16:58:05 jnl: b(1, 3): restarting journal replay (9340928 - 9773056)!
Aug 25 16:58:05 jnl: b(1, 3): replay_journal: from: 9340928 to: 9773056 (joffset 0x37a000)
Aug 25 16:58:05 jnl: b(1, 3): journal replay done.
Aug 25 16:58:06 Previous Shutdown Cause: -128
Aug 25 16:59:26 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Aug 25 16:59:59 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Activity
CPU: user 17%, system 4%
CPU per process: WindowServer (UID 0) is using 30.5 %
launchd
/System/Library/LaunchAgents/com.apple.AirPortBaseStationAgent.plist
- com.apple.AirPortBaseStationAgent
Contents of /System/Library/LaunchAgents/com.apple.AirPortBaseStationAgent.plist (XML document text)
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
<key>Label</key>
<string>com.apple.AirPortBaseStationAgent</string>
<key>EnableTransactions</key>
<true/>
<key>LowPriorityIO</key>
<true/>
<key>LimitLoadToSessionType</key>
<string>Aqua</string>
<key>POSIXSpawnType</key>
<string>Background</string>
<key>LaunchEvents</key>
<dict>
<key>com.apple.distnoted.matching</key>
<dict>
<key>com.apple.airport.agent.prefschanged</key>
<dict>
<key>Name</key>
<string>com.apple.airport.agent</string>
</dict>
</dict>
<key>com.apple.bonjour.events</key>
...and 21 more line(s)
Spotlight: Indexing and searching disabled
Font issues: 11
Wi-Fi
link auth: wpa-psk
Restricted files: 1
Elapsed time (s): 278

Actually it sometimes gets a little further, the display will dim and the pointer will appear and then whoop it will turn off. if i do a verbose start up, it will finish all the steps, the white screen will appear and dim and then it will turn off.

24" iMac will only boot in safe mode

Here is the short version:
I have a 24" iMac Core 2 2.16 GHZ with Lion installed (has been for a long time). It will only boot successfully in safe mode. The AHT Extended tests do not report any problems. I have reset PRAM and SMC. Nothing helps. Normal boot process will get to the point where it switches from the Apple logo with spinning wheel to where it would normally switch the OSX GUI and login screen. Instead the screen is all white or gray. The exact same problem happens if I try to boot from an OSX Install DVD or USB and also my DiskWarrior DVD. Since safe mode works, my guess is that the problem is with the video card and the normal color depth that the Mac boots to. In Safe Mode it is in reduced colors.
Since safe mode works, I have all of my data backed up to an external drive. If I could boot from an install disk, I would have already wiped the disk and done a new install, but I cannot do this! I am assuming this is a hardware problem and given the age of this iMac I am out of luck. I ordered a new system last night, but if it is possible to get this one working again, I would like to be able to give it to a relative who could use it. So if anyone has any ideas, it would be appreciated.
Just slightly longer version:
Been using this system since 2007. Used to use it for work, now it is the home media hub where we sync our iOS devices. It has had Lion installed for probably a year now and has always worked great. A few weeks ago, it started locking up whenever my son was playing Minecraft. I would have to power off the system to get it back. I assumed it was a Java problem. I tried fixing disk permissions etc. but nothing solved it. Anyway, last week I was downloading App updates in iTunes when the system locked up again. The mouse would move around but I could not Force Quit anything or really do anything. So I had to power off the system. That is when the boot problems started. Since that happened, the system has not come back with a normal boot.
Thanks for any ideas/help. If someone thinks this is fixable, I can bring it to my local Apple service dealer. I do not want to pay them $100 just to have them tell me it cannot be fixed or needs a new logic board or something like that which would not be worth buying.
Mark

Please read this whole message before doing anything.
This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
These steps are to be taken while booted in safe mode.
Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
The commands may line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then either copy or drag it. The headings “Step 1” and so on are not part of the commands.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Step 1
Triple-click the line of text below to select it. Copy the selected text to the Clipboard (command-C). Then click anywhere in the Terminal window and paste (command-V).
find /Sy*/L*/Ex* -type f -name Info.plist -exec sh -c '/usr/libexec/PlistBuddy -c "Print :CFBundleIdentifier" "$1" 2> /dev/null | egrep -qv "apple|Accusys|ArcMSR|ATTO|CalDigit|HighPoint|hp-fax|JMicron|print|SoftRAID|stex" && echo ${1%*.kext/*}.kext' {} {} \;
Post the lines of output (if any) that appear below what you just entered (the text, please, not a screenshot.) You can omit the final line ending in “$”.
Step 2
Repeat with this line:
ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts 2> /dev/null
Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
Step 3
osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null
Remember, these steps are all copy-and-paste — no typing. Also remember to post the output.
You can then quit Terminal.

Qosmio X305 will only boot in safe mode or when the graphics card disabled

Hi All
I am having a very concerning issue with my laptop (Toshiba Qosmio X305). It will only boot in safe mode or if I disable the graphics card.
Awhile back I upgraded the drivers for the nVidia 9800M GTX from the nVidia website, it worked fine for awhile, but then it started crashing randomly by giving me a full screen of random color then switching off. I fixed this by rolling back to the previous version of the drivers (the drivers that came with the laptop software).
After that it working perfectly for months but yesterday my machine started crashing and I could not get it to boot correctly.
I have completely deleted (not just a quick format) both the hard drives that came internally in the laptop and I have installed a clean version (the out of the box option) of the x64 Vista that came with the laptop from the recovery disks I created. After I did the install, it boots fine as only the standard VGA device is used, as soon as I installed the driver off the drivers and applications disk it would not boot correctly:
Just after the status bar comes up and it is about to show the windows logo, just before login, I get a black screen. I can hear that it is booting fine and I can even log in to windows and by memory make things run, but I can't see anything. I then got the latest drivers, again from the nVidia website and they are not helping at all.
My system is as follows (nothing has been added, its is just how I got it):
Vista Ultimate x64
4.00 GB RAM
Intel Core 2 Quad
Like I said previously it is a clean install of the operating system, I have not added any programs, except for installing and then updating the display drivers.
Any help would be much appreciated!

Hi buddy,
It seems that this is a typical example, that only pretested display drivers from Toshiba should be used. Why?
The nVidia drivers are not pretested and they dont have an overheat protection. So for me it sounds like that the nVidia driver has destroyed your graphic card. That means no driver will help you and reinstallation of the whole system too.
I think the only option is replacing the graphic card. Therefore you should contact an authorized service provider in your country. Here you can search:
http://www.csd.toshiba.com
Explain the whole story and then you will see, what the technicians say. If your notebook is under warranty, hopefully this will be covered too. Normally other display drivers you have to install on your own risk
Good luck! :)

HP Pavilion 15-n268sa will not boot after windows update (windows 8.1)

After a series of windows update (windows 8.1) my HP Pavilion 15-n268sa will not boot up, no fan noises, no lights no nothing.
I have tried a "hard reset" a number of times with no success.
When the battery is present the white LED flashes 3 times when the power button is pressed.
Please please help.

Hello Cuffy,
Welcome to the HP Forums!
I understand you notebook will not boot after a series of Windows updates.
Can you tell me if you are able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on? If you can access this, try doing a system restore to before you installed the updates. If not I would suggest you go through this document: Computer Does Not Start and the LEDs Blink or the Computer Beeps.
If it's the Caps Lock light that is blinking this document will tell you exactly what the error is (spoiler: 3 beeps is a memory failure). This could also explain the failed updates. The updates are stored in the RAM before being applied to the operating system.
You can try reseating the RAM, or using only 1 of the RAM cards, as you have 2x4GB cards. If it still doesn't work with 1 card, try the other card to confirm it has failed.
You can replace defective cards via HP Phone Support if covered under warranty or at the HP Part Store if not covered. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
Hopefully this information helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

My Iphone will only charge when it is off???

I just got my iphone 4 about around june of this year and ever since two or three days ago I plugged my phone in because it was dead and it would not charge but when i got it home to charge it it charged all the way and not today its doing the same thing it will only charge when it is off and then as soon as the cord powers it back on it will stop charging and say 10 pecent batt left... I bought a new cord and it still does not charge my phone idk what to do this is really annoying i also tried my charger in another iphone 4 and it charged that phone so its not the cable it has to be the phone but the phone is brand new and never has been damaged i am going to verizon to hopefully get a new phone but in the mean time looking for any suggestions or tips or maybe somene is having the same problem too

Also when i have the charger plugged in after the phone dies it will show the charging batt symbol but as soon as it powers back on it says 10% battery life again and then when i power it off WITH THE CHARGER STILL CONNECTED the phone will not show the charging battery symbol again whihc means i have to take the charger out and put it back on and it dose it all over again charges with off but as soon as it powers on automatically it stops charging

How can I transfer files from a 27" iMac which will only boot in safe mode?

My late 2009 27" imac is having issues and will only boot in safe mode. I have tried to transfer files to a new Imac using migration assistant but it wont let me. If I try booting the old Imac normally I just get a grey screen, I believe it is the video card failed and am waiting for a fix, but I would like to transfer files before the fix in case something goes wrong and I lose everything.
Any help would be great

Hello Myles, likely it is a Hardware problem.
One way to test is to Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, Test for problem in Safe Mode...
PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive
Reboot, test again.
If it only does it in Regular Boot, then it could be some hardware problem like Video card, (Quartz is turned off in Safe Mode), or Airport, or 3rd party add-on, Check System Preferences>Accounts>Login Items window to see if it or something relevant is listed.
Check the System Preferences>Other Row, for 3rd party Pref Panes.
Also look in these if they exist, some are invisible...
/private/var/run/StartupItems
/Library/StartupItems
/System/Library/StartupItems
/System/Library/LaunchDaemons
/Library/LaunchDaemons

W530 will only boot after being left off for hours

Similar Messages

Maybe you are looking for