Want DELL PC to network with Mac Airport Express

I installed Airport Express in my PowerBook - works fine for me - but my husband's Dell gets kicked off really often. And I can print wirelessly, but can't get his Dell to print. Anyone understand the compatibility issues?

I installed Airport Express in my PowerBook - works
fine for me - but my husband's Dell gets kicked off
really often.
Ensure that the Enable IEEE 802.1x authentication for this network check box is not checked.
Problems connecting an XP PC to an Airport Base Station
http://tech.ifelix.net/2002.html
And I can print wirelessly, but can't
get his Dell to print.
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express
http://tech.ifelix.net/1004.html
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express using Bonjour
http://tech.ifelix.net/1008.html
Problems with finding Printer Driver on Windows XP when using printer connected to Airport Extreme or Express
http://tech.ifelix.net/1012.html

Similar Messages

  • I am unable to join my existing wireless network with new AirPort Express

    I am unable to join my existing wireless network with new AirPort Express.
    I am using a DLink DI-524 Router, Windows 7 (64), and the AirPort Express.
    AirPort Utility will not recognize the AEX wirelessly, it will only recognize it when it is connected by Ethernet. I can then configure the AEX and verify that the settings stick once disconnected and then reconnected. However, even after that, it will not recognize the AEX once disconnected from the Ethernet cable.
    I followed the suggestions of several other threads on these forums. But I am unable to get the AEX to work.
    Any suggestions? Thanks in advance.

    Welcome to the discussion area!
    It's almost always a security setting that causes problems when the Airport Express (AX) tries to join a third party wireless network. The AX usually does not "join" correctly and that's why you can't see it on your wireless network using AirPort Utility.
    Using an ethernet cable is still the more reliable way to configure and adjust the AX, but if you are want to try to configure it using wireless, you must return the AX back to factory defaults as follows:
    Power down the AX
    Hold in the reset button +and keep holding it in+ as you plug the AX back in to power
    Release the reset button after 10 seconds
    When it is set to factory defaults, the AX broadcasts a wireless signal with a network name like "apple network xxxxxx" where the "x's" are either letters or numbers. You must look for this network by clicking on the fan shaped Airport icon at the top of the screen. If you don't see this network, then click Join Other Network to search that way. Unless you connect to this network, you will not be able to configure the AX using wireless.
    Do you know the exact security type that your D-Link router is using? That is the key element in the process.
    Open AirPort utility, click Manual Setup
    Click the Base Station tab to establish a name for the AX, device password and adjust time zone settings
    Click the Wireless tab
    Wireless Mode....Join a wireless network
    Wireless Network Name...must exactly match your D-Link wireless network name
    Enable ethernet clients if you want the port to be active (your D-Link must be compatible with ProxySTA for this to work)
    Wireless Security...exact setting of the D-Link network. WEP security causes a lot of issues. Try to use WPA/WPA2 Personal, which is far more secure.
    Wireless Password...must match the D-Link network
    Click the Music icon to enable AirTunes
    Click Update to save settings
    Any luck?

  • Trying to extend my airport extreme network with an airport express

    I´m trying to extent my network with an airport express 802.11g.
    I´ve been fallowing the guide:
    http://support.apple.com/kb/HT4259
    however, when I´m trying to configure the extended wifi base station ( point 8.)  it won´t let me choose "extend a wireless network".
    The only options I have is "create network", "join network" and "participate in a wds network".
    I´ve been trying to find a solution all day.
    Is there anyone out there who has hade the same problem or knows what it could be?
    I´ve made sure that my base station connected to the internet through ethernet has checked the "allow this network to be extended"

    however, when I´m trying to configure the extended wifi base station ( point 8.)  it won´t let me choose "extend a wireless network"
    Unfortunately, the older AirPort Express 802.11"g" model does not have a setting to "extend a wireless network", so it cannot be used the way that you want.
    The article that you reference should be clear about this:
    This article explains how to set up an 802.11"n" extended wireless network.
    You need to use one of the newer AirPort Express 802.11"n" models to gain the ability to "extend a wireless network".

  • Unable to create a wireless network with my airport express.  Please help!

    I am trying to setup a wireless network with an airport express, and connect to it with my Macbook. I just bought both of these and haven't been able to get wireless to work.
    I initially plugged the ethernet cable from my cable modem into the airport express and plugged it into the wall. The macbook detected it when I opened airport utility, but the express had a flashing amber light and I was unable to connect. I then unplugged the express and re-started the cable modem. This time, the airport express showed a solid green light -which should mean that it is working correctly. However, the macbook did not find the airport express device when i searched for it using airport utility. I am able to connect the macbook directly to the cable modem, after re-starting the modem, and access the internet so at least some of the systems are go.
    Any ideas? Thanks in advance for your help.
    Tom

    Is the issue that you cannot access the 802.11n AirPort Express Base Station (AXn) with the AirPort Utility that is running on your Win7 PC? ...  or that once you have configured the AXn, the PC is unable either to find the new wireless network or can find it but cannot connect to it?

  • Trouble extending my WiFi network with older Airport Express

    Hi,
    As the question states, I have an older Airport Express which I have dug out to try and extend my WiFi network in a new house.
    I am on Virgin Media (fibre optic) in the UK and get a good WiFi service but one room in the house (which I have just turned into a cinema/media suite) has no reception.
    I have successfully managed to 'create a new network' via the Airport Express and the signal strength is 100% but for some reason if I try to reconfigure the device to extend the existing network I get no improvement at all from the (zero) signal I was receiving before.
    Am I doing something wrong? Or is there an additional step I am missing?
    I could live with having a secondary network but what I would really like to achieve is Home Sharing from my main computer, so that I can access my photos, movies and music etc. from iTunes on the big screen. If the computer exists on another network my iPad, iPhone and AppleTV can't see/use the media from that room.
    Many thanks in advance,
    Colin

    Are these the steps you used?
    To create a wireless extended network, you must place any extended Wi-Fi base stations within range of the primary Wi-Fi base station.
    Start with the device that will be configured as the primary Wi-Fi base station.  Then configure your extended Wi-Fi base stations, ensuring that each is within direct range of the primary Wi-Fi base station.The physical location of extended Wi-Fi base stations will vary according to the building environment and may require some experimentation.
    If you have configured your Wi-Fi base stations in the past, it may be helpful to do a factory default reset of each Wi-Fi base station that will be part of the wireless extended network before you begin.
    Configuring the primary Wi-Fi base station
    Power on all 802.11n Wi-Fi base stations and allow them time to appear in the AirPort Menu Extra.
    Open AirPort Utility (On a Mac, choose Go > Applications from your  desktop, click the Utilities folder, then open AirPort Utility. In  Microsoft Windows, choose Start > All Programs > AirPort to start  AirPort Utility).
    Select the primary Wi-Fi base station in the Base Station Chooser, then click Continue. Note: If you see a message appear that indicates that the Wi-Fi base station has been reset, click Cancel to continue.
    Click Manual Setup. Enter the base station password if necessary.
    Click AirPort in the toolbar.
    Click Wireless.
    Choose “Create a wireless network” from the Wireless Mode menu.
    Select the “Allow this network to be extended” checkbox.
    Enter a Wireless Network Name.
    Optional: By default, Wireless Security is set to None so that no password will be required to join the network. We recommend you click on the Wireless Security menu,  select WPA2 Personal, and create a password between 8 and 63 characters long.
    From the Radio Channel Selection menu, select Automatic.
    Click Update.
    The next window may indicate that there are some problems. Resolve the problems, then click Update.
    You are now ready to add extended Wi-Fi base stations to your network.
    Configuring an extended Wi-Fi base station
    Place any extended Wi-Fi base stations within range of the primary Wi-Fi base station
    Ensure that all 802.11n Wi-Fi base stations are powered on and allow them time to appear in the AirPort Menu Extra
    Open AirPort Utility (On a Mac, choose Go > Applications from your  desktop, click the Utilities folder, then open AirPort Utility. In  Microsoft Windows, choose Start > All Programs > AirPort to start  AirPort Utility).
    Select the Extended Wi-Fi base station in the Base Station Chooser, then click Continue. Note: If you see a message appear that indicates that the Wi-Fi base station has been reset, click Cancel to continue.
    Click Manual Setup. Enter the base station password if necessary.
    Click AirPort in the toolbar.
    Click Wireless.
    Choose “Extend a wireless network” from the Wireless Mode menu.
    Choose the network you want to extend from the Network Name menu.
    Enter the network and device password if necessary, then click Update.
    The next window may indicate that there are some problems. Resolve the problems, then click Update.

  • Networking with Multiple Airport Express'

    I am using a new Airport Extreme 802.11n as a router in a home network that is in an extremely large house. I also have 3 new Airport Express' connected to the network. My question is should the settings in the Airport Utility be "Join an existing network" or 'Extend an existing network' for each Airport Express' or some combination of either based on which express is first in closest proximity to the Airport Extreme.
    Thanks, JB

    I've only got the two running now, and the signal at the far end is dramatically better than without.
    I don't think it decreases bandwidth for each device. Each machine's bandwidth decreases a little for the overhead, but it is not cumulative.
    On a side note, when I added the New Airport Express, I had an absolutely horrible time getting it all to work correctly and I think I had similar symptoms as you are describing. I was able to differentiate which base station I had connected with because the new Airport Extreme was n-band and the main stations is an old g-band. So, by holding down the option key when selecting the airport menu, I could easily see the bandwidth going above 54. I hope you're laughing as I later realized that the MAC address of the base station you are connected to shows up in the menu with option held down, also.
    Everything seemed to be connected right, but it just wasn't working. I ended up resetting both devices and started from scratch. Just about when I was going to give up and just extend the network, my WDS connections worked and I haven't had any problems.
    Before I realized that the network wasn't configured correctly, I thought my old Airport Extreme was going bad. It was freezing up and I had to restart it to get an internet connection. Ever since I fixed the WDS network, I don't have any problems with it. I think the two base stations were jamming each other.

  • Creating and Extended Network with 2 Airport Express Units

    I had an extended network using 2 express units but one of them broke. The old network was setup with an older version of Airport Utility and I can't seem to repeat the set up a new network with the new express unit I have bought.
    The simple setup procedure using Airport Utility 5.5.1 only appears to allow you to 'join' the remote Express unit to an existing network, there is no 'extend remotely' option.
    I remember doing it last time by creating a WDS network which agrees with instructions I have found here - http://broadcast.oreilly.com/2009/03/taming-an-airport-express-wds.html
    I set up the first Express as a base station with a network and select 'Participate in a WDS network' and 'Allow this network to be extended' under the wireless tab. Under the WDS tab I 'Allow wireless clients' and add the hardware address of the second express unit.
    I then update the express unit but I get a WDS error which states, "This Airport wireless device is set up as part of a WDS network but no other AirPort wireless devices were found."
    This seems to be a chicken and egg situation.
    Any help would be appreciated.
    Alan

    Alan, welcome to the discussions!
    It appears that you want to set up a WDS arrangment, correct?
    But, I can't figure out whether you want to configure it with a "base" and two "remotes", or whether you want to configure it with a "base", "relay" and "remote"
    Can you clarify? I'll send you a link with instructions from forum expert user Tesserax with step by step instructions. Just need to know what set of instructions to send.

  • How do i extend my network with a airport express

    How do I extend my network with mt airport express

    Hi Tesserax, I'd like to join this discussion. It seems Jasonbeyer didn't reply, but I have a question related to his.
    I'd like to extend the wireless signal from my Cisco Model DPC/EPC2202 VoIP Cable Modem (802.11n) to the living room where, at the moment, it is non-existent. I assume there's inteference or the signal cannot reach through the concrete walls and rooms leading up from my bedroom to the living room.
    My question is:
    I'm thinking of extending my wi-fi signal by using the Airport Express and simultaneously using it to connect to my hi-fi to play iTunes from my bedroom's iMac.
    Something's telling me it's not going to be that easy. I'm using an iMac (7,1) if that's any help or clue.
    What are the things I should take note of and will Airport Express be compatible with my modem? Would I have to get TWO Aiport Express to bridge the signal to my living room?
    Thank you everyone for your time. Cheers!
    Kane

  • Extending My network with three Airport Express or buy an Airport Extreme?

    I live in a large three story house and currently have it wirelessly networked using two Airport Express' but my signal is very weak on the third floor and in other spots throughout the house.
    Would it be possible to buy a third AE and extend the network that way or would I be better off buying a AEBS?
    Any thoughts or suggestions would be greatly appreciated.
    Thanks

    It will really depend on the construction materials used in your house or any other forms of Wi-Fi interference that could prevent a clear wireless signal. Both routes, you suggested, will have it advantages and disadvantages.
    Extending the existing network wirelessly using a WDS, effectively, cuts the throughput in half for each base station in the chain...so, in this case the second AirPort Express Base Station (AX) (acting as a WDS relay base station) would only get half that of the first AX (acting as the WDS main base station). In turn, the third AX (acting as the WDS remote base station) would receive half of the second's throughput. The good news is that you should have a strong signal across each of the AXs, just lower throughput the farther along in the chain.
    The 802.11n AirPort Extreme Base Station (AEBSn) has a greater range than either the older 802.11g version or the AXs. You may find that it will provide enough to cover you entire house. In the off-chance that it doesn't, you can still use it to create a WDS between AEBSn and your current AXs.

  • Extended network with 2 Airport Expresses, Mac connects to the far away one

    I have two Airport Express 802.11n units that are set up as an extended wireless network. This is not done using WDS, but instead using the "Extend wireless network" option on the 2nd Express. I do this to get extended coverage in my apartment.
    Most of the time this works flawlessly. However, sometimes my Mac connects to the wrong Express (e.g. the one that's further away). I notice this because I don't have full bars on my Mac's wifi icon. When I go into the Airport Utility, choose the far away Express, go to the Advanced tab and click "Logs and statistics", I can confirm that my Mac is in fact connected to the far away Express.
    If I disconnect and reconnect my Mac from the network, it will most likely then connect the closer Express and my signal will vastly improve. I can confirm that it is connected to the right Express using the Airport Utility.
    Does anyone know why this happens, and is there a way to force my Mac to connect to the closer Express?
    Message was edited by: nonnynz

    Hello nonnynz. Welcome to the Apple Discussions!
    Does anyone know why this happens, and is there a way to force my Mac to connect to the closer Express?
    It would be quite logical to assume that the algorithms Apple employs to connect to a wireless router would connect your Mac to the closest (or one with the strongest signal) but it doesn't always work out that way. Furthermore, Apple hasn't released the specifics on how this algorithm is supposed to work so it may be a bit difficult to answer your question with any facts to support it.
    ... and no, as far as I know, there isn't a sure-fire way to force your Mac to pick the desired base station. Something that comes to mind is to change the Multicast Rate, under Wireless Options in the AirPort Utility, to a higher value for the base station that you don't want your Mac to connect to first ... but this may only be of value if you keep your Mac near the other station and would cause the opposite effect when you move to the one you just adjusted.

  • Cannot create a WDS network with two Airport Express

    so i have one airport express here at my parents house acting as a wireless router. i brought a second express from my house and my playstation3 and want to connect the ps3 via Ethernet, i reset my express from home by holding the small pin-sized button. i open up airport utility choose the default named airport express, hit continue>switch>name it and give it a password>I want it to join my current network>Extend the Range of my Network>Chose my network (Twice)>watch the 'configure' WDS screen. then i get this:
    http://farm4.static.flickr.com/3632/3420465586a2f1864300o.png
    both expresses have been recently updated with 6.3 firmware and i'm accessing both wirelessly. i've tried over and over again resulting in the above image, can anyone please help?
    btw there is no 'allow this network to be extended' box.

    Psych,
    Do the setup hard wired to your Mac - so connect an ethernet cable between your Mac and the AX you're trying to set up. Do the setup as usual, and once the configuration has written to the AX, restarted and you have a green light, you can remove the cable and connect wirelessly.
    Sometimes, and for some reason, the configuration has problems writing to the AX wirelessly, especially after a reset.

  • Extending an Airport Extreme (6th Gen) network with older Airport Express models

    I just purchased the latest Airport Extreme (6th Gen) base station to be my main wifi router.  I have two airport express models that I used in the past to extend my network with my (very) old retired Airport Extreme (2nd Gen): the 2nd Gen model A1264 (you plug into the wall directly) - I've had it for several years, and the newest 3rd Gen model A1362 (small square that lies on a desk or table) - I just purchaed a couple of months ago.
    My question is - will extending my network with either of these Airport Express models diminish my overall network speed (Especially the older model)? 
    I don't have any AC capable clients yet - so everything is running on the "n" band - and the older Express is an "n" model, but I just have this (perhaps irrational) fear that attaching older routers will slow everything down.
    Any thoughts or suggestions?
    Thanks!

    will extending my network with either of these Airport Express models diminish my overall network speed (Especially the older model)?
    The A1264 model will be able to extend only one band of the new dual band AirPort Extreme. Normally, the A1264 will extend the 2.4 GHz band since it is stronger than the 5 GHz signal.
    The A1392 will be able to extend both bands since it is also a dual band model, providing that it is located where it can receive a strong wireless signal from the new AirPort Extreme.
    Here, I am assuming that you are asking about extending wirelessly.
    You might want to keep in mind that extending wirelessly always involves compromises and loss of bandwidth. The main reason for this is that an extending device can only "extend" the quality of signal that it receives.
    The wireless signal from the new AirPort Exterme will slow down and lose strength the further that it moves away from the main AirPort. So, the extending device gets a slower, weaker signal to extend. The result is signficantly slower wireless performance in the extended areas.
    The way to solve this is connect the extending AirPorts to the main AirPort using a permanent wired Ethernet connection.  There is no signal loss in a wire, so the extending AirPort receives a full bandwidth signal to broadcast. The result is higher and more uniform speed on the entire network.

  • Extending airport express wireless network with another airport express

    I am trying to set up another airport express to my existing airport express at home so I can extend the wireless range and also to connect my printer (to my second airport express) so I can have a shared wireless printer. Is this possible? If so, can someone assist me on how to set this up?
    Thanks.

    Try the following ...
    AirPort Express Base Station (AX) - WDS Setup
    "Factory Reset" the AX base stations
    o (ref: http://docs.info.apple.com/article.html?artnum=108044)
    (Note: To facilitate setting up the base stations, place them in near proximity of each other during the setup phase. Also record the Apple IDs of each base station that will included in the WDS as these will be required during setup.)
    Main Base Station Setup
    (Note: The AX connected to the Internet will be assumed to be the main base station in the WDS.)
    Either connect to the AX's wireless network or by temporarily connecting directly, using an Ethernet cable, to the Ethernet port of the AX, and then use the AirPort Admin Utility to make the following settings.
    WDS Tab
    1. Enable this base station as a WDS: main base station (checked)
    2. Allow wireless clients on this base station (checked)
    3. Click "+" to add Remote/Relay Base Stations.
    3a. Select the Base Station that you want to be the WDS Remote/Relay.
    3b. AirPort ID: <verify that this is the correct MAC address for the Base Station you are adding as a Remote/Relay.>
    3c. Auto configure as a WDS remote base station (checked)
    3d. Click "OK."
    4. Verify that the Remote/Relay Base Station has been added to the list.
    5. Click "Update," and then verify the settings for the Remote/Relay.
    5a. Allow wireless clients on this base station (checked)
    5b. New network name: <verify that this is the same as the network name as the main base station>
    5c. TCP/IP: Configure using DHCP
    5d. Base Station Password: <the Remote/Relay Base Station password>
    5e. Confirm: <same as previous step>
    5f. Click "OK."

  • AirPort Basis Staion with BroadBand and Network with 2  Airport Express

    Strange Phenomena
    We can log into Internet through the Base Station without any problem and connect to more than one Mac. But the moment we set up a bridge between the BS and the AP Expr. we can only either connect to the InterNet or use it as a network but not both. It worked for months fine but now neither of the AP Expr will do both. We have tried another BS to no avail. Does anybody no this problem is it maybe after a System Update? Our customer is getting mad as he cannot get it to work He had the BS steup and both Express's setup to be Bridges (WDS) and all worked then suddenly from one day to the next no more.It doesn't matter how you configure the Express it will tell you that it cannot start a remote connection to the BS. All very Strange

    Hello macfar14. Welcome to the Apple Discussions!
    For just streaming iTunes and/or for sharing a USB printer, the AirPort Express Base Station (AX) just needs to be configured as a wireless client ... which you already attempted to do.
    Just to be sure nothing was missed, here are the basic steps to do this:
    Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
    AirPort > Wireless
    o Wireless Mode: Join a wireless network
    o Network Name: <existing wireless network's Network Name or SSID>
    o Wireless Security: <select the encryption type of the existing wireless network>
    o Wireless Password: <enter the existing wireless network password>
    o Verify Password: <re-enter the existing wireless network password>
    Music
    o Enable AirTunes (checked)
    o iTunes Speaker Name: <enter desired speaker name>
    o iTunes Speaker Password: (optional)
    o Verify Password: (optional)
    o Click Update to write the new settings to the AX
    In iTunes:
    iTunes > Preferences... > Advanced > General
    o Look for remote speakers connected with AirTunes (checked)

  • Ist it possible to extend a wifi network with sevral Airport Express's?

    Hi, I live in a house with 3 floors. My router and my timecapsule are located on the 2nd floor and I want to extend my network wirelessly to the first floor and the ground floor by adding several (2) Airport Express stations to my network. Is this possible?
    Basically like on the picture linked:
    https://www.dropbox.com/sh/g8mvrbgo4r38lzr/5uCsbQ5E2w?v=1mci
    Somehow it works brilliant but, once I add the second AE my MacBook won't sign into the second AE but will stay in the first. Resulting in just not extending my network.
    Thanks

    Somehow it works brilliant but, once I add the second AE my MacBook won't sign into the second AE but will stay in the first. Resulting in just not extending my network.
    That's because you can only wirelessly "extend" the network one time, not two.
    Apple's "extend" setup works like the hub and spokes of a wheel. The Time Capsule would be your hub. There can be multiple AirPort Express devices, but each Express resides at the end of a separate spoke...and it communicates directly to the hub....not to another device at the end of another spoke.
    The second extender is "joining" the network, but it provides no additional wireless signal coverage when it "joins".
    You will need to move the second AirPort Express closer to the Time Capsule.....to the point where the display indicates that both Express devices are connected to the Time Capsule.
    Another approach might be to move the Time Capsule to the central area on the 1st floor, then locate an AirPort Express above and below that area. That would work.
    If that is not possible, then you will need to think about a wired Ethernet connection from the AirPort Extreme to the location of the second AirPort Express.

Maybe you are looking for