WAE-674 as a Content Engine

Dear All Experties,
We are using a Cisco Content engine 7325 as a proxy server.recently we brough WAE-674 as a replacement of these old content engine.After turn on WAE-674,Blue screen pop up on moniter.I am not able to access anything with GUI as well through command line.That why i am not able to configure that one.
Please advise me if anybody else also faced this problem or if anybody have any idea what i can do ???
Thanks in advance

Hi,
How are you connected to the WAE?
If you are directly connected to the WAE through a screen/keyboard, what you see might be expected: the WAAS/ACNS software stop redirecting it's console output on the screen after booting it's kernel and move it to the serial port.
This is explained in the hardware specs of your device:
You can connect a keyboard to any USB port and connect a monitor to the video connector to troubleshoot the BIOS boot process. However, video output is for troubleshooting only during the BIOS boot process. The video output stops displaying when the serial port becomes active. To monitor the boot process in normal operation, use the serial console port.
http://www.cisco.com/en/US/partner/docs/app_ntwk_services/waas/wae/installation/7341-7371/guide/7300intr.html#wp1040565
Could you have a look at the boot sequence from the serial port and see if everything looks fine from there?
Regards,
Nicolas

Similar Messages

WAE 674 multipurpose

HI there,
I have configured Cisco WAE 674 as Content Engine conntected with Websense Server for filtering.Can I use the same device also as WAAS and configure WCCP ?
thanks a lot!

Hi ,
Yes you can use the 674 as either WAAS device or content engine. To do this you need to use the CD recovery procedure in formating the flash,disk and installing the WAAS IOS image.
If you have WAAS recovery CD then run these steps:
2,3,5,7,8, remove the CD from the CD Drive and 9
Regards,
Bala

Content Engine + Barracuda Spyware firewall (transparent/intercept proxies)

Hello all.
We are trying to get our WAE-511 content engine and our Barracuda Spyware Firewall 310 to work together.
It seems they interfere with each other because they are both transparent (intercept?) proxies.
What would need to be done/configured (preferably in the Cisco CE) to make the two devices work together?
Would shifting the CE to non-transparent mode help?

check out the following link, hope this helps :
http://www.cisco.com/en/US/products/ps6469/products_user_guide_chapter09186a00804a16ab.html

Content Engine compatability with Windows Media Player

I am currently running ACNS version 5.5 on our CE510 Content Engine. We want to set this box up to serve VOD requests from WMT. I think the clients on site are all using Windows Media Player version 10. Does this version of ACNS software work with Windows Media Player 10?

Dan
this brings up an interesting point. The content (which is canned Video on an Intranet Web site) is HTTP? I am wasting my time here by trying to use the Windows MP services?? Perhaps I already have what I need...
Your comments appreciated.
Kevin

Should the Cisco Content Engines be used as a proxy appliance

Should the Cisco Content Engine be use as a proxy appliance like a Blue Coat appliance, Squid cache engine, ISA server, etc...
I am pretty sure it is but just need some feedback on past experiences. Customer would like to by a Cisco product for Web filtering/proxy.
or is it strictly used to help with web base applications.

HI,
the CE is basically able to check every request it supports. If you are using 3rd level products like smartfilter, websense or webwasher you can use the features of those products to supress/forbid certain requests(i.e MSN etc.)
Kind Regards,
Joerg

Help!!! Content engine

my configuration is follow the attached file. I don't know what is wrong with my content engine using as a cache server. when i connect this CE to my network, i can make my user access to the internet fast only 2 days, but after 2 days it makes my users internet connection slow. So when users access to the internet slow, i disconnect this CE from my network, then my users internet connections is running better. So please help me to find what is incorrect with my configuration and what commands i should add more to this current configuration"

What is the ACNS software version u r using in ur content Engine7305.I am sending u a configuration doc for ACNS rlease 5.2.This has all the info regarding ACNS 5.2.
http://www.cisco.com/en/US/products/sw/conntsw/ps491/products_configuration_guide_book09186a00802debd6.html
Let me know, if you have any problem in browsing this big document. and finding out the pblm.I will assist you.

Content Engine NM ACNS/network access

After searching Google and Cisco, here's my setup...
2851 Router running 15.1T
CE-NM-BP-80G-K9 in slot 1/0
Bridge group 1 for LAN and Wireless WIC.
Goal: Either add the external CE interface to the LAN on the bridge group or use WCCP to cache traffic through the internal interface.
I was able to access ACNS once, but I'm completely new to the design and it was only for testing with the IP scheme. I reset the config, reloaded the router and now I can't access ACNS via the web gui nor can I access the network from the CE (ping or ftp).
Interface ContentEngine 1/0 Config:
     ip address 10.0.0.1 255.255.255.0
     Service Module ip address 10.0.0.2 255.255.255.0
     Service Module external ip address 10.0.1.1 255.255.255.0
     Service Module ip default gateway 10.0.0.1
Interface BVI1
     ip address 192.168.2.1 255.255.255.0
     using dhcp etc
Service module config:
CE#sh run
! ACNS version 5.5.3
hostname CE
http proxy incoming 80 8080
ip domain-name mydomain.com
interface FastEthernet external
exit
interface FastEthernet internal
exit
wmt evaluate
wmt accept-license-agreement
wmt enable
ip name-server 8.8.8.8
ip name-server 192.168.2.1
wccp router-list 1 192.168.2.1
wccp web-cache router-list-num 1
wccp reverse-proxy router-list-num 1
wccp wmt router-list-num 1
wccp version 2
username admin password 1 xxx
username admin privilege 15
username xxxx password 1 xxx uid 2001
username xxxx privilege 15
authentication login local enable primary
authentication configuration local enable primary
cdm ip 192.168.2.1
! End of ACNS configuration
Here's what I get when attempting to ping:
CE#ping 192.168.2.1
connect: Network is unreachable
CE#ping 10.0.0.1
connect: Network is unreachable
CE#ping 10.0.1.1
connect: Network is unreachable
And from the LAN:
seth@Sony:~$ ping 192.168.2.1
PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
64 bytes from 192.168.2.1: icmp_req=1 ttl=255 time=1.79 ms
^C
--- 192.168.2.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 1.799/1.799/1.799/0.000 ms
seth@Sony:~$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
64 bytes from 10.0.0.1: icmp_req=1 ttl=255 time=1.39 ms
64 bytes from 10.0.0.1: icmp_req=2 ttl=255 time=1.93 ms
^C
--- 10.0.0.1 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 1.396/1.666/1.936/0.270 ms
seth@Sony:~$ ping 10.0.0.2
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
^C
--- 10.0.0.2 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 1006ms
seth@Sony:~$ ping 10.0.1.1
PING 10.0.1.1 (10.0.1.1) 56(84) bytes of data.
^C
--- 10.0.1.1 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 1007ms
Page cannot be displayed when attempting to hit the CE on port 8001 or securely at 8003 although the CE shows it's listening
CE#sh gui-server
GUI Server is enabled
Listen on port 8001
Secured GUI Server is enabled
Secured GUI Listen on port 8003
Let me know if there's some other pertinent info, but what am I missing?

SOLVED --
The mistake was my own...in writing this post and re-testing, I realized I had made a foolish mistake. I applied an access-list (which I forgot to include) to the "ip wccp web-cache redirect-list bypass_content_engine" in the global config of the router.
When I installed service 95 for spoofing, I automatically added the same access list to it as well.
This was not a good thing since the access list denied packets with a destination of our internal IP addresses from going through the content engine. This worked fine on the way *out* of the router. But as the now-spoofed packets returned, their destination was an inside IP address and they were pretty much discarded. Foolish Mistake!
Removing the ACL from the "ip wccp 95" statement in the global config fixed the issue and I am spoofing fine.
Sorry to waste time...
David Hunter

Content Engine Problem

Dear All,
My apologies if this posting is on the wrong board.
I've a problem with our content engine returning an error of:
"Tre reply from server is not valid"
The URL of the site is http://hiring.monster.co.uk/jobs/createtitle.aspx?mode=qb.
I've attached a screenshot of the error message.
Any advice or help would be greatly appreciated.
Thank you in advance.
Sinh

This symptom is observed on a router on which Web Cache
Communication Protocol (WCCP) is enabled and Cisco Express Forwarding (CEF)
switching is disabled. If the caches are Cisco caches, they will be running
software prior to ACNS 4.2.5.
solution: Ensure that CEF switching is enabled on the router. If this is not possible, the impact of the problem on the cache will be minimized if the authentication bypass function is disabled.also try upgrading IOS to 12.1(18.01)E which may solve the issue.

Content Engine Module is logging DHCP errors

Content Engine Module in Cisco 3725 is logging the following eror continously:
Sep 29 16:47:50 ContentEngine dhclient: %CE-DHCP-5-191000: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
Sep 29 16:47:54 ContentEngine dhclient: %CE-DHCP-5-191000: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
Sep 29 16:47:58 ContentEngine smartd: %CE-SMARTD-3-435000: No Errors Logged
Sep 29 16:48:05 ContentEngine dhclient: %CE-DHCP-5-191000: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 1
Sep 29 16:48:06 ContentEngine dhclient: %CE-DHCP-5-191000: No DHCPOFFERS received.
Sep 29 16:48:06 ContentEngine dhclient: %CE-DHCP-5-191000: No working leases in persistent database - sleeping.
Sep 29 16:48:06 ContentEngine %CE-DHCP-5-191000: Script called with reason: FAIL
Sep 29 16:52:58 ContentEngine smartd: %CE-SMARTD-3-435000: No Errors Logged
Disable the external interface (shutdown) didn't fix the problem:
Sep 29 17:02:05 ContentEngine dhclient: %CE-DHCP-5-191000: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
Sep 29 17:02:05 ContentEngine dhclient: %CE-DHCP-3-191000: send_packet: Network is down
Sep 29 17:02:08 ContentEngine dhclient: %CE-DHCP-5-191000: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
Sep 29 17:02:08 ContentEngine dhclient: %CE-DHCP-3-191000: send_packet: Network is down
Sep 29 17:02:11 ContentEngine dhclient: %CE-DHCP-5-191000: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
Sep 29 17:02:11 ContentEngine dhclient: %CE-DHCP-3-191000: send_packet: Network is down
Sep 29 17:02:16 ContentEngine dhclient: %CE-DHCP-5-191000: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
Sep 29 17:02:16 ContentEngine dhclient: %CE-DHCP-3-191000: send_packet: Network is down
Sep 29 17:02:21 ContentEngine dhclient: %CE-DHCP-5-191000: No DHCPOFFERS received.
Sep 29 17:02:21 ContentEngine dhclient: %CE-DHCP-5-191000: No working leases in persistent database - sleeping.
Sep 29 17:02:21 ContentEngine %CE-DHCP-5-191000: Script called with reason: FAIL
Sep 29 17:02:58 ContentEngine smartd: %CE-SMARTD-3-435000: No Errors Logged
Any ideas how to fix this problem ?

Try the global command:
ce(config)# no auto-register enable
http://www.cisco.com/univercd/cc/td/doc/product/webscale/uce/acns53/53cref/6812ref.htm#wp1038726

Content Engine transaction logs -- monitoring and analysis

At our remote sites there's a local Cisco CE511 to ease our WAN bandwidth. I have been tasked to find a method to gather CE usage for trending and troubleshooting.
From my search on the internet I decided to go with the Webalizer application. I setup the CEs to export their transaction logs every hour to my FTP server. After a test of Webalizer on a log file, it produced a nice HTML report for that hour.
I would like to discuss with anyone on bringing this up to a new level. I would like webalizer to run as a cron job, but the log file names changes every hour. So that's a hurdle I need to figure out. Also keeping track of user web hits is important. I would like to make sure my reports are accurate in reporting what IP address is the top talker.
I hope this will start a productive exchange of ideas. Thanks.

Simple Network Management Protocol (SNMP) is an interoperable standards-based protocol that allows for external monitoring of the Content Engine through an SNMP agent.
An SNMP-managed network consists of three primary components: managed devices, agents, and management systems. A managed device is a network node that contains an SNMP agent and resides on a managed network. Managed devices collect and store management information and use SNMP to make this information available to management systems that use SNMP. Managed devices include routers, access servers, switches, bridges, hubs, computer hosts, and printers.
An SNMP agent is a software module that resides in a managed device. An agent has local knowledge of management information and translates that information into a form compatible with SNMP. The SNMP agent gathers data from the Management Information Base (MIB), which is the repository for information about device parameters and network data. The agent can also send traps, or notification of certain events, to the manager.
http://www.cisco.com/en/US/products/sw/conntsw/ps491/products_configuration_guide_chapter09186a0080236630.html#wp1101506

Should the Content Engine work while the Inernet link is down ?

I have installed CE590 in a client network
The http saving performance is from 30 : 40 %
My client want to make sure the CE is caching the web site
He want to shutdown Serial port of the main router , and try to browse web sites. ( the Cached sites )
Should he get a reply from the CE and browse the cached sites ??
I mean , Can the PC browser ( while the internet is link is down ) open page like www.yahoo.com for example if it is cached on the CE ??
Is there is any command of the CE that can display the name of the cahced web pages ?
Note : Cisco Content Engine Software Release 3.11
Can anyone help me ?
Thanks
Mohamed Abdallah

Mohamed,
Before you go any futher you need to upgrade the CE to ACNS 4.2.3. There are known issues with 3.1.1.
To answer your question the CE will only server content if it can not access the internet if the object is fresh. By this I mean the object has not expired or the object does not need revalidation eg If modified since request.
This could cause problems with broken pages etc etc.
Your best option is to turn on transaction logging.
transaction-logs enable
You can then go to the local1/logs directory on the CE
type working.log
This will show you the urls that clients are requesting and if they got a hit / miss/ ims hit / ims miss etc etc.
Overall your cache should always have access to the origin server for content.
Cheers
Phil

Content Engine caching video content?

I am currently running ACNS version 5.5.11.2 on a CE510 Content Engine. I recently had to replace the unit and when I set up the partitions for the new build, I elected to go with CE510#disk config sysfs 10% cfs 45% mediafs 45%.
Before the cfs was setup to use the whole box. I was thinking that the mediafs partition would start to cache video content. Does that happen automatically or is there some other setting to make that happen further. How do I determine if it is getting any use?

A content engine can cache files transfered via ftp but not https [as the content is encrypted].
It can cache whatever file, including video, audio, ...
Content routing, content switching are just names.
They refer to how the traffic will be intercepted and forwarded to the content engine.
You could simply use a proxy solution and have your users setup their browser to use the content engine as a proxy, or you could transparently intercept http/ftp traffic via a router running wccp, or you could use a Layer7 device like a CSS to intercept the traffic and redirect to the content engine.
Regards,
Gilles.

Content Engine Network Module for Caching File Server Objects

We have a content engine network module for a 2821 router located at a branch office that we'd like to use for clients to obtain locally cached file objects from a Windos server located at our headquarters or corporate office. I've been looking for some sample configs or documentation that will show me that this is possible and on how to do it since this is my first time ever doing. All I was able to find so far was the link below under "Support of Preloading of NTLM Authenticated Objects", but it seems incomplete in providing configuration tasks that most CCO doc's usually provide. Has anyone else had any luck finding some useful doc's or sample configs to get this accomplish? Thanks in advance.
http://www.cisco.com/univercd/cc/td/doc/product/webscale/uce/acns55/55ldg/urlfiltr.htm#wp1158213

You can't cache Windows Files using the Cache Engines.
You CAN do this using WAFS though. I'd suggest looking at the WAFS (or upcoming WAAS) products, which use WCCP like the Cache Engines to transparently redirect Windows File Sharing requests.

Content Engine CE565 authentication cache

I have a Content Engine CE565 running software version CE 5.1.7
The commands <show users request-authenticated> and <show http-authcache> provide me with information on authenticated users, but I would like to know how to determine the time remaining for a user/ip address in the authcache. This is with the understanding that the authentication will timeout after the configured period of inactivity (in minutes).
Also, is there a way to remove the authentication cached for single user/ip address? Understanding that the authentication cache resides in RAM. The only command that I am aware of is <clear users request-authenticated>, which clears all authenticated users. However, this requires all users to reauthenticate. TIA

As far as I know, there is no way to clear a single user, only all of them by using the command you mentioned above. The command http authentication cache timeout can be used to configure the time between last access and cache removal.

Content Engine errors.

Hi there,
I'm having some problems with Content Engine.
I would appreciate any help.
It gives following errors:
Jun 12 08:15:59 CE01 wccp: %CE-WCCP-5-500008: WCCP: A new view from
the 25.25.25.25. Change number = 28
Jun 12 08:15:59 CE01 wccp: %CE-WCCP-5-500014: WCCP: New CE notified of
15.16.17.208
Jun 12 08:15:59 CE01 wccp: %CE-WCCP-5-500026: New CE entry being
created for 15.16.17.208 seen by router 25.25.25.25
Jun 12 08:16:07 CE01 wccp: %CE-WCCP-4-500015: WCCP:No assignment sent:
15.16.17.204 not in Router View
Jun 12 08:16:08 CE01 wccp: %CE-WCCP-5-500008: WCCP: A new view from
the 25.25.25.25. Change number = 29
Jun 12 08:16:08 CE01 wccp: %CE-WCCP-5-500014: WCCP: New CE notified of
15.16.17.204
Jun 12 08:16:08 CE01 wccp: %CE-WCCP-5-500026: New CE entry being
created for 15.16.17.204 seen by router 25.25.25.25
Jun 12 08:16:17 CE01 wccp: %CE-WCCP-5-500019: WCCP: New WC in compute
assign 15.16.17.204
Jun 12 08:16:40 CE01 wccp: %CE-WCCP-3-500001: HTTP Proxy may be down,
keepalives halted!
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct got error :
50 for key stat/cache/http/perf/throughput/requests/sum connection 5
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct: unable to
get `stat/cache/http/perf/throughput/requests/sum' from dataserver
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: unable to get http
request throughput stats(error 50)
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct got error :
4 for key stat/cache/https/request connection 5
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct: unable to
get `stat/cache/https/request' from dataserver
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: unable to get https
request throughput stats(error 4)
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct got error :
4 for key stat/cache/ftp connection 5
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct: unable to
get `stat/cache/ftp' from dataserver
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: unable to get
ftp-over-http request throughput stats(error 4)
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct got error :
4 for key stat/cache/http/usage/cpu/sum connection 5
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct: unable to
get `stat/cache/http/usage/cpu/sum' from dataserver
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: unable to get cpu
stats(error 4)

Hi guys,
I am really out of ideas!!!
I've updated software couple times already.
but nothing helps.
it still gives same error:
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/http/usage/cpu/sum not found not found in dataserver
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/http/request not found not found in dataserver
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/https/request not found not found in dataserver
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/https/requests not found not found in dataserver
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/ftp-native not found not found in dataserver
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/ftp not found not found in dataserver
Jun 16 14:23:02 ponent exec_show_stats: %CE-CLI-3-170013: item stat/wccp/bypass not found not found in dataserver
Jun 16 14:23:02 ponent exec_show_stats: %CE-CLI-3-170013: item stat/wccp/bypass not found not found in dataserver
Jun 16 14:23:52 ponent exec_rule: %CE-CLI-3-170013: Verifier not responding. when setting cfg/gl/cache/rule/stat/show (Error number: 32)
Jun 16 14:23:52 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/http/err not found not found in dataserver
Jun 16 14:23:52 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/https/err not found not found in dataserver
Jun 16 14:24:37 ponent cfg_bin_urlfilter: %CE-CLI-3-170013: Verifier didn't respond. Need to re-register verifier. when setting /cfg/gl/cache/urlfilter/http/enable (Error number: 64)
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct got error : 4 for key stat/cache/http/perf/throughput/requests/sum connection 5
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct: unable to get `stat/cache/http/perf/throughput/requests/sum' from dataserver
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: unable to get http request throughput stats(error 4)
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct got error : 4 for key stat/cache/https/request connection 5
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct: unable to get `stat/cache/https/request' from dataserver
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: unable to get https request throughput stats(error 4)
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct got error : 4 for key stat/cache/ftp connection 5
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct: unable to get `stat/cache/ftp' from dataserver
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: unable to get ftp-over-http request throughput stats(error 4)
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct got error : 4 for key stat/cache/http/usage/cpu/sum connection 5
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct: unable to get `stat/cache/http/usage/cpu/sum' from dataserver
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: unable to get cpu stats(error 4)
Jun 16 14:24:47 ponent java: %CE-CMS-4-700001: ds_getStruct got error : 4 for key stat/cache/http/perf/throughput/requests/sum connection 5
Jun 16 14:24:47 ponent java: %CE-CMS-4-700001: ds_getStruct: unable to get `stat/cache/http/perf/throughput/requests/sum' from dataserver
Jun 16 14:24:47 ponent java: %CE-CMS-4-700001: unable to get http request throughput stats(error 4)
Jun 16 14:25:15 ponent cfg_bin_urlfilter: %CE-CLI-3-170013: Verifier didn't respond. Need to re-register verifier. when setting /cfg/gl/cache/urlfilter/http/enable (Error number: 64)
Jun 16 14:25:24 ponent writemem.sh: %CE-CLI-2-170054: running-config has 0 line(s)
Jun 16 14:25:24 ponent exec_copy: %CE-CLI-3-170055: Copy running-config to startup-config failed!. status(1.20)
please, any suggestion would be appreciated.

WAE-674 as a Content Engine

Similar Messages

Maybe you are looking for