WAAS pass-through connections
I gather that a connection through a WAE can be in pass-through for one of 3 reasons :
- the remote WAE is not detected through the 3 way TCP handshake (conn type 'PT No Peer'
- the connection already exists (conn type 'PT In Progress')
- the connection is set to pass-through as it has hit a policy which puts it in pass-through mode (conn type ??)
In the output of the 'show tfo conn list' command, what is the 'Conn Type' for a connection that is being passed through because of a pass through policy ?
Thanks
Nigel
Nigel,
The potential pass-through reasons are:
PT App Cfg
PT Dst Cfg
PT_Glb Cfg
PT Overload
PT In Progress
PT PE Int Error
PT Dyn Bypass
PT No Peer
PT Rjct Capabilities
PT Rjct Resources
PT Asym Client
PT Asym Server
PT Intermediate
PT FB Int Error
PT AD Int Error
PT App Override
PT Server Blacklist
Regards,
Zach
Similar Messages
-
RV042G cannot support more than 2-3 IPSec Pass through connections
Hi,
I'm trying to figure out what the max number of IPSec VPN pass through connections the RV042G can handle. We bought an RV042G router to replace our old RV042 box which was running into connection limitations. There are approximately 15 people in the office and anywhere from 5-8 of them need to vpn to a single client site. There seems to be an issue with UPNP where it creates the proper port forwarding but doesn't associate it with an internal IP address. Giving each workstation a static internal IP doesn't solve this issue. The remote site we are connecting to does have NAT-T turned on. What ends up happening is that after a while, users cannot vpn. Sometimes it happens with fewer than three users. Clearing the UPNP and rebooting the router helps but eventually if you connect and disconnect, a few times, you're hosed. The UPNP doesn't release the setting it makes in a timely fashion. Is there any way to fix this besides turning off UPNP which we need for other software to work?Lenovo support (for me in Canada at least) is based in Atlanta, so I'm surprised you found a tech with bad English...
Your problems sound like windows problems, not hardware problems -- are you running XP or Windows7? If you google based on your OS, there are threads to be found on slowing down the start menu behaviors. -
Can somebody elaborate more on the following:
10.182.2.130:27385 161.141.105.217:139 Internal Server
10.182.2.130:20814 10.220.3.150:139 Internal Server
10.182.2.130:26997 161.141.105.217:445 Internal Server
10.182.2.130:18271 10.220.3.75:445 Internal Server
10.182.2.130:22309 10.220.139.150:445 Internal Server
10.182.2.130:60711 10.220.136.21:139 Internal Server
10.182.2.130:15729 10.179.12.91:139 App Dyn Mtch Non-Optimized
What it means by Interal Server and Non-Optimized under the pass-through connections. If this is a problem what would be the direction for a resolution. All I see are ports 139 and 445.George,
The 'Internal Server' designation means that the connection was initiated from an internal server process within the WAE. An example of this would be the WAFS AO performing CIFS server auto-discovery.
The 'App Dyn Mtch Non-Optimized' designation means that the connection has been forced via an dynamic policy match to be accounted for as non-optimized, even though the connection may be optimized.
Is 10.182.2.130 one of your WAE devices running the WAFS Edge or Core service?
Zach -
Static NAT pass-through; can not get to work
I am not having any luck getting a static NAT pass-through to work.
BM3.8/NW6.5 all patched to the latest patches (no betas). IPFLT is NOT
loaded.
My internal network on one LAN all have 10.100.xxx.xxx private addresses.
Dynamic NAT works great.
I have secondary public IP addresses bound to my public NIC. Static NAT
mapping between the secondary public IP addresses and the couple of
individual private addresses work just fine. In other words, all has been
working fine.
I need to give one of those internal resources its public IP address
(change it's private to its public).
OK, I went into the NAT table and changed the proper public <-> private to
public <-> public (identical addresses). I changed the internal computer
to it's public address/mask with the same default gateway the server is
using. The internal computer can now only ping itself; can't even ping
it's default gateway. I did reinitialize, and also restarted. I can not
get the pass-through connection to work.
Any thoughts will be well received.
BobRobert,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://support.novell.com/forums)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://support.novell.com/forums/faq_general.html
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/ -
N1K 10Gb Pass through to 2232p/5K
Hello,
We are about to implement Nexus 1000v's on HP ESX hosts using vCenter 5.0.
The ESX hosts will each be using 2 - 10Gb pass throughs connected to two different 2232P's which are support by two N5K's.
I am configuring the uplink port-profile to use the following:
channel-group auto mode active
Which will, if I understand correctly, use LACP so that each interface of a given VEM will be part of a port-channel.
What I need to know is there any special configuration that I need to make on the 5K's to support the VEM's port channels?
Do I need to create a seperate port-channel for each of the VEM's (on the 5K) before I have the server admins bind the physical interfaces to the uplink port-profile?
The 1000v's are version 4.2(1)SV1(4a) and the 5K's are version 5.0(3)N1(1c).
Thanks!
BobHello Robert,
You have the right idea. Each VEM will need a separate VPC port-channel on the n5ks. Search for Nexus 1000v Port Channel Best Practices for a full configuration.
Note we have seen issues where the HP Passthrough and SeverEngines NICS drop LACP PDUs. A firmware update on the Passthrough and/or NICS will correct this behavior.
Matthew
Sent from Cisco Technical Support iPhone App -
My phone does not want to come on pass the 'connect to itunes' logo on the screen. This happened after I was updating the phone software through itunes, and itunes said I needed to restore my phone if it is to work with itunes, which I did. An error (1015) box popped up and... well.... here we are. I have an iphone 3G. The support coverage is expired.
I just want to return to my phone functioning as before.Was this iPhone jailbroken?
-
Does IPv6 traffic "pass-through" or "drop" by cisco waas?
Since cisco waas is not yet supported IPv6, if i am running IPv4 and IPv6 dual stack mode on the same circuit, does IPv6 traffic get dropped by the waas or does waas put IPv6 traffic in "pass-through" mode and let it goes? I am thinking, waas will treat IPv6 as non-IP traffic and will let it goes. Am i right?
Hi Joe and Kanwai,
One note though - if your running WCCP as the redirection mode, you won't get the IPv6 traffic redirected, as WCCP does NOT support IPv6. Hence you won't see IPv6 traffic at all on the WAAS device.
Best Regards
Finn Poulsen -
Cisco ASA 5505 L2TP Pass through
I am having trouble with L2TP pass through on an ASA 5505 device.
L2TP server: OSX 10.6
I can connect with any OSX system and it works fine straight away.
When connecting with a windows computer I get a 789 error. "Error 789: The L2TP connection attempt failed because the security layer encountere a processing error during the initial negotiations with the remote computer."
I did not setup or configure the device to start with and apart from this issue its working fine so I am hessitant at trying to just mess around too much to try and find the problem.
I am using the ASDM 6.4 to manage the device.
Ports look to be forwarded correctly; 1701, 4500 & 500 UDP.
Im just looking for other common issues?
RobBelow is the commands you wanted.
Where you see: IPNOTWHATIWASEXPECTING
This is an IP I dont know. possible and old IP address.
and
default-domain value domain-notcorrect.local
This is an old domain from years ago.
Result of the command: "show run crypto"
crypto ipsec transform-set aes-sha esp-aes esp-sha-hmac
crypto ipsec transform-set aes-192-sha esp-aes-192 esp-sha-hmac
crypto ipsec transform-set aes-256-sha esp-aes-256 esp-sha-hmac
crypto ipsec transform-set 3des-sha esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set transform-amzn esp-aes esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map map-dynamic 1 set pfs group5
crypto dynamic-map map-dynamic 1 set transform-set aes-256-sha aes-192-sha aes-sha 3des-sha
crypto dynamic-map map-dynamic 2 set pfs
crypto dynamic-map map-dynamic 2 set transform-set aes-256-sha aes-192-sha aes-sha 3des-sha
crypto dynamic-map map-dynamic 3 set pfs
crypto dynamic-map map-dynamic 3 set transform-set aes-256-sha aes-192-sha aes-sha 3des-sha
crypto dynamic-map map-dynamic 4 set transform-set aes-256-sha aes-192-sha aes-sha 3des-sha
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set peer IPNOTWHATIWASEXPECTING3
crypto map outside_map 1 set transform-set ESP-DES-SHA
crypto map outside_map 2 match address acl-amzn
crypto map outside_map 2 set pfs
crypto map outside_map 2 set peer IPNOTWHATIWASEXPECTING IPNOTWHATIWASEXPECTING
crypto map outside_map 2 set transform-set transform-amzn
crypto map outside_map 255 ipsec-isakmp dynamic map-dynamic
crypto map outside_map interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 86400
crypto isakmp policy 2
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 3
authentication pre-share
encryption aes-256
hash sha
group 1
lifetime 86400
crypto isakmp policy 11
authentication pre-share
encryption aes-192
hash sha
group 5
lifetime 86400
crypto isakmp policy 12
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 13
authentication pre-share
encryption aes-192
hash sha
group 1
lifetime 86400
crypto isakmp policy 21
authentication pre-share
encryption aes
hash sha
group 5
lifetime 86400
crypto isakmp policy 22
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 23
authentication pre-share
encryption aes
hash sha
group 1
lifetime 86400
crypto isakmp policy 31
authentication pre-share
encryption 3des
hash sha
group 5
lifetime 86400
crypto isakmp policy 32
authentication rsa-sig
encryption des
hash sha
group 1
lifetime 86400
crypto isakmp policy 33
authentication pre-share
encryption 3des
hash sha
group 1
lifetime 86400
crypto isakmp policy 34
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
Result of the command: "show run group-policy"
group-policy evertest internal
group-policy evertest attributes
dns-server value 10.100.25.252
vpn-idle-timeout 720
vpn-tunnel-protocol IPSec l2tp-ipsec
pfs enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpnsplittunnel
default-domain value domain-notcorrect.local
group-policy petero internal
group-policy petero attributes
dns-server value 10.100.25.252
vpn-idle-timeout 720
pfs enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpnsplittunnel
default-domain value domain-notcorrect.local
group-policy awsfilter internal
group-policy awsfilter attributes
vpn-filter value amzn-filter
group-policy vpnpptp internal
group-policy vpnpptp attributes
dns-server value 10.100.25.252
vpn-tunnel-protocol l2tp-ipsec
group-policy vanheelm internal
group-policy vanheelm attributes
dns-server value 10.100.25.252
vpn-idle-timeout 720
vpn-tunnel-protocol IPSec l2tp-ipsec
pfs enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpnsplittunnel
default-domain value domain-notcorrect.local
group-policy ciscoVPNuser internal
group-policy ciscoVPNuser attributes
dns-server value 10.100.25.10
vpn-idle-timeout 720
pfs enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpnsplittunnel
default-domain value domain-notcorrect.local
group-policy chauhanv2 internal
group-policy chauhanv2 attributes
dns-server value 10.100.25.252
vpn-idle-timeout 720
pfs enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpnsplittunnel
default-domain value domain-notcorrect.local
group-policy oterop internal
group-policy oterop attributes
dns-server value 10.100.25.252
vpn-idle-timeout 720
vpn-tunnel-protocol IPSec l2tp-ipsec
pfs enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpnsplittunnel
default-domain value domain-notcorrect.local
group-policy Oterop internal
group-policy Oterop attributes
dns-server value 10.100.25.252
vpn-idle-timeout 30
group-policy chauhanv internal
group-policy chauhanv attributes
dns-server value 10.100.25.252
vpn-idle-timeout 30
vpn-tunnel-protocol IPSec l2tp-ipsec
group-policy bnixon2 internal
group-policy bnixon2 attributes
dns-server value 10.100.25.252
vpn-idle-timeout 720
vpn-tunnel-protocol IPSec l2tp-ipsec
pfs enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpnsplittunnel
default-domain value domain-notcorrect.local
Result of the command: "show run tunnel-group"
tunnel-group ciscoVPNuser type remote-access
tunnel-group ciscoVPNuser general-attributes
address-pool vpnippool
default-group-policy ciscoVPNuser
tunnel-group ciscoVPNuser ipsec-attributes
pre-shared-key *****
tunnel-group petero type remote-access
tunnel-group petero general-attributes
address-pool vpnippool
default-group-policy petero
tunnel-group petero ipsec-attributes
pre-shared-key *****
tunnel-group oterop type remote-access
tunnel-group oterop general-attributes
address-pool vpnippool
default-group-policy oterop
tunnel-group oterop ipsec-attributes
pre-shared-key *****
tunnel-group vanheelm type remote-access
tunnel-group vanheelm general-attributes
address-pool vpnippool
default-group-policy vanheelm
tunnel-group vanheelm ipsec-attributes
pre-shared-key *****
tunnel-group chauhanv type remote-access
tunnel-group chauhanv general-attributes
default-group-policy chauhanv
tunnel-group Oterop type remote-access
tunnel-group Oterop general-attributes
default-group-policy Oterop
tunnel-group chauhanv2 type remote-access
tunnel-group chauhanv2 general-attributes
address-pool vpnippool
default-group-policy chauhanv2
tunnel-group chauhanv2 ipsec-attributes
pre-shared-key *****
tunnel-group bnixon2 type remote-access
tunnel-group bnixon2 general-attributes
address-pool vpnippool
default-group-policy bnixon2
tunnel-group bnixon2 ipsec-attributes
pre-shared-key *****
tunnel-group vpnpptp type remote-access
tunnel-group vpnpptp general-attributes
address-pool vpnippool
default-group-policy vpnpptp
tunnel-group IPNOTWHATIWASEXPECTING4 type ipsec-l2l
tunnel-group IPNOTWHATIWASEXPECTING4 ipsec-attributes
pre-shared-key *****
tunnel-group evertest type remote-access
tunnel-group evertest general-attributes
address-pool vpnippool
default-group-policy evertest
tunnel-group evertest ipsec-attributes
pre-shared-key *****
tunnel-group evertest ppp-attributes
authentication ms-chap-v2
tunnel-group IPNOTWHATIWASEXPECTING3 type ipsec-l2l
tunnel-group IPNOTWHATIWASEXPECTING3 ipsec-attributes
pre-shared-key *****
tunnel-group IPNOTWHATIWASEXPECTING2 type ipsec-l2l
tunnel-group IPNOTWHATIWASEXPECTING2 general-attributes
default-group-policy awsfilter
tunnel-group IPNOTWHATIWASEXPECTING2 ipsec-attributes
pre-shared-key *****
isakmp keepalive threshold 10 retry 3
tunnel-group IPNOTWHATIWASEXPECTING type ipsec-l2l
tunnel-group IPNOTWHATIWASEXPECTING general-attributes
default-group-policy awsfilter
tunnel-group IPNOTWHATIWASEXPECTING ipsec-attributes
pre-shared-key *****
isakmp keepalive threshold 10 retry 3
Result of the command: "show vpn-sessiondb detail remote filter protocol L2TPOverIPsec"
INFO: There are presently no active sessions of the type specified
Result of the command: "show vpn-sessiondb detail remote filter protocol L2TPOverIPsecOverNAT"
INFO: There are presently no active sessions of the type specified -
How can I have each pass through a for loop communicate with a new indicator?
Hello,
I am using 16 color boxes to indicate how 16 channels are behaving. If a color box is blue, its respective channel is running correctly, red means it has failed etc. I am continuously checking each channel using a loop, and I wanted to update the channel colors every loop. I have made an array of 16 numbers corresponding to the color I wish to have (which are blue = running, red = failed, green = completed, black = not in use). However, I cannot find a way to pull these 16 numbers out of the array and to the color boxes short of 16 index arrays connected to the color boxes.
I understand how to convert each individual number to a color, I just don't know how to use a 16 times for loop to communicate with a different color box each pass through. Is there any way to do this or should I just go for brute force?
Thank you.
Solved!
Go to Solution.Sorry I keep making new posts. Attached is an example i wrote up. There are three cases in the disabled structure, each has a different implementation of what i belive your specs are.
Tim Elsey
LabVIEW 2010, 2012
Certified LabVIEW Architect
Attachments:
update color box.vi 24 KB -
USB Pass-Through From Windows 8.1 Host To Windows Server 2012 R2 VM
I want to be able to connect with a Windows Mobile Device through Windows Mobile Device Center, within a Virtual Machine. When connecting through the Hyper-V Manager and through Remote Desktop, under "Other supported RemoteFX USB devices",
I can see the Symbol USB Sync Cradle. In the VM, in Device Manager, I don't see a USB connection. In the VM, I don't see any meaningful errors in the Event Viewer.
Host: Windows 8.1 Enterprise Hyper-V on a Domain. Upgraded from Windows 8.1 Pro. When this computer was originally installed with Windows 8 Pro, Hyper-V was enabled. I removed Hyper-V, and installed VMWare Player, because I wanted
USB Pass-through. I then uninstalled VMWare and installed VirtualBox. Recently, I uninstalled VirtualBox, upgraded to Windows 8.1 Enterprise, and enabled Hyper-V.
Virtual Machine OS: Windows Server 2012 R2 on a Workgroup. Started out with being a VMWare VM, using VMWare Player. Moved to VirtualBox. USB Pass-through was working in both those virtual environments. Used Disk2VHD to convert the
VM to a VHDX file.
On the Host:
Windows Mobile Device Center is connected to a Motorola Windows Mobile Device (MC959X) sitting in a Symbol USB Cradle. The OS on the scanner is Windows Embedded Handheld 6.5 Classic CE OS 5.2.29217 (Build 29217.5.3.12.26). Advanced Networking
(USB to PC) is not enabled.
Enabled RemoteFX.
In the RDP file, and in the Registry, added the GUID's for:
WPD "{eec5ad98-8080-425f-922a-dabf3de3f69a}";
Windows Mobile "{6AC27878-A6FA-4155-BA85-F98F491D4F33}";
USB Device "{88BAE032-5A81-49f0-BC3D-A4FF138216D6}";
Windows CE USB Device "{25dbce51-6c8f-4a72-8a6d-b54c2b4fc835}";
GUID_DEVINTERFACE_USB_DEVICE "{A5DCBF10-6530-11D2-901F-00C04FB951ED}"
Ran "sfc /scannow"
All Microsoft Updates are current.
What am I missing?I hope it's something like that. Those features have been installed. Here's what PowerShell shows is installed:
PS C:\Windows\system32> Get-WindowsFeature |Where {$_.Installed -eq "True"} | ft DisplayName, Installed
DisplayName
Installed
File and Storage Services
True
File and iSCSI Services
True
File Server
True
Storage Services
True
Remote Desktop Services
True
Remote Desktop Licensing
True
Remote Desktop Session Host
True
Web Server (IIS)
True
Web Server
True
Common HTTP Features
True
Default Document
True
Directory Browsing
True
HTTP Errors
True
Static Content
True
HTTP Redirection
True
Health and Diagnostics
True
HTTP Logging
True
Performance
True
Static Content Compression
True
Security
True
Request Filtering
True
Windows Authentication
True
Application Development
True
.NET Extensibility 3.5
True
.NET Extensibility 4.5
True
ASP.NET 3.5
True
ASP.NET 4.5
True
ISAPI Extensions
True
ISAPI Filters
True
Management Tools
True
IIS Management Console
True
.NET Framework 3.5 Features
True
.NET Framework 3.5 (includes .NET 2.0 and 3.0)
True
.NET Framework 4.5 Features
True
.NET Framework 4.5
True
ASP.NET 4.5
True
WCF Services
True
TCP Port Sharing
True
Ink and Handwriting Services
True
Media Foundation
True
Remote Server Administration Tools
True
Role Administration Tools
True
Remote Desktop Services Tools
True
Remote Desktop Licensing Diagnoser Tools
True
Remote Desktop Licensing Tools
True
SMB 1.0/CIFS File Sharing Support
True
User Interfaces and Infrastructure
True
Graphical Management Tools and Infrastructure
True
Desktop Experience
True
Server Graphical Shell
True
Windows PowerShell
True
Windows PowerShell 4.0
True
Windows PowerShell 2.0 Engine
True
Windows PowerShell ISE
True
WoW64 Support
True -
Xbox 360 - Optical line-in pass through 5.1 to optical line-out on an iMac?
Hi guys, i'm in the market to purchase a new 5.1 surround sound system for my room and the following issue has been purplexing me.
IS it possible to daisy chain my XBOX 360 to my iMac with optical cables and pass through 5.1 surround sound to the decoder on the sound system?
So i'd have an optical cable from my xbox to the line-in on my iMac. I'd use Rogue Amoeba's Line-In app to pass the sound through to the optical line-out and through to the sound system.
(I know it works using stereo sources, but i don't know about 5.1 digital sound.)
I also know i could just connect them both to separate optical ports on the sound sytem, but i'm trying to listen to 2 sources at the same time. (5.1 from XBOX and music from iMac).
Any thoughts on this are appreciated!I'm convinced things work like this:
The SBX-Fi receives the encoded SPDIF.<
The drivers decode it into the 5 digital audio signals. This siimply regenerates what was put into the encoding and has no effect on its "volume."<
The 5 digital audio signals are sent to the SBX-Fi hardware, as is.<
The signals are widened (not sure about the SBX-Fi, but for SBLi've-/SBAudigy-series card it's 32-bits with IIRC 4 bits for headroom, which is 24dB) at input by the SBX-Fi hardware. The additional headroom is probably able to handle most effects/mixing which might happen, but might produce a signal which would clip on output if the intermediate results produce a digital volume over 00%.<
The master output volume operates on the output signals before they are narrowed.<
The output signals are narrowed (dithered) and distributed.<
If that's correct, it means you should be able to simply lower the master output volume in the soundcard mixer; and that presumes something's going on like high Crystalizer settings, or something; to elminate clipping distortion.
-Dave
?[email protected] -
I wonder if anyone could please help. I have just bought AppleTV and am trying to use it with my old Samsung DLP (with no HDMI but DVI) and a Denon AVR 789 (witch has HDMI pass-through) . When I connect the AppleTV through the receiver (using a HDMI lead to HDMI, them HDMI to DVI) I get no picture. When I go directly from the AppleTV to the TV using HDMI to DVI it works fine. I have tried changing the cables and also when I connect my FIOS TV box through the receiver it works fine. Also my AppleTV software is up to date Could this be something to do with HDCP ?
I would be grateful of any helpYes it could be HDCP.
Generally, I would look at the source device (tv) as the root of the problem in that it doesn't handle HDCP hopping properly, however the tv works with other receivers so I have to have my doubts about where blame lies for these problems.
You could try powering up the devices in a different order, say from the delivery end first.
It could be however that you simply don't have the receiver set correctly and need to match up the inputs and outputs. -
Analog to digital, how does one actually pass through a TRV120 or TRV950E ?
I would need some technical advice on how to connect a camera with pass-through feature in between a VCR and the computer.
I am trying to copy VHS-C cassettes to the Mac via a Digital8 Sony TRV-120. I use A/V pin connector from the VCR, Firewire to the Mac. I get the VCR image on the TRV's LCD, but nothing on the Mac. iMovie says the camcorder is empty, dot. If I put a tape inside, iMovie launches the tape and I get the image from the tape. I was pretty certain that the TRV-120 had the pass-through feature, having seen it mentioned on some reviews. Is there a special manipulation to do? Or do I need the sVHS cable? (would be weird).
Otherwise, I tried the TRV950E as a converter. The only way I could make the link work through is by recording the analogue signal onto the camcorder tape. I thought it would be easier, am I missing something?
Thanks in advance for your help!
PaulIn my unnEUtered Sony TRV320E Analog to DV passthrough goes like this:
1. Take the tape out of the camcorder
2. Connect the analog device's audio and video to the camcorder's minijack, use the S-Video jack for video if the output device supports S-Video
3. Put the camcorder into VTR-mode
4. Select A/V->DV out: ON, in VTR mode's menu choices
5. Disable the info display on the the camcorder by toggling its DISPLAY button
6. Put iMovie (or other DV application) to the Camera Mode
The analog image should now appear on the camcorder's screen as well as on the iMovie's screen.
Note that if you have a tape in the camcorder, you have to put the camcorder's VTR into REC mode (you may pause the tape) but this is not advisable because it produces wear to the tape.
* Note that the SCART which comes with the European nEUtered TRV320E camcorder is Out-only.
Notice that some analog to DV passthrough converters (like the TRV320E) don't work in iMovie HD 6.0.2 like they do in iMovie 4.0.1:
http://www.sjoki.uta.fi/~shmhav/iMovieHD_6_bugs.html#analogDV -
Analog to digital pass through
First of all I apologize if this has already been addressed. The following is what I am trying to do with my eMac computer lab at school. I am using iMovie 4 with Mac 10.2.8. I am trying to use pass through mode with iMovie and my Sony camcorder. I have the VCR going into the Sony and the Sony in VTR mode. The video shows up fine in the LCD screen of the Sony. I used a firewire cable to connect to the eMac and tried to import the video into iMovie. Nothing shows up in iMovie. Can someone please tell me what I am doing wrong? All help is greatly appreciated.
hey there Shirley,
what model of Sony cam are you using? check the manual. try a different FW cable & w/ a different Mac. is the FW connection solid & tight? have you toggled the switch below the viewer from edit(scissors icon) to import(camera icon)? do you have control of the cam for play, stop, etc...? sorry for all the questions, but better to go through the simple & sometimes overlooked first.
someone else may have more & better thoughts. also see this:
http://www.danslagle.com/mac/iMovie/index.shtml -
Video "Pass-Through" to TV Monitor?
Newbie to Final Cut Express here... does the new FC Express have a setting (like iMovie) where the video can "pass through" the connected firewire camera to a TV monitor? I want to be able to see scrubbing, playback, etc. in real time on my TV monitor as well as in the app window.
Thanks!Yes. View > Video Out > Firewire is the setting. Of course, your camera needs to be in VTR mode to do the passthrough in the correct direction.
Maybe you are looking for
-
Can not Insert data to Microsoft Access successfully
I am using Microsoft Access database, and trying to insert some data into a table with a "while" loop, but every time, the last row can not be inserted although the return value of the "executeUpdate()" is 1, can anyone tell what's wrong with that? t
-
Lion and Mavericks dual boot.
Hello everyone, I have an rMBP with Mavericks its runs fine and i'd like to install Mavericks on my 2010 (white) Macbook as well. The macbook currently runs 10.7 Lion and only has 2GB RAM, Mavericks will be even slower than 10.7. Because of that reas
-
External USB Sound Card and 6-channel 5.1 SS speakers not working
Hi. I purchased a few devices to expand my sound to 5.1 surround sound. However, I'm having trouble getting any results at all. Here's my situation. New 24-in Intel iMac Logitech G51 Surround Sound Speakers PPA International External Sound 6 Channel
-
Freeze up when I try to show or hide vault
I can not show or hide my vault. Vault is located on external usb drive. Not sure if related but I just plugged in another external drive using fire wire connection. I would like to remove my current vault and then re-create the vault on my fire wire
-
Hi ! Internet Information Services (IIS) is getting Disabled automatically on all of our SCCM 2012 Distribution Points. Please help and share configuration steps. Thank you.