Want to globally manage all Wireless devices with wired ones using SNMP

Wired devices are already managed, but wireless devices of particular interest which I desire to manage are:
Autonomous:
AIR-AP1121G-J-K9
AIR-AP1121G-J-K9
AIR-AP1131AG-J-K9
AIR-AP1131AG-P-K9
AIR-AP1131AG-J-K9
AIR-AP1131AG-P-K9
AIR-AP1210
AIR-AP1210
AIR-AP1210
AIR-AP1210
AIR-AP1231G-J-K9
AIR-AP1231G-J-K9
AIR-AP1232AG-J-K9
AIR-AP1232AG-P-K9
AIR-AP1232AG-J-K9
AIR-AP1232AG-P-K9
AIR-AP1242AG-P-K9
AIR-AP1242AG-P-K9
WLC
4400 Series Wireless LAN Controller
2100 Series Wireless LAN Controller
3750 Series Integrated Wireless LAN Controller
Is there any single document which compares which traps/alerts are available in which devices/IOS versions or must I pull teeth to compare them?
A simple reference chart/URL would be quite helpful.

The AIR-AP1121G-J-K9 gives off certain traps. What are they?
Likewise, all of the following devices also give off traps.
AIR-AP1121G-J-K9
AIR-AP1131AG-J-K9
AIR-AP1131AG-P-K9
AIR-AP1131AG-J-K9
AIR-AP1131AG-P-K9
AIR-AP1210
AIR-AP1210
AIR-AP1210
AIR-AP1210
AIR-AP1231G-J-K9
AIR-AP1231G-J-K9
AIR-AP1232AG-J-K9
AIR-AP1232AG-P-K9
AIR-AP1232AG-J-K9
AIR-AP1232AG-P-K9
AIR-AP1242AG-P-K9
AIR-AP1242AG-P-K9
WLC
4400 Series Wireless LAN Controller
2100 Series Wireless LAN Controller
3750 Series Integrated Wireless LAN Controller
I'm sure that not all devices list above give off the exact same traps nor do all the devices support the same IOS versions.
That said, looking at which devices support which IOS versions and then looking into each IOS version "ASSUMING" that every device supporting that IOS supports all of those traps is an assumption which network managers cannot take.
So back to my original question.
Where can I find a list of Alerts supported by each of the above listed products?
Walt

Similar Messages

I just set up the airport wireless modem - with a comcast internet router - all wireless device connect seemlessly (3 Iphones, Mac Air, and a Sony Laptop) but my IPAD 1 no longer connects. It tries to but never connects. I have reset it and have utility

I just set up the airport wireless modem - with a comcast internet router - all wireless device connect seemlessly (3 Iphones, Mac Air, and a Sony Laptop) but my IPAD 1 no longer connects. It tries to but never connects. I have reset it and have airprot utility app downloaded on my IPAD - it shows the modem and the internet no connected?

Do you mean an Airport Extreme Base Station connected to a Comcast Modem?

HT4847 Why do I get the answer on trying to open this application, limit reached,want to use skygo on this device visit manage devices to replace a registered device with this one. How do I do that

Why do I get the answer on trying to open the application skygo, limit reached, want to use skygo on this device visit manage devices to replace a registered device with this one. How do I do that. ?

Please see http://help.sky.com/tv/sky-go/register-devices-on-sky-go . Note that if you have in the past already removed one device you will have to wait for a month to elapse before you can remove another.

I have two Apple IDs - one associated with iPad and iPhone and the other associated with iMac and MacAir. I am going to lose the former e-mail address imminently and would like to associate all devices with just one ID. How do I do this? Thanks

I have two Apple IDs - one associated with iPad and iPhone and the other associated with iMac and MacAir. I am going to lose the former e-mail address imminently and would like to associate all devices with just one ID. How do I do this? Thanks

Thanks - I guess it is like there were two of me!
I bought the iPhone first and it seemed natural to link it to the (work) e-mail address which was in constant use. The iMac for home use came next and it seemed natural to use my home e-mail address, particularly as I knew by then that I would lose the work address after my imminent retirement. The same logic went for the recent puchase of the MacAir. I am not sure what happened with the iPad (also a recent purchase) - iTunes seemed to puch me towards the same ID as the iPhone.
It is not a huge problem - just makes my persona look schizoid! Otherwise very happy with everything Apple.

Hello! I have a huge question about how can I get connected my iphone 4 with my car Is there any opption on find my car application? I have a Volvo xc60 and I want to be connected all the time with my iphone. Can I do that?

Hello! I have a huge question about how can I get connected my iphone 4 with my car Is there any opption on find my car application? I have a Volvo xc60 and I want to be connected all the time with my iphone. Can I do that?

Hello. I can say that you have a quite strange „huge question”… It’s non-sense to stay connected with your car which is hundreds miles away. Unless…
I have a theory. You don’t want to controll your car, you want to controll somebody who is driving the car. Volvo XC 60 is a nice family car, usually used by married men between age of 35-45, probably with small children, so it’s very unlikely that you want to controll your teanage kid, mainly because probably even if you would give him/her to drive the car in the neighborhoud, I don’t think that he/she would be „several hundred miles away”… If your child is not young teneage anymore, and he/she has his/her own life, but you want to control him/her, that is sick… So I am convinced that you want to controll your husband who probably travelling often! Am I wright?
Isnt’t nice at all! Would you like if you would be monitorized in such way? I bet you don’t!
Anyway, iPhone is smart, you can use for many things, but come on, you really were thinking that there is such kind of application???
What could you do it's to put in the car a GPS survelling system, however I don't think that you could do it without your husband knowledge, otherwise he won't be able to start the engine...

My mails are syncing across all my devices but the ones read differ from devices

my mails are syncing across all my devices but the ones read differ from each device.

Make sure you are fully updated.
OS X Lion Update 10.7.5 (Client Combo) 1.91 GB
http://support.apple.com/kb/DL1582
If you Control-Click (Right-click) on a folder, select Synchronize now. Does this help? If not you might want to select folder then select Rebuild under Mailbox in the Menu bar.

Is there a way to get around the pop up, "this device is already associated with an Apple ID. You can download past purchases on this device with just one Apple ID every 90 days. This device can be used with another Apple ID in 13 days."Someonehelp please

Is there a way to get around the pop up, "this device is already associated with an Apple ID. You can download past purchases on this device with just one Apple ID every 90 days. This device can be used with another Apple ID in 13 days."Someonehelp please!

What exactly are you trying to do?

HT5622 Why when I try to download songs onto my iPhone from my iPad, it pops up and says "This device is already associated with an Apple ID, You can download past purchases on this device with just one Apple ID every 90 days.

Why when I try to download songs onto my iPhone from my iPad, it pops up and says "This device is already associated with an Apple ID, You can download past purchases on this device with just one Apple ID every 90 days. You cannot associate this device with a different Apple ID for 90 days
(Note, mine says 28 days because I have been waiting for a fair bit for this to go away.)

You can't keep changing the ID you use with iTunes, you are limited to once every 90 days.

Why is my ipad still using battery power when switched off & locked away with no one using it?

Why is my IPad still discharging battery when switched off and locked away - with no one using it? Charged it to 100% on holiday and locked in safe. 2 days later it was at 76%!

How is it "switched off"? Are you pressing the button on the top so the screen goes black? If so, that isn't shut off, but put to sleep. I will still be doing things in the background and using battery power.
To shut it fully off, press and hold the button on top, you will get a notification on the screen that says "Slide to power off". Slide the button and it will turn completly off.
If this is how you switched it off, let us know and we will see what else we can figure out.

Can't log in to Profile Manager or My Devices with Active Directory logins

I have an OSX Lion 10.7.4 Server set up with Profile Manager and it is joined to AD.
I am able to see AD groups in the Profile Manager groups section.
I can also see and add AD users and groups using the server app.
I have enabled the "Can Enable Remote Management" check box for Domain Users through Profile Manager. I have also added Domain Admins to the Workgroup group in the Server app. I'm not sure that I want or need either of these options, but they were suggestions to try.
I am not able to log on to the Profile Manager or My Devices pages with AD logins.
I found these directions about nested groups in Workgroup Manager http://krypted.com/iphone/integrating-mac-os-x-lion-servers-profile-manager-with -active-directory/ but I don't have a com.apple.access_devicemanagement local group or any groups like are shown in the picture.
Any ideas what I'm missing?
Cheers,
Ian

I found the two pieces I was missing:
1) Install the Lion Server Admin Tools
Launch the Server Admin App
Click on the server name in the left pane
Click on the Access button in the upper part of the window
Click on Profile Manager
Either manually add specific groups to the list or if you're feeling brave choose the "Allow all users and groups" radio button
2) Run the command line steps on this page to change the authentication to plain text to support AD authentication:
http://support.apple.com/kb/HT4837
Voila!

Making a vlan for all wireless devices on network

Hello,
We connected 4 wireless access points (AP541N-E-K9) to an SG300-10P switch.
We want to be sure that no wireless clients can alter settings to the network by connecting to any of the networking devices. We also want that no wireless devices (except a few) can connect to computers that are on the wired network.
I'm new to configuring networking devices so I would appreciate a step by step guidance to set up the switch for this.
We already added all the MAC-adresses of all the wireless devices (that are allowed to use the wireless network) to the access points.
Thanks already for your reply.
Wim

Wim,
Look in the administration guide and their are step by step on how to create vlans -page 178
http://www.cisco.com/en/US/docs/switches/lan/csbms/sf30x_sg30x/administration_guide/78-19308-01.pdf
After attempting to configure the switch and run into problems you can give us a call @ 1-866-606-1866 and open a support case
Jasbrayn

I don't want my contacts on all the devices that have iCloud.

I want to be able to have contacts on my phone and not on all the devices too??

You can go to Settings > iCloud on each device and turn Contacts on or off as you wish for that specific device.

Associate a device with a DN using AXL API

Hi guys,
I am trying to add a DN to an existing phone device using AXL API via Java. I keep getting this error:
Devices can only be associated with DNs, Route Patterns and Hunt Pilots.
I have two existing lines on this device which I added through call manager, but now I am trying to add a third one using AXL API. This is what I did to get this error and I am not sure why:
XDirn dn = new XDirn();
dn.setPattern("6340");
XPhoneLine phoneLine = new XPhoneLine();
phoneLine.setDirn(dn);
phoneLine.setAsciiLabel("TESTING - 6340");
phoneLine.setDisplay("TESTING - 6340");
phoneLine.setDisplayAscii("TESTING - 6340");
phoneLine.setLabel("TESTING - 6340");
phoneLine.setBusyTrigger("2");
phoneLine.setIndex("3");
phoneLine.setMaxNumCalls("4");
UpdatePhoneReq updatePhone = new UpdatePhoneReq();
updatePhone.setName("SEPD824BDBBCAF1");
UpdatePhoneReq.Lines newLine = new UpdatePhoneReq.Lines();
newLine.getLine().add(phoneLine);
updatePhone.setLines(newLine);
port.updatePhone(updatePhone);
the error occurs at the last line when I try to push the update.
Thanks

I just tried to execute SQL commands through the API and that is not working well either. The Axlsoaptoolkit.java file works fine but not through the API. this what I have done:
ExecuteSQLQueryReq sqlReq = new ExecuteSQLQueryReq();
sqlReq.setSql("select * from device");
ExecuteSQLQueryRes sqlRes = port.executeSQLQuery(sqlReq);
System.out.println(sqlRes.getReturn().getRow().get(0));
System.out.println(sqlRes.getReturn().getRow().get(1));
System.out.println(sqlRes.getReturn().getRow().get(2));
This returns null on the first 3 rows where I have more than a 1500 entries in that table. I verified using the Axlsoaptoolkit.java app

How to connect many devices with only one FW800 port in iMac?

Hi,
I am upgrading to a new Intel iMac from a 2004 vintage Dual2.0GHz PowerMac. I currently have 8x d2 Quadra drives chained by FW800, and 2x Iomega drives connected vis FW400 hub which also connects HD cams.
My questions is that with only one FW800 port in iMac, I think my devices connectivity is the following?
(1) Get a FW 800 hub (I can only find 2 port ones at the Apple store and BestBuy)
(2) Connect the d2 Quadras to one port of the FW800 hub
(3) Get a FW 800 to FW 400 cable
(4) Connect my 6 port FW400 hub to the 2nd port of the FW800 hub
Thanks for reviewing this solution, and I would also appreciate other suggestions or hear about your experiences if you have a similar set-up.
Will

In addition to your listed considerations, you should consider the following.
Many storage needs do not required FireWire 800 speed. For example, USB 2.0 works fine for your Time Machine backup drive. If you are just storing user data such as your iPhoto or iTunes media files, USB 2.0 is more than fast enough. So, as much as possible, if any of those external drives have USB 2.0 connections and the data storage does not need FireWire 800 speed, offload as much as possible to USB 2.0. I used to be a +FireWire snob+, but since getting an Intel iMac, I find that USB 2.0 works quite well for most data storage purposes.
There are new hard drives that are power efficient and as large as 2TB. Consolidate your data storage needs onto a smaller number of very large drives, partitioned as needed. This will make your setup more reliable (smaller number drives), and save reduce power consumption. If any of your current externals are SATA, you can probably replace the existing drive with an extra large one.
So, I think you setup should be, extra large FireWire 800 drive connected to the FireWire 800 port directly. Using a 9-pin to 6-pin cable, connect the FireWire 400 hub. Connect any non-storage FireWire 400 devices there. Do some data transfer testing to make sure having the 400 hub there on the chain does not cause the 800 connection to slow down.
Connect other drives as needed using USB 2.0, existing or new. Retire the smaller of your external drives.

Has any SAP project integrated an EFTPOS device with ABAP Gui using an ActiveX controller?

Dear Friends, I would like to know, Has any SAP Project integrated an EFTPOS Devise with ABAP Gui using ActiveX Controller? If used could you please share the Technicalities involved in them as we have a suggestion to have the same used in our Project.

Dear Friends, I would like to know, Has any SAP Project integrated an EFTPOS Devise with ABAP Gui using ActiveX Controller? If used could you please share the Technicalities involved in them as we have a suggestion to have the same used in our Project.

Want to globally manage all Wireless devices with wired ones using SNMP

Similar Messages

Maybe you are looking for