WAE - Inline Module - Interception ACL - Statistics

Hello, I have a wae connected inline to the ISP Router.
The Router provide connectivity to Internet from a serial interface and from another serial interface to the DataCenter.
When I look the statistic of the Optimization/Acceleration, the value are related to all traffic; between branch office and datacenter, and to Internet.
I want the statistics only of the traffic between branch office and data center
if I use an Interception ACL on the wae with permit the traffic between private network, I can see the statistic related only this quantity of traffic between private networks ?
or, Do you have suggestions to have statistics without internet traffic ?

hi Marco,
You can create an ACL to limit the traffic intercepted.Make sure that the interception ACL is created to match traffic flow bidirectionally on the device. Interception ACLs need to match only the TCP SYN packet to exclude a session from optimization. Considering both directions of traffic flow will help limit unanticipated optimization traffic.
Source:
http://www.cisco.com/en/US/prod/collateral/contnetw/ps5680/ps6870/white_paper_c11-609128.html
I still don't fully understand how your network design really is but I hope this helps.

Similar Messages

WAAS WAE Inline Vlans

Switch with trunk to router, whith the wae inline between them I cannot get between vlans, from the wan side I can get to all resource, Any ideas what to configure or look at

Are you trying to only intercept one VLAN or all the VLANs? You can configure this on the inline card's interface or in the CM GUI under the Interception section for that device.
Dan

Cisco Clean Access - Intercept ACL standard config

If implementing an out-of-band CCA solution, with a router acting as the Network Access Device (NAD), would the Intercept ACL standard config be to allow access to the network, or just to the submet where the AAA Policy Server, etc are?
If there are URLs to examples, that would help too.
Thanks!

First, you will need to open up traffic in the unauthenticated role for tcp port 636 to the LDAP server.
The deal with the certs is that you need the CAM to be able to trust the LDAP servers cert, so you need the root cert corresponding to the LDAP servers cert. You can then upload that on the CAM under "CCA Manager" > "SSL Certificate", drop the box down to "Import Certificate" and then drop the next box down to "Trust non-standard CA". Upload and install
the root to there.

WAE Inline Deployment on a router intergated switch module

Hi,
Is it possible to simulate an inline WAE deployment on a router with an integrated switch module?
Thanks.
Ed.

Ed,
Unfortunitely you have to use WCCP or PBR with NME-WAE. Inline is only possible with the inline card on an appliance.
Dan

WAE Inline Adapter and High Availability

What is the recommendation to achieve high availability (and load sharing?) using two WAE's in a DC with inline adapters being used for interception rather than WCCPv2? Any ideas greatly appreciated.

Ken,
Generally I would recommend interception with either WCCP or a L4-7 load balancer like ACE/ACE Appliance/CSM. Both of these are considered best practice for DC deployments as they both can handle high amounts of traffic, can handle WAEs going offline and can load balance many WAEs in a cluster. WCCP might be slightly more flexible where and how you can deploy it.
Both of the following interception techniques are not recommended for data centers, but I list just as FYI:
- Inline cards in appliances can be configured in serial to give you high availability, but you don't get load balancing. The second appliance only starts optimizing traffic once the first WAE starts passing traffic through on overload. Inline interception is usually used for remote offices, however it has been deployed in DCs.
- PBR can be configured for high availability with next-hop features, however there is no available load balancing. The first WAE has to fail completely and then a second WAE can come into play. Overloaded traffic is not optimized at all.
Hope that helps,
Dan

WAE inline or WCCP on data center

Hi all,
Is WAE(674)inline mode fine for data center or should I go for WCCP?
Any idea about throuput of inline adaptor?
Thanks

Hi Nomair,
I usually start with WCCP in the DC due to the fact that you are limited to intercepting on 2 links with the inline card currently and most DC scenarios have requirements of using more then 2 links (or routers).
Thanks,
Dan

WAE Network Module

We are looking to deploy WAAS enterprise wide in a MPLS network I currently support. Our client routers function as both CE and PE - the egress interface is label switched and the customer host facing interface resides within a MPLS VRF. We would like to deploy the NM-WAE modules at each site. Are these modules VRF aware? I need to perform the WCCP redirection/inspection on the interface assigned to the VRF. I couldn't find any documents specific to WAAS and MPLS. Has anyone dealt with this yet? Thanks in advance.

HI,
The VRF awareness for 12.4(T) is still probably 8-12 months out. VRF aware WCCP features are definitely in the pipeline, but nothing has been publically published on availability timelines.
It's now publically available on the forum... but , I've only found it on the 3750 and 3550 documentation.
at the 3750 you will need to place the redirect statement on each of the VLANs, ip wccp 61 redirect in
Kindly find here GRE Tunnel with VRF Configuration Example:
http://www.cisco.com/en/US/tech/tk436/tk428/technologies_configuration_example09186a00801e1294.shtml
I have gotten as far as the WAE registering the router:
"WCCP configuration for TCP Promiscuous service 61 and 62 succeeded.
WCCP configuration for TCP Promiscuous succeeded.Please remember to
configure WCCP service 61 and 62 on the corresponding router."
wae01#sh wccp router
Router Information for Service: TCP Promiscuous 61
Routers Configured and Seeing this Wide Area Engine(1)
Router Id Sent To Recv ID
0.0.0.0 209.1.1.1 0000022F
The router registers the WAE as a WCCP client:
router04#
"*Feb 4 18:56:09.892: %WCCP-5-SERVICEFOUND: Service 61 acquired on WCCP
client 209.1.1.2"
"*Feb 4 18:56:09.892: %WCCP-5-SERVICEFOUND: Service 62 acquired on WCCP
client 209.1.1.2"
The router however cannot figure out what its ID is and does not see
itself as a WCCP group router.
router04#sh ip wccp
Global WCCP information:
Router information:
Router Identifier: -not yet determined-
Protocol Version: 2.0
Service Identifier: 61
Number of Service Group Clients: 1
Number of Service Group Routers: 0
Total Packets s/w Redirected: 0
Process: 0
Fast: 0
CEF: 0
Redirect access-list: ACCELERATED-TRAFFIC
Total Packets Denied Redirect: 0
Total Packets Unassigned: 25957
Group access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
This is a short summary of important commands for working with VRF's.
View the VRF instances and the associated interfaces.
ml-mr-c6-gs#show ip vrf
Name Default RD Interfaces
blurvrf 100:2 Vlan215
Vlan326
tgvrf 100:1 Vlan132
Vlan325
TenGigabitEthernet1/1
ml-mr-c6-gs#
Show the routing table for a specific VRF.
ml-mr-c6-gs#show ip route vrf tgvrf
Routing Table: tgvrf
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external,
---More--
Gateway of last resort is 128.117.243.57 to network 0.0.0.0
O E2 192.52.106.0/24 [110/1] via 128.117.243.57, 1d19h, Vlan325
O E2 192.168.150.0/24 [110/160] via 128.117.243.57, 1d19h, Vlan325
172.17.0.0/29 is subnetted, 3 subnets
O E2 172.17.1.16 [110/0] via 128.117.243.57, 1d19h, Vlan325
O E2 172.17.1.8 [110/1] via 128.117.243.57, 1d19h, Vlan325
O E2 172.17.1.0 [110/1] via 128.117.243.57, 1d19h, Vlan325
--More--
Debugging should otherwise be similar to a regular switch or router.
Final Teragrid VRF Design and Diagrams
http://www.cisl.ucar.edu/nets/devices/routers/cisco/vrf/final.shtml
Teragrid Testbed Design
http://www.cisl.ucar.edu/nets/devices/routers/cisco/vrf/testbed.shtml
Cisco 4500 Series Switch Cisco IOS s/w config guide 12.1(20)EW
Configuring VRF-Lite
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.1/20ew/configuration/guide/vrf.html
sachin garg

FNDGSCST module: Gather Schema Statistics - ERROR: While GATHER_TABLE_STATS

Hi
I ran gather schema Statistics
In GATHER_SCHEMA_STATS , schema_name= ALL percent= 10 degree = 4 internal_flag= NOBACKUP
the error are:
stats on table AQ$_WF_CONTROL_P is locked
stats on table FND_CP_GSM_IPC_AQTBL is locked
Error #1: ERROR: While GATHER_TABLE_STATS:
object_name=AP.JE_FR_DAS_010***ORA-20001: invalid column name or duplicate columns/column groups/expressions in method_opt***
Error #2: ERROR: While GATHER_TABLE_STATS:
object_name=AP.JE_FR_DAS_010_NEW***ORA-20001: invalid column name or duplicate columns/column groups/expressions in method_opt***
Error #3: ERROR: While GATHER_TABLE_STATS:
object_name=AP.JG_ZZ_SYS_FORMATS_ALL_B***ORA-20001: invalid column name or duplicate columns/column groups/expressions in method_opt***
I ran this while ago.
anyone can help me to fix it
Thanks

Please see old threads which discuss the same issue -- http://forums.oracle.com/forums/search.jspa?threadID=&q=Gather+AND+Schema+AND+Statistics+AND+ORA-20001&objID=c3&dateRange=all&userID=&numResults=15&rankBy=10001
Thanks,
Hussein

WAAS inline without module?

Is it possible to use a WAE appliance (WAE-512-K9) as an inline device without purchasing a WAE-INLN-4CG=? The device has 2 NICS, and I really wouldn't have a need for more than 1 port in and 1 port out.
Thanks,
Jason

Jason,
The inline module is required to deploy the WAE using inline interception.
Thanks,
Zach

Waas (4.2.1) in inline mode not optimizing

Hello
noob-question here regarding waas, sorry for that.
But I've been reading all day and I can't understand why this isn't working.
It seems traffic is not optimized, the graphs in the central manager are basically empty.
I'm currently working on a deployment with 3xappliances
Where 1 is the manager and 2 WAE
Location of these WAE is pretty much in different continents.
I will call them New York and Sydney from here.
The hardware of the WAE's is
New York      WAVE-274-K9
Sydney         WAVE-574-K9
And these are setup in inline mode.
So basically we have a switch and an ASA on both sites, in between is the WAE listening to all VLANs.
The ASA's are configured for inspect waas.
Versions on all of them is 4.2.1.
In NY all I'm seeing when I issue 'sh stat conn' is
PT in progress
PT No peer
This is making me think that somehow the WAE's are not finding each other.
In the central manager under both WAE's
Automatically Configure Peer is checked.
However I'm not sure how to verify that they are actually discovering each other.
Below are some show commands, not sure if they are to any help.
Looking at the inlinegroup in New York
sh int inlinegroup 1/1
Interface is in intercept operating mode.
WAN Port :
===========
Device name        : eth1. Bypass master interface.
Packets Received   : 368334207
Packets Intercepted: 187076874
Packets Bridged    : 181892022
Packets Forwarded : 190416781
Packets Dropped    : 3
Packets Received on native      : 0
Active flows for this interface : 0
and the inlinegroup in Sydney
sh int inlinegroup 1/0
Interface is in intercept operating mode
WAN Port :
===========
Device name        : eth2. Bypass master interface.
Packets Received   : 2157944591
Packets Intercepted: 2090403196
Packets Bridged    : 73392781
Packets Forwarded : 1789726515
Packets Dropped    : 49
Packets Received on native      : 0
Active flows for this interface : 0
sh stat pass-trough in New York
sh statistics pass-through
                      Outbound
PT Client:
     Bytes                      120192829511
     Packets                       136188837
PT Server:
     Bytes                       45736943268
     Packets                       126276288
PT In Progress:
     Bytes                       43839787065
     Packets                        93203689
                      Active                    Completed
Overall                                    4                   9456941
No Peer                                    0                   6168740
Rjct Capabilities                          0                         0
Rjct Resources                             0                      1083
Rjct No License                            0                         0
App Config                                 0                    105544
Global Config                              0                         0
Asymmetric                                 0                      2280
In Progress                                4                   3148696
Intermediate                               0                         0
Internal Error                             0                         0
App Override                               0                         0
Server Black List                          0                     30598
AD Version Mismatch                        0                         0
AD AO Incompatible                         0                         0
AD AOIM Progress                           0                         0
DM Version Mismatch                        0                         0
Peer Override                              0                         0
Bad AD Options                             0                         0
Non-optimizing Peer                        0                         0
Interception ACL                           0                         0
And the same in Sydney
sh stat pass-through
                      Outbound
PT Client:
     Bytes                      797658174849
     Packets                      1233930472
PT Server:
     Bytes                      574115264312
     Packets                      1097913979
PT In Progress:
     Bytes                      570246018011
     Packets                      1445320890
                      Active                    Completed
Overall                                    0                  66152228
No Peer                                    0                  26131796
Rjct Capabilities                          0                         0
Rjct Resources                             0                        77
Rjct No License                            0                         0
App Config                                 0                    458147
Global Config                              0                         0
Asymmetric                                 0                     31142
In Progress                                0                  39525953
Intermediate                               0                         0
Internal Error                             0                         2
App Override                               0                         0
Server Black List                          0                      5111
AD Version Mismatch                        0                         0
AD AO Incompatible                         0                         0
AD AOIM Progress                           0                         0
DM Version Mismatch                        0                         0
Peer Override                              0                         0
Bad AD Options                             0                         0
Non-optimizing Peer                        0                         0
Interception ACL                           0                         0
I'm thinking about upgrading them all to the latest release 5.1.1.
Do I have to jump to (for example) 4.3.1 and then to 5.1.1 ?

Doesn't look like it was tested. Checking why ...
Zach

Help for wae 7341 device

Hi,
For the first time I am deploting WAE deviece in DC center. Since this is a new technology for me. Can some bosy help me in doing physical connectivity. I am getting confused in WAN in /out interface. Apart from this I want to know how to do basisc level configuration .Can you please help me out in this regards?I
my setup is like one core rtr,one core switch and onr layer2 switch in betwwen core rtr & core switch.
Regards,
APN

Your account team could be the first place you turn, as they can get someone onsite if needed to provide in-person assistance. We also have an internal helpdesk to help Partners with new deployments and trial deployments. And there is Cisco TAC should you encounter problems during the deployment. All of these resources are staffed with people trained and experienced in WAAS.
WAAS provides multiple methods of deployment and interception, including (but not limited to) WCCP and Inline. Inline places the WAE in the path of the packets. WCCP places the WAE out of path of the packets and requires that the router/switch be configured to intercept packets and redirect them to the WAE.
If the WAE comes equipped with inline card, an inline group consists of a pair of interfaces marked LAN and WAN. Connect LAN to the cable connecting to the LAN-side switch/router, and connect WAN to the cable connecting to the WAN-side switch/router. The types of cabling you use, duplex and speed settings on the switches and routers, and placement of the WAE within the network are important.
However, Inline may not be the preferred method for deploying in your datacenter.
If the WAE does not come equipped with an inline card, then the Gigabit interfaces are used to connect to a router/switch, and packets must be redirected to that WAE on that interface. A single interface may be used, or the interfaces may be grouped into a port-channel or standby interface configuration. Redirection from the router/switch is generally accomplished by configuring WCCP on the router/switch and on the WAE. Packets are intercepted at the router on one or more interfaces, and redirected to the WAE. The WAE processes them, performing appropriate optimizations, and egresses them back to the router/switch which forwards them to the destination.
Decide on the interception method. Read the appropriate sections in the documentation and decide how best to connect the WAE and configure interception, based on your datacenter's unique requirements. Probably the fastest way to get started would be to read the quick-start guide, and use the CLI-based setup tool.
Instructions for the inline interface can be found here:
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/wae/module/inline/installation/guide/17880fru.html
Instructions for the WAE-7341 hardware can be found here:
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/wae/installation/7341-7371/guide/7341gd.html
Quick Start guide here:
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v421/quick/guide/waasqcg.html
Configuration (including WCCP) guide here:
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v421/configuration/guide/cnfg.html

Inline network card issue

hi all
Please help with the issue below
I have connected the branch WAE inline to a Nortel Router(Cross cable) and Nortel 8600 Switch(Straight cable) inlineGroup 1/0. I get the following below with the Lan interface on the group administratively shut. I have tried different combinations of cables as well.
interface InlineGroup 1/0
inline vlan all
exit
from sho int inlinegroup 1/0
Interface is in bypass operating mode.
Standard NIC mode is on.
Disable bypass mode is on.
VLAN IDs configured for inline interception: All
Watchdog timer is disabled.
Inline Port Statistics Of The Group:
WAN Port :
===========
Device name        : eth4. Bypass master interface.
Packets Received   : 0
Packets Intercepted: 0
Packets Bridged    : 0
Packets Forwarded : 0
Packets Dropped    : 0
Packets Received on native      : 0
Active flows for this interface : 0
Ethernet Driver Status
Type:Ethernet
Ethernet address:00:E0:ED:0C:6A:0A
Maximum Transfer Unit Size:1500
Metric:1
Packets Received: 0
Input Errors: 0
Input Packets Dropped: 0
Input Packets Overruns: 0
Input Packets Frames: 0
Packet Sent: 0
Output Errors: 0
Output Packets Dropped: 0
Output Packets Overruns: 0
Output Packets Carrier: 0
Output Queue Length:1000
Collisions: 0
Base address:0x6080
Flags:UP BROADCAST MULTICAST
Link State: Interface is up,line protocol down

hi Jan
Please see below. I am running version 4.3.3. no lights are flashing on the card.
Thanks in advance
LAN
Device name        : eth5. Bypass slave interface.
Packets Received   : 0
Packets Intercepted: 0
Packets Bridged    : 0
Packets Forwarded : 0
Packets Dropped    : 0
Packets Received on native      : 0
Active flows for this interface : 0
Ethernet Driver Status
Type:Ethernet
Ethernet address:00:E0:ED:0C:6A:0B
Maximum Transfer Unit Size:1500
Metric:1
Packets Received: 0
Input Errors: 0
Input Packets Dropped: 0
Input Packets Overruns: 0
Input Packets Frames: 0
Packet Sent: 0
Output Errors: 0
Output Packets Dropped: 0
Output Packets Overruns: 0
Output Packets Carrier: 0
Output Queue Length:1000
Collisions: 0
Base address:0x60c0
Flags:BROADCAST MULTICAST
Link State: Interface is administratively down, line protocol down
Mode: autoselect
WAN
Device name        : eth4. Bypass master interface.
Packets Received   : 0
Packets Intercepted: 0
Packets Bridged    : 0
Packets Forwarded : 0
Packets Dropped    : 0
Packets Received on native      : 0
Active flows for this interface : 0
Ethernet Driver Status
Type:Ethernet
Ethernet address:00:E0:ED:0C:6A:0A
Maximum Transfer Unit Size:1500
Metric:1
Packets Received: 0
Input Errors: 0
Input Packets Dropped: 0
Input Packets Overruns: 0
Input Packets Frames: 0
Packet Sent: 0
Output Errors: 0
Output Packets Dropped: 0
Output Packets Overruns: 0
Output Packets Carrier: 0
Output Queue Length:1000
Collisions: 0
Base address:0x6080
Flags:UP BROADCAST MULTICAST
Link State: Interface is up,line protocol down
Mode: autoselect

Duplex problem with inline card "WAN0" again

Hi,
We got duplex problem again "new site" for the inline port WAN0, LAN0 is ok.
We have tried crossover and straight through cable, without any look still 100/ half duplex.
The PTT router int fa0/0 have been to 100/full and auto/auto still 100 half in the WAE.
The WAE have been in 100/full, no link or auto/auto link but 100/half.
What can be the problem, as we have this issue with most of our 574 and 274, the 674 have have no problem at all?
Below are some output from the WAE and router.
PTT router:
#sh ver
Cisco IOS Software, 1841 Software (C1841-SPSERVICESK9-M), Version 12.4(6)T7, RELEASE SOFTWARE (fc5)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 29-Mar-07 03:29 by khuie
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Router uptime is 5 weeks, 1 day, 5 minutes
System returned to ROM by power-on
System restarted at 08:09:29 GMT Sun Aug 15 2010
System image file is "flash:c1841-spservicesk9-mz.124-6.T7.bin"
Cisco 1841 (revision 7.0) with 116736K/14336K bytes of memory.
Processor board ID FCZ112411HV
2 FastEthernet interfaces
1 Serial interface
1 Serial(sync/async) interface
1 Channelized E1/PRI port
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
63488K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
#sh int fa0/0
FastEthernet0/0 is up, line protocol is up
Hardware is Gt96k FE, address is 001b.d5ab.3fc8 (bia 001b.d5ab.3fc8)
Internet address is 10.252.105.12/22
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 103000 bits/sec, 89 packets/sec
5 minute output rate 625000 bits/sec, 93 packets/sec
     110094543 packets input, 2604076581 bytes
     Received 10013739 broadcasts, 0 runts, 0 giants, 0 throttles
     21 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog
     0 input packets with dribble condition detected
     110416771 packets output, 4153304953 bytes, 0 underruns
     149371 output errors, 113762 collisions, 149376 interface resets
     0 babbles, 149940 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
From the WAE:
#sh interface inlineport InlineGroup 1/0/wan
                                     ^
% Invalid input detected at '^' marker.
ZAJOPWAAS01#sh interface inlineport 1/0/wan
Device name        : eth4. Bypass master interface.
Packets Received   : 59466951
Packets Intercepted: 50007028
Packets Bridged    : 10002103
Packets Forwarded : 44722188
Packets Dropped    : 69
Packets Received on native      : 0
Active flows for this interface : 0
Ethernet Driver Status
Type:Ethernet
Ethernet address:00:E0:ED:11:E5:A8
Maximum Transfer Unit Size:1500
Metric:1
Packets Received: 59466909
Input Errors: 0
Input Packets Dropped: 0
Input Packets Overruns: 0
Input Packets Frames: 0
Packet Sent: 64238956
Output Errors: 116996
Output Packets Dropped: 0
Output Packets Overruns: 0
Output Packets Carrier: 116996
Output Queue Length:100
Collisions: 182840
Base address:0x5000
Flags:UP BROADCAST RUNNING MULTICAST
Link State: Interface is up,line protocol up
Mode: autoselect, half-duplex, 100baseTX
1#sh ver
Cisco Wide Area Application Services Software (WAAS)
Copyright (c) 1999-2010 by Cisco Systems, Inc.
Cisco Wide Area Application Services (WAAS-UNIVERSAL-K9) Software Release 4.2.1
(build b38 Jun 16 2010)
Version: oe574-4.2.1.38
Compiled 20:44:26 Jun 16 2010 by damaster
Device Id: 00:26:55:ad:cd:04
System was restarted on Mon Aug 30 16:48:52 2010.
The system has been up for 2 weeks, 6 days, 17 hours, 52 minutes, 10 seconds.
Jan Rockstedt

Hi Jan,
If you are connecting Router to WAN0_0 port, you should use cross-over cable under most of the circumstances and unless you are using all gig interfaces on both sides. This will avoid any hardware limitations due to non-Auto-MDIX supported hardware.
Cisco strongly recommend that you do not use half-duplex connections on the WAE or on routers, switches, or other devices.
You will find more information here: Cabling
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/wae/module/inline/installation/guide/17880fru.html#wp39911
Further, there is a possibility that the interface on Router / WAE inline adapater / cable might be bad. I would suggest following in that case.
1. Using a new cross-over / stright cable. if the issue continues, proble lies on the interface sides.
2. Using a different port on router. if the issue continues, problem is with WAN0_0 port of WAE.
3. Try connecting wan0_0 port to another switch / router to see if it negotiates at full duplex. If it still continues at half duplex, there is an issue with WAN0_0 port most probably.
4. Try connecting secondary gig port or WAN0_1 port to same router interface. If the issue continues, problem may be with router FA0/0 interface.
If you find that issue is with either router / WAE inline interface, please open a TAC case for RMA.
Hope this helps.
Regards.
PS: If this resolves your issue, please mark this as Answered.

WAAS - Can I mix & match inline and off path installations?

Hi - I'm designing a WAAS solution which requires that I deploy the Data centre WAE inline (the core switch is a 3750 which doesn't support WCCP). I plan on using NME modules on the branch sites. Is this mix and matching of deployments permitted or will I run into problems.
Many Thanks :)
Dom

Dom,
Absolutely, you can mix and match. As a matter of fact, a lot of implementations are the opposite with inline at the edge and WCCP at the core. You should have no trouble with this at all.
BTW, the 3750 DOES support WCCP v2 at line rate (i.e. in hardware) with newer versions of IOS if you want to try it. It requires L2 adjacency to the WAEs and the WAEs need to be configured w/L2 redirect/L2 return and mask assign. The 3750 needs to have redirect in on the interfaces and a routing SDM template configured.
Hope that helps,
Dan

WAE Edge is showing offline

Hi All
I have a design where all my WAE are inline in the path of traffic .
One of my WAE Edge shows on the CM as offline and after half an hour it comes online , again it went offline after 1 hour and so on.
What might be the issue and when its offline I can not even remotely telnet to the management intrerface of WAE but its keep on by passing the traffic.
Any body face the same issue , the problem with hardware or any suggestion.
Regards

Hi
Very interesting finding
1- Branch WAE Edge status on CM GUI is offline.
2- Unable to telnet Branch WAE Edge remotely.
BUT
1- Able to telnet Branch WAE Edge from the local netwrok.
2- When I telnet and check the cms info of Branch WAE Edge its showing 'inline'.
3- Branch WAE Edge is intercepting the traffic and optimizing and accelerating the traffic.
Any body can shed light on this issue why I am getting status off line on WAAS CM for this Branch WAE Edge.
Regards

WAE - Inline Module - Interception ACL - Statistics

Similar Messages

Maybe you are looking for