WAAS Central Manager - Procedure for changing FQDN and ip address

Software version 4.1.1c
I have the need to change my waas central manager hostname, doamin name and ip settings. What is the proper procedure to do this in order to keep the cm synchronized with the waes. I seem to have them out of sync now. Do you deregister all the waes first, change and reboot the cm, then register them again?

Hi,
check SAP note 8307 Changing host name on R/3 host: What do you do?

Similar Messages

Is WAAS Central Manager needed for SRE?

Hello experts,
We're planning to deploy just WAAS SRE in 3945 routers at multiple sites? Do we need to buy WAAS central manager? also can WAAS SRE be configured from command line and able to save the config to text file just like on router's IOS?
Thanks

Hi,
For your setup to be supported, you need to have all of your WAAS devices registered to a Central Manager.
Will it optimise connections if you don't? Yes it will but if you run into any issues with it, you will be on your own...
Regarding the configuration, you need to have the module imported into a CM but you can do all of the config from the CLI if you prefer and only use the CM for statistical reporting.
Nicolas

Using Jackrabbit User Manager programmatically for changing passwords and getting user data.

I am trying to do a change password request using the Jackrabbit User Manager with the REST URL /system/userManager/user/<username>.changePassword.json. The problem I am having is that this request requires an oldPwd form param in the request. The issue is that when I am trying to do this request it is in response to the user selecting "Forgot Password" so our logic has created a random password which we then email to the user so they can use that the next time they want to login. We need to change that user's password in CRX so they can log in using it next time. Since they haven't logged in there is no session, NOT the problem. THE PROBLEMS, I don't know 1. how to use the userManager to get that user's old password, since /system/userManager/user/<username>.json doesn't appear to return the password and 2. if I could get the old password it most certainly will be encoded, some how, so I will need some decoding algorithm to pass it through in order to get the actual password to set as the oldPwd form param to my change password request. Please let me know if you require any further explanation. Any assistance would be greatly appreciated. Thank you, in advance, for your assistance.
Sincerely,
Mike Sucena
[email protected]

Hi Mike,
msucena wrote:
Justin:
Does your response mean that until version 2.1.2 of Jackrabbit User Manager is released I cannot change the password without knowing the old password?
No. It means that this feature is not available in version 2.1.0 of the Sling Jackrabbit User Manager bundle. It was added after that release. You have a number of options:
Build the bundle from source.
Use one of the SNAPSHOT bundles available from the Apache Snapshots repository.
Use the release which is being voted upon now (https://repository.apache.org/content/repositories/orgapachesling-175/org/apache/sling/org .apache.sling.jcr.jackrabbit.usermanager/2.2.0/). (Note - we decided to use 2.2.0 as the version number rather than 2.1.2 as originally planned due to the scope of this release).
Write a different servlet which performs the same actions.
Meaning that being able to use either the credentials of the "Admin" user or using the credentials of a member of the "UserAdmin" group is not supported in the current released version 2.1.0?
Correct. It was added after the 2.1.0 release.
If I currently need the old password is there any Sling REST - Jackrabbit API call I can use in order to get the old password since using /system/userManager/user/<username>.json doesn't appear to return the password?
-Mike
The plain text password is not stored. And this should be considered a good thing.
If you have questions about the development process we follow in Sling (or at Apache as a whole), by all means ask on the Sling users mailing list. It is reasonably well-established and we love to talk about it.

Advice for WAAS Central Manager?

Hello,
We are building a WAAS lab (not production) for a customer and we recently discovered that we can't use the NME-WAE-502-K9 as the central manager which was very affordable. So we are very disappointed about this. The other equipment are Cisco ISR 2811 (very affordable for building WAAS) with NME-WAE-502-K9 running WAAS 4.1.1 acting as the application accelerators. I have some questions and asking for some advice about some alternative options for us to consider:
What is the cheapest/smallest WAAS option we can use for the WAAS central manager? The only thing I could find is the WAE-512-K9, but maybe there is something else that is smaller and cheaper for consideration.
From what I read, after WAAS software version 4.1.1 it requires the Enterprise and Transport Licencing. Does the WAAS central manager have a 30,60, or 90 day trial that the CM can run before a license is required like most of the Cisco Unified Communications products today?
Thanks in advanced!
-rya

A central manager is required to managed all of your accelerators properly in a supported configuration. You don't necessarily need a physical appliance though. There is also the virtual form factor (vWAAS is the accelerator version and vCM is the manager version) that can run on a ESXi hypervisor.
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/vwaas/guide/vwaasguide.html#wp69212
John
If this is useful please mark as Helpful or Solved.

Renewing Self Signed Certificate for WAAS Central Manager

Hi,
We would like some help from you about the following: We have an WAAS Central Manager which its self-signed certificate validity has expired as showed below:
Validity
Not Before: Jul 7 00:47:06 2009 GMT
Not After : Jul 6 00:47:06 2014 GMT
We have used its certificate to install some other remote WAAS Express routers.
We would like to know the following:
1. is it possible to renew this certificate? or
2. do we need to reinstall another certificate on CM and replicate this new one on these waas express remote devices?
If affirmative for at least one of them, please, could you share any document that describe how to do it?
I have attached some output commands from our CM.
Thanks,
Marcelo

attaching file now!!!

Https certificate on WAAS Central Manager

Hi,
I wanting to know if it is possible to authenticate the WAAS central manager with a different certificate/key pair than the self-signed certificate/key pair.
I can't find any information about installing my own certificate/key pair.
Thanks in advance

We do have an option for the same:
First you may generate a CSR using:
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v531/command/reference/execmds.html#wp2773266
Once done you can get the cert and import cert and keys on Central Manager using admin option
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v531/command/reference/execmds.html#wp2773369
"admin"
Specifies that the certificate and key are for the Central Manager admin service. This option can be used only on the Central Manager.
The Central Manager admin service uses a self-signed certificate and key by default. You can use the crypto import pkcs12 admin command to import a custom certificate and key in PKCS12 or PEM format. If you delete the custom certificate and key, the self-signed certificate and key again become active.
Hope this helps,
Swati

WAAS Central Manager Replacement

I have need to replace a WAAS Central Manager (4.4.x). The replacement would have a new IP address. The planned path of migrating is first to setup the replacement as standby and once sync'ed promote to primary. I will then manually update the WAE devices with new IP address.
OLD CM:
WAE# configure
WAE(config)# central-manager role primary
WAE(config)# cms enable
On the standby device, execute the following CLI commands:
WAE# configure
WAE(config)# central-manager role standby
WAE(config)# central-manager address new IP
WAE(config)# cms enable
Is this idea the best approach?
Any idea if the SSL certificates would have to be revoked and re-issued (whether self signed or otherwise)?

Hi,
The steps to replace a CM hardware have been documented under the following bug:
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtz47138
Basically, the steps are the following:
If the CM will be using the same hardware and IP you can restore the CMS database.
If the CM will be using a new name or IP, use the workaround provided by CSCsi59886:
1- Add new CM as standby
2- Make it primary
3- deactivate former CM in new CM GUI
4- delete former CM from new CM GUI (and make sure it s gone from the DB)
5- 'cms deregister' on former CM CLI
7- rename former CM, change its mode and reload.
8- rename the new primary and change its IP address
9- Change the IP and mode of former CM and register it
Regards,
Nicolas

Cisco WAAS Central Manager

Can someone tell me how to deploy Cisco WAAS Central Manager to manage 100 WAE devices over WAN? Is there any additional devices need to setup redundant design and any license cost included here per device basis to monitor? I need detailed solution to manage WAE devices centrally.

Vinod,
There is no need to buy additional licenses or no need to add per device license on the central manager. You can go with the 294-4G or the 474 device , these can support upto 250 devices. However would suggest you to go with a higher model so in future if you expand , you might want to replace the CM that time.
Also a central manager cannot work as a inline or wccp device nor it can do any optimization.
Regards
Abijith

Hi! I've been using Goldmine contact management software for many years and syncing with Companion Link successfully, then ITunes to the IPhone. Suddenly, my IPhone is not recognized and won't sync. I see a message telling me to dock the phone? Any ideas?

Hi! I've been using Goldmine contact management software for many years and syncing with Companion Link successfully, then ITunes to the IPhone. Suddenly, my IPhone is not recognized and won't sync. I see a message telling me to dock the phone? Any ideas? Thanks for any assist!

Hi Ken,
Dennis here from westport. I too am a goldmine user for many years and would love to know how you sync.
I am looking at a product called wmobile, but may be problematic on my current system.
thanks for any help...

Procedure for CICS adapter and XI integration?

Dear All,
Can you plz provide me the step by step procedure for CICS adapter and XI integration?
Thanks,
Srinivas.

Hi ,
Check this link..
http://www.iwaysoftware.com/products/adapters/CICS_IMS_Transaction_Processing.html
Regards,

HT1051 Trying to change Shipping and Delivery address for one in the US, from Canada, and can't do it. State and zip code appears in red but no change in country name. Using French (Canada) iPhoto app.

Trying to change Shipping and Delivery address for one in the US, from Canada, and can't do it. State and zip code appears in red but no change in country name. Using French (Canada) iPhoto app.

Larry's right, You can still use your credit card, you just need to change the "billing address" to the recievers address. It gets billed to your CC and delivered to the US

RE: 1) Changing name and IP address of an AIX 4.2 Server 2)Using NAT

Daniel,
you (normaly) just have to :
1) edit the $FORTE_ROOT/fortedef.sh fileand change the value of variable
FORTE_NS_ADDRESS
2) shutdown and restart forte environment
3) put the new values in the control panel of the client and run !
It worked on our site with the same configuration (Aix 4.2)
Good luck
De : Daniel[SMTP:[email protected]]
Répondre à : Daniel
Date : vendredi 18 juin 1999 13:08
A : [email protected]
Cc : Jose Ignacio
Objet : 1) Changing name and IP address of an AIX 4.2 Server 2)
Using NAT to reach forte
Hello Forte Users :
    I have 2 questions to make:
    1)
    I've installed a Forte Server Central Node (Release 3.0.F.2) in an
IBM RS/6000 with OS AIX 4.2
    (The name of the server is Name_1 and the IP address is
125.125.50.50 with mask 255.255.255.0)
    Nowadays we had to change the name and IP address of this server
lets say to Name_2 and 125.125.60.60 with mask 255.255.255.0.
    After that we try to find any reference to old name and IP address
in the forte directory and all of its subdirectories changing them to
the new ones.
    After these changes we found than forte could'nt start the nodemgr
server.
    We have too many reasons to avoid installing FORTE again.
    Does anybody know if I have to change anything more to make
nodemgr server work.
    2)
    The second question is about NAT (Network Address Translation).
    To reach a Forte Server Central Node from a Forte Client we have
to pass through a Firewall and NAT.
    We are researching and at this moment we can not reach the server
from the client, has anybody any suggestion to correctly configure
Forte (Client and Server) to use NAT between them.
    If anyone could help me I would be very pleased.
    Thank you very much in advance,
    Daniel GonzáLucas (EAM Sistemas Informáticos SL, Spain,
e-mail: [email protected])
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>

>> 15 Mins is not enough for completely the replication.
>> use repadmin /syncall /aEpd   - for force replication.
>> Wait 3 hrs minimum.
Regards,
Biswajit
MCTS, MCP 2003,MCSA 2003, MCSA:M 2003, CCNA, Enterprise Admin, ITIL F 2011
Blog:
Script Gallary:
LinkedIn:
Note: Disclaimer: This posting is provided & with no warranties or guarantees and confers no rights..

I do not receive verification email for changing my iCloud email address

i would like to change my iCloud email address e.g. change from: [email protected], to: [email protected]
I do not receive verification email for changing my iCloud email address, even though it says verification email sent.
I also tried the "forgot apple ID" option to change it that way, i received an email but it was for resetting my password.
is there anyway i can change it?

Hello, skengzz.
Thank you for visiting Apple Support Communities.
I see you are experiencing an issue receiving the verification email. Here are a couple articles that will help you with this. Make sure to also check your junk folder on your mail account for this email.
If you didn't receive your Apple ID verification or reset email
http://support.apple.com/kb/TS5404
Apple ID: Contacting Apple for help with your Apple ID
http://support.apple.com/kb/HT5699
Cheers,
Jason H.

Can I create a report at WAAS central manager based on server IP address

Hi,
I have two distinct applications running at port 8080 for which I would like to have separated performance reports at Central Manager. Is there any mean to do that by using server ip address for example? If so how? Do I need to change policy? If so is that the only way?
Thanks
Wilhelm

Hi Rulix,
The latest version of CR Server is 2008. Therefore I'm assuming you are using CR Server 2008.
New in CR 2008 is the .NET report modification software development kit (SDK). The report application server (RAS) SDK is now available for users of Crystal Reports .NET API without the use of a RAS server. Report modification such as changing, adding, or removing database providers, or adding, removing, or creating report objects, parameters, formulas, and sections can be achieved by accessing the RAS SDK through the Crystal Reports .NET SDK.
Java developers however receive the JRC and Java SDK documentation through the free Crystal Reports for Eclipse download. This product will be updated on a separate schedule from Crystal Reports.
Further Information and samples are available in our [Developer Library|https://www.sdn.sap.com/irj/sdn/businessobjects?rid=/webcontent/uuid/5001d5de-f867-2b10-00bf-8d27683c85a0]
Kind regards,
Tim

WAAS Central Manager version 4.1

Hello,
I have to prepare a design of a WAAS deployment for my customer. I have an issue with the 4.1 version: Does i have to use an appliance dedicated for the management or i can use an WAE-512 with entreprise licence for managament and for WAN optimization features?
Thank you in advance

In any version of WAAS the supported configuration is to have a minimum of 2 application accelerators and one central manager. You cannot run the Central Manager and Application Accelerator on the same device.
The enterprise license unlocks specific features, notably CIFS acceleration but will not influence the number of required WAE's.

WAAS Central Manager - Procedure for changing FQDN and ip address

Similar Messages

Maybe you are looking for