Wanted Computer Controled Electronic Cards with Software for Motion Control

Hi everybody
Already worked on designing a cnc table to cut sheet materials.
But we don't know enough for electronics. We think a system which is
software driven from pc. So, we look for Wanted Computer Controled
Electronic Cards with Software for Motion Control but we don't know more
which motors, electronic cards and control panel we have to use.
Please help me. Thanks.
Atilla KESKEKLER
Ahmet Bayman Cad. No 10/4 Otosanayi 4.Levent 80650 Istanbul Turkiye
Tel: + 90 212 270 74 00 Fax: + 90 212 270 75 89
www.aareklam.com.tr [email protected]

Dear Atilla,
You should contact AutomationSolutions (www.AutomationSolutions.com) to receive help with designing your system. They can spec your motors and help you picking the correct controllers and drivers from National Instruments to control the motors that you want to use. Please let me know if you need more information about the capabilities of Motion Control systems from National Instruments.
Thank You,
Morten Jensen
National Instruments

Similar Messages

Card index software for MAC

Does anyone know of some good software that acts like a card-index - somewhere I can store information about books that I read/reviews/quotations? I've tried 'Googling' card-index software for mac, and various other permutations, but not come up with anything that looks any good - or at least I have, but it only works on Windows!
Any suggestions very welcome!
Thanks
iBook G4 Mac OS X (10.4.7)

somewhere I can store information about books that I read/reviews/quotations
Does it have to use a Card Index metaphor? There are many many snippet managers, that will grab things from, say, a web page and store them, index them for fast searching. They will also allow you to make notes etc, or annotate the clippings.
Search on http://www.macupdate.com for (in no particular order)
Voodoo Pad
Mori
Yojimbo
MacJournal
Circus Ponies Notebook
Journler
and many, many more.
Regards
TD

I live in the UK and want to purchase gift cards from iTunes for people in the US but It won't allow me to use my UK address and credit card. Can I or cant I?

I live in the UK and want to purchase gift cards from iTunes for people in the US but It won't allow me to use my UK address and credit card. Can I or cant I?

You would have to work with a retailer selling iTunes cards who would accept a non-US credit card. Best Buy is a possibility; they carry iTunes prepaid cards and will accept orders from other countries:
http://www.bestbuy.com/site/Help-Topics/International-Orders/pcmcat204400050019. c?id=pcmcat204400050019
You'll have to have the order shipped directly to the person in the US (or at least someone with a US address, who could then repackage and resend the cards for you).
Regards.

Want to use credit card with firefox but do not see a lock with firefox 5 on linux using priceline

want to use credit card with firefox but do not see a lock with firefox 5 on linux using priceline

Type '''about:preferences#applications'''<enter> in the address bar.
Now follow the picture.

Is quality better with software for converting VHS to DVD than using an actual converter?

Is quality better with software for converting VHS to DVD than using an actual converter?

Not sure what you mean by "actual converter".
If you mean if you just played a VHS tape to a DVD recorder and recorded like that... You will get close to the quality of the VHS.
If you have a good capture software and hardware you might be able to clean the video and audio up. But VHS is pretty limited in quality.

Windows vista, Ipod shuffle 4th gen. Computer cannot find device driver software for ipod.

After several hours trying the troubleshooting options provided by the apple support site, I have come to what I think is the issue here. My girlfriend recently got an ipod shuffle and when plugging it into her computer the dialog pops up saying it is installing device driver software for the ipod. Eventually it asks me to insert the CD that came with the ipod. No CD came with the ipod, so I click the option that says "I do not have my cd". Then it gives me the option of searching automatically or manually for the driver software. The automatic way can't find it. Doing it manually, with the help of the troubleshooting page, didn't work either. google search can't seem to help me on this one. Also, I tried plugging the ipod into my computer (not hers) and it worked fine, it was able to install the device driver software on its own. Does anybody know the issue here? My computer has windows 7, and hers has vista. Hers is Serice Pack 1. When I tried installing service pack 2 it wouldnt work. I don't know if that is the issue though. I have tried just about everything, I think the issue is finding the device driver software. When I do a google search nothing comes up, so I have no idea what to do at this point. Any help would be appreciated, thanks.

Well its surprising to know that! But even have an ipod shuffle 3rd gen n dint face any problem like that. FYI no cd comes with the ipod jus take ur ipod to an apple exoert n he will solve ur problem .

Credit card swiper & software for Mac

I'm selling my books at a meeting and will have my MacBook with me. What's the best hardware and software for swiping and processing credit cards? There are so many out there, I'd love to get the informed opinion of the Apple community.
I do have a PayPal account, so I can link with that if need be.
Thank you!

I use this: http://www.usbswiper.com/
It got high ratings from EBay and PayPal.

PCMCIA card for motion control

Hi,
I am trying to control a stepper motor through LABVIEW. After perusing through the site, I know that I would need a stepper motor, a corresponding motion controller and a universal motion interface. The problem I have is that I am trying to control the stepper motor through a laptop (which does not have the Parallel Port slot). I am wondering if a PCMCIA card could work (by providing a parallel port to the laptop) or if it would not meet the necessary requirements to operate the motion control through the universal motion interface.
Thanks

It IS possible to drive an UMI interface with a parallel port providing TTL compatible outputs, basically the UMI interfaces are (advanced) break-out boxes feeding the step and direction pulses to a motor driver and connecting feedback signals (encoders, limit switches etc) back to the PC. But in this case, you would have to write your own routines for accelerating and slowing down, as well as evaluating the feedback signals from an encoder or limit switches. There are several manufactures making motor drivers which can be driven via a serial or USB interface, in case you cannot use a NI controller board it will be much easier to use such a setup since the motor drivers usually incorporate at least a basic motor controller providing a set of commands which makes it much easier to control a motor than with doing everything from scratch.

PCI6602 for motion control?

Hi, I am wondering if it is possible to use the pulse generation of the
PCI6602 to control a stepper motor
driver, the problem is that I need aceleration and deceleration in the
pulse train.
I'm using the PCI6602 for event counting (~ MHz), and I need to
synchronize the data acquisition to the stepper motor pulses at a rate
of ~10 KHz. It would be nice to use a single card for both acquisition
and motion control.
thanx,
Stefano

Stefano,
Yes, you could use the PCI-6602 to control a stepper motor. This will require two counters per stepper axis to control the step/dir or CW/CCW lines, or one counter per axis if you only want to move in one direction. You would need to programmatically ramp up the pulse rate to control acceleration. However, since updating the output pulse train frequency is software timed, acceleration may not be very smooth and you risk losing step. Also, you would need to manually handle any pull in moves.
While you could achieve reasonable stepper control with the counter board with some trial and error, the PCI-7334 would probably be a better solution. This controller easily handles acceleration and deceleration and allows you to route the encoder signals over the
RTSI bus to control the data acquisition process.
Regards,
Brent Runnels
Applications Engineer
National Instruments

Controlling multiple videos with one set of controls

I'm currently working on a project that allows the user to view multiple videos at one time. The videos will be exactly the same length and video format/type. I'd like to let the user use just one set of controls to view each video. Is this possible? If so, does anyone have any code samples?
I also want the video to not start when the application starts. I've got that done, but I'd also like the first panel of the video to be displayed. How can I do that?
Thanks!

PS, I'd also prefer for the controls to be detatched from any of the viewers, if possible. Thanks!

Recommmendation for motion control in mid-7604

I got a new mid-7604 recently. So what type of PCI card should I use to control mid-7604 in Labview? Does 6023E or DIO32HS works? Thank you.

Sorry, but I have to add my 2 cents to this thread .
@AK2DM
thank you for suggesting a 73xx device for this purpose instead of a DAQ device
@bighead
apart from the fact, that the 7604's connector is designed to be connected to a 73xx device, there a a lot of functional reasons, why in general a DAQ board is not a good fit for a motion control application. Here you can find some more information about this topic.
Kind regards,
Jochen

What kind of equipment do i need for motion control

i'm new to computerized actuators, i need to control a stepper motor that can turn both directions and can be controlled by a 0-5 volt sensor. i need to be able to set the targeted volts and have it turn one direction if its reading over, and the other direction if its reading under. What should i buy.

Hey Jaspittman,
I would also recommend the following web site called Build Your Own Motion Control System which will walk you through the steps of what you will need to build your motion system. Also, I would suggest taking a look at the Motion Advisor page if you will be using any 3rd party hardware (i.e. motors, drives, stages) which can be found at the following link Advisors for Motion. These two sites have a lot of helpful information to get you started.
Regards,
DJ L.

Tension control in labview using PCI 7354 Motion Control Board

I want to make a program for web tension control of roll to roll system in labview using PCI 7354 Motion Control Board. Is there any interface program that can convert my controller output in a format to be directly used as the input of PCI 7354 (Motion Controller Board) for tension control?
Thank you!

thanks for your reply, i have already make the code of a straight line move and the motor moves successfully, but know i want to put the H-bridge to be able to make a reverse direction for the motor, for your information i only use a PCI-7340 controller and a UMI-7774, where the controller connected to the UMI-7774, the UMI connected to a PWM circuit and the PWM connected to the DC-motor, so what do you think i can do?

Best sd card with class for my Lumia 520 in 32gb

I want to know that which sd card I purchase of 16 gb or 32 gb that will satisfatorily work in my Lumia 520

Welcome to the Linux world. I have been a Linux user for 10 years and I can tell you that you will get no support except from fellow users. Learn to use the Linux user boards and also google.
This might help:
Linux board
put a memory card in the slot and run from the command line:
sudo modprobe usb-storage
If this solves your problem, try adding usb-storage to your /etc/modules file so that when your computer restarts it will automatically load the usb-storage module.
You may even have to manually mount the memory card. Install gparted from apt-get and check if the memory card does not show up as an unmounted storage device...then you can manually mount it by using the command line. You may also have to edit the fstab entries to make it hot pluggable.
Post back if you do not understand any part of this or need more help.

Gift-cards with preorder for iPhone 4?

I am going to pre-order the iPhone 4 online on the 15th and choose to pick it up in the store. But I'm confused about what it means to pre-order.
Are you actually making a purchase? or just reserving an iPhone to purchase in the store?
If you have to buy on-line when you pre-order, can you use 2 or 3 apple gift cards for the purchase? or do you have to use a credit card?
thanks!

You do know that contacts are NOT part of the iTunes backup, right? The only part of contacts that get backed up is the information needed to maintain your favorites and recent call log.
Contacts are meant to live permanently on your computer (Outlook, Address Book) or a cloud-service (Google, iCloud) for safekeeping and archival.
Sounds like you might not have been using your phone as recommended and that your contacts are gone. That's unfortunate. Now might be a good time to review the User Guide to refamiliarize yourself with the way you should be using your phone to minimize data loss in the future.
Good luck.
GDG

Wanted Computer Controled Electronic Cards with Software for Motion Control

Similar Messages

Maybe you are looking for