WAE-674 running 5.1.1.d code

WAE-674 running 5.1.1.d code. The WAE-674 stops working until a reboot or move to another switch port. Are there any known connectivity issues?

Does the switch show any errors on the port before it stops communicating? "Show Logg" on switch to see if it is giving any errors. Are you using WCCP or inline for communication? Is it the management port (WCCP port) or the inline port that is losing communication? I was on 5.1.1c with no issues before I went to 5.3.1, never went to 5.1.1d
If you think it is a version issue, do a quick upgrade to see if it resolves the issue. It is already unreliably bouncing, an upgrade will not hurt any more. Or, even a downgrade to what you were running before 5.1.1.d. Did the issue begin right after you upgraded to 5.1.1.d? Is that why you believe it is the code version causing the issue?

Similar Messages

WAE 674 Disk based software not installed.

Hi,
Have an WAE 674 with 4.4.3c installed, with problem.
Using WCCP and I am able to logon to the device.
Have this msg and in in the CM it is down.
System Initialization Finished.
Disk based software not installed.
Some applications may not run correctly!
Any sugestion?
I have reload still problem.
Regards Jan Rockstedt

What steps did you take to resolve the issue? I have the same issue on WAVE 594 running 4.4.5.
I get the error message when I telnet into device.

WAE-674 WCCP with 3725 router

Hello all,
This is a new install, I am trying to bring up a WAE-674 box at one my remote sites with 2 routers (a 3725 and a 2621) at this remote site and I am using WCCP for traffic redirection. I am having an issue with WCCP on the 3725 router, for some reason when I enable the command "IP wccp 62 redirect in" under the WAN serial interface I suddenly can no longer telnet to the fastethernet interface on the router but I can still ping it and still able to telnet to the loopback interface. And I have no issue with WCCP on the other 2621 router with the same config setup.
Has anyone run into this issue before ? I appreciate any feedbacks on this !!!!
I am running IOS version 12.3(14)T7 on the 3725 router and WAAS software version 4.1.1c
Thanks in advance !!
Danny

You will want to explore CSCsg30875 to see how it applies to your installation
CSCsg30875 wccp blocking telnet to router
Since 12.3T is EOL, it probably was not tested and may or may not exist in that Cisco IOS track.
End-of-Sale and End-of-Life Announcement for Cisco IOS Software Release 12.3T
http://www.cisco.com/en/US/prod/collateral/iosswrel/ps8802/ps6947/ps5207/prod_bulletin0900aecd803a0ffe.html
Thank You,
Dan Laden

WAE 674 multipurpose

HI there,
I have configured Cisco WAE 674 as Content Engine conntected with Websense Server for filtering.Can I use the same device also as WAAS and configure WCCP ?
thanks a lot!

Hi ,
Yes you can use the 674 as either WAAS device or content engine. To do this you need to use the CD recovery procedure in formating the flash,disk and installing the WAAS IOS image.
If you have WAAS recovery CD then run these steps:
2,3,5,7,8, remove the CD from the CD Drive and 9
Regards,
Bala

How to set the File Path to run a javascript using Plugin Code?

Hi All,
Im new to Indesign Plugin Development.Can any one help me out with my problem.
What i want to do is to run a javascript using Plugin Code.When i went through this forum i was able to find out that i should use the IscriptRunner Class to automate this.I could also figure out that the Member Function to use is "CanHandleFile" &"RunFile".
The first parameter in CanHandleFile & RunFile Member Function is to specify the path of the JavaScript File i suppose!I could also find out that IDFile has to used to set the file path Information.
But im clueless how to set the Javascript FilePath using IDFile.Can any one help me how to do this?Any Code Snippets Please?
Waiting for reply.
Thanks
myRiaz

Hi, Andreas Can you explain this in detail? I found it in your post before. The content of elements are returned through the Characters callback function: From ISaxContentHandler.h: /** Receives character data The parser will call this method to report each chunk of character data. SAX parsers may return all contiguous character data in a single chunk, or they may split it into several chunks. But all characters in any single event must come from the same external entity so the Locator provides useful information. Note some parsers will report whitespace using the IgnorableWhitespace() method rather than this one (validating parsers must do so). @param Chars The characters from the XML document. */ virtual void Characters(const PMString& chars) = 0; What i have done is implement my own SAXContentHandlerServiceBoss, and in my file XXXSAXContentHandler.cpp, I override the fonctions StartElement, EndElement, and Characters() like below: I add the PMString xmlData to collect the file content: class XXXSAXContentHandler : public CSAXContentHandler { void XXXSAXContentHandler::Characters(const WideString& chars) { xmlData.Append(chars); } void XXXSAXContentHandler::StartElement(const WideString& uri, const WideString& localname, const WideString& qname, ISAXAttributes* attrs) { xmlData.Append("<"); xmlData.Append(localname); xmlData.Append(">"); } void XXXSAXContentHandler::EndElement(const WideString& uri, const WideString& localname, const WideString& qname) { xmlData.Append("</"); xmlData.Append(localname); xmlData.Append(">"); } } and in my program, I use the code below to call the fonction I overrided, but I dont know how I can get the String xmlData I defined in the XXXSAXContentHandler.cpp InterfacePtr<IK2ServiceRegistry> serviceRegistry(gSession, UseDefaultIID()); InterfacePtr<IK2ServiceProvider> xmlProvider(serviceRegistry->QueryServiceProviderByClassID(kXMLParserService, kXMLParserServiceBoss)); InterfacePtr<ISAXServices> saxServices(xmlProvider, UseDefaultIID()); InterfacePtr<ISAXContentHandler> saxHandler(::CreateObject2<ISAXContentHandler>(kXXXSAXContentHandlerServiceBoss)); saxHandler->Register(saxServices); bool16 parseFailed = saxServices->ParseStream(readStream, saxHandler); Can you give me any help? Thanks and regards!

ABAP/4 run time error with error code SNAP_NO_NEW_ENTRY

Dear All,
I've installed SAP R/3 IDES on Oracle on Windows 2003 server.After clicking Log on button , I should be asked to enter client,user and password.But, my system does not display such details.Instead I get ABAP/4 run time error with error code SNAP_NO_NEW_ENTRY that too after a long time.
Can you please address what is the reason for this problem and how to over ride it?
Regards,
S.Suresh

Hi,
the most probable reason is an archiver stuck. Backup the archived redo log files and delete them afterwards.
The database will archive some more logs after this. Handle them in the same manor. For complete explanation search for brtools.
Regards
Ralph Ganszky

Facing problem with running exe from my java code

Hello,
I have to run the exe from java code for which I m using Runtime and Process classes. The exe runs in the following way on command line
C:/ myexe -j [now press enter]
input sentence followed by ! [now press enter]
And after this exe gives the output.
So is there any way to achieve this programmatically in Java?
Thanks in advance.
Regards,

I m confused .. how can i pass input to the Process through InputStream? I think it will need OutputStream for that.
Here is my code...
import java.io.*;
class CallToExe
static BufferedReader br;
public static void main(String[] args)
File F = new File("C:/Chasen.exe");
try
if( F.exists())
     System.out.println("Exe exists");
     Runtime rt = Runtime.getRuntime();
     Process proc = rt.exec("C:/chasen.exe");
     br = new BufferedReader(new InputStreamReader(in));
     int a = in.read();
     System.out.println(a);
     String res = br.readLine();
     System.out.println(res);
     while(!res.equals(null))
     System.out.println(res);
     res = br.readLine();
proc.waitFor();
     proc.destroy();
catch(NullPointerException npe)
     npe.printStackTrace();
catch (Exception IOEx)
IOEx.printStackTrace();
But it doesnt work as my chasen.exe needs arguments from stdin.
The way exe works is as follows.
on command prompt>>
C:/chasen.exe -j [ Need to press ENTER here]
input statement . [ Need to press ENTER here too]
Then output is displayed on command prompt which can be taken from InputStream of the process. But I m not able to properly run this exe itself with all the arguments frm Stdin

RUN TIME ERROR IN THIS CODE

HELLO EVERY ONE ...
I AM GETTING run time error in this code.....can u send me the corrected code....
START-OF-SELECTION.
SELECT T1~MATNR
       T1~MEINS
       T1~ERSDA
       T1~ERNAM
       T1~SPART
       T2~MAKTX
       T3~LVORM
       T3~EKGRP
       T3~WERKS
       T4~LABST
       T4~SPEME
       T4~LGORT
       INTO CORRESPONDING FIELDS OF TABLE ITAB
       FROM MARA AS T1
       INNER JOIN MAKT AS T2
       ON T1MATNR = T2MATNR
       INNER JOIN MARC AS T3
       ON T2MATNR = T3NFMAT
       INNER JOIN MARD AS T4
       ON T3MATNR = T4MATNR
       WHERE T1~MATNR IN SMATNR.
Thanx & Regards,
PHANINDER

ok i am sending u the full code.....
REPORT Z_SB_RP_MATERIAL.
TABLES: MARA,
        MARD,
        MAKT,
        MARC,
        EINA,
        EINE.
DATA: BEGIN OF ITAB OCCURS 15,
      MATNR LIKE MARA-MATNR,
      MEINS LIKE MARA-MEINS,
      ERSDA LIKE MARA-ERSDA,
      ERNAM LIKE MARA-ERNAM,
      SPART LIKE MARA-SPART,
      MAKTX LIKE MAKT-MAKTX,
      LVORM LIKE MARC-LVORM,
      EKGRP LIKE MARC-EKGRP,
      WERKS LIKE MARC-WERKS,
      LABST LIKE MARD-LABST,
      SPEME LIKE MARD-SPEME,
      LGORT LIKE MARD-SPEME,
      END OF ITAB.
SELECTION-SCREEN BEGIN OF BLOCK BLK WITH FRAME TITLE TEXT-T01.
SELECT-OPTIONS: SMATNR FOR MARA-MATNR,
                SERSDA FOR MARA-ERSDA,
                SWERKS FOR MARC-WERKS,
                SLGORT FOR MARD-LGORT.
SELECTION-SCREEN END OF BLOCK BLK.
TOP-OF-PAGE.
WRITE:/ SY-VLINE,
      02 'S.NO',
      06 SY-VLINE,
      08 'MATNR',
      20 SY-VLINE,
      22 'MEINS',
      32 SY-VLINE,
      34 'ERSDA',
      44 SY-VLINE,
      46 'ERNAM',
      56 SY-VLINE,
      58 'SPART',
      68 SY-VLINE,
      70 'MAKTX',
      80 SY-VLINE,
      82 'LVORM',
      92 SY-VLINE,
      94 'EKGRP',
     104 SY-VLINE,
     106 'WERKS',
     116 SY-VLINE,
     118 'LABST',
     128 SY-VLINE,
     130 'SPEME',
     140 SY-VLINE,
     142 'LGORT',
     152 SY-VLINE.
START-OF-SELECTION.
SELECT T1~MATNR
       T1~MEINS
       T1~ERSDA
       T1~ERNAM
       T1~SPART
       T2~MAKTX
       T3~LVORM
       T3~EKGRP
       T3~WERKS
       T4~LABST
       T4~SPEME
       T4~LGORT
       INTO CORRESPONDING FIELDS OF TABLE ITAB
       FROM MARA AS T1
       INNER JOIN MAKT AS T2
       ON T1MATNR = T2MATNR
       INNER JOIN MARC AS T3
       ON T2MATNR = T3NFMAT
       INNER JOIN MARD AS T4
       ON T3MATNR = T4MATNR
       WHERE T1~MATNR IN SMATNR.
END-OF-SELECTION.
DATA: COUNT(4) TYPE N.
LOOP AT ITAB.
COUNT = COUNT + 1.
WRITE:/ SY-VLINE,
      02 COUNT,
      06 SY-VLINE,
      08 ITAB-MATNR,
      20 SY-VLINE,
      22 ITAB-MEINS,
      32 SY-VLINE,
      34 ITAB-ERSDA,
      44 SY-VLINE,
      46 ITAB-ERNAM,
      56 SY-VLINE,
      58 ITAB-SPART,
      68 SY-VLINE,
      70 ITAB-MAKTX,
      80 SY-VLINE,
      82 ITAB-LVORM,
      92 SY-VLINE,
      94 ITAB-EKGRP,
     104 SY-VLINE,
     106 ITAB-WERKS,
     116 SY-VLINE,
     118 ITAB-LABST,
     128 SY-VLINE,
     130 ITAB-SPEME,
     140 SY-VLINE,
     142 ITAB-LGORT,
     152 SY-VLINE.
ENDLOOP.
THANX & REGARDS,
PHANINDER

Please do the following: -Close any running programs -Empty your temporary folder -Check your internet connection (Internet-based Setups) Then try to run setup again. Error code -6003. How do I empty temporary folder?. Thanks. Allan

I am having a problem installing Nikon Codec, software to view photos and get this error error message: Setup has experienced an error. Please do the following: -Close any running programs -Empty your temporary folder -Check your internet connection (Internet-based Setups) Then try to run setup again. Error code -6003. How do I empty temporary folder?. Thanks. Allan

Clear the cache and the cookies from sites that cause problems.
"Clear the Cache":
* Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
"Remove Cookies" from sites causing problems:
* Tools > Options > Privacy > Cookies: "Show Cookies"
*http://support.mozilla.com/kb/Deleting+cookies
*http://support.mozilla.com/kb/How+to+clear+the+cache

Can I run the Servlet and Bean code on Sun ONE Webserver 6.1 SP5

Hi all.
My environment as below.
1) Windows 2000 Server SP4
2) Sun ONE Webserver 6.1 SP5
3) JRE1.5.0
The directory ( WEB-INF/classes) where is to create on. I have a Bean and Servlet code but I can't
to run it on. Another code Jsp, HTML can run.
How can I do?

Your question is somewhat vague, but I'll presume that you are asking how you can invoke your servlets.
If the servlet classes are correctly deployed, you can invoke them directly. i.e. http://host/<app>/servlet/<classname>. Or, you can create servlet mappings.
Java beans cannot be invoked the same way a servlet can. You can access beans from within servlets.
For more details, check out the servlet tutorials at http://java.sun.com

WAE 674 booting issues

I am having issues with my WAE 674.
Powered on for the first time and was hanging at the booting the kernel screen.
Then used the software recovery CD waas-rescue-cdrom-4.4.1.12-npe-k9.iso, it went through all the steps of installation.
After reboot it hangs at booting the kernel, it does not move from this point. Nothing on the hyperterminal.
I have attached the screenshot.
Any ideas?
Thanks,
Suhail.

Hi Suhail,
How are you connected to the WAE?
If you are directly connected to the WAE through a screen/keyboard, I believe that what you see is expected: the WAAS software stop redirecting it's console output on the screen after booting it's kernel and move it to the serial port.
This is explained in the hardware specs of your device:
You can connect a keyboard to any USB port and connect a monitor to the video connector to troubleshoot the BIOS boot process. However, video output is for troubleshooting only during the BIOS boot process. The video output stops displaying when the serial port becomes active. To monitor the boot process in normal operation, use the serial console port.
http://www.cisco.com/en/US/partner/docs/app_ntwk_services/waas/wae/installation/7341-7371/guide/7300intr.html#wp1040565
Could you have a look at the boot sequence from the serial port and see if everything looks fine from there?
Regards,
Nicolas

Cisco WAAS WAE-674 - Slow response in IE-7 PC's while trying to access the SAP application through cisco WEA

Hi,
From location A when we are trying to access the SAP application in location B through WAE-674 via internet Explorer there is a slow response in IE-7 PC's compare to IE-8 PC's,But when we try without WAE-674 the response is normal.
We also found that optimization in location A WAAS device as 70-90% but still users are facing slowness while opening the Webpage.
Please suggest how to address the problem ASAP.
Thanks & Regards,
P.Ramkumar

I would suggest that you open a case with the tac to look at this. Matthew

Is the HWIC-4ESW card supported in the WAE-674-K9?

Hi,
In the datasheet of the WAE-674-K9 says that it supports (4-port network interface card (NIC) for inline Cisco WAAS deployment), but don't mention the HWIC-4ESW anywhere. Is it supported?
Any help is much appreciated!

Hi,
The WAE-674-K9 support 4 port NIC for Inline Deployment and the card is WAE-INLN-4CG.
HWIC-4ESW is not supported.
http://www.cisco.com/en/US/prod/collateral/contnetw/ps5680/ps6474/data_sheet_c78-495801.html
Regards
Kiran.

WAE 674 Max TCP Connections

Does anyone know how many TCP connections the 674 will support with various memory options?
TIA
mike

Mike,
The WAE-674 will support the following memory/connection options:
4GB = 2,000 Connections
8GB = 6,000 Connections
Regards,
Zach

WAE-674 as a Content Engine

Dear All Experties,
We are using a Cisco Content engine 7325 as a proxy server.recently we brough WAE-674 as a replacement of these old content engine.After turn on WAE-674,Blue screen pop up on moniter.I am not able to access anything with GUI as well through command line.That why i am not able to configure that one.
Please advise me if anybody else also faced this problem or if anybody have any idea what i can do ???
Thanks in advance

Hi,
How are you connected to the WAE?
If you are directly connected to the WAE through a screen/keyboard, what you see might be expected: the WAAS/ACNS software stop redirecting it's console output on the screen after booting it's kernel and move it to the serial port.
This is explained in the hardware specs of your device:
You can connect a keyboard to any USB port and connect a monitor to the video connector to troubleshoot the BIOS boot process. However, video output is for troubleshooting only during the BIOS boot process. The video output stops displaying when the serial port becomes active. To monitor the boot process in normal operation, use the serial console port.
http://www.cisco.com/en/US/partner/docs/app_ntwk_services/waas/wae/installation/7341-7371/guide/7300intr.html#wp1040565
Could you have a look at the boot sequence from the serial port and see if everything looks fine from there?
Regards,
Nicolas

WAE-674 running 5.1.1.d code

Similar Messages

Maybe you are looking for