Want to build an auto charging and discharging system with DAQ

Hi. I'm a freshman here. Now I have the DAQ-6009 and a labview software and some electronic elements. I wish to build a lithium ion battery cycles testing system (mainly for auto-switching) in order to observe the changes in the electrode. How can I build this charging and discharging system? The details of the battery are attached. Thank you!!
Attachments:
sanyo ml414 charging detaiils.pdf ‏75 KB

Hi freshman,
your spec sheet already mentions some resistors for loading and discharging your Li cell.
- With your USB6009 you can drive some transistors to switch between charging and discharging. You also have some AIs (analog inputs) to measure Li cell voltage as well as currents (when using some reasonable shunt resistors).
- Make an electronics sketch, read the manual of your USB6009 for it's specs and then grab your breadboard to build your electronics.
- Look at the examples coming with LabVIEW on how to switch DO signals and how to measure voltages (read the manual on that topics too!)
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Similar Messages

  • Can I unlock my Droid Charge and use it with a sim card in India?

    How can I unlock my Droid Charge and use it with a sim card in India?

    You just have to call VZW Global TS and as long as you meet all of the requirments you will be able to unlock your phone.
    Must be a Verizon Wireless customer.
    The device being unlocked must be active on a VZW line of service.
    The line of service must be active for at least 60 days.
    For converted accounts from acquisitions or mergers (i.e. Alltel, Unicel/RCC, etc.), the line of service must be active in the VZW billing system for 60 days from the conversion date.
      The line of service must be in good standing for the past 60 days.  Good Standing is defined as:
    Balance must be current 
    No service suspensions or hotlines in the past 60 days.
    Customer may only have one 3G SIM unlock per line every 10 months.
    The customer's manufacturer's device warranty is not affected by a 3G SIM unlock as long as the customer remains with VZW.

  • Using old charger and USB cable with new 755

    Just purchased a 755p from Verizon.  I've used a Tungsten E2 for a long time and was wondering if I can use my old charger and USB cable with the 755p.
    Post relates to: Treo 755p (Verizon)

    They are compatible.
    Post relates to: Palm TX

  • HT1476 i plug in my phone to the  charger and i tried with two different cables, and it seems like it is not making connection to the clable?

    i plug in my phone to the  charger and i tried with two different cables, and it seems like it is not making connection to the clable. but it is not charging. what are some possible ways o fix that?

    When you plug in your charger and attach it to the MBP, initially the light will turn green.  If the MBP needs charging, a few seconds later the light will turn amber.  That is normal.  If your symptoms are different, then they may or may not be a problem.
    Ciao.

  • Archive / Delete in AE and Application System with Local IE

    Hi:
    When come to archive and deleting strategies, except the messages persisted in central Integation Engine, should we include messages in Adatper Engine and Local Integration Engine ?
    Thanks
    Liang

    if you are busing windows server backup they should self manage the space, the exception would be if you are using the external drive for something else besides the backups and that is causing it to run out of space.
    Your external device should have a "windowsimagebackup" folder that contains the backup since you have not been getting a backup in the past 3-4 night you may want to just wipe that folder and start fresh with a full backup. the drive space may be misleading
    too, if the drives you are backing up don't have enough space to create a snapshot you will get space errors so you may want to make sure you have space available on the backup drives too.
    If your exchange component on SBS has not backed up you may have accumulated transaction log files causing disk space to be too low. you can clear the log files but turning on circular logging cycle the unmounts exchange database and remount, then turn off
    circular logging and cycle the database again. Circular logging can be found under the database setting in the exchange console.

  • Just moved to new home, updated router and new system with Time Warner and now we cannot get the appl

    just moved to new home, updated router and new system with Time Warner and now we cannot get the apple any ideas?

    Castle15 wrote:
    just moved to new home, updated router and new system with Time Warner and now we cannot get the apple any ideas?
    Cannot get the Apple.. what?
    Model and actual device you are talking about?
    Apple covers a pretty huge range.. If you mean extreme.. did you reset it to factory and start over.. that is always necessary when you change a network. You cannot pick up a router from one home and network and plonk it into another and have it work.. aint gonna happen.
    You also need to power down any pure cable modem for 20min or so to get it to forget the old MAC address that captured the IP so the Apple ??? has a chance to work.

  • Battery BL5C charges and discharges very quickly

    Hi,
    I am using Nokia 1650, Battery BL5C. This battery fully charges in less than 1 hour(the messgae saying battery fully charged pops-up). And this, so-called fully charged battery discharges very quickly, in a days time and mobile gets switched off. Mobile is used only for making and receiving calls which are very few and also i usually do not use it for playing games on it. (Point is, its not so heavily used to discharge the battery so quickly.)
    Is this battery problem or phone's hardware/software problem? I heard its happening to quite a many cell phones.
    The mobile phone I used earlier also had this problem.
    Thanks.

    Try to calibrate it.
    1. Run the battery empty.
    2. Charge it without turning the phone on.
    3. Once battery full, turn it on, and try to charge again until you get the full warning.
    4. Let the battery run till dry again
    5.Charge without turning the phone on
    6. Boot then charge to full
    Battery should be calibrated by then,.
    If you find my post helpful please click the green star on the left under the avatar. Thanks.

  • Can Itouch be charged and fully functional with Pioneer AVIC-Z3 auto stereo

    I am considering getting the Pioneer AVIC-Z3 navigation/stereo Head in my car. I am told that the Pioneer unit will not charge an Itouch that has higher than version 1.15 because of charging voltages/pin changes. I was also told that a Scosche Passport will not solve this problem with the Pioneer systems.
    1- Pioneer reps told me that if my Itouch has version 1.15 it will charge and have full functionality with the Pioneer Z3 as that was when the Z3 was designed for. My Itouch has version 2.2 I believe. Can I "downdate" to version 1.15 and how?
    Anyone have any experience and advice with this matter. This may be a deal breaker.
    Thank you.
    Don

    Pioneer reps told me that if my Itouch has version 1.15
    It's NOT the software version you are running that counts! First generation touches support both FireWire and USB charging; Second generation touches charge only with USB.
    The allowable FireWire voltage range is something like 8 volts to 36 volts so auto charger manufactures didn't have to do anything to use the 12 volts a car has.
    Second generation touch charging support requires the manufacturers add a regulated power supply to furnish the USB 5.0 volts.

  • Griffin PowerJolt 12V Auto Charger AND Whine/static

    Hi,
    Just got a new car that lets me use a line in to run IPOD through stereo. This works great! When I try to play IPOD and charge at same time, I hear a whine noice in the car speakers. When I unplug the Griffin auto charger, it goes away. I don't even know if I can play IPOD while it charges? If I can, then is there something wrong with my charger?
    Thanks!

    the charger isn't properly shielded.

  • Battery of 5800 charges and discharges very quickl...

    Since a few months I have to recharge my 5800 1-2 times a day and the recharge takes only one hour instead of the usual 4 hours.
    I replaced the battery (BL-5J) twice with an original Nokia one but a new battery has the same problem.
    It seems that the formware after V30 interprets  too early that the battery is fully charged.
    I took out the battery and measured the voltage (without load) of the battery:
    After the phone says 'Charging complete' : 4.0 V
    After the 'Battery low' popup on the phone 3.4 V
    Nomially it is rated  3.7 V and at beginning of charging the ammeter shows 800mA, so 1.3 Ah takes at least two hours to charge with constant current and even more with constant voltage.
    What can be the problem here ?
    When that is the case

    Try to calibrate it.
    1. Run the battery empty.
    2. Charge it without turning the phone on.
    3. Once battery full, turn it on, and try to charge again until you get the full warning.
    4. Let the battery run till dry again
    5.Charge without turning the phone on
    6. Boot then charge to full
    Battery should be calibrated by then,.
    If you find my post helpful please click the green star on the left under the avatar. Thanks.

  • Does auto-save and version work with old apps like pages '09?

    Hello,
    I'm new Lion user. I tried auto-save and version with textedit and it works.
    But i'm not sure it works with pages '09.

    It does work if you install the update from yesterday.

  • Integrating MDMP and Unicode systems with IDoc interfaces

    Hi,
    We are working on integrating SAP R/3 6.20 (MDMP) with SAP PI 7.0  SP10 (Unicode) system.  The source will send MATMAS or CLFMAS IDocs with Thai / Japanese characters and PI should transform and post it to SAP ECC 5.0 Target system [IDoc to IDoc scenario].
    ( SAP R/3 Legacy 620 - Non-Unicode / MDMP ) |---->  ( XI  - Unicode) ->  (ECC - Unicode)
    Had a look at few SAP notes (745030 ,656350 and 613389)  and it looks like there is no standard way/best practice to handle this scenario. 
    References:
    1.PDF of TECHED Session ID: IM101 Dealing with Multi-Language Garbage?Data – Lessons Learned
    2.SAP Note 745030 - MDMP - Unicode Interface_Solution Overview.pdf
    3.MDMP_Unicode_Transfer_final.doc from SAP Note 745030
    4.SAP Note 656350 - Master Data Transfer UNICODE to MDMP Systems with ALE.pdf
    5.SAP Note 613389 - ALE SAP system group with Unicode systems (Solution-2)
    My understanding per SAP Notes: (Please correct me if I'm wrong)
    a. For MDMP integraton we can't use Standard ALE Config instead we have to use Custom Configuration (IDoc collection setting in Partner profile &Scheduling  RSEOUT002/RSEOUT00_MDMP and use Function module :IDOC_INBOUND_ASYNCHRONOUS_2 ).
    b. The RFC Destinations should use proper logon langauage for correct MDMP IDoc transfer (For sending IDocs with Japanese character, the logon language should be JP).
    c. If we want to transfer IDocs in more than one language we need to create multiple Partner profiles/RFC destinations each with specific logon language.
    Please guide us in integrating these systems if you have done a similar integrations, following are my questions:
    1] Is there any configuration change required at PI layer?
    2] Do we need to install codepages in PI Unicode system for all languages used or Unicode system is capable of handling all the languages?
    3] Is it necessary to install any SAP Add-on package in R/3 MDMP system inorder to support MDMP to Unicode data transfer?
    3] If we want to send MATMAS/CLFMAS IDoc with Thai/Japanese characters from same system, what are the changes required at the Source system?
        (Source may send MATMAS/CLFMAS IDoc with either Thai/Japanese characters but not both of them in a single IDoc)
    4] Can we use regualr ALE & Partner profile settings for handling multi-byte characters or we need to use IDoc collection and RSEOUT002/RSEOUT00_MDMP report for transfer?
    5] Is there any restrictions on the IDoc types (MATMAS,CLFMAS etc) supported in MDMP-Unicode integration solution.
    5] Is there any best practice document available for this scenario?
    6] Do we need to involve SAP AG for MDMP to Unicode system integrations(As per SAP Note: 656350) ?
    Thanks and Regards,
    Ananth

    Hi Ananth,
    as you have already mentioned, you need differents RFC destinations for each language. So you have to make sure, that the IDocs use the right destination according to there content.
    If you have messages from PI to MDMP it is the same, you need different channels with different logon languages as well. You need an identifier in the message, that can be used for selecting the correct channel.
    It should not be a restricting to any IDoc type, but it is not possible to post a message with different languages (which require different codepages) in one IDoc.
    For correct conversion from a non unicode system to unicode, the codepages have to be installed in th OS of the PI server.
    Regards
    Stefan

  • Configure Training and Verification System with CUP

    Hi gurus
    Has anyone done this successfully?
    Need tips.
    I already have the configuration document but I believe the information is not sufficient. for example. The web Service URI for the system etc? We opened a ticket with SAP and the response is also not sufficient. This is the response
    "Here is the how-to guide on the customer BPX that shows how to
    set up a training and verification system. Copy and paste all three
    lines into your browser.
    http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/b058a83c-038e-2b10-e9ab-c9b79f565edd?quicklink=index&overridelayout
    =true
    Here is the general link to all how-to guides and articles on the
    SDN for GRC.
    http://wiki.sdn.sap.com/wiki/display/BPX/Governance%2C+Risk%2
    CandCompliance%28GRC%29How-To+Guides
    After you have downloaded the guide, please close this message
    when completed."
    There is a snapshot on page 9 and 10 of the document. Any idea what that is?

    Robert,
    this is no plug&play configuration. Most likely your system does not even offer that web service, so you will have to get a programmer to write the interface.
    CUP will call the web service and hand over the role information from the request, then the training system will have to return whether training has been passed for each role or not.
    The guide is quite detailed - I suggest you talk to someone local who understands your environment and can help you creating the web service.
    Frank.

  • The battery of my ipod touch 5g is charging and discharging so fast, why?

    hi. recently i bought an ipod touch 5g, and also i bought an usb power adapter 5w of apple, and the situation is that the battery charge in two hours not in four, and also the batterie tends to discharge a little but faster, so i want to know what do i have to do? thanks

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                                
    iOS: How to back up                                                                                     
    - Restore to factory settings/new iOS device.             
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
      Apple Retail Store - Genius Bar

  • NOKIA X2 charging and discharging cycles & update

    Being a NOKIA enthusiast, I got the Nokia X2 phone despite the overwhelming negative reviews it was getting. While it does have a number of shortcomings, all nokia bias asid, its a fairly good phone. But the one problem that really irks me is the VERY short battery timing. The phone CHARGES as well as DISCHARGES very quickly.
    Each time I use the browser or any other app for a few minutes (usually less than five minutes), a few percent of battery is out. At this rate, my phone does not even last for one whole day.
    I want to know if
    -1 any of you users have the same problem as I do?
    -2 do other X series phones have battery issues -
    3 does it have anything to do with the 2.1 update? since the update, some odd feature like opera browser, or messages (which arent even running)  or SCREEN consumes 20-25 percent of the battery.
    -4 Is it likely that this issue will be solved in a coming update and whether is it even possible to solve the issue with an update?
    Since if it is the processes running unnecessarily that guzzle all the juice then it might be so but if it is a fault in the design then we're probably stuck with this issue for the rest of the Nokia X2 period?

    Hi, Kaefi333.
    Thank you for choosing Nokia. 
    Let us help you with this. Have you tried these workarounds: http://www.microsoft.com/en-in/mobile/support/product/nokia-x2-dual-sim/userguidance/?action=singleT...? 
    Apart from the workarounds on the link provided above, you can also try this: Nokia X2 Dual SIM - Restore the original settings. 
    For your next questions: 
    Check this: http://discussions.nokia.com/t5/Nokia-X/Nokia-x2-Battery-Problem/m-p/2959065#M4512. 
    None that we know of . 
    To know more about the features included in the 2.1 software, go here: New software update for Nokia X2 Dual SIM: Nokia X Software Platform 2.1 (2.1.0.11). 
    We cannot comment about future updates. We hope you understand.
    We look forward to your reply & welcome to the Nokia Support Discussions. 

Maybe you are looking for