WAE-674 not retaining network settings when configured using recovery CD

WAE-674 Issues
Here is the story so far:
Disks crashed. Installed new disks. Inserted the recovery CD. wiped disks and installed .bin image. tried to configure network settings. No error message but interface settings did not stick. I am 100% positive that the network settings were correct. cannot connect to the device via telnet. Can see the device with CDP but no IP address configured.
                Device ID: NO-HOSTNAME
                Entry address(es):
                Platform: OE674, Capabilities: Host
                Interface: GigabitEthernet1/0/23, Port ID (outgoing port): GigabitEthernet 1/0
                Holdtime : 137 sec
                Version :
                Cisco Wide Area Application Services Software
                Copyright (c) 1999-2013 by Cisco Systems, Inc.
                Cisco Wide Area Application Services Software Software Release 5.3.3 (build b6 Sep 27 2013)
                Version: oe674-5.3.3.6
Could I be having these issues because I am using a monitor and keyboard not a console cable?
Old style console cable not available. equipment is difficult to procure because I'm in the middle of nowhere.
Could the issues be because of the 64bit architecture of WAE-674 i.e could I be using the wrong recovery disk?
Attached are images of the device booting when recovery CD is not inside the device.

Hi Kristof,
The problem is that as soon as the serial port becomes active, the device stops displaying the output to the screen/keyboard so you'll really need an "old style" console cable to see what is really happening with your device.
More info: http://www.cisco.com/c/en/us/td/docs/app_ntwk_services/waas/wae/installation/7341-7371/guide/7341gd/7300intr.html#wp1040804
You can connect a keyboard to any USB port and connect a monitor to the video connector to troubleshoot the BIOS boot process. However, video output is for troubleshooting only during the BIOS boot process. The video output stops displaying when the serial port becomes active. To monitor the boot process in normal operation, use the serial console port.
The Serial Attached SCSI (SAS) connector is not supported.
The systems-management Ethernet connector is not supported.
Nicolas

Similar Messages

ITunes does NOT detect network connection when I use a 3G modem

Hi
since christmas iTunes has not been able to update when i commute, using a 3G USB modem. Over enabled and live WLAN or Ethernet interfaces everything works fine, but TCPdump does not register any packets at all from iTunes when only the USB 3G modem is up. All other networking activities work in this state, but iTunes erronously thinks there is no network and doesn't even initiate network activity.
Seems iTunes tries to be smart by detecting "is there network" by asking something in the OS, rather than trying?
Is this a bug? Am I the only one experiencing this? Is this isolated to my particular 3G modem/ISP? I don't think so...
thanks for any enlightenment,
peter

Hi. Just go a bit further by process of elimination which you've already started. Here's a couple more things you can try.
1. Different USB cable?
2. Try plugging into another computer just to see if your iPhone will get recognised then.
If it still deosn't work then I can only assume that the handset itself has developed some kind of fault, in which case, just book a 'Genius' appointment at your local Apple store asap and get it replaced.

DHCP snap-in will not retain window settings, columns, etc.

DHCP (version 6.3) will not retain window settings or columns after being closed. I haven't been able to find any information on this so far. Has anyone else had this issue?

Hi,
I understand your issue. The DHCP management console won't save the view customize settings.
We could customize the DHCP management console using MMC (Microsoft Management console)snap-in, customize it and save it to a place. Doing this makes the console remembered the configuration.
More information regarding MMC, please take a look at the below link:
Microsoft Management Console 3.0
For the DHCP management console does not remember the customization, this might by design. If we want to make a customized DHCP console shortcut, we could take a try to enter DHCP in author mode, more detailed steps, please take a check with the post of
Josh in the below thread:
DHCPMGMT.MSC in Remote Server
Administration Tools (RSAT) won't remember DHCP server
Hope this may help
Best regards
Michael Shao
TechNet Community Support

I am trying to install a second airport express to extend my network. When I use the aiport utility it does not see the second airport express.

I am trying to install a second airport express to extend my network. When I use the aiport utility it does not see the second airport express.

Suggest that you perform a Factory Default Reset as follows:
Pull the Express from power
Wait a few moments
Hold in the reset button and keep holding it an additonal 8-10 seconds while you plug the Express back in to power
Release the reset button and allow 40-45 seconds for the Express to restart
Apple's instructions to do what you want are here:
It will often help to temporarily connect an Ethernet cable from your Mac to the AirPort Express for the setup. Once the Express is configured, you can disconnect the Ethernet cable and move the Express to the desired location.
http://support.apple.com/kb/HT4259
Although an AirPort Extreme is shown as the extending device in the example, the setup for an AirPort Express is exactly the same

I hit Forget Network and now cannot get back onto my wireless home network. All of my other computers and iphones are fine. How do I get the network back? It shows in my list of networks but when I use the password and try to join it says not connected.

I hit Forget Network and now cannot get back onto my wireless home network. All of my other computers and iphones are fine. How do I get the network back? It shows in my list of networks but when I use the password and try to join it says not connected.

See if the iPad will accept the password after you restart it. It's worth a try.
Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
You could also try a reset as well.
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.

Firefox 29.0.1 Does Not Retain Options Settings. Cookies Enabled.

On only one of my XP profiles, Firefox 29.0.1 does not retain the settings made under tools-options. I have deleted the cookies from Mozilla on the chance they may have been corrupted and have also cleared the web cache. The problem remains. Also, it is not clear in the new version how to have Firefox ask you each time before a cookie is accepted. Thanks for you help.

You can try to delete the cookies.sqlite and permissions.sqlite files in the Firefox profile folder.
You can use this button to go to the currently used Firefox profile folder:
* Help > Troubleshooting Information > Profile Director: Show Folder (Linux: Open Director; Mac: Show in Finder)
* http://kb.mozillazine.org/Profile_folder_-_Firefox
You can inspect and manage the permissions for the domain in the currently selected tab via these steps:
* Click the "Site Identity Button" (globe/padlock) on the location bar
* Click "More Information" to open "Tools > Page Info" with the Security tab selected
* Go to the Permissions tab (Tools > Page Info > Permissions) to check the permissions for the domain in the currently selected tab
Also see:
[[Cookies - Information that websites store on your computer]]
[[Permissions Manager - Give certain websites the ability to store passwords, set cookies and more]]

Please make sure your network settings are configured correctly pes 2013

how to fix please make sure your network settings are configured correctly pes 2013

Erm I'm guessing the PES13 PS3 servers were turned off yonks ago..?

Same thing is happening to me. Adobe has not responded to anyone about this error. It appears that Abobe XI is not compatible with IE 11. I do not get this error when I use Chrome or Firefox. Only IE 11 does this. I have tried clearing cache and cookies.

Same thing is happening to me. Adobe has not responded to anyone about this error. It appears that Abobe XI is not compatible with IE 11. I do not get this error when I use Chrome or Firefox. Only IE 11 does this. I have tried clearing cache and cookies. I even uninstalled and re-installed IE 11. It is still doing it. I am surprized that a company like Adobe would just ignore our posts and leave us hanging this this.
Error message is FAILED TO GET DISPATCH FROM IBRWSR2. Then when you click on it the next error message says: PHTML IS NULL. You have to click this error message twice and then the PDF finally loads. Happened every time
Does anyone have a solution since Adobe will not respond?
As a last resort I will try uninstalling the Adobe Reader XI and install Adobe Reader 10 instead. It seems to work ok. But when I try to install version 10 the Adobe site tries to install XI. Any ideas?
JimP08758

It worked just fine for me.
Many site issues can be caused by corrupt cookies or cache.
* Clear the Cache and
* Remove Cookies '''''Warning ! ! '' This will log you out of sites you're logged in to.'''
Type '''about:preferences'''<Enter> in the address bar.
* '''Cookies;''' Select '''Privacy.''' Under '''History,''' select Firefox will '''Use Custom Settings.''' Press the button on the right side called '''Show Cookies.''' Use the search bar to look for the site. Note; There may be more than one entry. Remove '''All''' of them.
* '''Cache;''' Select '''Advanced > Network.''' Across from '''Cached Web Content,''' Press '''Clear Now.'''
If there is still a problem,
'''[https://support.mozilla.org/en-US/kb/troubleshoot-firefox-issues-using-safe-mode Start Firefox in Safe Mode]''' {web link}
While you are in safe mode;
Type '''about:preferences#advanced'''<Enter> in the address bar.
Under '''Advanced,''' Select '''General.'''
Look for and turn off '''Use Hardware Acceleration'''.
Poke around safe web sites. Are there any problems?
Then restart.

I am getting a error IO when trying to upload multiple images within wordpress using the flash uploader. I do not get the error when uploading using explorer. The error only appears if I try uploading using firefox....any ideas?

I am getting a error IO when trying to upload multiple images within wordpress using the flash uploader. I do not get the error when uploading using explorer. The error only appears if I try uploading using firefox....any ideas?

Logged the call with SAP who directed me to 'Define settings for attachments' in IMG and setting the 'Deactivate Java Applet' & 'Deactivate Attachment versioning' checkboxes - problem solved.

I connected my iphone 3g to itunes which was in 4.1 firmware and itunes ask for an update which i downloaded an updated the phone to version 6.1.3 but my phone cannot start it shows no service my sim card is not getting network and i cannot use the phone.

i connected my iphone 3g to itunes which was in 4.1 firmware and itunes ask for an update which i downloaded an updated the phone to version 6.1.3 but my phone cannot start it shows no service my sim card is not getting network and i cannot use the phone. what should i do.?

First, you do not have a 3G if you could upgrade it to 6.1.3, because 4.2.1 is the last version that will work on the 3G. So you either have a 3GS or you somehow hacked the phone to install an incompatible version. You can check the model you have by entering your serial number here: https://selfsolve.apple.com/agreementWarrantyDynamic.do
Assuming you have a 3GS the most likely reason for your problem is you have a gray market phone that was hacked or jailbroken to unlock it. When you upgraded it you removed the hack, so the phone is now locked to its original carrier.

I am looking for a specific photo in my event folder, it does not show up, yet when I use the search feature, the photo is there. Why doesn't it show up in the folder?

I am looking for a specific photo in my event folder, it does not show up, yet when I use the search feature the picture is there. Why doesn't it show up in the folder?

What system and iPhoto version are you running?
If your're using iPhoto 9 or later Command (right) - click on the photo in the search window and select Show Event in the Contextual menu.
That will take you to the event where the photo is.
OT

My iphone 4 does not ring for messages when i use the handsfree..

my iphone 4 does not ring for messages when i use the handsfree..

iPhone supports A2DP audio streaming. If you have it paired to a handsfree kit that supports this, for example, an in car audio system, and are currently tuned to a source other than the phone, the phone will send the audio for things like text message alerts to the handsfree system, but you will not hear them. This is just the nature of the beast. If you do not intend to use audio streaming from the phone, you may be able to disable this in the in car system. This should not affect Bluetooth calling. There is no option to disable this on the phone itself.

TS1559 wi-fi does not respond ; in settings when i get to screen: chose a network even that wi-fi is on the whole screen freezes and does not respond to touch. i have to press home button to go out. settings point is not coresponding either (in top left c

wi-fi in settings does not respond to touch, page becomes frozen and i have to out from it with home button. can not choose network or anything on that screen!?

noelani72 wrote:
I'd be curious to go buy an old Linksys WRT54G Wifi Router and see how the iPads work on it....but my lord, I have already spent so much time on this issue as it is.
Message was edited by: noelani72
Unless you get that WRT54G for free or next to free, pass on it and pick up an old apple WAP off eBay or similar site. Like you my iPad has a connectivity problem with the WRVS4400N running iOS 4.2.1, where it didn't have trouble with iOS 3.2.2 and ran fine for five months.
My solution at the office was to spur a second router off my DSL router just for the iPad. The first was a WRT54G that had to be set to only one 802.11 protocol to keep the iPad reliably connected, but swapped it out for an old airport extreme that I kept on after testing it to be good. With a home network like you describe, I would run a subnet off the WRVS4400N just for iPad using an apple WAP (the configuration app for Windows is easy to use).
Good luck.

Will you please help me? ipad will not reset "network settings" or forget network!

My ipad will not connect to WiFi although my laptop does. When I try to reset network settings the old settings reappear. It will not "forget this network". What do i need to do next?

I don't fully understand what the System Reset does but I've found that it cures many ills. It's easy, quick and harmless:
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears.
A System Reset does not remove any apps, music, movies, etc. nor does it cause any settings to revert back to default.
Also, you might wish to download the iPad-2 User Guide. Pay special attention to page 162. Note that this Guide also applies to the iPad-1 with IOS 4.3 except for those functions that are not supported by the hardware.
http://support.apple.com/manuals/#ipad
Finally, the User Guide can be downloaded at no charge via iBooks and a less comprehensive version of the Guide is included as a Safari bookmark.

"could not access network location" when upgrading to iTunes 10

Hi, I really know nothing about computers, I'm sorry. I have tried to search for the answers myself but I don't understand much of the language and I'm not sure if I'm reading the appropriate information.
I wanted to update my iTunes on my computer (Windows XP) but it didn't seem to work when I looked for upgrades and clicked yes, I want to update. Nothing happened.
So I unistalled my old iTunes and tried to install the new iTunes 10. But when I did that, I got an error message, with the title of iTunes + QuickTime... saying... could not access network location.
I uninstalled Quicktime to see if that was the problem, and I tried to install iTunes 10 again and the same error message appeared "could not access network location".
From what I googled, it looked like I had to look at something in Run. I got to the specific location but didn't see any obvious errors. But then again, I really had no idea what I was looking at! What do I need to do?
Please I need help (frustrated)!

I uninstalled Quicktime to see if that was the problem, and I tried to install iTunes 10 again and the same error message appeared "could not access network location".
Which location is being cited in the message, fyr? For example, is it %APPDATA% , or something else? (The location given in the message dictates how we go about trying to fix this ... I know of at least three different issues that can cause the 1606 error message on the install, and each requires a different treatment.)

WAE-674 not retaining network settings when configured using recovery CD

Similar Messages

Maybe you are looking for