Wanboot issues

Trying to configure wanboot, have gone over the config several times and tired various changes to no avail. Here is the error I receive, and some config is below. Any assistance is greatly appreciated.
{40} ok boot net - install
Boot device: /pci@5c,600000/pci@1/network@1 File and args: - install
/pci@5c,600000/pci@1/network@1: 1000 Mbps full duplex link up
HTTP: Bad Response: 500 Internal Server Error (boot_file missing)
Boot load failed
root@wwpxpssc01-sc0 # cat /etc/netboot/wanboot.conf
boot_file=/wanboot/wanboot
root_server=http://10.230.108.15/cgi-bin/wanboot-cgi
root_file=/wanboot/wpath/miniroot
signature_type=
encryption_type=
server_authentication=no
client_authentication=no
resolve_hosts=
boot_logger=http://10.230.108.15/cgi-bin/bootlog-cgi
system_conf=system.conf
root@wwpxpssc01-sc0 # cat /etc/netboot/system.conf
SsysidCF=http://10.230.108.15/config
SjumpsCF=http://10.230.108.15/config
root@wwpxpssc01-sc0 # cat /var/apache2/htdocs/config/profile
install_type flash_install
archive_location http://10.230.108.15/flashdir/wwpxpsdb01.flar
partitioning explicit
filesys c0t0d0s0 20000 /
filesys c0t0d0s1 8192 swap
filesys c0t0d0s5 20000 /var
filesys c0t0d0s6 free /export/home
root@wwpxpssc01-sc0 # cat /var/apache2/htdocs/config/rules
hostname wwpxpsdb04 - profile -
root@wwpxpssc01-sc0 # ls -l /var/apache2/htdocs/wanboot/wanboot
-rw-r--r-- 1 root root 1090160 Oct 30 09:46 /var/apache2/htdocs/wanboot/wanboot

Ah! found it out... it was just a wrong location where I kept the wanboot-cgi file... it should have been in the <webserver root>/cgi-bin/ folder, but I wrongly kept in the "DocumentRoot"... All good now.
The error message from the previous error o/p should have been a bit more clear though..

Similar Messages

  • WANBOOT/Jet/Solaris 10 issues?

    I've tried booting via wanboot pure and cdrom method with the same results. I am using JET with a Solaris 10 01/06 and 06/06 images and have the same problems. Anyone seen this or can comment?
    Below is the output from the install.
    Sun Fire V210, No Keyboard
    Copyright 2005 Sun Microsystems, Inc.  All rights reserved.
    OpenBoot 4.18.10, 4096 MB memory installed, Serial #72488173.
    Ethernet address 0:14:4f:52:14:ed, Host ID: 845214ed.
    Rebooting with command: boot cdrom  -o prompt -F wanboot - install   
    Boot device: /pci@1e,600000/ide@d/cdrom@0,0:f  File and args: -o prompt -F wanboot - install
    1000 Mbps FDX Link up
    <time unavailable> wanboot info: WAN boot messages->console
    <time unavailable> wanboot info: Default net-config-strategy: manual
    boot> host-ip=10.188.60.164
    boot> router-ip=10.188.60.1
    boot> subnet-mask=255.255.254.0
    boot> hostname=richie2
    boot> file=http://10.188.75.160:80/cgi-bin/wanboot-cgi
    Unknown variable 'file'; ignored
    boot> bootserver=http://10.188.75.160:80/cgi-bin/wanboot-cgi
    boot> go
    <time unavailable> wanboot progress: wanbootfs: Read 368 of 368 kB (100%)
    <time unavailable> wanboot info: wanbootfs: Download complete
    Wed Aug 30 13:21:16 wanboot progress: miniroot: Read 271740 of 271740 kB (100%)
    Wed Aug 30 13:21:16 wanboot info: miniroot: Download complete
    SunOS Release 5.10 Version Generic_118833-17 64-bit
    Copyright 1983-2005 Sun Microsystems, Inc.  All rights reserved.
    Use is subject to license terms.
    Hardware watchdog enabled
    Configuring devices.
    Network interface was configured manually.
    10.188.60.164
    /sbin/install-discovery: /etc/inet/hosts: cannot create
    Beginning system identification...
    Searching for configuration file(s)...
    Using sysid configuration file http://10.188.75.160:80/wanboot/jet/richie2/sysidcfg
    Search complete.
    Discovering additional network configuration...
    Completing system identification...
    Starting remote procedure call (RPC) services: done.
    System identification complete.
    Starting Solaris installation program...
    Searching for JumpStart directory...
    Using rules.ok from http://10.188.75.160:80/wanboot/jet/richie2.
    Checking rules.ok file...
    Using begin script: begin.wanboot
    Using profile: profile
    Using finish script: finish.wanboot
    Executing JumpStart preinstall phase...
    Executing begin script "begin.wanboot"...
    Getting the Jet Framework onsite...
    Calling Standard Utils/begin script
    Calling Standard Utils/begin script
    Installation of richie2 at 09:17 on 30-Aug-2006
    Loading JumpStart Server variables
    Loading JumpStart Server variables
    Loading Client configuration file
    Loading Client configuration file
    CUSTOM: Running custom begin script....
    CUSTOM: Running custom begin script....
    FLASH: Running flash begin script....
    FLASH: Running flash begin script....
    Execution of Utils/begin finished
    Execution of Utils/begin finished
    Begin script begin.wanboot execution completed.
    Searching for SolStart directory...
    Checking rules.ok file...
    Using begin script: install_begin
    Using finish script: patch_finish
    Executing SolStart preinstall phase...
    Executing begin script "install_begin"...
    Begin script install_begin execution completed.
    Processing profile
            - Opening Flash archive
            - Validating Flash archive
            - Selecting all disks
            - Configuring boot device
            - Using disk (c1t0d0) for "rootdisk"
            - Configuring / (c1t0d0s0)
            - Configuring swap (c1t0d0s1)
            - Configuring /usr (c1t0d0s3)
            - Configuring /var (c1t0d0s4)
            - Configuring  (c1t0d0s7)
            - Configuring  (c1t1d0s7)
            - Configuring  (c1t0d0s5)
    Verifying disk configuration
            - WARNING: Unused disk space (c1t1d0)
            - WARNING: Changing the system's default boot device in the EEPROM
    Verifying space allocation
    Preparing system for Flash install
    Configuring disk (c1t0d0)
            - Creating Solaris disk label (VTOC)
    Configuring disk (c1t1d0)
            - Creating Solaris disk label (VTOC)
    Creating and checking UFS file systems
            - Creating / (c1t0d0s0)
            - Creating /usr (c1t0d0s3)
            - Creating /var (c1t0d0s4)
    Beginning Flash archive processing
    Predeployment processing
    16 blocks
    16 blocks
    16 blocks
    No local customization defined
    Extracting archive: sol_10_06_06
            Extracted    0.00 MB (  0% of 1591.77 MB archive)
            Extracted    1.05 MB (  0% of 1591.77 MB archive)
            Extracted    2.05 MB (  0% of 1591.77 MB archive)
            Extracted    3.05 MB (  0% of 1591.77 MB archive)
            <snipped>
            Extracted 1591.77 MB (100% of 1591.77 MB archive)
            Extraction complete
    Postdeployment processing
    No local customization defined
    Customizing system files
            - Mount points table (/etc/vfstab)
            - Network host addresses (/etc/hosts)
    ERROR: Could not open file (/etc/hosts)
    ERROR: Could not set up the remote host file (/etc/hosts)
    ERROR: Flash installation failed
    Solaris installation program exited.
    #

    Check your boot image
    /export/install/media/10u5/Solaris_10/Tools/Boot/etc/inet
    for the following links
    lrwxrwxrwx 1 root root 32 Sep 2 15:00 netmasks -> ../../tmp/root/etc/inet/netmasks
    lrwxrwxrwx 1 root root 31 Sep 2 15:00 ipnodes -> ../../tmp/root/etc/inet/ipnodes
    lrwxrwxrwx 1 root root 29 Sep 2 15:00 hosts -> ../../tmp/root/etc/inet/hosts
    I have seen a similar problem today where links were replaced by files causing an identical error
    Andrew

  • Using directory alias with a wanboot installation

    I have setup a Jumpstart server and have been using it for a while without issues. Now I want to incorporate wanboot into the process so that I do not need boot servers in each of our subnets. Since the jumpstart directory structure is already in place and I have apache running on the same server, I did not want to have to recreate the whole jumpstart directory structure. So I decided to create an alias in the apache configuration for the jumpstart directory:
    root@swamphenxb:/usr/local/apache2/conf> cat httpd.conf
    <snip>
    # ScriptAlias: This controls which directories contain server scripts.
    # ScriptAliases are essentially the same as Aliases, except that
    # documents in the target directory are treated as applications and
    # run by the server when requested rather than as documents sent to the
    # client. The same rules about trailing "/" apply to ScriptAlias
    # directives as to Alias.
    Alias /jumpstart /export/jumpstart
    ScriptAlias /cgi-bin/ "/usr/local/apache2/cgi-bin/"
    </IfModule>
    <IfModule cgid_module>
    # ScriptSock: On threaded servers, designate the path to the UNIX
    # socket used to communicate with the CGI daemon of mod_cgid.
    #Scriptsock logs/cgisock
    </IfModule>
    # "/usr/local/apache2/cgi-bin" should be changed to whatever your ScriptAliased
    # CGI directory exists, if you have that configured.
    <Directory "/usr/local/apache2/cgi-bin">
    AllowOverride None
    Options None
    Order allow,deny
    Allow from all
    </Directory>
    *<Directory /export/jumpstart>*
    AllowOverride None
    Options All
    Order allow,deny
    Allow from all
    *</Directory>*
    The wanboot.conf file is located in /etc/netboot and looks with the following information:
    root@swamphenxb:/usr/local/apache2/conf> cat /etc/netboot/wanboot.conf
    # Copyright 2004 Sun Microsystems, Inc. All rights reserved.
    # Use is subject to license terms.
    # ident "@(#)wanboot.conf.sample 1.2 04/01/30 SMI"
    # wanboot.conf(4): boot configuration file.
    # Please consult wanboot.conf(4) for further information. Note that
    # this interface is "Evolving" as defined by attributes(5).
    # Anything after a '#' is comment. Values may be quoted (e.g. "val").
    # <empty> means there is no value, i.e. null. The absence of any
    # parameter implies that it takes a default value (<empty> unless
    # otherwise specified).
    # <url> is of the form http://... or https://...
    # The path of the bootstrap file (within htdocs) which is served up
    # by wanboot-cgi(bootfile).
    boot_file=/jumpstart/wanboot/wanboot.s10_sparc # <absolute pathname>
    # These are used by wanboot-cgi(bootfile|bootfs|rootfs) to determine
    # whether boot_file or the bootfs is to be sent encrypted/signed, or
    # root_file is to be sent signed; the client must be setup with the
    # corresponding encryption/signature key(s) (which cannot be auto-
    # matically verified).
    # If an encryption_type is specified then a signature_type must also
    # be specified.
    encryption_type= # 3des | aes | <empty>
    signature_type= # sha1 | <empty>
    # This is used by wanboot-cgi(bootfs) and wanboot to determine whether
    # server authentication should be requested during SSL connection
    # setup.
    server_authentication=no # yes | no
    # This is used by wanboot-cgi(bootfs) and wanboot to determine whether
    # client authentication should be requested during SSL connection
    # setup. If client_authentication is "yes", then server_authentication
    # must also be "yes".
    client_authentication=no # yes | no
    # wanboot-cgi(bootfs) will construct a hosts file which resolves any
    # hostnames specified in any of the URLs in the wanboot.conf file,
    # plus those found in certificates, etc. The following parameter
    # may be used to add additional mappings to the hosts file.
    resolve_hosts= # <hostname>[,<hostname>*] | <empty>
    # This is used to specify the URL of wanboot-cgi on the server on which
    # the root_file exists, and used by wanboot to obtain the root server's
    # URL; wanboot substitutes root_file for the pathname part of the URL.
    # If the schema is http://... then the root_file will be signed if there
    # is a non-empty signature_type. If server_authentication is "yes", the
    # schema must be https://...; otherwise it must be http://...
    root_server=http://170.12.14.240/cgi-bin/wanboot-cgi # <url> | <empty>
    # This is used by wanboot-cgi(rootfs) to locate the path of the
    # rootfs image (within htdocs) on the root_server.
    root_file=/jumpstart/miniroot/miniroot # <absolute pathname> | <empty>
    # This is used by wanboot to determine the URL of the bootserver
    # (and whether bootlog traffic should be sent using http or https),
    # or whether it should simply be sent to the console.
    boot_logger= # <url> | <empty>
    # This is used by the system startup scripts. If set, it should
    # point to a file that contains name value pairs to be used at
    # start up time. For example, this file may be used to provide
    # install the values for sysidcfg and jumpscfg.
    system_conf=system.conf
    I have the client configured to boot from the web server and when I attempt to boot, I get the following message:
    {2} ok boot net - install
    Boot device: /pci@9,700000/pci@2/network@0 File and args: - install
    /pci@9,700000/pci@2/network@0: 1000 Mbps full duplex link up
    HTTP: Bad Response: 500 Internal Server Error (boot_file missing)
    Boot load failed
    I am able to see a listing of all the directories and files including the boot_file in my browser. The permissions for the /etc/netboot directory is:
    root@swamphenxb:/etc/netboot> ls -al
    total 26
    drwx------ 3 daemon other 512 Nov 20 13:09 .
    drwxr-xr-x 63 root sys 6144 Nov 2 11:43 ..
    drwx------ 3 daemon other 512 Nov 20 13:10 170.12.144.0
    -rw------- 1 daemon other 80 Nov 5 17:02 system.conf
    -rw------- 1 daemon other 3331 Nov 2 14:07 wanboot.conf
    It looks like maybe wanboot does not like the alias I am using, but I want to verify that before I move on to plan B. Thanks.
    Chuck Briggs

    Long but this is a copy of my lab configuration files for WAN boot
    */etc/ethers*
    0:3:ba:16:99:f5 wgls01
    0:3:ba:14:b9:71 wgls02
    0:3:ba:16:a5:bf wgls03
    0:3:ba:5b:c7:5b wgls04
    0:3:ba:16:9d:31 wgls05
    0:3:ba:e8:65:9 wgls07
    0:3:ba:e8:92:a9 wgls08
    0:3:ba:16:6b:27 wgls09
    0:3:ba:2b:35:c2 wgls10
    0:3:ba:5c:b0:5 wgls11*/etc/bootparams*
    wgls01 root=wgls06:/js/sparc/Solaris_10_2009-10/Solaris_10/Tools/Boot install=wgtsinf01:/js/sparc/Solaris_10_2009-10 boottype=:in   rootopts=:rsize=8192
    wgls02 root=wgls06:/js/sparc/Solaris_9_2005-09/Solaris_9/Tools/Boot   install=wgtsinf01:/js/sparc/Solaris_9_2005-09  boottype=:in   rootopts=:rsize=8192
    wgls03 root=wgls06:/js/sparc/Solaris_10_2009-10/Solaris_10/Tools/Boot install=wgtsinf01:/js/sparc/Solaris_10_2009-10 boottype=:in   rootopts=:rsize=8192
    wgls04 root=wgls06:/js/sparc/Solaris_10_2009-10/Solaris_10/Tools/Boot install=wgtsinf01:/js/sparc/Solaris_10_2009-10 boottype=:in   rootopts=:rsize=8192
    wgls05 root=wgls06:/js/sparc/Solaris_9_2005-09/Solaris_9/Tools/Boot   install=wgtsinf01:/js/sparc/Solaris_9_2005-09  boottype=:in   rootopts=:rsize=8192
    wgls06 root=wgls06:/js/sparc/Solaris_10_2009-10/Solaris_10/Tools/Boot install=wgtsinf01:/js/sparc/Solaris_10_2009-10 boottype=:in   rootopts=:rsize=8192
    wgls07 root=wgls06:/js/sparc/Solaris_10_2009-10/Solaris_10/Tools/Boot install=wgtsinf01:/js/sparc/Solaris_10_2009-10 boottype=:in   rootopts=:rsize=8192
    wgls08 root=wgls06:/js/sparc/Solaris_10_2009-10/Solaris_10/Tools/Boot install=wgtsinf01:/js/sparc/Solaris_10_2009-10 boottype=:in   rootopts=:rsize=8192
    wgls09 root=wgls06:/js/sparc/Solaris_8_2004-02/Solaris_8/Tools/Boot   install=wgtsinf01:/js/sparc/Solaris_8_2004-02  boottype=:in   rootopts=:rsize=8192
    wgls10 root=wgls06:/js/sparc/Solaris_10_2009-10/Solaris_10/Tools/Boot install=wgtsinf01:/js/sparc/Solaris_10_2009-10 boottype=:in   rootopts=:rsize=8192*/etc/hosts*
    # Fake prod subnet
    #10.64.86.30     wgls01.nz.thenational.com wgls01
    #10.64.86.31     wgls02.nz.thenational.com wgls02
    10.64.86.32     wgls03.nz.thenational.com wgls03
    10.64.86.33     wgls04.nz.thenational.com wgls04
    10.64.86.34     wgls05.nz.thenational.com wgls05
    10.64.86.35     wgls06.nz.thenational.com wgls06
    10.64.86.36     wgls07.nz.thenational.com wgls07
    #10.64.86.37     wgls08.nz.thenational.com wgls08
    #10.64.86.42     wgls09.nz.thenational.com wgls09
    10.64.86.43     wgls10.nz.thenational.com wgls10Under wgls06:/js/sparc I have many small (~85MB) directories just to load the boot code
    # find /js/sparc/Solaris_10_2008-10
    /js/sparc/Solaris_10_2008-10
    /js/sparc/Solaris_10_2008-10/Solaris_10
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers/solarisn
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers/liveupgrade20
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers/.install
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers/.install/solarisn.class
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers/.install/JRE
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers/.install/liveupgrade20.class
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers/.install/com
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers/.install/com/sun
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers/.install/com/sun/launcher
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers/.install/com/sun/liveupgrade
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Installers/.install/install_common
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/rm_install_client
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/add_install_client
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/pkg_db.cpio.bz2
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/X_small.cpio.bz2
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4us
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4us/inetboot
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4us/wanboot
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4us/boot_archive
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4u
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4u/boot_archive
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4u/inetboot
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4u/wanboot
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4v
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4v/wanboot
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4v/inetboot
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/platform/sun4v/boot_archive
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/netmask
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/X.cpio.bz2
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/lu.platforms
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/Boot/lu.cpio.bz2
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/.wanboot_unneeded_packages
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/setup_install_server
    /js/sparc/Solaris_10_2008-10/Solaris_10/Tools/dialAll OS files are located at wgtsinf01:/js/sparc
    Firewalls should allow the traffic (TFTP)

  • Size limit for flar file with Sol 10 WANBOOT

    There seems to be some kind of a size limit for flash archive files used by wanboot. When I try to wanboot jumpstart, I get the following:
    Processing profile
    - Opening Flash archive
    ERROR: HTTP server returned an invalid archive file size: <-1256985017> bytes
    ERROR: Invalid HTTP headers were returned from the server
    ERROR: Flash installation failed
    Solaris installation program exited.
    The flash archive is about 3GB. I'm doing the WANBOOT using the "boot cdrom" work-around, because the V100 I'm jumpstarting doesn't support the newer OBP parameters.
    If create a new smaller flash archive like so:
    mv sol10.flar sol10.flar.old
    dd if=sol10.flar.old of=sol10.flar bs=1024K count=1024
    cutting the flar down to 1GB. Then I do the wanboot. I don't get the error, and the jumpstart proceeds. Of course it would eventually have a problem when the cpio file reached premature end.
    So is there a prescribed limit to flars with WANBOOT. I'm assuming it's 2GB, but if so, why?
    No I haven't tried creating a compressed flar: that's next.
    Thanks,
    Chip Bennett
    Laurus Technologies, Inc.
    Itasca, IL

    nope, 64-bit apache2.2 and still the same error:
    Processing profile
    - Opening Flash archive
    HTTP server returned an invalid archive file size:
    <-2116410290> bytes
    ERROR: Invalid HTTP headers were returned from the
    server
    ERROR: Flash installation failed
    Solaris installation program exited.
    apache log:
    192.168.224.112 - - [06/Jul/2006:20:52:45 +0200]
    "HEAD /flash/archives/pt_sol_10_oem.flar HTTP/1.1"
    200 -
    192.168.224.112 - - [06/Jul/2006:20:52:45 +0200] "GET
    /cgi-bin/bootlog-cgi?%3Ctime%3E+wanboot_client+ident:+
    %5BID+380565+user.panic%5D+HTTP+server+returned+an+inv
    alid+archive+file+size:+%3C-2116410290%3E+bytes
    HTTP/1.1" 200 32
    192.168.224.112 - - [06/Jul/2006:20:52:45 +0200] "GET
    /cgi-bin/bootlog-cgi?%3Ctime%3E+wanboot_client+ident:+
    %5BID+592631+user.panic%5D+Invalid+HTTP+headers+were+r
    eturned+from+the+server HTTP/1.1" 200 32
    192.168.224.112 - - [06/Jul/2006:20:52:45 +0200] "GET
    /cgi-bin/bootlog-cgi?%3Ctime%3E+wanboot_client+ident:+
    %5BID+915281+user.panic%5D+Flash+installation+failed
    HTTP/1.1" 200 32
    Any help would be much appreciated.hi. i spent a long time on this issue...and got it working reliably for more than 10 gb flars.
    there are two issues- 1) apache must be 64 bit capable, and 2) you need the latest wanboot miniroot, for solaris 9 and one for solaris 10. i worked for a different division of a major car company based in stuttgart (take a guess) than i do now, and we eventually received the support we needed from sun, through the early release program. i do not know any details about if, how, or when those miniroots are otherwise available. at some point, i can only assume they will be generally available to all, if not already.
    if someone knows more about this availability issue, i would also be interested in this issue.
    thanks, dls

  • WAN boot Server issues.

    I 'm getting following error while booting client from WAN boot server.
    {0} ok setenv network-boot-arguments host-ip= 10.63.25.208 ,router-ip= 10.63.24.1 ,subnet-mask= 255.255.252.0 hostname=xxxxxx-u012 ,filename=http://10.63.25.180/cgi-bin/wanbnetwork-boot-arguments = host-ip= 10.63.25.208 ,router-ip= 10.63.24.1 ,subnet-mask= 255.255.252.0 hostname=essapl020-u012 ,filename=http://10.63.25.180/cgi-bin/wanboot-cgi
    {0} ok boot net - install
    Boot device: /pci@0/pci@0/pci@1/pci@0/pci@2/network@0 File and args: - install
    Improperly formatted value for 'host-ip'
    ERROR: boot-read fail

    dedwards wrote:
    I am having cronic issues with the WAN port reporting that it is unplugged. The Time Capsule LED is flashing amber when this happens.
    When that happens do you see a tiny green light next to the WAN port socket on the Time Capsule?
    You might try reversing that Ethernet cable end-for-end or trying a different cable.

  • New DVR Issues (First Run, Channel Switching, etc.)

    I've spent the last 30 minutes trying to find answers through the search with no luck, so sorry if I missed something.
    I recently switched to FIOS from RCN cable in New York.  I've gone through trying to setup my DVR and am running into issues and was hoping for some answers.
    1.  I setup two programs to record at 8PM, I was watching another channel at the time and only half paying attention.  Around 8:02 I noticed a message had popped up asking if I would like to switch channels to start recording.  I was expecting it to force it to switch like my old DVR, but in this case it didn't switch and I missed the first two minutes of one of the shows.  I typically leave my DVR on all day and just turn off the TV, this dual show handling will cause issues with that if I forget to turn off the DVR.  Is there a setting I can change that will force the DVR to choose one of the recording channels?
    2.  I setup all my recordings for "First Run" because I only want to see the new episodes.  One show I setup was The Daily Show on comedy central, which is shown weeknights at 11pm and repeated 3-4 times throughout the day.  My scheduled recordings is showing all these as planned recordings even though only the 11pm show is really "new".  Most of the shows I've setup are once a week so they aren't a problem, but this seems like it will quickly fill my DVR.  Any fixes?
    Thanks for the help.
    Solved!
    Go to Solution.

    I came from RCN about a year ago.  Fios is different in several ways, not all of them desirable.  Here are several ways to get--and fix--unwanted recordings from a series recording setup.
    Some general principles. 
    Saving changes.  When you originally create a series with options, or if you go back to edit the options for an existing series, You MUST save the Series Options changes.  Pretty much everywhere else in the user interface, when you change an option, the change takes effect immediately--but not in Series Options.  Look at the Series Options window.  Look at the far right side.  There is a vertical "Save" bar, which you must navigate to and click OK on to actually save your changes.  Exiting the Series Options window without having first saved your changes loses all your attempted changes--immediately.
    Default Series Options.  This is accessed  from [Menu]--DVR--Settings--Default Series Options.  This will bring up the series options that will automatically be applied to the creation of a NEW series. The options for every previously created series will not be affected by a subsequent modification of the Default Series Options.  You should set these options to the way you would like them to be for the majority of series recordings that you are likely to create.  Be sure to SAVE your changes.  This is what you will get when you select "Create Series Recording" from the Guide.  When creating a new series recording where you think that you may want options different from the default, select "Create Series with Options" instead.  Series Options can always be changed for any individual series set up later--but not for all series at once.
    Non-series recordings.  With Fios you have no directly available options for these.  With RCN and most other DVRs, you can change the start and end times for individual episodes, including individual episodes that are also in a series.  With Fios, your workarounds are to create a series with options for a single program, then delete the series later;  change the series options if the program is already in a series, then undo the changes you made to the series options later; or schedule recordings of the preceding and/or following shows as needed.
    And now, to the unwanted repeats. 
    First, make sure your series options for the specific series in question--and not just the series default options--include "First Run Only".  If not, fix that and SAVE.  Then check you results by viewing the current options using the Series Manager app under the DVR menu.
    Second, and most annoying, the Guide can have repeat programs on your channel tagged as "New".  It happens.  Set the series option "Air Time" to "Selected Time".  To make this work correctly, you must have set up the original series recording after selecting the program in the Guide at the exact time of a first run showing (11pm, in your case), and not on a repeat entry in the Guide.  Then, even it The Daily Show is tagged as New for repeat showings, these will be ignored. 
    Third, another channel may air reruns of the program in your series recording, and the first showing of a rerun episode on the other channel may be tagged as "New".  These can be ignored in your series if you set the series option "Channel" to "Selected Channel".  Related to this, if there is both an SD and HD channel broadcasting you series program, you will record them both if the series option "Duplicates" is set to "Yes".  However, when the Channel option is set to "Selected Channel", the Duplicates Option is always effectively "No", regardless of what shows up on the options screen.  
    As for you missing two minutes,  I have sereral instances in which two programs start recording at the same time.  To the best of my recollection, whenever the warning message has appeared, ignoring it has not caused a loss of recording time.  You might have an older software version.  Newest is v.1.8.  Look at Menu--Settings--System Info.  Or, I might not have noticed the loss of minutes.  I regularly see up to a minute of previous programming at the start of a recording, or a few missing seconds at the beginning or end of a recording.  There are a lot of possibilities for that, but the DVR clock being incorrect is not one of them.  With RCN, the DVR clocks occasionally drifted off by as much as a minute and a half.

  • Pension issue Mid Month Leaving

    Dear All,
    As per rule sustem should deduct mid month joining/leaving/absences or transfer scenarios, the Pension/PF Basis will be correspondingly prorated. But our system is not doing this. In RT table i have found 3FC Pension Basis for Er c 01/2010                    0.00           6,500.00.
    Employee leaving date is 14.04.2010. system is picking pension amout as 541. Last year it was coming right.
    Please suggest.
    Ashwani

    Dear Jayanti,
    We required prorata basis pension in case of left employees and system is not doing this. This is the issue. As per our PF experts Pension amount should come on prorata basis for left employees in case they left mid of month.System is doing prorata basis last year but from this year it is deducting 541. I am giving two RT cases of different years.
    RT table for year 2010. DOL 26.04.2010
    /111 EPF Basis              01/2010                    0.00           8,750.00 
    /139 VPF Basis              01/2010                    0.00           8,750.00 
    /3F1 Ee PF contribution     01/2010                    0.00           1,050.00 
    /3F3 Er PF contribution     01/2010                    0.00             509.00 
    /3F5 Ee Mon PF contribution 01/2010                    0.00           1,050.00 
    /3F6 Ee Ann PF contribution 01/2010                    0.00          12,600.00 
    /3F9 PF adm chrgs * 1,00,00 01/2010                    0.00              96.25 
    /3FA PF basis for Ee contri 01/2010                    0.00           8,750.00 
    /3FB PF Basis for Er Contri 01/2010                    0.00           8,750.00 
    /3FJ VPF basis for Ee contr 01/2010                    0.00           8,750.00 
    /3FL PF Basis for Er Contri 01/2010                    0.00           6,500.00 
    /3F4 Er Pension contributio 01/2010                    0.00             541.00
    /3FC Pension Basis for Er c 01/2010                    0.00           6,500.00
    /3FB PF Basis for Er Contri 01/2010                    0.00           8,750.00
    /3FC Pension Basis for Er c 01/2010                    0.00           6,500.00
    /3FJ VPF basis for Ee contr 01/2010                    0.00           8,750.00
    /3FL PF Basis for Er Contri 01/2010                    0.00           6,500.00
    /3R3 Metro HRA Basis Amount 01/2010                    0.00           8,750.00
    1BAS Basic Salary           01/2010                    0.00           8,750.00
    RT table for year 2009. DOL 27.10.2009
                                                                                    /111 EPF Basis              07/2009                    0.00           9,016.13
    /139 VPF Basis              07/2009                    0.00           9,016.13
    /3F1 Ee PF contribution     07/2009                    0.00           1,082.00
    /3F3 Er PF contribution     07/2009                    0.00             628.00
    /3F5 Ee Mon PF contribution 07/2009                    0.00           1,082.00
    /3F6 Ee Ann PF contribution 07/2009                    0.00           8,822.00
    /3F9 PF adm chrgs * 1,00,00 07/2009                    0.00              99.18
    /3FA PF basis for Ee contri 07/2009                    0.00           9,016.00
    /3FB PF Basis for Er Contri 07/2009                    0.00           9,016.00
    /3FJ VPF basis for Ee contr 07/2009                    0.00           9,016.00
    /3FL PF Basis for Er Contri 07/2009                    0.00           5,452.00
    /3FB PF Basis for Er Contri 07/2009                    0.00           9,016.00 
    /3FC Pension Basis for Er c 07/2009                    0.00           5,452.00 
    /3FJ VPF basis for Ee contr 07/2009                    0.00           9,016.00 
    /3FL PF Basis for Er Contri 07/2009                    0.00           5,452.00 
    /3R4 Non-metro HRA Basis Am 07/2009                    0.00           9,016.13 
    1BAS Basic Salary           07/2009                    0.00           9,016.13 
    Now please suggest what to do. where is the problem  ? If have also checked EXIT_HINCALC0_002 but nothing written in it.
    With Regards
    Ashwani

  • Open PO Analysis - BW report issue

    Hello Friends
    I constructed a query in BW in order to show Open Purchase Orders. We have custom DSO populated with standard
    datasource 2lis_02_itm (Purcahse Order Item). In this DSO we mapped the field ELIKZ to the infoobject 0COMP_DEL
    (Delivery completed).
    We loaded the data from ECC system for all POs and found the following issue for Stock Transport Purchase orders (DocType = UB).
    We have a PO with 4 line items. For line items 10 and 20, Goods issued, Goods received and both the flags "Delivery
    complete" and "Final delivery" checked. For line items 30 and 40, only delivery indicator note is issued for zero
    quantity and Delivery complete flag is checked (Final delivery flag is not checked) in ECC system. For this PO, the
    delivery completion indicator is not properly updated in the DSO for line items 30 and 40. The data looks like the
    following:
    DOC_NUM     DOC_ITEM       DOCTYPE     COMP_DEL
    650000001       10     UB        X
    650000001       20     UB        X
    650000001       30     UB
    650000001       40     UB      
    When we run the Open PO analysis report on BW side this PO is appearing in the report but the same is closed in ECC
    system.
    Any help is appreciated in this regard.
    Thanks and Regards
    sampath

    Hi Priya and Reddy
       Thanks for your response.
                         Yes the indicator is checked in EKPO table for items 30 and 40 and delta is running regularly for more than 1 year and no issues with other POs. This is happening only for few POs of type Stock Transport (UB).
                        I already checked the changes in ME23N and the Delivery completed indicator was changed and it reflected in EKPO table. Further, i checked the PSA records for this PO and i am getting the records with the Delivery completed flag but when i update from PSA to DSO the delivery completed indicator is not updating properly.
                       In PSA, for item 30 i have the following entries. Record number 42 is capturing the value X for ELIKZ but after that i am getting two more records 43 and 44 with process key 10 and without X for ELIKZ. I think this is causing the problem.
    Record No.    Doc.No.                    Item              Processkey         Rocancel     Elikz
        41               6500000001            30                    11                            X           ---    
        42               6500000001            30                    11                            ---           X
        43               6500000001            30                    10                            X           ---
        44               6500000001            30                    10                            ---         ---
    (Here --- means blank)        
    Thanks and Regards
    sampath

  • HP LaserJet Enterprise 600 M602 driver issue

    Hello,
    I've got issue with 600-series printers. We use the latest UPD drivrer ver. 61.175.1.18849 and print from XenApp 6.5. The error occurs every time when users try to print jpg files from XenApp session. It only happens with 600 series printers and UPD.
    Also I've tried to assign native 600-series driver ver. 6.3.9600.16384 and it works good. But with that driver system says that it's color printer and it brokes our printing reports. These reports are very important for us. So we can't use printer and that driver as well.
    Printer installed on Windows Server 2012 R2. All clients are Windows 7 x64. XenApp Servers are Server 2008R2.
    Is it possible to get fixed UPD driver or correct native driver for Server 2012 R2?
    Regards,
    Anatoly

    I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial printer. You can do this at Printers - LaserJet.
    Click on New Post.
    I hope this helps.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Windows 7 displays error message when exiting +cursor issue

    Two issues here. CS5 Phoshop on Wind 7 64 bit.
    Physical processor count: 8
    Processor speed: 3073 MHz
    Built-in memory: 12279 MB
    Free memory: 9577 MB
    Memory available to Photoshop: 10934 MB
    Memory used by Photoshop: 80 %
    Image tile size: 128K
    First issue is since the latest automatic Adobe update (why fix what isn't broken?) Every time I now exit Photoshop I get the message "Adobe QT Server has stoped working" and occasionally it happens when I exit bridge. Indesign is also behaving badly. I can no longer start a previous document from file manager without ID crashing out.
    The other is the cursors in Clone and erase lose their edge (become invisable) for no reason - well not quite. Noise Ninja crashed Photoshop when I tried to use it. I reinstalled it and all is well. The cursor issue seems to be intermittant but came back (for no reason) after I reinstalled NN. I can't seem to change the cursor, no matter what I do. The problem is now seriously affecting how I work. Almost enough to go back to Win XP which ran CS5 Photoshop flawlessly.
    Any help will be gratefully accepted.
    Doug

    function(){return A.apply(null,[this].concat($A(arguments)))}
    doug87510 wrote:
    The recent problem is the entire outline of the cursor (including the crosshair in the middle) was missing at any size of cursor. All I had was exactly what I'd get if I used a real spraygun.
    Well, that issue is simply a matter of hitting the Caps Lock key.  When Caps Lock is on, you'll see the cursor outline, and when it is off you'll see a crosshair.  That's a feature, not a bug.
    Glad to hear the 11.1 drivers are out.  I will download them and try them now myself.
    Regarding "Adobe QT" crashing...  QT brings to mind QuickTime, though that is Apple, not Adobe.  Do you have Apple QuickTime installed?
    Regarding memory usage, with 12 GB of installed RAM, you should be able to set Photoshop to use 90% or more in Edit - Preferences - Performance.
    -Noel

  • Issue in Creation of Periodicals for Contracts in CRM7.0

    Hello,
    I have a requirement to create Contracts in CRM7.0 system.
    And I am doing this using the BAPI *BAPI_BUSPROCESSND_CREATEMULTI*
    Good part is Contract Order gets created, but onlywith Header Details.
    The issues i am facing --
    1. I need to know what kind/type of data must be passed to the interface parameters, the F1 Help/Documentation is vague.
    2. I am passing data in the INPUT FIELDS structure with the Object ID, Handle Number, Reference GUID and Fieldname,
        here what does 'Logical Key' field indicate? What should be passed here.
        What does 'REFERENCE KIND' field indicate, i have been passng 'A' for everything (to be frank i dont know whats its significance is!!).
    3. With so much, My Order gets created but with less than half details, i.e. the Objects not getting created are -  Partner, Product, terms/appointments, Status, LongTexts......
    Any help/inputs would be appreciated.
    Hope my problem is stated clearly ...
    --Regards
    Dedeepya

    Hi Anu,
    i found my solution by debugging with existing data or while creating it in CRMD_ORDER.
    Ensure that you are passing a correct entry in INPUT_FIELDS structure.
    As i haven't worked on rebates i woudlnt be able to help you, I suggest you debug to arrive at a solution.
    You can preset your break-points at :-
    1. FM - CRM_ORDER_MAINTAIN
    2. CRM_ORDER_MAINTAIN_MULTI_OW -- Debug through the complete FM.
    3. CRM_ORDER_PREPARE_MULTI_OW -- The data is set in this function module.
    Regards
    Dedeepya C

  • Issue in creation of plant related data at receiving server using BD10

    Hi all,
    This is regarding Material master creation using B10.I am using MATMAS05 message type for sending data from one system to another.Data is sent and received successfully.When i go in mm03 i can see all the views created successfully accept views related to PLANT.Please guide to resolve the issue.
    When i entered into Log-
    1)"The field MBEW-BKLAS is defined as a required field; it does not contain an entry".
    2)"No material master data exists for material AB_08.04.09(30) in plant 4001".
    My segemnt is as follows-
    ZMATMAS05                      matmas05
           E1MARAM                        Master material general data (MARA)
               Z1KLART                        KLART----
    My extention
               E1MARA1                        Additional Fields for E1MARAM
               E1MAKTM                        Master material short texts (MAKT)
               E1MARCM                        Master material C segment (MARC)
                   Z1AUSPM                        E1AUSPMDistribution of Classification:----
    My extention
                   E1MARC1                        Additional Fields for E1MARCM
                   E1MARDM                        Master material warehouse/batch segment (MARD)
                   E1MFHMM                        Master material production resource/tool (MFHM)
                   E1MPGDM                        Master material product group
                   E1MPOPM                        Master material forecast parameter
                   E1MPRWM                        Master material forecast value
                   E1MVEGM                        Master material total consumption
                   E1MVEUM                        Master material unplanned consumption
                   E1MKALM                        Master material production version
               E1MARMM                        Master material units of measure (MARM)
               E1MBEWM                        Master material material valuation (MBEW)
               E1MLGNM                        Master material material data per warehouse number (MLGN)
               E1MVKEM                        Master material sales data (MVKE)
               E1MLANM                        Master material tax classification (MLAN)
               E1MTXHM                        Master material long text header
               E1CUCFG                        CU: Configuration data
           E1UPSLINK                      Reference from Object to Superior UPS
    Thanks.
    Edited by: sanu debu on Apr 27, 2009 7:10 PM

    CREATE CONTROLFILE SET DATABASE "NEWDB" NORESETLOGS ARCHIVELOGAlso when you are setting a new database, the option should be RESETLOGS and not NORESETLOGS.
    'D:\APP\ADMINISTRATOR\ORADATA\NEWDB\ONLINELOG\O1_MF_2_7FK0XKB8_.LOG
    D:\APP\ADMINISTRATOR\ORADATA\NEWDB\DATAFILE\O1_MF_SYSTEM_7FK0SKN0_.DBFWhy underscore(_) at the end of the datafile name. Any specific reason ?

  • Issue in Creation of new Value Field in CO-PA

    Hi,
    I have a query in CO-PA Value Field Linking.
    In my Development Client,
    1. Created a New Value Field (No Transport Request Generated)
    2. Linked to the above to new Conditon type created in SD. (Tranport request was generated) i.e. in Flow of Actual Values->Transfer of Billing Documents->Assign Value Fields
    However then i try creating a new Value Field in my Production Client it throws a message 'You have no authorization to change Fields".
    Is this an issue with authorization or i need to transport the Value field too from Development to Production client.
    Please Advise.
    Thanks in Advance,
    Safi

    Thanks Phaneendra for the response.
    The creation of Value field did not create any tranportation request. Will this too be transported if i transport the Operating Concern.
    Please Advise.
    Thanks,
    Safi

  • Issue of Free Goods

    Dear All
    I have some is my current assignment-Customer is buying some material say "A" want "B,C" as exclusive free goods
    is it possible to give two free at a time in same order ?
    I only know one exlusive free good can be give to one material with combination of customer ( Customer/Material)
    Looking for some inputs regarding the issue.
    Can you plz suggest me if there is any possiblities for BOM?
    Many Thanks
    Rakesh Naveen

    Dear Rakesh,
    Be informed that free goods is not currently supported in combination with material structures (e.g. product selection,     
    bills of material, variants with BOM explosion), see note 796926.   
    Determination of free goods is performed in include FV45PF0N_NATRAB_SELECTION and the check is hardcoded. You will have to modify the program to get that functionality, but be carfull that any modification won't be supported by SAP, see note 170183.                
    I hope it can help you.
    Ruy Castro

  • Issue in creation of control cycle

    Dear Gurus,
    During creation of control cycle (LPK1), the fields for source information is not appearing in my system.
    I compared control cycle in a different ECC system where source information is appearing.
    How can make the screen appear in my ECC system.
    Please find the screenshots.
    Any pointers will be highly appreciated.
    This thread is further to the threads in Production Planning and LE/WM Forum. I could not resolve the issue with the threads.
    Hope that I will get any pointer in EWM forum.
    http://scn.sap.com/thread/3609441
    http://scn.sap.com/thread/3610822
    With Regards,
    Malay

    Hello Malay,
    Can first contact your ABAPer and ensure the bottom screen is not an Screen Enhancement?
    If it is a some custom development, your ABAPer can help you on the logic behind it.
    Else, Let us know.
    Regards,
    Sathish

Maybe you are looking for

  • Need helping tracking downloads

    Hi everyone! First off I'm a complete noobie when it comes to podcasting... I've had a podcast for over a year, however, I do not know anything about coding. I use a 3rd party app called Feeder to help me with my feeds. I have a podcast in iTunes (ht

  • Email Reply/New Message Error

    I have a really strange error ... I have 4 different email accounts on my iPhone and iPad and I set one of those accounts as the main account. The problem is that when I'm trying to reply to a mail he is always using my gmail account instead of my ma

  • Help Please: Slow To Restart After Update

    My family member got his Macbook in August 2006 but rarely if ever did any updates. I ran Software Update today and there were a lot of things listed so I decided to do it in steps. First, there were a couple of firmware updates which downloaded then

  • Can't enable DMA on cd rom drive

    Hey, How could I get my CD ROM drive, recognized as /dev/sr0, to get Direct Memory Access enabled? The reason for this is when I use mplayer to read from an audio CD, the cache gets emptied pretty fast (and without it, audio is too choppy to listen t

  • IPhone 4 naming convention

    Hi everybody, I'm interested in knowing how the iPhone comes up with its file names for photos taken with the camera. There appears to be a structure to it but I cannot nail it down exactly. In my control I have 3 photos. The first in the list was ta