WAAS using WCCP from 2 6509's?

I am preparing to install a WAE in the datacenter using WCCP for redirection of traffic to 1 of my networks on a point-to-multipoint frame relay network. Where things get foggy is the WCCP server install on my "router" which is actually 2 6509's which are used to route different vlans for both redundancy and load-balancing in the Datacenter. Is it possible/advisable to set both up with WCCP to redirect to the WAE? Could this cause any unforeseen issues?
I'm also wondering about traffic that is destined for other networks on that point-to-multipoint frame relay connection that my remote site is on which will have the other WAE. Will it be easy to specify which traffic to redirect to the WAE (that which is destined for that one remote site) or will this also cause issues?
Thanks in advance!

Karen,
With WCCP, you can have multiple WAEs (theoretically up to 32) and multiple routers (again up to 32) in the service group. So in your case, both routers can be registered to the same WAE(s). You can limit traffic via a redirect-list, which is an ACL (only accept traffic to/from your remote site).
WCCP is configured on the interfaces for the service groups you are interested in. For WAAS, you use services 61 and 62 in opposite directions to perform load balancing appropriately.
A hint on your wccp on the 6500. Always configure redirect-in on the interfaces, L2-redirect and mask-assign to keep the traffic processed in hardware.
Here is a link on configuring WCCP for WAAS (which I assume you are deploying).
Hope that helps,
Dan

Similar Messages

  • WAAS using WCCP with gre tunnel going via vpn

    Hello All
    I am trying to get WAAS using WCCP to work according to the attached diagram. I would like to know if there is a redirection config that I need to apply to the ASAs?
    Many thanks
    Donagh

    Hello
    Thanks for your reply.
    I posted this twice in error.
    Original is here
    http://preview.tinyurl.com/ygpuehy
    You might have a look and see if you agree. I have not deployed yet.
    Thanks
    Donagh

  • Using WCCP on a corporate network

    I am wanting to know if it is possible to use WCCP within my corporate network. I have some Bluecoat Port 80 devices on each site, and one in a DMZ. I also have a 6509s with MSFCs on each site. Would it be easier to use WCCP or just the advanced forwarding options offered within the Bluecoat configuration. Anyone with experience of this? Any replies much appreciated in advance.

    for the bluecoat devices in each building, how do you intercept the traffic ?
    Are you using them as proxy ?
    With what you described, I would suggest to use wccp on the router in each building. Each router will intercept the web traffic and redirect it to its local BlueCoat.
    The local BlueCoat can then contact the central Bluecoat device using the advanced forwarding option just like you're doing now.
    You can upload a topology diagram and more information in ftp://ftp-sj.cisco.com/incoming. Then, post a message with the filename and I'll be able to retrieve it.
    From there I can better assist you with the wccp implementation.
    Regards,
    Gilles.

  • WAAS and WCCP question

    Is it possible to transition between two different WAAS appliances if using WCCP redirection? Currently I'm using a WAVE 274 and want to migrate to a recently installed NM-WAE-522.  WCCP is currently being used to redirect traffic to the WAVE.  Can I simply add the WAE to the WCCP config and then remove the WAVE?

    Does it matter that they are in the same subnet or not? The NM-WAE-522 is obviously on the same subnet as one of the router interfaces, but the WAVE-274 is actually on a different subnet off of our 6509.  I thought I remembered reading that it was at least recommended that WCCP devices be on the same subnet for load balancing, but I'm guessing it doesn't matter as I'm using L3 GRE redirection.

  • WAAS and WCCP

    Hello ,
    I have many Qs regarding the WAAS implemntation
    1- which better , using inline card or wccp and why ( is there any problem with inline cards ?)
    2- if we have ASA in the network , is there any os version required for the ASA to support tha WAAS, we have impelmnted the waas with wccp between 2 branches, all traffic optimized but there is 2 applications blocked ( not working at all ) , the 2 applications passing via Firewall is there any known reason for that ?
    3- we have cat4500 and it should support wccp to redirect traffic for WAAS , but redirect list is not supported at all, do you know if that for all 4500 platform or for just specific OS or Sup as nothing clear on Cisco regarding this point ( wccp redirect list ).
    Thanks
    Moamen

    Hey Moamen,
    1. I would not say either is better, but there are different applications. Where you need more then a single WAE for scaling and redundancy, I would recommend WCCP. Where you have fairly simple topology, requirements for only one WAE, and/or non-Cisco gear, I would probably recommend In-line. I've done ton's of both and both work really well for interception.
    2. ASA do have a minimum recommend code version. For interoperability with WAAS, you need Cisco ASA/PIX version 7.2.3 or later. In that version, there is the command "inspect waas" to allow for the sequence number jump in optimized traffic, which is why your ASA is blocking the traffic.
    3. The CAT4500 can support WCCP in hardware. The platform hardware only supports ingress interception, L2-redirect, L2-return, mask-assign configs on the WAE and the minimum IOS version I would recommend running would be 12.2(40)SG or later. As you mentioned, there are limitations with the redirect lists, they are NOT supported in any version of IOS, it's a function of the hardware. If you need to exclude traffic, you might want to consider using application policies when using CAT-4500.
    I hope that helps you out.
    Dan

  • Waas mode wccp to inline ?

    Hi
    On the center side we want to use wccp mode, on the branch side we want to use inline mode. Is that possible? Are there any cons for that?

    Hi Robbin,
    Thanks for answering the question.
    Now about youyr issue on "bringing down the site with failed WAE", please make sure that you follow the cabling rules mentioned here. THis is a critical piece of information to make sure the connectivity restores to normal after failover on inline interfaces.
    http://www.cisco.com/en/US/docs/app_ntwk_services/waas/wae/module/inline/installation/guide/17880fru.html#wp39911
    I am sure above should tke care of failover during such outage.
    Regards.

  • How to use attributes from different context nodes in one view?

    I am VERY new to the concept of CRM and currently working on creating an alternate version of the BP_HEAD_SEARCH. With help from SAPPRESSs book 'SAP CRM Web Client' i was ble to create my own simple Z-component.
    However after going back and forth the book and the forum (including this [article|https://wiki.sdn.sap.com/wiki/display/CRM/Howtoaddanexistingfieldtoasearchpageofadifferent+component]) i was not able to find a solution to my problem. My current search uses BuilHeaderAdvancedSearch as context node for searching. But the search should also be able to use attributes from BuilActivity, which is directly related to BuilHeader. I can't seem to find a way to get attributes from BuilActivity into the search window of my component without having to change SAP-Standard.
    Is this really the only way? Please advise on possible code and insertion point.

    Any suggestions?

  • My serial number for Logic Studio doesn't work. I used one from a different box and it worked. How can I get a new number?

    My serial number for Logic Studio doesn't work. I used one from a different box and it worked. How can I get a new number?

    http://support.apple.com/kb/TS2005
    http://support.apple.com/kb/HT1861
    https://ssl.apple.com/support/proapps/serialnumbers/

  • I cannot send email over 3G. Receiving email is ok. Using wifi from my landfibre allows me to send email. No idea where to find the solution. Suggestions please. Thanks ia

    I cannot send email over 3G. receiving email over 3G is ok. Using wifi from my landline (glass) is ok. No idea where to find the solution. Suggestions please. Thanks i.a.
    TheOne

    You need a DATA service enabled by your carrier to be able to send e-mail via thier network.  Do you have a data plan with your carrier ?  If so - is it enabled ?
    Can you access internet thru your network (not wifi) ?

  • From two given tables, how do you fetch the values from two columns using values from one column(get values from col.A if col.A is not null and get values from col.B if col.A is null)?

    From two given tables, how do you fetch the values from two columns using values from one column(get values from col.A if col.A is not null and get values from col.B if col.A is null)?

    Hi,
    Use NVL or COALESCE:
    NVL (col_a, col_b)
    Returns col_a if col_a is not NULL; otherwise, it returns col_b.
    Col_a and col_b must have similar (if not identical) datatypes; for example, if col_a is a DATE, then col_b can be another DATE or it can be a TIMESTAMP, but it can't be a VARCHAR2.
    For more about NVL and COALESCE, see the SQL Language manual: http://docs.oracle.com/cd/E11882_01/server.112/e26088/functions119.htm#sthref1310
    I hope this answers your question.
    If not, post a little sample data (CREATE TABLE and INSERT statements, relevant columns only) for all tables involved, and also post the results you want from that data.
    Explain, using specific examples, how you get those results from that data.
    Always say which version of Oracle you're using (e.g., 11.2.0.2.0).
    See the forum FAQ: https://forums.oracle.com/message/9362002

  • How to Restore Full Offiline Backup using BRTOOLS from a Tape

    Dear all,
    I want to recover PRD Full Offline Backup using BRTOOLS from a tape in a new machine.
    I have Install SAP in the new machine.
    Now I want to restore the PRD Full Offiline Backup taken through BRTOOLs in tape in the new machine.
    1. I have shutdown the SAP.
    2. I have shutdown the database Oracle 10g.
    3. I have inserted the backup tape
    4. Through user ORASID I have executed BRTOOLS
    I got the following options: -
    BRTools main menu
    1 = Instance management
    2 - Space management
    3 - Segment management
    4 - Backup and database copy
    5 - Restore and recovery
    6 - Check and verification
    7 - Database statistics
    8 - Additional functions
    9 - Exit program
    I selected Option 5 Restore and recovery
    And got the Following Options
    Restore and recovery
    1 = Complete database recovery
    2 - Database point-in-time recovery
    3 - Tablespace point-in-time recovery
    4 - Whole database reset
    5 - Restore of individual backup files
    6 - Restore and application of archivelog files
    7 - Disaster recovery
    8 - Reset program status
    1. Now which option do I need to select and then what all other options do I need to select.
    2. Whether the database should be a mount state or shutdown ?
    Kindly help.

    Dear Mark,
    Thanks.
    As suggested I tried both the options however face some difficulties please suggest
                                       brrestore -u / -c -b <backup_log.ext> -p init<SID>.sap -m full
    hinrnddev:oradev 1> brrestore -u / -c -b bedflluv.fft -p initDEV.sap -m full
    BR0401I BRRESTORE 7.00 (32)
    BR0405I Start of file restore: redhafeh.rsb 2010-05-22 11.55.55
    BR0484I BRRESTORE log file: /oracle/DEV/sapbackup/redhafeh.rsb
    BR0252E Function fopen() failed for '/oracle/DEV/sapbackup/bedflluv.fft' at location BrbLogRead-1
    BR0253E errno 2: No such file or directory
    BR0121E Processing of log file /oracle/DEV/sapbackup/bedflluv.fft failed
    BR0406I End of file restore: redhafeh.rsb 2010-05-22 11.55.55
    BR0280I BRRESTORE time stamp: 2010-05-22 11.55.55
    BR0404I BRRESTORE terminated with errors
    When I used the brrestore command I got the above error message.
    Then I tried the next option Complete database recover
    BRRECOVER options for restore and recovery
    1 * Recovery type (type) ............. [complete]
    2 - BRRECOVER profile (profile) ...... [initDEV.sap]
    3 ~ BACKINT/Mount profile (parfile) .. []
    4 - Database user/password (user) .... [/]
    5 - Recovery interval (interval) ..... [30]
    6 - Confirmation mode (confirm) ...... [yes]
    7 - Scrolling line count (scroll) .... [20]
    8 - Message language (language) ...... [E]
    9 - BRRECOVER command line (command) . [-p initDEV.sap -t complete -i 30 -s 20 -l E]
    Standard keys: c - cont, b - back, s - stop, r - refr, h - help
    BR0662I Enter your choice:
    C
    Complete database recovery main menu
    1 = Check the status of database files
    2 * Select database backup
    3 * Restore data files
    4 * Restore and apply incremental backup
    5 * Restore and apply archivelog files
    6 * Open database and post-processing
    7 * Exit program
    8 - Reset program status
    Standard keys: c - cont, b - back, s - stop, r - refr, h - help
    BR0662I Enter your choice:
    C
    Complete database recovery main menu
    1 + Check the status of database files
    2 # Select database backup
    3 # Restore data files
    4 # Restore and apply incremental backup
    5 # Restore and apply archivelog files
    6 + Open database and post-processing
    7 = Exit program
    8 - Reset program status
    Standard keys: c - cont, b - back, s - stop, r - refr, h - help
    BR0662I Enter your choice:
    the + sign got changed to +
    and the * got changed to #
    then it is getting in loop please suggest what do I do now.

  • How to get useful data from request?

    Hello.
    I am looking for creating a management tool for a web site. All I want is that is there any ready to use API or package or open source project for retrieving user�s information? I just mean that is there any easy to use way in java to get useful data from a client (for example location, his or her system configuration and information �).
    Thanks.

    If you dump all the data from request (see the javadoc, and especially the "header methods" ) you'll see the data you can get are quite simple.
    The only thing you can try to rely on are ;
    - the IP address from the sender (when reversed to DNS, you can sometime use the tld to locate the country it comes from. Yet, you'll get many .com name, so it's not that significant. it may also give you the IAP used). Note that if the user is using a proxy, it's the proxy IP that you'll collect
    - the User-Agent header : from this, you can guess the OS and the browser used
    - the Referer header : usefull to get where your user comes from (where they found a link to your site)
    - the Cookie header : if you're using a servlet container with session id stored in cookie, you should see the Cookie header appear on the second request to your site. That helps finding out wether your user accep cookie or not (from a server point).
    Besides these, i don't think you can get any other useful data without asking your users on a form. Note that it's the client that decides to send Referer, User-Agent or Cookie headers. Those are not mandatory to the Http Protocole and some browser allow their user to fool their content (butmore than 90% of the widespread browsers don't)

  • Using MapViewer from PL/SQL vs Java

    Hi group!
    The MapViewer User's Guide has this to say about using MapViewer from PL/SQL:
    "The usage model for the SDO_MVCLIENT package is almost identical to that of
    MapViewer JavaBean-based API" etc etc .. "For usage and reference information about specific functions or procedures, see the description of the associated JavaBean-Based API. methods and interfaces in Chapter 4"
    If I don't misunderstand the basic concept, in a Java Web App (using the MapViewer Bean) you create a MapViewer object for each HTTP-user-session, like so:
    MapViewer mv = new MapViewer("http://my_corp.com:8888/mapviewer/omserver");
    ... which you would then store in the user's session object, so that the MapViewer Bean conveniently holds the map's state on the user's behalf.
    To do the equivalent in PL/SQL, the User's Guide suggests:
    "connect scott/tiger
    call sdo_mvclient.createmapviewerclient(
    'http://www.mycorp.com:8888/mapviewer/omserver') ;
    The preceding example creates, in the current session, a unique MapViewer client
    handle to the MapViewer service URL"
    Does "current session" refer to the HTTP-user-session? While I've used PL/SQL before, I've not used the PL/SQL Web Toolkit. Is the session handling implicit here (and invisible?) or should the sdo_mvclient be subsequently stored in the PL/SQL equivalent of a (J2EE) HttpSession object?
    YT

    Part of the answer will depend on how you plan to deploy the application. If you have a few, local clients you could go with the traditional client/server model. If you have a lot of clients and/or they are spread out over a relatively large area (like a campus setting), a web front-end will save you a lot of hassels down the road when it comes time to upgrade.
    Regardless of the the front end, I can tell you that I have been greatly impressed with the throughput you can get by moving most of the code to PL/SQL packages. A few years ago we reworked a VB/Oracle app by moving a lot of the code out of VB and into packages, leaving the client to essentially call procedures and format the output. We had more than a 3x performance increase on the same hardware and our network utilization decreased noticably.
    I am now in the process of replacing the client code with Java servlets/JSP, primarily because of the maintenance hassles I mentioned earlier. There are some limitations with an HTML page but most of these have been cosmetic so far.
    We are still relying heavily on PL/SQL packages. The servlet code basically gets a request, calls a package to get the data, then hands the results to a JSP page. The JSP then formats the output and sends it to the client. We are little more than halfway through the re-write, but it appears performance will increase again. Not as noticably as before, but I will take what I can get. As you have seen, once something is rolled out it always ends up getting used more than you anticipated. Better to over-engineer now than have to patch it once it is live.
    HTH

  • Is there a way to use music from multiple users itunes libraries on one iMac for a slideshow in Aperture?

    I am trying to put together a slide show for a trip my wife and I took to England. I would like to be able to use music from both our itunes libraries in the slide show. I am using Aperture to create the slide show since it seems to be more versatile than iPhoto for this. Only trouble is that when I log into my username on the iMac I only see my iTunes library and similar when logging into her username. We have different music but would like to use some from each library in the slide show.

    You can only use one library at a time in an Aperture slideshow, so I'd suggest to simply collect the audio that you want to use in a folder (export the songs from both iTunes Libraries) and then import this folder to Aperture. Now you have a project containing the audio files; you will see it in the Aperture Audio section of the audio Browser, right above the iTunes section.
    You can use the Apperture audio just like the audio in iTunes to drag to the timeline of your slideshow.
    Regards
    Léonie

  • How to use data from standard view in Web dynpro for ABAP

    Hello:
    I have to create an Abap Web Dynpro, and I must use data from a standard view in the new one. Does anybody know what do I have to do?
    Thank you and have a happy new year.

    Hi Rodrigo,
    Firstly, list the Standard component under Component Usage of the Component which you are creating in your View.
    Second, In the Custom Component, view, goto context, and try to add the node from the Standard component in to your view.
    NOTE: The second step requires a Node in component controller of the Standard Component.
    Finally, Now in your view, get the data from that and map the data.
    NOTE: To do this, I think you need to call your Standard WDA first and then only your node contains data and it will be passed.
    I hope it is helpful.
    Regards,
    Shashikanth. D

Maybe you are looking for