Want to connect HP Laserjet 8150n directly to MacBook Pro (late 2009) via Ethernet cable only

This seems like it should be so simple. I have this hulking laser printer that is wonderful, but I only use it occasionally for large, high-quality, final B&W publisher proofs. I want to put it in a corner upstairs and just take my laptop up to connect directly and print when necessary (no cabling up there). Because it's an older, network printer, it only has an ethernet port, a parallel port, but no USB port. Apparently there's a JetSend IP address (10.0.1.11), but this doesn't seem to have significance with IP printing. Any suggestions would be greatly appreciated. Otherwise, I'm going to have to get rid of it.

Found a perfect solution from HP Mac Architect at:
https://discussions.apple.com/message/10428063#10428063
Be sure to configure IP manually, by entering a local IP address for your Mac Ethernet, such as 192.168.1.5, instead of using DHCP. Add this as a new location, and click the Apply button. This way, you can switch back if necessary.
If you've printed the Configuration page from your HP 8150n printer, you can try entering the JetSend IP address. If the correct HP printer driver doesn't pop up, do the Cold Reset (turn off the power, then turn it back on, holding down the Go button so the status reads "COLD RESET") to force your printer to find a new IP address. Give it about 30 seconds to initialize before printing the Config page.
Back on the Mac, when you add a new printer in the System Prefs > Print and Fax dialog, choose the IP tab.
Enter the printer's IP address from the Configuration page that you print.
The correct HP printer driver pops right up, and you're golden.
THANKS, ANDREW!!!

Similar Messages

I want to connect a Windows PC to an existing Airport Extreme router via ethernet connection. Is there any utility required or can I just plug into the router?

I want to connect a Windows PC to an existing Airport Extreme router via ethernet connection. Is there any utility required or can I just plug into the router? The router is already set up and working with existing iMacs.

thanks for the info. I found apple utilty software on this windows 7 PC but I guess it is not required for sharing internet on exisiting apple extreme. Am I correct that I can remove this apple software?

Connecting HP Laserjet 2100 to OS 10.4.8 Powerbook via ethernet

I have been trying unsuccessfully to connect my Laserjet 2100 printer with ethernet card directly to my mac via an ethernet cable. I have tried adding the printer directly by going to Add Printer under System Preferences, entering the HP Jetsend Address (169.230.14.45), and using either HP Laserjet 2100 series drivers or HP laserjet 5 series (gimpprint) drivers. I still am not able to print. Can someone walk me through the process to get the two talking? Thanks in advance.

The IP address you listed is a self-assigned address, which won't work. You need to manually assign IP addresses to both computer and Printer/Jetdirect in the same local subnet range, like 192.168.1.5 and 192.168.1.6.
Then Add the printer using the IP > HP Jetdirect protocol. And I think HP Laserjet 6 Series works better than 5 Series (Try both).

Help connecting 2TB Time Capsule to iMac via ethernet cable only

I have an iMac running OS X Version 10.9.3, and a 2 TB Time Capsule, which at our last residence I used both as my wireless router and Time Machine backup (via wi-fi). We recently moved and got Comcast, which provided us with a very, very fast router. As a result, I would like to start using the Time Capsule only as a Time Machine backup, preferably via an ethernet cable connection. I tried connecting the Time Capsule to the iMac via an ethernet cable with no joy. When I did, it seemed to bring back my old wireless network, which I don't want. Any help/advice would be greatly appreciated!

Is it something specific about the Comcast modem/router that makes it so I have to plug an ethernet cable into it too (as opposed to just running an ethernet cable directly from my iMac to the Time Capsule, which is what I assumed was possible and was hoping to do)?
Nothing specific about the Comcast modem/router, but definitely something specific about the Time Capsule in that it needs to connect to the Comcast modem/router over a wired connection to allow backups to occur over the Comcast wireless network. As we have said, the Time Capsule must connect to the Comcast modem/router using an Ethernet cable, as you see illustrated in the TC Setup Guide.
This solution doesn't really work, as our computer/TC is upstairs and the Comcast modem/router is downstairs.
Ethernet cabling can be run 300+ feet, or about 100 meters with virtually no signal loss, so you should be able to locate the Time Capsule anywhere that you want. My Time Capsule is located in a closet, about 60-70 feet away from the main router.
is there a way that I can use the TC as an upstairs wifi extender and still do my Time Machine back-ups wirelessly?
Yes. When the TC connects to the Comcast modem/router using an Ethernet connection, you could use the wireless capability of the TC to create a wireless network with the same wireless network name and password as the Comcast network. Then, you will have the same network upstairs and downstairs with much greater range.
You will be able to backup to the TC using wireless....or, if you prefer a much faster connection....connect an Ethernet cable from your Mac to one of the LAN <--> ports on the TC.
For example, let's say that you are making the first backup from your Mac to the TC when everything on the Mac is copied over to the TC. Typically, this might take 8-10 hours on average using wireless, but Ethernet would require only about 2-3 hours.
Once you have the first complete backup done, you could then perform subsequent backups over wireless, since these will only take a few minutes each time that the Mac backs up with only the changes that have occurred since the last backup.

Connecting HP Pavilion 23xi to a Macbook Pro late 2013

I have just bought a HP Pavilion 23xi monitor as an addition for my Macbook Pro 13in Retina Display late 2013 model. I am wondering and needing to know the best way to successfully connect them both together. Please note I am using the pre-release version of the OS X Yosemite, if that makes a difference which I hope it doesn't.

Yes, I see now. The model number did not register in the old mind correctly. The Pavilion 23xi uses D-Sub, DVI, HDMI for connections. I would recommend the DVI, which means you need " a DVI output using Mini DisplayPort to DVI Adapter (sold separately)" copied directly from the Mac webpage HERE
{---------- Please click the "Thumbs Up" to say thanks for helping.
Please click "Accept As Solution" if my help has solved your problem. ----------}
This is a user supported forum. I am a volunteer and I do not work for HP.

Can't connect to work server (windows) on MacBook Pro through VPN - via router

Due to the nature of my job now, I am working remotely.
The IT department hooked me up with a MacBook Pro that connects to our work server, which I know is Windows-based, via a VPN. The VPN connects just fine; however, when I go to connect to the server—it doesn't find it. It gives me:
The server “dc03” may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again.
Interestingly enough, the first time I used it (at Starbucks, then McDonald's) it worked, but at home it wouldn't. We isolated the issue to the router, since I could do it when plugged in, but no one could figure out what kind of settings were different or weird. I went to the store and bought 2 other routers. One worked, the Linksys, but the Belkin did. WHAT? So the cheaper one worked? This was the easiest solution, because still don't know the bottom line: why?
Now, a local spot in town that I frequent—one that used to allow me to connect to my work server—changed routers (the "newest, fastest" AVIS). So now, I cannot connect and get that same message.
My IT guys are stumped. I don't personally know enough about this side of technology to be of any use.
Does anyone have any idea what's going on?

What is the make & model of the new wireless router that you ISP has provided you? Are you able to administer it if needed?
For the MacBook Pro, try the following, in order, until (hopefully) resolved:
1a. Delete Preferred Network(s)
System Preferences > Network > Wi-Fi > Advanced > Wi-Fi tab
Under "Preferred Networks," delete the network(s) you regularly use from the list.
1b. Delete AirPort Keychain Entries
Launch the "Keychain Access" application located in Applications/Utilties.
In the windows on the left side: Select login for Keychains and "All Items" for Category.
Click on the "Kind" filter at the top, and look for any "AirPort network password" entries...and delete them.
1c. Add Preferred Network(s)
System Preferences > Network > Wi-Fi > Advanced > Wi-Fi tab
Add the preferred network(s) using the "+" button.
Restart or log out then back in.
2. Move System Configuration Files
(Note: You will have to reestablish your network connections settings.)
Go to /Library/Preferences
Move the SystemConfiguration folder to the desktop.
Restart your Mac. (Note: OS X will rebuild the files that are now sitting on your desktop. If this doesn't resolve the issue, you can move the folder back to it's original location.)

MacBook Pro does not recognize Ethernet cable or connect to wireless

Today when I turned on my computer, it suddenly would not recognize any kind of Internet connection. The Ethernet cable that I use every day now shows up as 'unplugged' even though it is plugged in. I have tried using a different cable, and it still shows up as unplugged. When I try to connect to the Internet wirelessly, there is always a connection timeout and I can't connect. I use a self-assigned IP address and I've never had this problem before. I've also reset my PRAM, but it hasn't helped. Any suggestions?

try suggestion by "KYLEWONT". If you are still unable to connect to internet then issue is either with n/w settings on comp or h/w. You can drag & drop systemconfig folder in MacHD/Library to desktop which contains all settings for network. Restart comp & that should fix problem related to s/w.

HT5219 Can I connect my thunderbolt monitor to my MacBook Pro and iMac at the same time

I am wanting to connect my thunderbolt monitor to my MacBook Pro as a secondary monitor when running programs in windows 7 thru boot camp, and also have it connected to my iMac as a secondary monitor when working thru apps on my iMac. Is there a way to do this without having to connect and disconnect cables each time I want to switch.

I don't think it can be done without a KVM switch, & not sure they can handle that resolution.

I have an HP LaserJet 8150N that I am trying to get connected via ethernet cable directly to my iMac. I always had this printer connected via a network so I don't know if I am able to connect directly with a cable since it is a network printer.

I have an HP LaserJet 8150N that I use for my work and I have had this printer for ever and it is one heck of a work horse! I am trying to get it connected via ethernet cable directly to my iMac. I always had this printer connected via a network so I don't know if I am able to connect directly with a cable since it is a network printer. I have tried to reconfigure the printer using the JetDirect menu giving it a new IP address but still no luck. If anyone could help me through this issue I would appreciate it.

moonlightcaravan wrote:
Second, seeing "connecting" and connection failed is normal. You must click on "Connect As" in the Finder window and then enter the username and password for the admin account on the other computer. That should fix things.
Thanks for responding.
When does clicking on "Connect As" happen in the process above?
After step six? Seven?
After the connection has failed?
Is this the FInder window that shows the icon of the computer you want to copy the file from?
You should see "Connect As" in the Finder near the top right of the window as shown below:
!http://blog.brothersoft.com/wp-content/uploads/2008/11/howto_copy_files_to_or_from_your_iphone02.jpg!

HT1515 My internet 3rd party access point in in the basement and the speakers I want to stream music to wirelessly are upstairs. Does Airport Express need to be connected to my 3rd party router via ethernet cable or will it stream music wirelessly?

My internet 3rd party access point in in the basement and the speakers I want to stream music to wirelessly are upstairs. Does Airport Express need to be connected to my 3rd party router via ethernet cable or will it stream music wirelessly?

Wirelessly
Just select the option to make your AirPort Express join an existing network in the setup process

I have att u verse modem and it wifi was not working. So i got netgear wifi an d i connected my apple tv via ethernet cable to att uverse modem . i did not want slow dowm my wi fi speed. Now airplay is not working .

i have att u verse modem and it wi fi was not working. So i got net gear wi fi and connected to att modem . i connected my apple TV via Ethernet cable to att uverse modem . i did not want slow down my wi fi speed. My Apple phone is on Netgear wifi .Now airplay is not working .

Make sure that the Att Modem goes to the netgear router via ethernet cable. Then connect your Apple Tv with a ethernet cable to the back of the net gear router. Airplay wants it to both be connected to the same device, usually.

Want to connect my ViewSonic to my mac book pro

How do I connect my ViewSonic monitor to my macbook pro?

You connect it to the computer's video port, using an adapter if needed. If the computer has a Thunderbolt port, use a Mini DisplayPort cable or adapter.
(102396)

Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.

Hi!
Didn't know exactly where to direct this question in the Apple Community so I chose Airport. To everyone, thanks in advance.
I’m really desperate. I’m a big Apple fan. I have two Apple MacBook Pro laptops with Mountain Lion software. I also have an Apple Airport Extreme. My HP Photosmart C4780 printer was also purchased from Apple. Anyway, my Internet service is AT&T. AT&T just upgraded my service with a new modem/router (AT&T U-Verse). Prior to the conversion, my wireless printer connection was working perfectly.
Now can’t print wirelessly. For your information, everything is connected via Wi-Fi. The AT&T technician stated that I no longer needed my Apple Airport Extreme, so it was removed. Naturally, after the tech leaves, we find out the HP printer wirelessly no longer works. Thinking that removing Airport Extreme may have been the problem, I reconnected it to the AT&T modem/router, however no change.
This appears to be an HP printer problem. I went to HP community support with the information below but I have received no solutions outside of buying a new printer.
“Ran the HP wireless network test report and it states that HP printer can’t find wireless router and to verify that the HP printer network name (SSID) matches the wireless router network name (SSID) exactly. The Diagnostic Summary in brief: Wireless On & Working & Security – Pass; Network Name (SSID) Found – Fail. Nothing else under diagnostic summary ran. Under Configuration Summary: It shows old SSID name and Mac Hardware Address but no IP Address.
Next ran the Network Configuration Page and everything is enabled except the 802.11 Wireless. It shows status – disconnected. Under general information it states the following: Network status - Offline; Active Connection Type - None; URL(s) for Embedded Web Server – http://0.0.0.0.”
To be straightforward, I’m no computer tech so I don’t know what this means or where to find. The AT&T tech provided me the new SSID Name and a wireless key number but that’s it. Also I uninstalled and reinstalled via USB. The HP message states can’t find router. At this point, I’ve tried everything to reconfigure without success. If I need to make these changes via Airport Extreme Utility 6.0 not easy to find not that I know what I’m doing.
Most importantly if I ever get wireless working again, do I still need Airport Extreme connection or is the AT&T U-Verse modem/router sufficient?
Any direction or help is greatly appreciated. Thank you for listening.

Thank you for your prompt response. I'll be honest I'm a retiree and a newbie to all of this stuff. I don't even know how to do a thread. (Embarassing) This is my first ever contact with the Apple Community so I'm slowly trying to figure this out as well.
As to your thread request, I'm assuming you want to read my post with HP. Not knowing how to thread, I've copied it below.
I have an Apple MacBook Pro laptop with Mountain Lion software. I also have an Apple Airport Extreme. My Internet service is AT&T. AT&T just upgraded my service with a new modem/router (AT&T U-Verse). Prior to the conversion, my wireless printer connection was working perfectly.
Now can’t print wirelessly. For your information, everything is connected via Wi-Fi. The AT&T technician stated that I no longer needed my Apple Airport Extreme, so it was removed. Naturally, after the tech leaves, we find out the HP printer wirelessly no longer works. Thinking that removing Airport Extreme may have been the problem, I reconnected it to the AT&T modem/router, however no change.
Ran the HP wireless network test report and it states that HP printer can’t find wireless router and to verify that the HP printer network name (SSID) matches the wireless router network name (SSID) exactly. The Diagnostic Summary in brief: Wireless On & Working & Security – Pass; Network Name (SSID) Found – Fail. Nothing else under diagnostic summary ran. Under Configuration Summary: It shows old SSID name and Mac Hardware Address but no IP Address.
Next ran the Network Configuration Page and everything is enabled except the 802.11 Wireless. It shows status – disconnected. Under general information it states the following: Network status - Offline; Active Connection Type - None; URL(s) for Embedded Web Server – http://0.0.0.0
To be honest, don’t know what this means or where to find. The AT&T tech provided me the new SSID Name and a wireless key number but that’s it. Also I uninstalled and reinstalled via USB. The HP message states can’t find router. At this point, I’ve read your forum and tried everything to reconfigure without success. Any direction or help is greatly appreciated.
Thanks in advance!
Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.
I finally figured it out! (Sorry that I'm replying to my own posts btw, but I want to post the solution for anybody else with the SigmaplusEOL1 problem). If you have the SigmaplusEOL1 as your SSID when you print the "Wireless Network Test Report", you do NOT need to return it (I know that's hassle for people). To fix the problem, follow these steps.
1) Unplug your printer.
2) Go to your router's IP address (like 192.168.1.1 or whatever it is for your router).
3) Change the SSID of your wirelss network to "SigmaplusEOL1".
4) For the Security option for your wireless network select none (so that a password is not required to access your wireless network).
5) Power your printer back on and reprint "Wireless Network Test Repor". It should say "No problem found..."
6) The report should also have a the IP Address of the printer (under Configuration Summary at the bottom). Type that IP Address in your browser to get to the printer's settings page.
7) Click the "Network" Tab at the top.
8) Under the "Connections" header in the left pane, click "Wireless (802.11).
9) Click "Start Wizard" at the bottom right.
10) In the wizard, change the SSID and encryption (wep or wpsk) password to whatever you want your wireless network to be. So probably whatever it started out as before you changed the SSID to SigmaplusEOL1
11) Click "Finish" at the end. The page will probably try to keep loading but it won't because you changed the network settings of the printer. Just ignore that
12) Go back to your router's IP address and change the SSID and encryption password to whatever you changed the printer's SSID and password to.
13). Reprint the Wireless Network Test Report. It should say the SSID is the same as your wireless, and everything is good.
That's it. You should be good to go now.
Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.
Thank you for your prompt response. This has been a totally frustrating experience. I’ve spent at least 8 hours trying to fix this. My HP problems and your initial steps were identical to mine. I am by no means a tech person and my computer tech knowledge is minimal. However I followed your steps to the best of my ability.
I did get the SigmaplusEOL1 message. I was able to get to Step 6 where the wireless network test report now reads – “HP printer settings do not match your wireless router settings.” So I guess this is a step in the right direction. However unfortunately the Configuration summary message for the IP Address reads – “Not Applicable”. (Note: changing SigmaplusEOL1 to network name knocked out my Internet access. Had to switch back to regular network name to regain access.)
I’m at a loss as to what to do next.   Without the IP Address is it possible to move forward? As I stated earlier, I’m not a tech person. As to your steps 7, 8 and 9, I can’t find them on my computer or maybe I’m looking in the wrong places. In System Preferences - Network, I have none of these steps. If you’re referring to Airport Utility, with the changes in Mountain Lion, these steps are no longer there. If you’re talking about Safari, Firefox or HP, now I’m really lost.
Finally, I don’t know if you can answer this or not. If I ever get wireless working, do I still need Airport Extreme or is the AT&T U-Verse modem/router sufficient?
Again thank you for your time and patience.
Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.
Unfortunately I am unable to offer any further advice as I only followed the instructions listed on the other page.
Finally, as to having WEP enabled, I don't know. Don't even know where to look. The best that I could determine is that my security is WPA/WPA2 Personal.
I'm truly sorry about all of this. Thank you for your time and patience. After reading all of this and you change your mind, I would understand.

I want to use my iPod Classic with my MacBook Pro, I am using it on my G5

I have me iPod Classic, on my G5. This is where all the content on the iPod is from. I want to be able to connect my iPod Classic to my MacBook Pro and be able to have the iPod show up, on the devices list where I could access all my music, playlists and podcasts. Where can I find information on how to do this?
Thanks in advance for reading and replying to my post.
Sebastian

If you want to connect and use an iPod on more than one computer or with more than one library you need to change the update preference in the iPod Summary tab to "Manually manage music and videos" and click Apply. The content of iTunes and the iPod are not syncronised in this mode so the two can be different. You can directly access the content of the iPod and play it through iTunes and you can drag and drop whatever you want to the iPod from either library:
Using iPod with Multiple computers
Managing content manually on iPod
Syncing Music to iPod
Something else to be aware of when using an iPod in manual mode is that the "Do Not Disconnect" message will remain on the display until you physically eject the device: Safely Disconnect IPod

I want to transfer my iPhoto from my old MacBook Pro to my new MacBook Pro. I have a firewire or I could also do it from my TimeCapsule. Would one be a better method than the other?

I want to transfer my iPhoto from my old MacBook Pro to my new MacBook Pro. I have a firewire or I could also do it from my TimeCapsule. Would one be a better method than the other?

Hi brotherbrown,
A direct FireWire transfer (especially if it's 800 to 800) is going to be the fastest method. TimeCapsule would work, if you connect to it via Ethernet, via wireless it would be quite slow (especially if you have a large library).

Want to connect HP Laserjet 8150n directly to MacBook Pro (late 2009) via Ethernet cable only

Similar Messages

Maybe you are looking for