Want comments on k8n neo2 platinum prior to buying it,

hi people.
im doing some research prior to buyng an amd64 motherboard and have been looking at this one.
MSI K8N NEO2 Platinum-54G Moderkort S939 nForce3 250Ultra,SATA,GbLAN,ATX,Dual-DDR
is the firewall good or bad ?
is the motherboard easy to work with ?
stable ?
anyone tried the new 3000+ and 3200+ on it ?
i would also want end user comments on it.
Good Night.
EDIT:
im going to most of the hardware found in my signature.
if the psu aint up to it i will use a second psu until i get money to buy a bigger one.

Hi Raven, missed this thread till now!! Congrats soon getting S-939 A64, that will be way less than 10lb shipping charge to mail you
My MSI K8N Neo2 NF3 250 Ultra has been stable from BIOS v1.0 upwards, no mis-fires, no overheats, no comm/USB/PS2 probs, smooth all the way, for me. Per reviews Gigabyte and Asus also good, MSI won Bmarks on reviewers reference boards.
Peeps reporting probs with board here though, so check out this nVidia section. The BIOS updates helped some.
-Zalman CNPS7000_ Al/Cu HSF screws right into the original backplate, keeps my FX53 at 34C Folding.
-CNPS7000A or B are good, peeps say ya' need to use the backplate came with the HSF. The mobo backplate comes off pretty easy. Edit: re Hansh's mod Zalmans.
-The stock AMD fan is fine at stock or low OC.
-No HSF install pix I've seen, even the monster TT heatpipe cooler, have interfered with RAM, but there's always an exception.
-Your Antec is prolly good enough, AMD rec's a reputable 350W or better. CPU uses ~90W (98?) Like ya say, if it isn't you always have the other one too
-NB fan is small but works well so far. It's noise doesn't compete with the other 8 fans
ps: Software only prob, Win XP doesn't like RAID 5 PCI cards at install.
=--
Hansh, Allreet!

Similar Messages

SATA HDD installation on K8N Neo2 Platinum, Non-RAID, Non-Bootable

Hi-
I’m a rank newbie on this forum (first post). I have a K8N Neo2 Platinum Mobo, which I’ve recently gotten up and running, with Windows XP-Pro SP2 installed on a single IDE drive. I would now like to add 2 SATA drives. I don’t need or want the SATA drives to operate in a RAID array, nor do I want them to be bootable. I want to use them independently for data storage. I read the following thread (I am posting here on a separate thread per the author’s wishes not to get his original thread too junked-up) :
Single SATA or Multiple Drive Array Setup FAQ
I have not yet plugged-in either of my SATA drives, because I don’t want to risk corrupting my existing boot (IDE) drive. I just had a few questions about the procedure given in the referenced thread, in the Single Drive Setup:
- Step 14 States: “Make sure the “RAID Mode” is Stripping and Striping Block at 64k or Optimal. Hit F7 (Finish)”. Is this correct for a single non-boot drive?
- Step 22 States: “As most of you know when you enter the Setup for Win2k/WinXP you will need to hit F6 to load additional drivers for other SCSI devices.” I assume this means I need to boot from the Windows CD. Is this true even if I already have Windows installed on an IDE HDD on this system? At what point will I need to hit <F6> ? Will I be prompted to do so?
- I have downloaded (from the MSI website) the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total). Should I put these on a floppy? Or can I access them from a directory on my OS HDD?
- Should I go ahead and plug-in both of the 2 SATA drives I want to add to the system before beginning the driver installation? The only reason I would consider installing them one at a time is if it eliminated any confusion between RAID vs. independent (I want independent operation). If I do install them one at a time, do I have to install the driver twice?
Any help would be appreciated.
- the bbdude

OK Thanks JeanGuy and ssjkakaroto,
I have connected both of my SATA drives. They are enabled in BIOS but not set to RAID. I booted up to Windows on my IDE drive. In Disk Manager, the display shows Disk 0 (C: System), Disk 1 and Disk 2 as uninitialized, and my DVD (D:) drive. At this point, I could probably go ahead and run the Initialize and Convert Disk Wizard to get these disks formatted and be dome with ot now. Before I do that though, I just have a couple of more questions.
- I had already loaded the nVidia nForce3 system driver prior to installing the SATA drives, but I went ahead and did that again after installing the SATA drives and restarting Windows. I used Live Update, which went out to the MSI site and found version 5.03 of the nVidia nForce3 system driver. I'm not sure how to find the "Nvidia 5.10 driver package which include the latest SATA driver", ssjkakaroto referred-to. The Live Update install procedure did ask if I wanted to install IDE driver and I said yes. It then asked to over-write what I already had there (I said yes to that too). As the file names streamed-by, I though I saw some filenames with nv... listed. So, bottom line, is I'm not sure if I have the lates and greatest nVidia SATA drivers installed. How can I find out what drivers are installed?
- As I mentioned in my previous post, I have also downloaded and unzipped the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total) from the MSI site; however, I don't know how to "install" this now that I have the files. There are a couple of .exe and a .bat file (bit no setup.exe).
I may already have everything I need to partition and format these drives. I just want to bve sure I'm not skipping a step that is essential to optimal performance.
Thanks -
- bbdude

Need help with k8n neo2 platinum

I've just installed a new k8n neo2 platinum s939 board with a venice core 3200+ cpu the htt is 2000 and multiplier 10x.
I've gone to the core cell menu and set the htt to 4x (seemed to be this at default) and the max mem clock at 166 (more about this in a moment), the fsb will go quite easily up to 250mhz even 255mhz, but when I try 260 Mhz the machine when it reboots shows the initial slash screen but then goes to a blank screen with the cursor flashing in the top left hand corner, I can't even get back into the bios setup without clearing the cmos.
The odd thing is that the adjust cpu vid is showing a voltage of 1.50 and not 1.40 or startup.
Anyway with the fsb at 250mhz the bios screen is showing the Current ddr clock at 208 mhz ( not the max memclock setting of 166) the memory in the motherboard ( a crucial 512meg ddr333 single stick) seems to perform OK according to memtest which shows no errors after 2 cycles.
Any attempt to get to 260mhz fsb appears to fail even by upping the cpu vid to 1.525v unless i adjust the cpu voltage setting which by default is set to (by cpu vid) to +3.3%. Doing this enables me to get to fsb 260mhz but the memtest fails ( even when I set the max memclock to 133, which shows my current ddr speed at 174mhz, well below the 208mhz which appeared stable with the fsb at 250mhz?)
So firstly why are there two cpu voltage settings in the bios when my manual only shows 1 (there is no mention of this cpu vid setting?
How is it that my memory is stable at 208mhz with a fsb of 255mhz but unstable at 174mhz with the fsb set at 260mhz?
Why does the memory clock lock not appear to be working, the memory should be fixed at 166mhz but infact increases with fsb?
I have bios revision 1.5.
Please help as I am not familiar with the bios settings for this nforce 3 chipset, they seem rather odd to me. I'm sure my venice core 3200+ cpu can get beyond 250mhz fsb, I have another pc with a venice core 3000+ cpu which runs quite happily at 270mhz fsb.
PS I've tried reducing the htt to 3x but the same thing happens.

OK further feed back, I can get to over 260mhz fsb but the system is not stable the memory runs OK with mem test but I have problems with prime95.
I had to up the cpu core voltage to 1.53v to get to 260mhz using the cpu voltage setting in the bios and setting a 5% increase. increasing the cpu vid setting to 1.55v did not seem to do anything at all the core voltage was still at 1.43v.
I upped the mem voltage to 2.6v from 2.5 but still could not get the system to be stable, it may be that the memory is holding the system back but I don't want to pay for better memory at the moment. Unless anyone has got any other ideas it looks like I may be forced to settle with 250mhz, well still a 500mhz increase maybe not that bad. I've now to try 3d benchmarking using my radeon 9600xt and 3dmark 03.

Prevent usb mouse starting pc from standby ( k8n Neo2 platinum )

I have a k8n neo2 platinum board and i have 2 mice connected, 1 is ps2 the other usb. What i want to do is stop the usb mouse starting the pc from standby, i looked in the bios but cant seem to find anyway to do this. Its a real pain, if the unit the pc is on is nudged by the chair or if someone pics something up and nudges the mouse the pc starts. Sometimes this happens of a night when ive gone to bed, i come down the next morning and the pc,s running. Its quite a quiet pc so if the tv,s on you dont always hear it start-up.

Ive just tried your suggestion now TheBigMan, i disabled everything and still the pc starts from the usb mouse. I have never known such messing about shutting down and starting up a pc. I really am starting to wish i had bought an asus board instead. Thanks for your input.

K8N Neo2 platinum & 750g sata RAID issue

Hi there I have an issue with booting up. I have 1 200g Western digital HDD where windows is installed and I have 1 further 500g WD drive which were both fine until I decided to buy 2 samsung 750g HDD's to run in RAID. I have installed the drives in RAID and formatted but I am having a problem with booting.
If I reset, the computer keeps rebooting at the detection stage, powers off and keeps doing it over and over. Sometimes it will go through if you wait long enough. When I turn the power on and off it will go through the detection stage no worries every time but then at the XP loading screen it will freeze there. Sometimes it goes through and I will boot into XP fine and other times I can't get in.
I have the latest Bios 7025V1D but I am wondering if this issue is bios related because of the 750g size... The problem has only started since I have installed the two 750g HDD's in RAID. Does this bios version support 750g HDD's? Is there an updated BIOS to fix this problem somewhere?
I have 2gig of ram, 3500+ processor, latest Nforce3 drivers from Nvidia, RAID drives on sata ports/3/4, 500gig WD on sata port 1, 200 gig WD is HDD is IDE, Windows SP2 and all updated, ummmmmm everything else is fine I'm fairly sure.
I had a few troubles installing the RAID drivers because windows didn't want to accept the drivers I downloaded from here and did not want to accept the drivers in windows. I ended up getting it the drives to come on-line through the use of START/NVIDIA corp/ NVIDIA RAID program (cant remember the name, typing this on another computer).
Any ideas would be greatly and very muchly appreciated!
Terry.

Ok My PSU is: WideTECH 550w, +3.3v=33a, +5v=36a, +12v=25a, -12v=1.0a, +5vsb=2.5a.
I am only running 3 HDD's at the moment, the 2 750's and the 1 200gig. I have left the other 500gig unplugged until I get this problem sorted. I don't have a cd rom plugged in or a floppy. I only connect them when I need to because this computer is setup to be a storage server and I use my other pc for anything dvd related etc. The only other thing which is chewing power is the video card which is an old 6800gt ultra. So basically the power issue was fine until I installed the two extra HDD's and as I have unplugged the 500gig for the time being its only really one extra HDD which shouldn't be an issue. Oh I have two 80mm case fans using the psu aswell.
As for my other specs: I have 1 gig of Geil dual channel RAM 2x512 sticks, CPU=AMD Athlon64 3500+, MB is MSI K8n Neo2 Platinum, Vid card= Leadtek geforce 6800gt ultra 256 agp, You know about my HDD's but here they are again= 1x 200g WD caviar IDE, 1x 500g WD caviar sata(1 I think), 2 x 750g samsung sata (2 I think), OS = XP Home SP2 with all lasest automatic updates, latest BIOS etc etc etc....
My windows is a legit copy as well.
You mentioned putting my HDD's into sata 1 mode... I was of the opinion that my motherboard does not support sata2 anyway and would not allow them to run in anything but sata1?? If I did want to change the sata mode where would I do this anyway?
Thanks for your reply but I don't think it has to do with psu or sata mode although I'm interested about this sata2 thing, please explain.
Thanks in advance,
Terry.

K8N-Neo2 Platinum pauses for 25 sec at boot, nvatabus.sys the problem?

All,
After POSTing normally and starting to load Windows XP, my system halts at the Windows XP splash screen for about 25 seconds. Nothing happens, no disk activity or anything, the system just sits there.
I used Microsoft's Bootvis utility to see what was happening. It turns out that the nvatabus.sys driver consumes 100% CPU at boot for 25 seconds then the system continues to boot normally. Does anyone else see anything like this?
I am running the latest nForce drivers from MSI. The driver in question:
NVIDIA nForce3 Serial ATA Controller 2.6
Driver Date 6/3/2004
c:\WINDOWS\System32\DRIVERS\nvatabus.sys 5.10.2600.0446
Windows XP SP1
I have a RAID1 of two 160 GB SATA drives. The mirror is healthy and working fine.
After booting the system is rock-solid stable, no problems there. It's just this unexplained pause at boot. Does anyone have any ideas how to fix this?

ok check it out guy's this thing drove me insane all night last night and most of today. I was ready to return everything and give up. But alas all is not lost. Here is the rundown on what i just did.
My Equipment:
Athlon 64 3800+(w/ stock fan)
MSI K8N Neo2 Platinum Socket 939
2X512 Corsair TWINX1024-3200XLPRO ( with the cool led's )
2 SATA HD (1 Maxtor Diamond10 300 GB w/ 16mb cache, 1 Segate 160GB w/8mb cache)
PP&C 425 ATX Deluxe
Radeon 9700 Pro ( cat 4.8 )
Audigy2 ZS
Sony Floppy
Sony 8x52x52x32 DVD Rewrite
I have been reading and reading just like all you guy's. On a few websites i would pick up bits and pieces on what to try. Heres what i did. Upon Boot up i entered the bios. I then went to Cell Soft and adjusted my timings for my memory. I was at 2.5 not 2.75. I then set my speed down to 166. Exited and restarted. Big mistake everything ri=uns terrible slow and my expensive DDR 400 memory was showing up correctly at 333. Rebooted again entered the bios. reset my speed to 400. Then set the Overclock feature to manual. Set my timings at 2,2,5,2 200 and 2.75 volts. After saving settings and exiting I then turned off the computer. As per some other suggestions I moved my Audigy2 to the bottom most pci slot the one above the orange slot. I moved my memory to slots 2 and 4. I moved my SATA to slots 3 and 4. I rebooted went into the bios again and setup all my voltages. CPU was Auto, AGP was max yellow setting. Memory still at 2.75. I disabled the onboard serial and parrallel ports. Rebooted
Fearing the worst,
5 seconds, 10 seconds, windows screen loging prompt. There was nothing wrong at all. It rebooted effortlessly. It re found my Audigy card and wanted driver but that was it. I am going to reboot a few more times and then run sisandra to test. I hope some of this will help you. I post in a few after some of those reboots.

K8N NEO2 PLATINUM ATA-133 Raid ?

Hello,
My question is, is it possible to setup an Ata-133 raid on the K8N NEO2 PLATINUM (as the main boot drive). Currently I have 2 ata-133 drives and I want to upgrade to this board. I looked at the PDF manual and read the forums, but people usally talk about thier Sata drives.
If it is possible to have only a Ata-133 raid setup. How/what is the best way to set it up since there is only a primary and secondary ATA connection on the motherboard. Setup a master / slave on the primary 1 slot ? or put them on thier own channel ? Note, I read somewhere that optical drives ( cdroms,...) may have a problem if they share the channel with a harddrive that is raided. So thats my dilema.
Thanks in advanced,
Jim

Quote from: crossmax03 on 02-August-05, 20:58:06
jim,
did you ever get the RAID setup to work with the IDE drives?
i was trying to connect 2 ata100 drives on the IDE2 or IDE3 ports and the bios will not seem to detect them at all,
but the RAID controller DOES detect them.
however, it will try to boot from the master drive but restarts at the windows XP splash screen, every time.
-brian
Right. If we connect two IDE HDDs on one IDE1 or IDE 2 (as Master & Slave), and plan to set up RAID.Take IDE1 for example, as long as we set up Integrated Peripherals-->Onboard Device-->RAID Config-->IDE Primary Master&Secondary RAID-->Enabled, Save&exit setup; enter RAID bios to set RAID mode, all things would be ok. But if we want to install OS in this RAID, we must press F6 install RAID driver at the beginning of OS installation. If we only use them as normal storage, OS is in other HDD, we should install RAID driver in OS.
Besides, the two HDDs could not appear in Standard CMOS Features any more, which appear in RAID BIOS.

Os/2 or beos on k8n neo2 platinum

i want to run beos on my system
or os/2
i have the k8n neo2 platinum
athlon 64 3500
1 gig geil ram
80 GB maxtor Pata hard drive
30 gb seagate Pata hard drive
60 gb SATA maxtor
ati card (wel figure that one out later)
BeOS 5 pro just reboots
and for some ungodly reason i cannot write my os/2 image files without some crap about "BAD TRACK 0" and i just bought a new pack of floppies. and it tells me this with EVERY disk
the only OTHER OS i can get to run is linux
which im quite fond of... "anything except WINDOZE"
I guess what my question is .....WHAT KIND OF VOODOO RITUAL DO I HAFTA PERFORM TO MAKE THIS WORK!!!!!!!
I dont have any chickens to bleed, but the neighbor does!!!!
Please help
ANY help would be GREATLY APPRICIATED!!!!!!!!!!!!!!!!!

Hi,
I tried to do the same with os/2 and MSI Neo4 Platinum/SLI and Athlon FX55.
OS/2 Warp 4 requires 256MB ram or less installed to do initial install. The first partition of HDD must be less than 2.06Gigs in order for the Kernel to compile.
EComStation has the newest version of OS/2. A Google search should take you right to Sundial's site.

MSI K8N Neo2 Platinum with Western Digital 750Gb Caviar Green 32mb

Hi all, this is my first post and im a bit of a numbskull when it comes to upgrading, thus this post.
My HDD is on its last legs and I want to get a Western Digital 750Gb Caviar Green 32mb. Im not sure weather it will work with my MSI K8N Neo2 Platinum (MS-7025). Can anyone help me out? If you have any suggestions for a better HDD to go for that would also be appreciated, Cheers

Burst speeds are high mainly because of the disk's cache. That's the only part of the HDD that can get near the maximum bandwdth of the controller.
The bottleneck for speed is in the fact that the HDD's mechanical properties won't allow it to work faster. With SSD's it is or will be different.
Back to topic: the WD Green is an excellent choice. I've 6 of those running here now, 5 in a NAS and 1 in my pc and they're simply good. Not the fastest, but very stable, quiet and fast enough.

Desperate: K8N Neo2 Platinum won't work!!

Bought myself a new motherboard, processor and memory and it just won't work!
Searched this forum for a solution, but haven't found one yet.
Try to install Windows XP, but it just won't start.
I now get an error code 0x80040507.
Before that, it just rebooted again and again.
My configuration:
MSI K8N Neo2 Platinum
AMD Athlon 64 3500+ Winchester core
2x512 Corsair Twinx1024-3200
Prim. master: HDD 40 Gb Seagate U100/72 ATA
Prim. slave : DVD-RW NEC ND-3500
Sec. master : HDD 160 Gb Maxtor Diamond Max Plus 9 ATA
Sec. slave : DVD-R from LG
PSU: Antec 350W, model SL350P (+5V=35A, +12V=16A, +3,3V=28A, -5V=0,5A, -12V=0,8A, +5V=2.0A)
Sapphire 9800 Atlantis Pro 128Mb
PCI-1 : empty
PCI-2 : Hauppauge WinTV PVR250
PCI-3 : Linksys wireless network card (model WMP11)
PCI-4 : Creative Soundcard SB Live 1024
Do I need a new PSU?? or is there another problem?

AMD recommends a PSU with atleast 24a on the 12v rail. This does not mean your PSU won't hack it, it just means that as a rule of thumb, it's not supposed to.
Could your PSU be the cause of your problem? Possibly! You have a lot of components drawing power from your PSU. It would be wise to buy a beefier PSU with 12v/5v/3.3v amps all in the 32+ range (see my PSU in my signature or the enermax 460/465w whisper II)).
The problem with not having a better PSU to work with is you could encounter an error, deem it as a result of something it's not, and think the PSU is good and something is bad when it's really the other way around. Moral to the story: get a new PSU.
I tried searching microsoft's knowledge base for your error and nothing turned up that had anything to do with windows installation errors. Are you sure you copied the error down correctly?
If so, the only recommendation I have for you is this. Try installing windows with minimal components installed (CPU, motherboard, videocard, single cdrom, single hard drive). Leave your SB Live! out. Leave your WinTV out. Leave your linksys card out. Leave your DVD-R from LG out. And if you are willing to conserve even more power. If you really want to conserve power, you can install windows with only one stick of ram installed.
Next thing you want to do is check to make sure the memory is not faulty. Start by putting only one stick of memory in slot one and testing it using memtest86+ (i hope that link is correct). You're going to want to run a 1-4 hour standard loop of tests followed by a 12-24 hour loop of test 5. Then you will do the same thing with stick two in slot one. After this works, test to make sure there's nothing wrong with the motherboard by doing the exact same tests again one by one with the sticks in slot two this time around. After this is all done, do the tests again with both sticks in slots one and two. if it doesn't work like this, you could have faulty memory (but this should work). You can always run your memory in the same colored slots (single channel (slots one and three)) but this will cause you to take a hit in performance. Generally, for all instensive purposes, you should be able to run it in dual channel mode without any problems. I imagine you will be able to if the sticks are good.
If they don't work in dual channel mode, to be completely honest, I don't know what you would consider the problem then... could be the PSU... could be a badly matched pair... could be the motherboard. All this is determined by how you handled the parts when installing them. There are a lot of unknowns when trying to help a user without knowing anything about their install.
If all memtests' run successfully, you are now ready to install windows. If windows doesn't install correctly, you probably have a botched BIOS setting somewhere (like aggressive memory timings) or something similiar that's stopping you from successfully installing windows.
Buy a new PSU

NOOB -MSI K8N NEO2 Platinum questions

Hi
I coming from an Intel background but am now considering changing to AMD; i'd like to keep my agp x800xt pe card and get a MSI K8N NEO2 Platinum board but have got a few questions /concerns.
I have looked on several forums including MSI's own forum and noticed people having problems with corsair value select memory modules.
My questions which i'd be grateful for answers to are:
1. Am gamer and planning to also purchase a 4000+ to put in it - will the board recognise it straight away or will I need to update BIOS..
2. Want to transfer my current 4x512mb 3200 Corsair Value Select sticks to my new board - will there be any compatibility problems? (cannot afford to buy new memory)
3. Will I be able to run the memory 200 + ? as heard the boards base clock for a 4000+ is 166
4. If I can run these at 200 can i do this straight away or will i need to overclock them slowly to get to 200 (will the board see them as 3200 and start at 200?)
5. Anything else I should know/look out for?
Many thanks to all. My first post here so hello to everyone.

Hello !!
Let´s try to answer your questions...
1. It depends on which Bios Version is installed out of the Box, i suggest version 1.8, if you are not using a Venice / Dual-Core or later CPU Core. The advantages of biosses later than version 1.8 are the new Steppings Support and some new Memory Timing Options available in Bios Setup.
2. I do not know exactly, i think most corsair sticks are running well on this Board if you are not going to overclock. But it depends on which Chips are used your Corsair Modules. What could be a problem is that you are going to use 4 Ram Sticks, because with Winchester Cores you would not be able to run 4 Sticks in PC3200Dual Channel Mode (DDR333), even if your Ram would be 100% compatible with your MOBO. Venice and later Cores are able to handle 4 sticks at 400Mhz DDR clock. Except you own 4 single sided Ram Modules.
3. Should be possible if your memory likes it.....
4. No, the Bios will recognize your SPD Timings. So you will have to overclock them from a 166Mhz Memory Divider Base.
5. Take a look here:
http://xtremesystems.org/forums/showthread.php?t=46730
https://forum-en.msi.com/index.php?topic=72024.0
http://www.msi.com.tw/html/products/mainboard/testreport_pdf/7025/memory.pdf
Good Luck
Greetz MurdoK

K8N Neo2 Platinum 2 DIMMs won't post

I have two 512 MB Crucial DIMMs (DDR PC3200, CL=3, UNBUFFERED, NON-ECC, DDR400, 2.6V, 64Meg x 64, Part #CT6464Z40B). If I have either one installed, the system will POST. If I have both installed (I've tried them in both recommended combinations, in DIMM1 and 2 and in DIMM3 and 4), the system won't POST. The D-Bracket displays the Memory Detection Test signal. Since each stick works alone, I don't think either one is faulty. Can anyone explain why this is happening, and how to fix it?
Specs:
MSI K8N Neo2 Platinum
AMD 3500+ 939
eVGA e-GeForce6800 128MB DDR AGP 8x
Antec 380S PSU, 380W.

im having the same problem. same ram, same motherboard. except when i put the ram in slots 1 and 3 the computer will start up, but it will freeze in windows everytime. what should i do? i want to use all of my ram now only one stick!!!!!!!!!
and i have updated bios to 1.4 and it still doesnt work

MSi K8N NEO2 Platinum

Hello to everybody
just one quik question does the the Thetmaltake Tower 112 (the 100% copper made) fits the msi K8N NEO2 platinum???
i search on the net but i wasnt able to find something relevant
thenks
p.s. please post if you now for sure i don't wanna answers like it should fit..please thenks again

If it is made for a K8 then it will likely fit. However you may want to check into that things weight as most of those huge copper coolers go over the weight limit the board can support. That can lead to cracked or broken parts at some point. All that for just a couple degrees in cooling is a bad idea. If you feel you really must have better than stock cooling maybe the better thing to look at would be a watter cooling system.
Oh ya you may want to try the search button here too... {sarcasm mode off]

New K8N Neo2 Platinum, AMD 64 3500+ sytem freezing

I have posted to a couple of forums and still can't get this problem resolved, hope you guys can help.
I put together a new system last Friday night and spent all weekend trying to fix it. I ended up with 2 bad power supplies, one fresh from the store was dead, but got that resolved. Got the system up and running, got online, surfing and FREEZE..everything stopped. Rebooted, 5 minutes later, same thing, over and over again.
Tried checking memory, it's fine, both sticks, power supply is fine, everything seems to be running fine except it keeps freezing after about 5 minutes.
I wonder if it's a bad board, so I tried to RMA it with the vendor and they want me to try outside the case to see if it won't freeze there, haven't had the time yet cause I'm working, will try that tonight.
Also, one guy on a different board suggested that I try a fresh install of windows xp as the old drivers might be interfering with the new drivers. I will try that tonight also.
If anyone can give me any other suggestions, I would appreciate it. If I can't get this resolved, I'm going to send back the board for a new one.
Below are my specs:
AMD 64 3500+
MSI K8N Neo2 Platinum mobo
2 x 512 Kingston ddr400 (pc3200)
antec true power 480
wd 120gb hd, wd 80gb hd
cdrw generic, dvdrw generic
bfg 6800 oc video card
thanks

Thank you both for your posts, they are both informative and I will be using your information Friday night. I'm just so tired after work, I don't want to get part way into it and have to leave it for the next day, I have to get up at 3am everyday and get home around 6-7pm and I'm beat!
So, Friday after work, I'm going to start with just the basics and go from there, using all the information I've been getting from this board and a couple of others. Seems like the best thing to do is, start with barebones, reset cmos, reset battery and install fresh windows os.
I will post Friday after I start and hopfully I will get this problem fixed.
thanks again

BIOS for K8N Neo2 Platinum

Hi to all.
Just wanted to know what's the best and most stable bios for my K8N Neo2 Platinum. I'm currently running ver. 1.B, but I've read that ver. 1.9 is the best. Just wanted to know everyone's thought on this one.
In case ver. 1.8 is better,
¿can I flash my bios to ver. 1.9 from 1.B without having any problems?
¿Is ver. 1.9 better for overclocking?
Thanks.

Quote from: Stu on 20-May-06, 07:55:41
if you wanna OC, then Syar's BIOS is the best bet; its the one i use
I agreed with you Stu as I'm also using Syar's Bios 1C.

Want comments on k8n neo2 platinum prior to buying it,

Similar Messages

Maybe you are looking for