Waas configuration with NME

I have a branch deployed with an appliance using WCCP and I just purchased a module for a smaller site. I am having trouble equating wccp config over to the module. Read all the white papers but I am missing something really simple.
I will apreciate to help me about this issue, I have two week with the same issue.
I send the configuration the remote BRANCH and the topology..
I wait for your coments , specially with the words marks.
ip wccp 61 redirect-list CRONOS
ip wccp 62
interface Loopback1
description Loopback BGP
ip address 192.168.249.8 255.255.255.255
interface GigabitEthernet0/0
description Interface LAN
ip address 192.168.161.4 255.255.255.0
no ip proxy-arp
ip accounting output-packets
ip wccp 61 redirect in
ip wccp 62 redirect out
ip route-cache flow
duplex auto
speed auto
standby 1 ip
standby 1 priority 220
standby 1 preempt
service-policy input LAN-PANA2-MARQ
service-policy output WAN-PANA2-QOS
interface GigabitEthernet0/1
description ENLACE TLC_ASB_50
ip address 192.168.167.13 255.255.255.252
no ip proxy-arp
duplex auto
speed auto
service-policy input LAN-PANA2-MARQ
interface Serial0/0/0
description Enlace a PERU
bandwidth 2048
ip address 192.168.114.9 255.255.255.252
ip accounting output-packets
ip wccp 61 redirect in
ip wccp 62 redirect in
ip flow ingress
ip flow egress
encapsulation ppp
load-interval 30
shutdown
interface Serial0/0/1
no ip address
shutdown
clock rate 2000000
interface Integrated-Service-Engine1/0
ip address 192.168.165.129 255.255.255.128
ip wccp redirect exclude in
service-module ip address 192.168.165.140 255.255.255.128
service-module ip default-gateway 192.168.165.129
no keepalive
router eigrp 12
redistribute static
redistribute bgp 250 metric 10000000 1 255 255 1500
network 192.168.161.0
network 192.168.167.12 0.0.0.3
network 192.168.249.0
no auto-summary
ip flow-cache timeout active 1
ip flow-export source Loopback1
ip flow-export version 9
ip flow-export destination 130.1.8.30 2055
p access-list extended CRONOS
permit ip host 192.168.161.13 192.168.112.0 0.0.0.255
permit ip host 192.168.161.16 192.168.112.0 0.0.0.255
permit ip host 192.168.161.23 192.168.112.0 0.0.0.255
permit ip host 192.168.161.91 192.168.112.0 0.0.0.255
permit ip host 192.168.161.71 192.168.112.0 0.0.0.255
permit ip host 192.168.161.72 192.168.112.0 0.0.0.255
permit ip host 192.168.161.76 192.168.112.0 0.0.0.255
permit ip host 192.168.161.77 192.168.112.0 0.0.0.255!
Regards,

Daniel,
I send a topology, for your opinio and best practice the how configurate the WAAS in WCCP.
I hope your help for this issue,
It posible to configure this command in the router WAN (ip wccp 62 redirect in) and the router WAAS ((ip wccp 62 redirect out , (ip wccp 61 redirect in)?.
Or I need more commands for this configuration.
Yesterday I sent the configuration the R1, today I send you agein.
ip wccp 61 redirect-list CRONOS
ip wccp 62
interface Loopback1
description Loopback BGP
ip address 192.168.249.8 255.255.255.255
interface GigabitEthernet0/0
description Interface LAN
ip address 192.168.161.4 255.255.255.0
no ip proxy-arp
ip accounting output-packets
ip wccp 61 redirect in
ip wccp 62 redirect out
ip route-cache flow
duplex auto
speed auto
standby 1 ip
standby 1 priority 220
standby 1 preempt
service-policy input LAN-PANA2-MARQ
service-policy output WAN-PANA2-QOS
interface GigabitEthernet0/1
description ENLACE TLC_ASB_50
ip address 192.168.167.13 255.255.255.252
no ip proxy-arp
duplex auto
speed auto
service-policy input LAN-PANA2-MARQ
interface Serial0/0/0
description Enlace a PERU
bandwidth 2048
ip address 192.168.114.9 255.255.255.252
ip accounting output-packets
ip wccp 61 redirect in
ip wccp 62 redirect in
ip flow ingress
ip flow egress
encapsulation ppp
load-interval 30
shutdown
interface Serial0/0/1
no ip address
shutdown
clock rate 2000000
interface Integrated-Service-Engine1/0
ip address 192.168.165.129 255.255.255.128
ip wccp redirect exclude in
service-module ip address 192.168.165.140 255.255.255.128
service-module ip default-gateway 192.168.165.129
no keepalive
I wait your answers,
Thanks
Best Regards,

Similar Messages

Sample configuration of IME 7.0 with NME-IPS-K9 and How to get licence for NME-IPS-K9?

Dear all,
I already installed NME-IPS-K9 with Cisco Router 2821 series successfully and I used IME(Cisco IPS Manager Express 7.0.1) to configure NME-IPS-K9 but I never try with this before. I have some issue need everyone help:
1. Could you share the sameple for configuring IME with NME-IPS-K9 to monitor and manage all network traffice or package that attack to NME-IPS-K9?
2. Could you show me how to get licence for NME-IPS-K9?
Thanks everyone for your time to help me and share your great ideas.
I am really appreciated and looking for forward to hearing response from you all.
With my warm regards,
Sarem Phy
H/P:092562530

CPU 100% on the NME-IPS module is normal. It will always show 100%. CPU on IPS is not related to the inspection load.
To check if the IPS module is overloaded, please check the "Inspection Load" speedometer.

WAAS Configuration for 3750 Switch

I am configuring a 3750 switch with 12.2(52)SE according to:
(from https://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/12.2_52_se/configuration/guide/3750_scg.pdf )
This example shows how to configure SVIs and how to enable the web cache service with a multicast group list. VLAN 299 is created and configured with an IP address of 175.20.20.10. Gigabit Ethernet port 1 is connected through the Internet to the web server and is configured as an access port in VLAN 299. VLAN 300 is created and configured with an IP address of 172.20.10.30. Gigabit Ethernet port 2 is connected to the application engine and is configured as an access port in VLAN 300. VLAN 301 is created and configured with an IP address of 175.20.30.50. Fast Ethernet ports 3 to 6, which are connected to the clients, are configured as access ports in VLAN 301. The switch redirects packets received from the client interfaces to the application engine.
Note Only permit ACL entries are being used in the redirect-list; deny entries are unsupported.
Switch# configure terminal
Switch(config)# ip wccp web-cache 80 group-list 15
Switch(config)# access-list 15 permit host 171.69.198.102
Switch(config)# access-list 15 permit host 171.69.198.104
Switch(config)# access-list 15 permit host 171.69.198.106
Switch(config)# vlan 299 WEB SERVER
Switch(config-vlan)# exit
Switch(config)# interface vlan 299
Switch(config-if)# ip address 175.20.20.10 255.255.255.0
Switch(config-if)# exit
Switch(config)# interface gigabitethernet1/0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 299
Switch(config)# vlan 300 WAE
Switch(config-vlan)# exit
Switch(config)# interface vlan 300
Switch(config-if)# ip address 171.69.198.100 255.255.255.0
Switch(config-if)# exit
Switch(config)# interface gigabitethernet1/0/2
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 300
Switch(config-if)# exit
Switch(config)# vlan 301 CLIENTS
Switch(config-vlan)# exit
Switch(config)# interface vlan 301
Switch(config-if)# ip address 175.20.30.20 255.255.255.0
Switch(config-if)# ip wccp web-cache redirect in
Switch(config-if)# exit
Switch(config)# interface gigabitethernet1/0/3 - 6
Switch(config-if-range)# switchport mode access
Switch(config-if-range)# switchport access vlan 301
Switch(config-if-range)# exit
===================================================================
Question: How do I configure my WAE to play nicely with this switch?

Hi James,
Here is the link to WCCP config part on WAE:
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v441/configuration/guide/traffic.html#wp1041742
In your case, if my understanding is right, VLAN300 is where you want to connect WAE and WAE is also L2 adjacent. if that is true, here is the config you need on WAE:
wccp router-list 1 171.69.198.100
wccp tcp-promiscuous router-list-num 1 l2-redirect mask-assign l2-return
wccp version 2
Please note that 3750 supports L2 redirection only with redirect IN statements on 3750 interfaces connected to servers and clients.
Hope this helps.
Regards.

I changed my sim on my iPhone n reconfigured iMessage, it configured with my number but when i sign in with my apple id it says username/password is wrong while in all other things like FaceTime, App Store it worked with the same id and password

i changed my sim on my iPhone n reconfigured iMessage, it configured with my number but when i sign in with my apple id it says username/password is wrong while in all other things like FaceTime, App Store it worked with the same id and password..
can anyone help me to solve this issue

i just opened my ipad, started my apple account/I.D. and realized I put the wrong e mail. I was having trouble correcting my I.D on the Ipad so I went to my laptop and make the proper changes/slash e mail address I wanted for my apple ID. I got back to my ipad and try to download an app I can't because I have to sign in my apple account and I can't because it still has the irrelivant I.D/email address..
So, i did what you said.. went to setting>app store> tapped on my e mail.. it asked me to sign in (with my invalid emails address showing). I signed in with the password I had created. It said "incorrect".. I went to reset password. I reset password, tried to sign in and it says again "unvalid password".. this is getting irritating. I have been asking and no one knows what to do.

I have a problem with Mail on my Macbook Pro. It is configurated with a gmail account, and now I can't access the mail. Is it possible to reboot the account or..? Please help:)

I have a problem with Mail on my Macbook Pro. It is configurated with a gmail account, and now I can't access the mail. Is it possible to reboot the account or..? Please help:)

The question mark means the computer cannot find a bootable volumes so can;t do anything, That, combined with annoying sounds, strongly suggests a failed hard drive.
You can ask a "genius" at an Apple Rtail Store to test it but I'm pretty sure the drive is kaput. I'm hoping you had your data backed up.

HT1420 Possibility to use 1 Computer - configured with 2 user accounts - each account uses a different Apple-ID for iTunes authorization ?

I wonder if it is possible to use 1 Computer (Macbook Pro)
- configured with 2 (ore even more) user accounts (i.e. me + my kid)
- and each user account has a different Apple-ID (account) for iTunes purchases & iTunes authorization ?
I woud think that is fine in terms of the underlying license agreement refereing to re-download purchased movies, shows, apps, etc.
However, it seams that there is that miraculous 90 days restriction, which I don't understand, and which allows me only to "authorise" the Computer under one or the other account. The switch is unfortunatelly only possible every 90 days ?!?
Thanks anybody for help
Oliver

The 90 day association doesn't stop you authorising an account, it only stops you from using another account for iTunes Match or automatic downloads or redownloading its past purchases : http://support.apple.com/kb/HT4627
There are a few methods listed on this page for how you could do it e.g. multiple user acounts, same iTunes but you having separate playlists, separate iTunes libraries : http://support.apple.com/kb/HT1495

INS-40925 - One or more nodes have interfaces not configured with a subnet that is common across all cluster nodes.

Hi All,
I am facing the below error while installing Oracle RAC in Silent Mode.
SEVERE: There are no common subnets represented by network interfaces across all cluster nodes.
SEVERE: [FATAL] [INS-40925] One or more nodes have interfaces not configured with a subnet that is common across all cluster nodes.
   CAUSE: Not all nodes have network interfaces that are configured on subnets that are common to all nodes in the cluster.
   ACTION: Ensure all cluster nodes have a public interface defined with the same subnet accessible by all nodes in the cluster.
My /etc/hosts is given below.
127.0.0.1        localhost    localhost.localdomain
#Public
192.168.1.101      rac1        rac1.localdomain
192.168.1.102    rac2        rac2.localdomain
#Private
192.168.2.101    rac1-priv    rac1-priv.localdomain
192.168.2.102    rac2-priv    rac2-priv.localdomain
#Virtual
192.168.1.103      rac1-vip    rac1-vip.localdomain
192.168.1.104    rac2-vip    rac2-vip.localdomain
#SCAN
192.168.1.105    rac-scan    rac-scan.localdomain
Could you please help me to get rid of the error INS-40925....Any Idea...???

Hi Ramesh,
Please find the result of ifconfig -a from both nodes RAC1 & RAC2.
ifconfig -a in RAC1
[oracle@rac1 Desktop]$ ifconfig -a
eth0      Link encap:Ethernet HWaddr 08:00:27:17:7A:D5
          inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fe17:7ad5/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:102 errors:0 dropped:0 overruns:0 frame:0
          TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:25472 (24.8 KiB) TX bytes:3322 (3.2 KiB)
          Interrupt:19 Base address:0xd020
eth1      Link encap:Ethernet HWaddr 08:00:27:C0:AC:DB
          inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fec0:acdb/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:4 errors:0 dropped:0 overruns:0 frame:0
          TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:240 (240.0 b) TX bytes:816 (816.0 b)
          Interrupt:16 Base address:0xd240
lo        Link encap:Local Loopback
          inet addr:127.0.0.1 Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING MTU:16436 Metric:1
          RX packets:56 errors:0 dropped:0 overruns:0 frame:0
          TX packets:56 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:6394 (6.2 KiB) TX bytes:6394 (6.2 KiB)
virbr0    Link encap:Ethernet HWaddr 52:54:00:CC:BD:FB
          inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0
          UP BROADCAST MULTICAST MTU:1500 Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
virbr0-nic Link encap:Ethernet HWaddr 52:54:00:CC:BD:FB
          BROADCAST MULTICAST MTU:1500 Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:500
          RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
ifconfig -a in RAC2
[oracle@rac2 Desktop]$ ifconfig -a
eth0      Link encap:Ethernet HWaddr 08:00:27:C9:38:82
          inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fec9:3882/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:122 errors:0 dropped:0 overruns:0 frame:0
          TX packets:59 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:32617 (31.8 KiB) TX bytes:5157 (5.0 KiB)
          Interrupt:19 Base address:0xd020
eth1      Link encap:Ethernet HWaddr 08:00:27:90:B5:A0
          inet addr:192.168.2.102 Bcast:192.168.2.255 Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fe90:b5a0/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:4 errors:0 dropped:0 overruns:0 frame:0
          TX packets:11 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:240 (240.0 b) TX bytes:746 (746.0 b)
          Interrupt:16 Base address:0xd240
lo        Link encap:Local Loopback
          inet addr:127.0.0.1 Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING MTU:16436 Metric:1
          RX packets:56 errors:0 dropped:0 overruns:0 frame:0
          TX packets:56 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:6390 (6.2 KiB) TX bytes:6390 (6.2 KiB)
virbr0    Link encap:Ethernet HWaddr 52:54:00:CC:BD:FB
          inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0
          UP BROADCAST MULTICAST MTU:1500 Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
virbr0-nic Link encap:Ethernet HWaddr 52:54:00:CC:BD:FB
          BROADCAST MULTICAST MTU:1500 Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:500
          RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

Error in Proxy configuration with SLM

> Hello Experts,
>
> I am encountring some problems when configuring SLM with Solution Manager 7.01 SP06. I have applied all the settings required for SLM and described on the How-To documentation. I have also read all the forums regarding this issue, but nothing helpful. This issue is the configuration of the proxy settings. We are using SNC for our Saprouter, so I assume that I have to use also the sapserv3 for SLM configuration, with the port 8080.
>
> I have added also these entries on Web Service Container in VA:
> Proxy Host: sapserv3
> Proxy Port: 8080
> Exclude List: myhost.mydomain
> And Save
>
> When I execute the configuration check with the transaction "/n/tmwflow/mopzcfg", I have these errors:
>
> <description>Check Proxy settings for download</description>
> + <config-path>
> <entry>Configuration path: SDT/SDT|cod-zeus|PS1/SDTExecutionService/DOWNLOAD</entry>
> </config-path>
> - <input>
> <entry>Proxy use: true</entry>
> <entry>Proxy host: sapserv3</entry>
> <entry>Proxy port: 8080</entry>
> <entry>Use proxy authentication: false</entry>
> <entry>Check HTTP connection to: http://www.sap.com/index.epx</entry>
> </input>
> - <output>
> <entry>Test Result: FAILED</entry>
> </output>
>- <error>
>- <MESSAGE>
> <ID>java.net.UnknownHostException: BAEx.Failed</ID>
> <CREATOR>SLM: java.net.PlainSocketImpl: Line: 201</CREATOR>
> <TEXT>www.sap.com</TEXT>
> </MESSAGE>
> </error>
> </CheckResult>
> - <CheckResult status="FAILED">
> <description>Check Proxy settings for web services</description>
> - <config-path>
> <entry>Configuration path: WebServicessAddOn/HTTPProxy</entry>
> </config-path>
> - <input>
> <entry>Proxy use: true</entry>
> <entry>Proxy host: sapserv3</entry>
> <entry>Proxy port: 8080</entry>
> <entry>Check HTTP connection to: http://www.sap.com/index.epx</entry>
> <entry>Set Proxy-Authorization</entry>
> </input>
> - <output>
> <entry>Proxy user:</entry>
> <entry>Test Result: FAILED</entry>
> </output>
>- <error>
>- <MESSAGE>
> <ID>java.net.UnknownHostException: BAEx.Failed</ID>
> <CREATOR>SLM: java.net.PlainSocketImpl: Line: 201</CREATOR>
> <TEXT>www.sap.com</TEXT>
> </MESSAGE>
> </error>
> </CheckResult>
> - <CheckResult status="FAILED">
> <description>Check SMP user and SP web service</description>
>
> Configuration path: SDT/SDT|host|sid/SDTExecutionService/DOWNLOAD
>
> please tell me what should I do. Thank you
Edited by: sapmoo on May 7, 2010 11:59 AM

is Done...
I have changed the 8001 Port, by 50100... :S
this is my First Client with both instances in a same Server than I have to use this port... always I have used 800 + number of Instance...
Regards

Is it possible to use variant configuration (with a Non-SAP solution) when creating ERP sales orders in SAP CRM WebUI

Hello,
our customer plans to use a Non-SAP solution for variant configuration (Camos) in SAP ERP (ECC 6.0) and in SAP CRM 7.0 EHP1 as well.
ERP sales orders (and ERP quotations) should be created in SAP CRM (CRM WebUI).
Is it possible to use variant configuration (with an external variant configuration tool) when creating ERP sales orders and quotations in the SAP CRM WebUI or do we have to implement SAP IPC for this?
Thanks in advance.
Regards,
AEV

Dear AEV,
I think LORD (lean orders) should work with variant configuration as well. In the note 1236015 there is not restriction listed. However you need lord2 activated in ECC, and ECC system should be on EHP4.
Best regards
Rene

When I try to reformat there is an error message about configurations with the pointing device

When I try to reformat there is an error message about configurations with the pointing device
I am not sure I am on the correct section in the support area for Lenovo.
I had a mouse issue. It was unable to read the mouse. Now the mouse is working and it is initialized.
I have no idea why.
There is an error message saying that I should press F 1or F2. I pressed down F 1 and I tried to work with it and I enabled the mouse or I tried. The mouse is working fine but the computer will not recover completely the way it used to.
It is very confusing. When I shut down and restart there is an message that was not there before about the pointing device. Also the recovering operation never asked me for disks. Now it is doing that. I have disks but this is all confusing. I just want the computer to be the way it was. It is working fine except for booting up and the messages.

Hi marissa, welcome to the forums,
you may or may not be in the right place, but it would certainly help members to help you if you could post exactly which Lenovo system; notebook / computer, you have and which operating system is installed on it.
Thanks in advance
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

HT5927 Using apple configurator with supervised devises, enabling iCloud/ find my iOS device (after being supervised), backing up that supervised / find my iPhone enabled image, --issue; unable to apply back up to any iOS device (including the orign. devi

Senario:
Need to manage 500 Enterprise iPads
Requirements;
1) Trackable via Find my iOS device (we have 500 iPads and with the 100 device limit per iCloud account for Find my iOS device limit we have 5+ iCloud accounts).
2) Individually named iPads for locating and sending commands to wipe, lost mode, etc.. on map per Find my iOS device (we uniquely name them in Apple Configurator either by using the "sequensetially numbering feature", or by creating individual back ups (yes, 450) with the name specified in the image).
3) Find my iOS device feature enabled in base Prepared or Supervised image (using one of our 5+ iCloud accounts) (image can be created during prepared stage, or in supervised stage) - tried both and have the same issue - which I am getting to...
4) VPP codes for paid apps (all VPP codes purchased with generic account which is the Apple Admin account for VPP purchases). Apple Configurator is set up under a different/ unique Apple account (i.e. not VPP admin account) and not logged into iTunes for any purchases/ services).
Issue: Can not do any following senarios;
A)
1) configure master iOS 7 iPad with iCloud account with Find my iOS feature enabled in Prepare stage (added during preparing stage)
2) configure master iOS 7 iPad with iCloud account with Find my iOS feature enabled in Supervised stage (added after supervising, and then backing up that supervised and iOS Find my iOS device enabled)
B) 1) Apply master image to any Supervised iPad (under senario step A) or senario step B)), including the (Supervised or/ Prepared iPad that was used to create the maset iOS 7 image
Result = fail with Apple generic code "4" ; This is obviously due to Find my iOS device feature enabled during image capture.
According to Apple (see Apple Config. Help) the 'Activation lock' (new feature in iOS 7) will not be enabled on a supervised device when an iCloud account with "Find my iDevice" is enabled. Their "help files" seem to imply after the device is Supervised, and a person (presumably and end user) adds thier own iCloud account with Find my iOS device enabled the activation lock is not enabled and erasing/ reconfiguring with Apple Configurator will not cause reimaging probhlems such as requiring the end user's credentials to reconfigure the device using Apple Configurator (i.e. you won't need the end user's credentials).
Needed: To be able to configure Supervised iPads with iCloud account (Enterprised owned iCloud account) configured on the basse image, which has Find my iOS device enabled, and to be able to apply that base image to all Enterprise iPads without generic apple error code 4 issue.

Hi all
I am trying to replicate these steps in my environment but I am having trouble getting an iCloud backup restored to a supervised device. Can someone clarify the steps? The parts I am unsure on are:
1) Do you Prepare in Configurator with all the institution owned apps? Or do you install them after restoring the iCloud backup?
2) After entering the personal AppleID to restore the iCloud backup, the setup wizard prompts for the Institution/Configurator AppleID, there is an option to 'Skip Now'. Do you enter in the password for the institution account? or do you skip that step?
3) What exactly is on the screen in the 'mini setup assistant' after the restore when you Refresh with Configurator?
Any help would be greatly appreciated!

IPhone mail configured with Gmail alternate address

I'm really stuck.. I have a Gmail account (through Google Apps for Business) that I have configured with Mail on my iPhone using Exchange to connect the account. Everything has been working flawlessly, until my employer made a change to our email addresses, so that we had to set up a new domain alias through Gmail as our "send from" account.
My problem is that I can't for the life of me figure out how to send from this new address from my iPhone.
Finally, I found a post on the web that seems to explain a way to do this, using the OTHER account setup (IMAP) on the iPhone (instead of either Gmail or Exchange): http://modernerd.com/post/535350679/solved-gmail-ipad-iphone-and-multiple-from That seemed to do the trick, except then I realized I would no longer have Push email, which I have really come to rely on.
I tried using the native iPhone Gmail app for a few days, as that seemed to be the only solution, but there's just so many things about that app that really make me miss my good 'ol Apple mail.
Any other creative solutions out there? Thanks for any advice!

yeah, it used to work fine because google was supported exchange on mobile devices up until the end of february or so. they let everyone keep their settings the way they were unless they changed them or deleted them, so that's totally expected. The thing with the push is that gmail no longer seems to be supporting that behavior through native apps on mobile devices because it's something they want their exchange customers to pay for

Problem With Cutom Configuration with Object Type

Dear Guru's
I am working WebUI, I am facing a problem with Custom Configuration.
1. The initial requirement to control the visibility for a dropdown event in ERP Quotation.
2. To this i copied the default configuration to custom configuration with custom Object type and Subtype.
       CONFIG KEY: ZPJQTN
       OBJECT TYPE: ZOTYP_CONFIG
       OBJECT SUB TYPE: ZSTYPE_CONFIG1
3. I have created customm fields in enhancement.
4. Now i chosen my new configuration (ZPJQTN,ZOTYP_CONFIG,ZSTYP_CONFIG1), when i click Show available fields, the custom fields are not showing. Instead the created fields are available at other configuration.
5. I am able to control the visibility for the standard available fields.But i am not getting the custom created fields
(Note: I have created the Object type and Object sub type as follows: SPRO->CRM->UI Framework->Define Object Types
Object type: ZOTYP_CONFIG Callback class: ZCL_CONFIG_CALLBACK
Redifned the method: IF_BSP_DLC_OBJ_TYPE_CALLBACK~GET_OBJECT_SUB_TYPES
Coded as below:
data: lv_subtype type bsp_dlc_object_sub_type.
lv_subtype = 'ZSTYP_CONFIG1'.
append lv_subtype to result.
lv_subtype = 'ZSTYP_CONFIG2'.
APPEND lv_subtype to result.
Now Please suggest me how to achieve this.
Also please let me know, whether i am following the correct procedure for controlling the visibility.
Thanks in Advance,
S.Meganadhan.

Hi Harshit,
I added custom fields using AET only.
I am able to see the field got added in the structure. I am able to access GET and SET methods of the field.
But the problem is, it is not getting saved. Am i missed any configuration step?
Please suggest me.
Thanks in advance,
Regards,
S.Meganadhan.

BPM 11g install and configuration with Webcenter

Hi,
I am new to this BPM so need some help in installation. Where can I download the latest version of BPM 11g and for installating it what steps do I need to follow. Also I need to integrate Webcenter also so for webcenter integration what do I need to install and configure with BPM 11g.
Do I need to install webcenter full suite for integration with BPM and if so can I install both BPM and webcenter in one home iteself. Where can I find some documentation arround installing BPM and configuring with Webcenter.
Thanks

Hi,
Need some info on the install I have to install both SOA BPM 11g 11.1.1.3 and Webcenter 11.1.1.3 on the same box. I have installed the SOA BPM 11.1.1.3 but wanted to find out what is the best option of installing Webcenter 11.1.1.3 as I need to integrat SOA BPM 11g 11.1.1.3 and Webcenter 11.1.1.3. Here is what I think are the options but don't know which one should I go for or is there any other option but the fact is I need to install both on the same box.
*1. Should I install Webcenter in a separate HOME in doing so I will end up installing weblogic again and then install webcenter. Will endup having two ORACLE HOMES one for SOA BPM and one for Webcenter.*
*2. OR should I install Webcenter in the same home as SOA BPM and create a new domain in doing so what happens to some of the components that are installed when installing SOA BPM.*
*3. OR should I just extend the SOA BPM Domain and have both SOA BPM and Webcenter installed in the same domain. I believe this will only add the webcenter components but don't know if there are any issues.*
And help is really appreciated..
Thanks

I am trying to use apple configurator with ipads. I have been successful with all our ipads but 1. It will not allow me to add apps. The error I get is that it is refreshed but with errors e

I am trying to use apple configurator with ipads. I have been successful with preparing and supervising all ipads but one. When preparing it in configurator, I receive an error that it is refreshed but with an error. Under supervise, I am not able to add apps. I have erased all content to start over but this does not work either

Are you trying to restore a backup, or just sync some apps? Do you have profiles installed on the device?
Have you plugged the ipad into iTunes, and did a fresh install? I'm assuming the device went through the prepare setup properly. You many have to unsupervise it first, then plug it into iTunes to wipe it completely.
I'd then do each step seperately. Prepare it, then install 1 app, if that works, try another app, then maybe a profile.

Waas configuration with NME

Similar Messages

Maybe you are looking for