WAAS 4.1.1c Upgrade causing issues with intranet site access

We recently upgraded to 4.1.1c and are now experiencing page not displayed errors when accessing our intranet site via the WAN. Disabling the HTTP AO fixes the issue, so I believe we may be experiencing bug ID CSCsv69306. Any idea when there will be a fix for this as we could really use the http acceleration since there is a significant amount of http traffic on our WAN.

Jeff,
If you are encountering CSCsv69306, then it's scheduled to be fixed in release 4.1.3 which is due out mid-late March.
Hope that helps,
Dan

Similar Messages

Exchange upgrade causing issues with internal wiri...

Recently our exchange was upgraded to accommodate bt infinity and at the same time our broadband started playing up. we called bt and I spent 1.5 hours checking and re checking equipment with the call center. Tests were done with the hub at either end of the internal wiring. All the tests were still showing faults even with hub connected to the test socket. They asked me to leave connected for 24 hours while they monitor the line. They promised to call me back which they did not. I called them again the following day to be told I should have left the hub in the test socket which I was not told the previous day. I then had to wait 48 hours while they monitored the line this time in the test socket. All the tests still showed the fault was still there so an engineer called out.
The hub was still in the test socket when engineer arrived and the first thing he did was hook up his test equipment to the test socket and he stated there and then that there was nothing wrong with the line but it had been throttled down. 2 minute phone call and 10 minutes later broadband was back and working perfectly at the test socket. He checked the internal extention and the faults were being thrown up by an extension that has been in place for 10 years +. He stated to me that the new equipment installed in the exchange was more advanced and did more line checks so, although this equipment has been used for Internet with BT for 10 years it is no longer adequate.
All of this I find understandable but the whole way that BT handled this from day 1 of my first call has been appalling. BT openly admitted that the original engineer calls were handled badly and we were credited £9 for the lack of services we had for overly long time. However we are now, 2 months after this, faced with nearly £130 charge for the engineer visit which, looking back with the info I have now, was completely unnecessary. Had the engineers on the phone bothered to reset the line while hub was in the test socket when they were allegedly monitoring it for 48 hours they could have told me there were no faults on their equipment up to the socket and I would have sorted out the internal wiring myself. Even now I can find mention on the Internet of old wiring causing issues but no specific posts to do with exchange upgrades potentially meaning that you need to upgrade internal wiring or mention by the BT call center itself on any of the calls I made to them. All I was told was that everything up to the main box is BT and everything after that mine but since we have made no changes to the wiring we did not think it was applicable until the engineer arrived and told us what he told us then. Yesterday I called Bt again around 9am to dispute the charge. I was informed that because the fault was with our equipment the charge stands. I explained all of the above and I had my case put to the review team. I was told I would get a call back within 4 hours which I did but the phone rang 3 times and as I answered they hung up. I then got a text saying they had tried to call and asked for me to call back which I did to be told that his computer wasn't working. He took my details and said someone would call me back which no one did. I chased again to be told that someone would definitely call me that day. No one did. I chased again today to be told the decision still stands. He has put to final review and promised a call back within 5 days. Until this is resolved direct debit is cancelled. To the letter of the contract we have with BT this is our charge to pay I know that but this could have been avoided if the information was out there on the net, if the original checks done over the phone were done correctly or if I had been told this directly by Bt themselves prior to the engineer being called out which is why I am posting this here so hopefully no one else falls into this trap.

You're right I'm not connected to the BT infinity cabinet. But the BT Infinity cabinets all still route back through the exchange that I am connected to -
http://www.ichilton.co.uk/blog/phones/faster-broadband-bt-infinity-fibre-to-the-cabinet-coming-to-in...
Quote :
What this modem does is connects using VDSL from your home to the VDSL cabinet using the existing copper wires, on to the DSLAM, back to the exchange (over the fibre) and on to BT’s core network.
Your phone line is then still terminated in the original cabinet for telephony (using the cross connect between the old and new cabinets I mentioned above) and back to the exchange over the original multi pair copper cable as it always has done.
http://www.robertos.me.uk/html/fttx.html
Quote:
FTTC involves BT Openreach installing a new street cabinet near to the existing one and linking the two. They run optical fibre from the exchange to the new cabinet then link individual lines from the old cabinet to the new one and back to get VDSL2 onto the copper connection to the premises. The PSTN phone connection continues to operate over the pre-existing cable from the old cabinet to the exchange. It does not get put onto the fibre connection.
In other words the linkage is Exchange >> Old >> DSLAM in New >> Old >> Premises. (Traffic in both directions of course!)
Presumably the equipment in the exchange cannot stay as it is and is upgraded in the process?

Web Logic 10.3 upgrade causes issues with escaped characters in JSP.

We recently upgraded our application servers from Weblogic 9.2 to Weblogic 10.3 and we are having an issue with escaped characters in a JSP code. Here is an example of what we are seeing:
var convertedBody1 = document.getElementById('body').value.replace(/\$FIRST_NAME\$/g, firstName);
This code works in Weblogic 9.2. In Weblogic 10.3 we have to make the following changes:
var convertedBody1 = document.getElementById('body').value.replace(/\$FIRST_NAME\$/g, firstName);
Thanks, Tom

Hi:
I have resolved the issue with the following in the jspx page.
Put an
<jsp:scriptlet>
response.setContentType(“text/html; charset=UTF-8”);
</jsp:scriptlet>
Inside the <f:view> on the jspx file.
Please refer the link http://www.oracle.com/global/il/support/tip/nlss11061.html for more details. It is helpful.
Thanks & Regards
Sridhar Doki

Yosemite upgrade causing issues with Adobe Premiere Elements 10

Hi,
Over the last weekend I upgraded my mid-2010 iMac to Yosemite from Snow Leopard and it seems to have caused an error with Adobe Premiere Elements 10.
Prior to upgrading I was working on a project without issue. Now, when I try to open it I get an error "The project is not compatible with current version of Premiere Elements".
I have tried other projects and some open without issue whilst others also present the same error. The difference between the projects appears to be whether a DVD menu has been selected. If the project has one - it fails to open.
It seems strange that the OS would affect software in this way but that is all that has been changed.
If someone can shed some light on this it would be greatly appreciated.
Thanks

Hi,
Over the last weekend I upgraded my mid-2010 iMac to Yosemite from Snow Leopard and it seems to have caused an error with Adobe Premiere Elements 10.
Prior to upgrading I was working on a project without issue. Now, when I try to open it I get an error "The project is not compatible with current version of Premiere Elements".
I have tried other projects and some open without issue whilst others also present the same error. The difference between the projects appears to be whether a DVD menu has been selected. If the project has one - it fails to open.
It seems strange that the OS would affect software in this way but that is all that has been changed.
If someone can shed some light on this it would be greatly appreciated.
Thanks

Upgraded to IO6, seems like the amount of system memory to run is higher, this causes issues with some Apps. I can't get SIRI to work because the amount of free system memory is not enough. how can I tell what is eating the system memory?

Upgraded to IO6, seems like the amount of system memory to run is higher, this causes issues with some Apps. I can't get SIRI to work because the amount of free system memory is not enough. how can I tell what is eating the system memory?

Upgraded to IO6, seems like the amount of system memory to run is higher, this causes issues with some Apps. I can't get SIRI to work because the amount of free system memory is not enough. how can I tell what is eating the system memory?

MovieClip Filter Causing issues with EventListeners (mouseEvent.ROLL_OVER)

Hello,
I have been working on a flash photo gallery for the web. It loads thumbnails from an xml file into a loader which is then made the child of a movieclip.
The thumbnails are animated and triggered with mouse events of ROLL_OVER and ROLL_OFF. I have this working, or appearing to, when the movieclip containing the loaded thumbnail has no filters applied to it.
I want add a drop shadow on the ROLL_OVER event and remove the drop shadow on the ROLL_OFF event. I also have this working, however my problem arises when I mouse over the very edge of the movieclip. This cauese the ROLL_OVER and ROLL_OFF function to fire in rapid succession, creating a flashing dropshadow. This looks aweful and I really have no idea what would be causing this issue.
Thanks in advance for any advice!
Regards.

Thanks for the reply.
I also found it difficult to believe that the filter was causing issues with the roll over/out events. I will expand on the example code you provided so you get an idea of what I am trying to accomplish and where my issues arise.
EDIT: I should add that the issue is only present when I tween AND add a filter. If I only add a filter or if I only tween I have no issues but the combination or adding a filter and tweening causes the OVER/OUT events to fire rapidly.
//This code does not result in a flashing animation
myClip.addEventListener(MouseEvent.ROLL_OVER, overClip);
myClip.addEventListener(MouseEvent.ROLL_OUT, outClip);
function overClip(e:MouseEvent):void
   myTween = new Tween(myClip, "scaleX", Regular.easeOut, myClip.scaleX, 1.5 , 3, true);
   myTween = new Tween(myClip, "scaleY", Regular.easeOut, myClip.scaleY, 1.5 , 3, true);
function outClip(e:MouseEvent):void
   myTween = new Tween(myClip, "scaleX", Regular.easeOut, myClip.scaleX, 1 , 3, true);
   myTween = new Tween(myClip, "scaleY", Regular.easeOut, myClip.scaleY, 1 , 3, true);
//However if i add these lines of code to add and remove a filter I can observe the flashing effect when the mouse is near the edge of the moveclip
myClip.addEventListener(MouseEvent.ROLL_OVER, overClip);
myClip.addEventListener(MouseEvent.ROLL_OUT, outClip);
function overClip(e:MouseEvent):void
   myClip.filters = [myDropShadowFilter];
   myTween = new Tween(myClip, "scaleX", Regular.easeOut, myClip.scaleX, 1.5 , 3, true);
   myTween = new Tween(myClip, "scaleY", Regular.easeOut, myClip.scaleY, 1.5 , 3, true);
function outClip(e:MouseEvent):void
   myClip.filters = [];
   myTween = new Tween(myClip, "scaleX", Regular.easeOut, myClip.scaleX, 1 , 3, true);
   myTween = new Tween(myClip, "scaleY", Regular.easeOut, myClip.scaleY, 1 , 3, true);
Is there something obviously wrong with this approach to adding a filter/tweening? I am fairly new to flash.
Thanks again!
Message was edited by: Dafunkz

Reader causing issues with dropped underscores in courier new font

When converting a microsoft word document in 2013 or 2007 to a PDF is causing issues with dropped underscores. It only seems to happen in courier new. For instance if I have _someCode, when converting this over to a PDF file I will sometimes see _someCode and sometimes I will see someCode. If I open this file in a different pdf reader then it looks correct 100% of the time. If I copy and paste into another application then the underscore shows. This is a major issue for people putting code into a PDF document as underscores are important and courier new is what we often use.

I love how quick you are to throw Microsoft under the bus. Often it is their fault. In this case I believe you are 100% wrong and absolutely short sighted to ignore this. As I said in my original email, which you apparently missed, I have tried this in multiple PDF viewers and Adobe Reader is the ONLY reader that misses the underscores. Foxit, PDF Exchange and Sumatra all render it perfectly. Adobe reader missed 6 underscores in my document that has 18 underscores. 30% of the time in this document Adobe Reader makes the underscore invisible. And if I switch the zoom to 100% instead of 148% (which is the default for me for some reason) then Adobe Reader misses 7 of them. This doesnt occur in the other readers. Blame Microsoft all you want but the simple fact is that Adobe Reader has issues reading courier new's underscores. It needs to be fixed.

I have a 2012 Macbook Pro and the GPU is causing issues with Yosemite. How can I resolve this issue?

I have a 2012 Macbook Pro and the GPU is causing issues with Yosemite. There are a number of issues I have run across:
If I have four tabs open on Safari then I start to get a flickering on the screen from the GPU refreshing
When I leave the computer alone for more than 20 mins the screen saver should start -- what happens is that the screen goes to black. When I move the cursor I do not get the login screen. I have to reboot
FireFox Web browser will not run
I get issues with the computer running very slowly
I have already turned off the transparency option in settings. Any ideas??
Cheers
Matt
MacBook Pro, OS X Yosemite (10.10), GPU / Video Card with Yosemite

Do you have more than one OS on the Mac?
You may want to look at something like http://bjango.com/mac/istatmenus/. This has a Free Trial window, but it is a commercial application. If there are any heat/sensor issues, this may help.
A SMC Reset or PRAM/NVRAM reset may also help.
Intel-based Macs: Resetting the System Management Controller (SMC) - Apple Support
Startup key combinations for Intel-based Macs - Apple Support

Strange issue with iWeb site, please help

Hi everyone,
Until recently, I've been keeping an iWeb blog of my time in India. Nothing too complicated, just stories and photo albums. However, recently something strange has happened, and the website is no longer displaying correctly. It looks fine in iWeb, and when I publish it in a folder and open it locally, everything is fine. However, after uploading it to my hosting provider, it looks like this:
http://www.egbertopreis.nl/India/
(screenshot of what it looks like here: http://egbertopreis.nl/website_screenshot.PNG )
This is a screenshot from iWeb of what it should look like: http://www.egbertopreis.nl/iWeb_screenshot.png
I'm using the 'darkroom' theme, but as you can see, something is clearly wrong. It is not displaying the menu correctly, the layout looks strange and it isn't loading any of the articles. The other pages are accessible if you navigate there directly, but there you have the same problem.
It looks like, for some reason, the CSS and javascript elements cannot be loaded, although I have no idea why this might be the case. They are all just static files, and it worked fine until about a week ago.
Although I'm an IT professional, I have literally no idea what could cause a problem like this. I went with iWeb because I wanted to use an 'easy' solution and not over-engineer something for once
Usually what I'd do in a situation like this, is just purge the whole site and re-upload it. However, since I'm traveling around, I don't have fast internet access anywhere and the site is now so large that it would take forever to completely re-upload. This is also the reason why I can't troubleshoot it properly myself...
Any help (or even words of encouragement :-)) whatsoever would be extremely welcome. Thanks in advance!
Message was edited by: Heliode
Edit: Forgot to mention what I already tried myself;
- deleted the HTML and XML files and let iWeb do 'publish changes'. Everything was re-uploadeded, but issue remained.
- Deleted the 'Scripts' folder on the remote host, and manually re-uploaded from locally published folder. No effect.
- Tried randomly changing layout items in the hope that any potentially corrupted files might be overwritten after publishing. No effect.

Hi Roddy, thanks for your reply. It wasn't just me though; a lot of other people from back also reported the same issue. I was also getting the same thing from behind a wired connection. You can still see and experience the issue yourself if you look here.
I've since 'resolved' the issue by getting a .Mac trial account. A friend helped me move the whole blog over there, where the site works as it is supposed to:
http://web.me.com/eggmeister/India/
Therefore the issue has to be with the hosting. Right now I'm suspecting it might be some obscure configuration issue with the hosting company's server. Maybe something like too low a setting for Apache's 'MAX REQUESTS'. This might cause issues with all the javascript going on in the iWeb pages, loading elements back and forth. I'm in contact with the hosting provider, and will let you know what I find. Might be useful for future reference.

IE issue with iWeb site

1) Images don't load
2) in IE 8 : HTML email snippet does not show up
How can this be resolved?

Hi Roddy, thanks for your reply. It wasn't just me though; a lot of other people from back also reported the same issue. I was also getting the same thing from behind a wired connection. You can still see and experience the issue yourself if you look here.
I've since 'resolved' the issue by getting a .Mac trial account. A friend helped me move the whole blog over there, where the site works as it is supposed to:
http://web.me.com/eggmeister/India/
Therefore the issue has to be with the hosting. Right now I'm suspecting it might be some obscure configuration issue with the hosting company's server. Maybe something like too low a setting for Apache's 'MAX REQUESTS'. This might cause issues with all the javascript going on in the iWeb pages, loading elements back and forth. I'm in contact with the hosting provider, and will let you know what I find. Might be useful for future reference.

Uk date format issue with ASP and Access Database

I have an Asp form which updates records in an Access
database. Problem is
that the date format in the database record is dd/mm/yyyy
(UK), when
the record is displayed on the form it is mm/dd/yyyy(US)
which after I
update the record in the database the date has changed to the
new format.
I have tried everything I can to change the format but to no
avail...anyone any ideas how I can resolve this issue?
Thanks
Steve

stevo.s wrote:
> Hi
>
> I have tried changing the format on the date field on
the server behaviours
> panelto ddmmyyy. Also have tried to set the form field
format to ddmmyy. I have
> also tried to use a function I got from a posting
somehwere on the net to no
> avail. <%function ddmmyyyy(varDate)
> ddmmyyyy = Day(DateValue(varDate)) & "/" &
Month(DateValue(varDate))
> & "/" & Year(DateValue(varDate))
> end function
>
> I believe that this is a recognised issue with
Dreamweaver and Access but
> can't seem to grasp the work around! Problem being I am
teaching myself through
> books and internet articles and can be weeks at a time
without being able to
> look at the issue..each time I come back to it it is
like starting all over
> again! I was hoping that somewhere out there there is a
simple solution the
> issue perhaps a date picker with the built in
functionality to address the
> issue...I am keen to understand how to deal with the
issue rather than just
> change my database date field to fudge the problem as I
am in the UK and when I
> eventually start to use the application I would like
there to be some
> consistency with dates and that users are familiar with
the format.
>
> Any help gratefully received!
Its not Dreamweaver, or Access, its your servers locale, its
set to US
format, not the UK.
On your page at the top use:
<% Session.LCID = 2057 %>
This will force the page into using UK formatted dates. Use
it on any
page that needs to format the page correctly.
Dooza
Posting Guidelines
http://www.adobe.com/support/forums/guidelines.html
How To Ask Smart Questions
http://www.catb.org/esr/faqs/smart-questions.html

Pre-n enabler seems to cause issues with lock up/beach ball

I just received my new C2D MBP yesterday with 3G of RAM and all was peachy. I decided to install the $1.99 Pre-N enabler patch from Apple and it appears that I'm not alone in having that cause system lock ups and beach balls from ****.
I unfortunately seem to be in the same boat. It runs for awhile and then all of a sudden it will just lock up and I'll get the spinning beach ball from **** forever, until I reboot.
I'm using mine with a NetGear Pre-N wireless router and while I'm getting 140kpbs connections I am getting a lot of receive errors and the machine just goes off to la-la land.
I was worried about something else until I read these posts over in Internet & Networking and now I'm wondering if there really is an issue with whatever the "enabler" did. It ceratinly appears to be this. Nothing else seems to cause it this kind of beach ball death.
So now I guess we need to look for an "un-enabler" patch. Just out of curiosity where do we email problems like this to get resolved?
UGGHHHHHHH!!!
Peter

I have this same problem. I reported a bug to apple bug id#4990056
Here is what i wrote:
10-Feb-2007 10:36 PM Brooks Roy:
Summary:
I recently got a Linksys WRT350N 802.11n router and using it with my macbook pro core 2 duo. The router is firmware version 1.03.2.
After installing the enabler from the apple site i verified it upgraded properly and it shows a/b/g/n for my airport card. However the computer has been locking up more and more. I finally narrowed it down to the airport card. Here is what happens:
Steps to Reproduce:
With regular airport usage, the mac will all of the sudden give the spinning 'beach ball' and just sit there. A simple http download will stop and the mac will become unresponsive. I cannot launch new applications. The icons will bounce in the dock but never open. I cannot force-quit any applications. My only option is to hold down the power button for a hard shutdown.
I can almost duplicate the issue 7 times out of 10. Sometimes it takes 15 minutes or so before it locks up, sometimes its almost immediately.
I have done a full fsck and permissions. I also downloaded tiger cache cleaner and cleaned all settings. I have also booted off the apple install cd and done a extended full RAM check on the 2Gb installed in my computer.
I have restored my IO80211Family.kext from my other macbook pro (regular core duo) and my problems have gone away. I am 100% sure there is a bug with the 802.11n enabler and the Linksys WRT350N.
I do not have any special configuration on my linksys, just MAC based wireless authentication.
When using the MacBook pro on the WRT350N in 802.11g without the latest 802.11n enabler the mac performs fine and does not become unresponsive.
Expected Results:
I expect the mac to perform just as a 802.11g network will work with increased transfer speeds.
Actual Results:
See above.
Regression:
It only occurs when using network traffic (i.e Mail.app, Safari browsing sites, etc. Any application that requires Airport.
Notes:
I am using the original IO80211Family.kext driver that does not have 802.11n support and it works properly. Also using builtin ethernet with airport off and the 802.11n driver works (obviously).

8.3 causing issues with safari, "Safari could not open the page because server stopped responding"

Since my upgrade to 8.3 there are several issues with many apps when they are trying to download information.
When I go to Safari and open i.e. msn.com. it tries for over 60 seconds. then I get the error:
Safari could not open the page because server stopped responding.
I have a iPhone 6 plus with 113 gig and 65 gig available
This same issue is causing problems when downloading articles on facebook and instagram app.
We also noticed this same issue on Macbook Air, and iMac, iPad 2, and iPhone 5s.
I also have the Mac Pro without these issues but it is connected by ethernet instead of wireless.
Is wifried back and now plaguing all devices?
I selected mac because, I was tried of all the PC issues with new updates. It seems mac is now lowering its quality to that of PC.
We need a fix for this ASAP!

I have tried resetting my Iphone 6 Plus by holding both the off and select buttom. This did not help.

Mountain Lion Upgrade causing issues due to hard drive fault

I have a question about Mountain Lion crashing your hard drive. I upgraded my Macbook Pro 13' several weeks ago afer the release of Mountain Lion. The download took sometime before it completed it's download and completed without incident. Since that time I've had no issues with the softward update, my hard drive or computer.
However yesterday evening I went to use my computer and the screen after the Apple logo disappeared showed a circle w/a line thru it and turning gears just below it. After reading several forums and posts it seems that the computer cannot find a bootable disk to load up from. I do not understand this as I not changed the HD and the computer was working fine just the day before.
I tried to do a reinstall of the original OSX system (snow leopard) - it did download but after the computer re-started the system went back to the same screen w/the circle and line thru it. I then restarted computed hitting options to take me into the recovery / disk utility. From their I tried to verify and repair the HD - still same problem (circle w/line), I then just tried to reinstall Mountain Lion (same results).
WTH is going on - this was a perfectly good computer working fine & now I cannot get it to boot up or run at all? Could this be a software issue due to Mountain Lion or simply a bad HD? Any advice on how best to correct this issue would be appreciated. I use my laptop for dj'ing and have an upcoming gig in 2 weeks. HELP...

Heres the problem im having maybe it is similer
System MAC Book Pro Mid 2012 Dule hard drives 150 GB SSHD 500 GB in alternate slot
Updated Firm ware
Computer booted successfully
entered password computer reacted normaly color adjusted for my user settings
computer beeps repeatedly untill forsed shut down
reinstalled Lion worked fine again
updated to mountan lion
computer atempts to boot from the SSHD and fails
Boots to system diagnostics primary hard drive is invisable to the system
waited about a week
booted my system (at a new location)
Primary hard drive reapeared
Boots to system diagnostics
reinstalled Lion worked fine againupgraded to mountan lion again to test a theory
computer atempts to boot from the SSHD after instalation and fails
Boots to system diagnostics primary hard drive is invisable to the system
So its Back to Square one any thoughts coments or general advice?
- Thanks

PI 7.1 upgrade related issue (With removeContexts node function)

Hi all,
We have upgrade from PI 7.0 to 7.1, there was no changes done to the maps...but when we execute the old maps it give no value in the queue error: (this occurs during run time)...
But when I test the payload it executes fine...I have found and issue with remove context (the queue display in 7.0 is different than in 7.1)
It doesn't end with SUPPRESS context change...we have observe that the maps which has removeContext are failing...
Is there any OSS note on this issue...anyone faced this issue?
Any suggestions?
Thanks,
Srini
Edited by: Srinivas Davuluri on Oct 2, 2009 6:55 PM

I have added the parameter to the init method of the Functions tab in our message mapping - retainlastValueofPreviousContext=true; according to the blog...but still the same error...
But, when I execute in the Test tab it works fine;
Any other suggestions or anyone who has faced this issue...we are on PI 7.1 SPS7
Thanks,
Srini
Edited by: Srinivas Davuluri on Oct 5, 2009 9:46 AM

WAAS 4.1.1c Upgrade causing issues with intranet site access

Similar Messages

Maybe you are looking for