Want to change latency type on my line

Last year I had a new line laid into my home after 3 years of problems with the old one. Earlier this year I opted for the upto 20 Meg speed, my line is outputting around 18.6 which is fine however recently i've been experiencing disruption to my line.
Sometimes the Hub will reset itself, then when it comes on the broadband light flashes yellow for ages whilst the other lights are blue sometimes upto 5 mins will go by, requiring me to reset it manually to achieve a stable blue light & connection.
I've checked my latency type and found its interleaved. My old line was Fast type as I a game alot and I need a fast stable connection. I think it must have been an oversight when they connected my new line at the exchange they forgot to use the same settings, I do have an I-plate installed so its not an interference thing either.
Is there anyway I can get my Latency set to Fast type please?. My download speeds are stable although sometimes erratic so its not a line problem I have just an exchange setting.

DC74 wrote:
Right, then clearly theres something not quite right with my line then, shouldn't be taking ages to re-sync after a reset. Is fast latency still better for gamers though?
Depends on your definition of "better for gamers".....
You either have an interleaved connection that affords stability, maintained IP profile, and maximum sync rate, with maybe the addition of roughly 20-40 milliseconds latency to server connections, as a worst case scenario.
Or you have a slightly lower latency connection, with no forward error correction, possible rise in noise margin, resulting in lower sync speeds and associated IP profile and throughput.
A no brainer really .... over to you.

Similar Messages

How to change latency type to fast?

How to change latency type to fast?

ADSL Line Status
Connection information
Line state:
Connected
Connection time:
5 days, 03:08:00
Downstream:
16,403 Kbps
Upstream:
948 Kbps
ADSL settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
3.1 dB / 4.7 dB
Line attenuation (Down/Up):
30.5 dB / 16.2 dB
Output power (Down/Up):
20.9 dBm / 12.2 dBm
FEC Events (Down/Up):
313987846 / 3701
CRC Events (Down/Up):
2155 / 18271
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
HEC Errors (Down/Up):
49173 / 14016
Error Seconds (Local/Remote):
0 / 17361

I want to change Material Type for mass upload.(MMAM)

hi all,
I want to change Material Type for mass upload.(MMAM)
Suggestion pls? or Any BAPI is availablre?
Edited by: abap_friends on Jan 6, 2011 7:12 AM
Moderator message: please do your own research before asking.
Edited by: Thomas Zloch on Jan 6, 2011 11:27 AM

This may be little tough for 10000 sales orders.
1. You have to remove the output record for the irrelevant output record using tcode VV12 for the relevant document type. So now for the document type, the old output wont be triggered.
2. Now, create output records for hte correct output type in VV11 tcode(for the output type BA03) for the document type. Now this output will be triggered for all the document types you are creating from now onwards.
3. To trigger the output type BA03, in all the old orders, you just have to open these sales orders in change mode (VA02), and just save it. When u open it the output type BA03 will be automatically triggered as the master data is maintained in VV11. But because just opening all the 10000 sales orders in VA02 one by one be a mechanical task, you have to think of some tool for this.
May be a CATT procedure can do the trick. Else, you can just create a small program, where you can upload these sales orders and the program will just open these orders in change mode and just saves it (without making any changes). Then the output will be retriggered.
Here again, if you are printing the output directly, it is advisable to trigger the output in batch mode(Date/Time field is 1 in VV11), and then you can again trigger the printing again using the program RSNAST00 after office hours for these 10k orders.
I hope I answered ur query.
Pls lemme know if you need some more info. (You can reward me too...)

Want to Change Latency from "Interleaved" To "Fast...

I used to have "Fast" latency which helped smooth play on xbox live, but when i turned my router on and off over a period of a few days (When i was rearranging my room) i noticed that my internet had slowed down, i checked and i had an "Interleaved" latency type! I wish to go back to "Fast" as it helped.
Thanks.

Hi Welcome to the forums
Here is a basic guide to getting help from the community members done by CL Keith Please read through the link posted http://forumhelp.dyndns.info/speed/first_steps.html
once you have posted the information asked for then the community members can help you more
Thank You
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

I want to change the type of a Result Set

Hello all,
I was using a ResultSet object to store the results of a query, and when i attempted to use the ResultSet function "last()", i had a SQL exception saying that I cannot use this function on a ResultSet of type TYPE_FORWARD_ONLY. How can I change the type of a ResultSet to be for example TYPE_SCROLL_SENSITIVE, so that i can use the 'last()' function? I can only find a function caleed getType() but i want a function to allow me to set the type of the ResultSet.....
Thanks a lot

The type is determined when you create the Statement or PreparedStatement object. See the documention for Connection.createStatement or Connection.prepareStatement.

BT Infinity - Changing Latency type

Hello!
I have read a few articles that say that you cant change your latency type from Interleaved to Fast Path with BT Infinity because the modem is in a little white box and not part of the HH.
This is only the case for some people though. I still connect with the telephone wire and not the WAN port. I have always had a brilliant connection (noise wise etc.) and have always hit the theoretic max of my broadband on ADSL2 and now VDSL.
Would I be able to request my latency type be changed to Fast Path (as I assume it isn't that, although you can't tell with modern HH's) as I do not have this seperate modem box?
Thanks,
Craig

That's right, you can't. DLM handles the transition automatically.
If you found this post helpful, please click on the star on the left
If not, I'll try again

Changing latency type to interleaved

How could I get that done?
Thanks for assistance

ADSL Line Status
Connection information
Line state:
Connected
Connection time:
0 day, 17:13:09
Downstream:
15,892 Kbps
Upstream:
992 Kbps
ADSL settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Fast
Noise margin (Down/Up):
6.4 dB / 5.2 dB
Line attenuation (Down/Up):
30.5 dB / 16.3 dB
Output power (Down/Up):
21.0 dBm / 12.1 dBm
FEC Events (Down/Up):
0 / 0
CRC Events (Down/Up):
1690 / 3885
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
HEC Errors (Down/Up):
15105 / 3884
Error Seconds (Local/Remote):
0 / 3573

Changing latency type to fastpath

I would like to have my latency type changed from interleaving to fastpath I have asked previously via live chat and they didnt end up changing it for me, thanks.
Solved!
Go to Solution.

You would need to provide connection information here, and get advice from forum members before anything could be done.
What are your ADSL Statistics and BT Speedtester results please?
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Change Valution Type in Delivery Line Item

Hi ,
I have a requirement to change the material Valution type only in Delivery Document Item data (VL02N) .
I used the below BAPI BAPI_OUTB_DELIVERY_CHANGE(Giving an error Error in document &1 item &2 (quantity consistency check) )
I have also tried the FM LE_MOB_DELIVERY_UPDATE , The program saves without any error but not actually saving in the document.
Could any one help me in suggesting good FM to update Material Valution type in the Delivery Item .
Thanks,
Vijay.

Dear Sudarshan,
As per my knowledge ,In standard there is no configuration which triggers exactly double the sales order qty in delivery.
Either it might be due to some customer development or maybe some mistake in the observation.
As mentioned in the previous posts, if its 2 line items in the delivery istead of one in the sales order, it will be batch determination.
Also, please check whether this QTY doubling phenomenon is happening for other order type also.
Check and revert back.
Thanks & Regards,
Hegal K Charles

Want to change data type CHAR32 to CHAR40 in cutomized function module(CRM)

Hi Friends,
I have a requirement to change the data type CHAR32 to char40 .
Pls guide me how to do it.do I need to change it directly or we have do anymore changes?
Thx in Adv.
Baba

Hello Baba,
In my opinion the length of a data field has little to do with the ITS and it's templates. You should be able to change the length for your function module and then the new length should work on the ITS if using the Webgui. If you have custom templates then maybe you will need to recreate the templates or modify the field length, but this is second to actually changing the datatype length in the R/3 system.
Edgar

Want to change output type for 10000 sales orders through MASS

Hi Friends,
I would like to change the Output type in the sales order for 10000 sales orders.
Can I do with MASS transaction. If so, Plz let me know how ?
Is there any other process to change the output type for 10000 sales orders, as its difficult to manually in each and every sales order.
Its very urgent issue, Plz let me know at the earliest.
Thanks & Regards,
Praveen Kumar. A

This may be little tough for 10000 sales orders.
1. You have to remove the output record for the irrelevant output record using tcode VV12 for the relevant document type. So now for the document type, the old output wont be triggered.
2. Now, create output records for hte correct output type in VV11 tcode(for the output type BA03) for the document type. Now this output will be triggered for all the document types you are creating from now onwards.
3. To trigger the output type BA03, in all the old orders, you just have to open these sales orders in change mode (VA02), and just save it. When u open it the output type BA03 will be automatically triggered as the master data is maintained in VV11. But because just opening all the 10000 sales orders in VA02 one by one be a mechanical task, you have to think of some tool for this.
May be a CATT procedure can do the trick. Else, you can just create a small program, where you can upload these sales orders and the program will just open these orders in change mode and just saves it (without making any changes). Then the output will be retriggered.
Here again, if you are printing the output directly, it is advisable to trigger the output in batch mode(Date/Time field is 1 in VV11), and then you can again trigger the printing again using the program RSNAST00 after office hours for these 10k orders.
I hope I answered ur query.
Pls lemme know if you need some more info. (You can reward me too...)

Want to change network type on huawei e220 ?

Any one can help,I use huawei e220 on my macbook pro,but how can I change the network type 3G only,3G Prefer,Gsm Only,Gsm Prefer ?

Hi AFU;
Since your question pertains to networking, you might have better luck if instead of posting it here for questions on using Leopard, you posted it in the Networking Forum instead
Allan

I want to change Document Type of DIR in Prodution for DMS Document

Hi Expert,
I have requirement to change to document type of the DIR which are uploaded and available right now in Production Server.
If anyone knows BAPI of any procedure to do the same pls let me know.
Thanks,
Jay.

Not possible.

I want to change the "blinking solid line cursor" to something that is easier to see when typing in a url or like on this line where I type this question.

I want to change the "solid straight blinking line"....to something easier to see. It is really hard to see it especially in the box where one types in a URL. Thanks

You can widen the "I-beam" cursor but if I recall correctly, the thicker it gets the more it will overlap the text to some extent so that can sometimes affect readability.
The following thread has the "under the hood" settings for this: [https://support.mozilla.org/en-US/questions/900479 Size of the text cursor (insertion point)?]
Can you get a display that you like?
''Edit: The problem I remembered was when the blinking was turned off. See [https://support.mozilla.org/en-US/questions/949937 i need smth like `ui.caretInvert: true`].''

How can I change the thickness of a line in a Picture object?

I want to change the thickness of the line in a Polar Plot. I can easy change the color but not the thickness of the line displaying the data. I have seen that the 'polar Plot' function use the 'Draw Line' function of the 'Picture Functions'. Do you have a solution? Thanks in advance.

Hi Jean-Michel,
If you dig down a few levels from the top-level Polar Plot VI, you will find vi.lib\picture\polarplt.llb\Plot Polar Data.vi. Inside this VI is a VI called "Draw Multiple Lines.vi", which has a "pen" input. This input is currently not wired, so it defaults to a line style of "Solid", and a width of "1". If you take this input and propogate it all the way up to the top-level Polar Plot VI, you can now specify the line width and style of your polar plot.
I have submitted this as a suggestion, so perhaps we will see it in a future version of LabVIEW.
-D
Darren Nattinger, CLA
LabVIEW Artisan and Nugget Penman

Want to change latency type on my line

Similar Messages

Maybe you are looking for