WAP 121 support for RADIUS COA

Hi,
I am looking into purchasing WAP121 AP product and understand it supports 802.1x RADIUS.
For an intergration with NAC product from Bradford, I need to know if WAP121 supports RADIUS COA standard or at least there is a way to disassociate a client through CLI command.
Thanks in advance.
-chang

Dear Chang,
Thank you for reaching the Small Business Support Community.
None of the Small Business access points support the RADIUS CoA nor have CLI access, these are all GUI configurable devices with just the RADIUS feature.
I suggest you to look for an eterprise device and inquire about this feature on the wireless support community forum;
https://supportforums.cisco.com/community/netpro/wireless-mobility
Please do not hesitate to reach me back if there is any further assistance I may help you with.
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

Similar Messages

Farm server for radius

I am trying to use a server farm to get radius authentication/authorization and would like to get some comments. I have not found any related documentation in this case or at least using the CSM.
Does the attached configuration take sense?
I appreciated.
Jose

CSM does NOT have specific support for radius LB.
The CSM can only support radius LB at L4, but there's no support for stickiness based on application-specific information.
Simple Answer: yes you can do it, but you need to tackle it at layer 4.
With loadbalancing radius, you also need to make sure that subsequent traffic should also hit the same radius server
Your config should look like
vlan 232 server
ip address 172.22.9.4 255.255.255.0
gateway 172.22.9.1
alias 172.22.9.6 255.255.255.0!!
!PROBES !
probe RADIUS-ACT-PROBE udp
interval 15
retries 2
failed 2
port 1812
probe RADIUS-AUTHE-PROBE udp
interval 15
retries 2
failed 2
port 1813
!! serverfarm !
serverfarm RADIUS
nat server
no nat client
real 172.22.1.130
inservice
probe RADIUS-ACT-PROBE
probe RADIUS-AUTHE-PROBE!!
!! Sticky configuration!
Sticky 19 netmask 255.255.255.255 address source
! Virtual servers !
vserver RADIUS-ACT
virtual 172.20.2.12 any
sticky 30 group 19
serverfarm RADIUS
inservice
Hope it helps
Syed I Ahmed

C3750V2 Support for CoA and the Overarching ISE Features

so this document lists support for some of the 3750 lines, but not all ...
http://www.cisco.com/c/en/us/td/docs/security/ise/1-2/compatibility/ise_sdt.html
What I really need to know for is, is the 3750V2 also included ?
Thanks guys !

Yes, it is not listed but it is supported. CoA was added to the 3750 family switches in version 12.2(52)SE:
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750/software/release/12-2_55_se/release/notes/OL23054.html
Thank you for rating helpful posts!

An error occurred during the installation of assembly 'Microsoft.VC80.ATL,version="8.0.50727.1833",publicKeyToken="1fc8b3b9a1e18e3b",processorArchitecture="amd64",type="win32"'. Please refer to Help and Support for more information. HRESULT: 0x80070003.

I received the above error reinstalling SQL Server 2008. I have tried all suggestions. This error also appears when I install any version of SQL Server.
I have also installed;
Microsoft® .NET Framework Version 2.0.50727.4927
Microsoft® .NET Framework Version 4.0.31106.0
Microsoft® .NET Framework Version 3.0.6920.50
Microsoft Visual C++ 2005 Redistributable (x64) 8.0.59192
Microsoft Visual C++ 2008 ATL Update kb973924 - x86 9.0.30729.4148
Microsoft Visual C++ 2008 Redistributable - x64 9.0.30729.4148
Microsoft Visual C++ 2010 x64 Redistributable 10.0.40219
Microsoft Visual C++ 2010 x86 Redistributable 10.0.40219
Microsoft Visual C++ 2012 Redistributable (x64) - 11.0.60610
Microsoft Visual C++ 2012 Redistributable (x86) - 11.0.61030
Overall summary:
Final result:                  SQL Server installation failed. To continue, investigate the reason for the failure, correct the problem, uninstall SQL Server, and then
rerun SQL Server Setup.
Exit code (Decimal):           -2068052081
Exit facility code:            1212
Exit error code:               1935
Exit message:                  SQL Server installation failed. To continue, investigate the reason for the failure, correct the problem, uninstall SQL Server, and then
rerun SQL Server Setup.
Start time:                    2014-02-23 19:17:20
End time:                      2014-02-23 19:21:35
Requested action:              Install
Log with failure:              C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20140223_191513\SqlSupport_KatmaiRTM_Cpu64_1.log
Exception help link:           http://go.microsoft.com/fwlink?LinkId=20476&ProdName=Microsoft+SQL+Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=10.50.1600.1
Machine Properties:
Machine name:                  OHPC
Machine processor count:       2
OS version:                    Windows 7
OS service pack:               Service Pack 1
OS region:                     United States
OS language:                   English (United States)
OS architecture:               x64
Process architecture:          64 Bit
OS clustered:                  No
Product features discovered:
Product              Instance             Instance ID
Feature                                  Language
Edition              Version         Clustered
Package properties:
Description:                   SQL Server Database Services 2008 R2
ProductName:                   SQL Server 2008 R2
Type:                          RTM
Version:                       10
SPLevel:                       0
Installation location:         H:\SQLServer2008R2_SP1\x64\setup\
Installation edition:          DEVELOPER
User Input Settings:
ACTION:                        Install
ADDCURRENTUSERASSQLADMIN:      False
AGTSVCACCOUNT:                 NT AUTHORITY\SYSTEM
AGTSVCPASSWORD:                *****
AGTSVCSTARTUPTYPE:             Manual
ASBACKUPDIR:                   Backup
ASCOLLATION:                   Latin1_General_CI_AS
ASCONFIGDIR:                   Config
ASDATADIR:                     Data
ASDOMAINGROUP:                 <empty>
ASLOGDIR:                      Log
ASPROVIDERMSOLAP:              1
ASSVCACCOUNT:                  <empty>
ASSVCPASSWORD:                 *****
ASSVCSTARTUPTYPE:              Automatic
ASSYSADMINACCOUNTS:            <empty>
ASTEMPDIR:                     Temp
BROWSERSVCSTARTUPTYPE:         Disabled
CONFIGURATIONFILE:             C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20140223_191513\ConfigurationFile.ini
CUSOURCE:
ENABLERANU:                    False
ENU:                           True
ERRORREPORTING:                False
FARMACCOUNT:                   <empty>
FARMADMINPORT:                 0
FARMPASSWORD:                  *****
FEATURES:                      SQLENGINE
FILESTREAMLEVEL:               0
FILESTREAMSHARENAME:           <empty>
FTSVCACCOUNT:                  <empty>
FTSVCPASSWORD:                 *****
HELP:                          False
IACCEPTSQLSERVERLICENSETERMS: False
INDICATEPROGRESS:              False
INSTALLSHAREDDIR:              C:\Program Files\Microsoft SQL Server\
INSTALLSHAREDWOWDIR:           C:\Program Files (x86)\Microsoft SQL Server\
INSTALLSQLDATADIR:             <empty>
INSTANCEDIR:                   C:\Program Files\Microsoft SQL Server\
INSTANCEID:                    MSSQLSERVER
INSTANCENAME:                  MSSQLSERVER
ISSVCACCOUNT:                  NT AUTHORITY\NetworkService
ISSVCPASSWORD:                 *****
ISSVCSTARTUPTYPE:              Automatic
NPENABLED:                     0
PASSPHRASE:                    *****
PCUSOURCE:
PID:                           *****
QUIET:                         False
QUIETSIMPLE:                   False
ROLE:                          <empty>
RSINSTALLMODE:                 FilesOnlyMode
RSSVCACCOUNT:                  <empty>
RSSVCPASSWORD:                 *****
RSSVCSTARTUPTYPE:              Automatic
SAPWD:                         *****
SECURITYMODE:                  <empty>
SQLBACKUPDIR:                  <empty>
SQLCOLLATION:                  SQL_Latin1_General_CP1_CI_AS
SQLSVCACCOUNT:                 NT AUTHORITY\SYSTEM
SQLSVCPASSWORD:                *****
SQLSVCSTARTUPTYPE:             Automatic
SQLSYSADMINACCOUNTS:           OHPC\Robert
SQLTEMPDBDIR:                  <empty>
SQLTEMPDBLOGDIR:               <empty>
SQLUSERDBDIR:                  <empty>
SQLUSERDBLOGDIR:               <empty>
SQMREPORTING:                  True
TCPENABLED:                    0
UIMODE:                        Normal
X86:                           False
Configuration file:            C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20140223_191513\ConfigurationFile.ini
Detailed results:
Feature:                       Database Engine Services
Status:                        Failed: see logs for details
MSI status:                    Passed
Configuration status:          Passed
Rules with failures:
Global rules:
Scenario specific rules:
Rules report file:               C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20140223_191513\SystemConfigurationCheck_Report.htm
SFC/ Scannow
2014-02-23 19:08:22, Info                  CSI    0000016f [SR] Verifying 100 (0x0000000000000064) components
2014-02-23 19:08:22, Info                  CSI    00000170 [SR] Beginning Verify and Repair transaction
2014-02-23 19:08:23, Info                  CSI    00000172 [SR] Cannot repair member file [l:20{10}]"wscsvc.dll" of Microsoft-Windows-SecurityCenter-Core,
Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:08:23, Info                  CSI    00000174 [SR] Cannot repair member file [l:30{15}]"amd64_installed" of Microsoft-Windows-ServicingStack,
Version = 6.1.7601.17592, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:08:26, Info                  CSI    00000176 [SR] Cannot repair member file [l:20{10}]"wscsvc.dll" of Microsoft-Windows-SecurityCenter-Core,
Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:08:26, Info                  CSI    00000177 [SR] This component was referenced by [l:242{121}]"Microsoft-Windows-Client-Features-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.Microsoft-Windows-Client-Features-Update"
2014-02-23 19:08:26, Info                  CSI    00000179 [SR] Could not reproject corrupted file [ml:520{260},l:46{23}]"\??\C:\Windows\System32"\[l:20{10}]"wscsvc.dll";
source file in store is also corrupted
2014-02-23 19:08:27, Info                  CSI    0000017c [SR] Cannot repair member file [l:30{15}]"amd64_installed" of Microsoft-Windows-ServicingStack,
Version = 6.1.7601.17592, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:08:27, Info                  CSI    0000017d [SR] This component was referenced by [l:154{77}]"Package_2_for_KB2533552~31bf3856ad364e35~amd64~~6.1.1.1.2533552-4_neutral_GDR"
2014-02-23 19:08:27, Info                  CSI    00000180 [SR] Could not reproject corrupted file [ml:520{260},l:94{47}]"\??\C:\Windows\Servicing\Version\6.1.7601.17592"\[l:30{15}]"amd64_installed";
source file in store is also corrupted
2014-02-23 19:08:27, Info                  CSI    00000182 [SR] Verify complete
2014-02-23 19:12:33, Info                  CSI    00000326 [SR] Verifying 100 (0x0000000000000064) components
2014-02-23 19:12:33, Info                  CSI    00000327 [SR] Beginning Verify and Repair transaction
2014-02-23 19:12:33, Info                  CSI    00000329 [SR] Cannot repair member file [l:26{13}]"x86_installed" of Microsoft-Windows-ServicingStack,
Version = 6.1.7601.17592, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:12:35, Info                  CSI    0000032b [SR] Cannot repair member file [l:26{13}]"x86_installed" of Microsoft-Windows-ServicingStack,
Version = 6.1.7601.17592, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:12:35, Info                  CSI    0000032c [SR] This component was referenced by [l:154{77}]"Package_2_for_KB2533552~31bf3856ad364e35~amd64~~6.1.1.1.2533552-3_neutral_GDR"
2014-02-23 19:12:35, Info                  CSI    0000032f [SR] Could not reproject corrupted file [ml:520{260},l:94{47}]"\??\C:\Windows\Servicing\Version\6.1.7601.17592"\[l:26{13}]"x86_installed";
source file in store is also corrupted
2014-02-23 19:12:36, Info                  CSI    00000331 [SR] Verify complete
2014-02-23 19:13:14, Info                  CSI    0000035d [SR] Repairing 3 components
2014-02-23 19:13:14, Info                  CSI    0000035e [SR] Beginning Verify and Repair transaction
2014-02-23 19:13:14, Info                  CSI    00000360 [SR] Cannot repair member file [l:20{10}]"wscsvc.dll" of Microsoft-Windows-SecurityCenter-Core,
Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:13:14, Info                  CSI    00000362 [SR] Cannot repair member file [l:30{15}]"amd64_installed" of Microsoft-Windows-ServicingStack,
Version = 6.1.7601.17592, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:13:14, Info                  CSI    00000364 [SR] Cannot repair member file [l:26{13}]"x86_installed" of Microsoft-Windows-ServicingStack,
Version = 6.1.7601.17592, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:13:14, Info                  CSI    00000366 [SR] Cannot repair member file [l:26{13}]"x86_installed" of Microsoft-Windows-ServicingStack,
Version = 6.1.7601.17592, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:13:14, Info                  CSI    00000367 [SR] This component was referenced by [l:154{77}]"Package_2_for_KB2533552~31bf3856ad364e35~amd64~~6.1.1.1.2533552-3_neutral_GDR"
2014-02-23 19:13:15, Info                  CSI    0000036a [SR] Could not reproject corrupted file [ml:520{260},l:94{47}]"\??\C:\Windows\Servicing\Version\6.1.7601.17592"\[l:26{13}]"x86_installed";
source file in store is also corrupted
2014-02-23 19:13:15, Info                  CSI    0000036c [SR] Cannot repair member file [l:20{10}]"wscsvc.dll" of Microsoft-Windows-SecurityCenter-Core,
Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:13:15, Info                  CSI    0000036d [SR] This component was referenced by [l:242{121}]"Microsoft-Windows-Client-Features-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.Microsoft-Windows-Client-Features-Update"
2014-02-23 19:13:15, Info                  CSI    0000036f [SR] Could not reproject corrupted file [ml:520{260},l:46{23}]"\??\C:\Windows\System32"\[l:20{10}]"wscsvc.dll";
source file in store is also corrupted
2014-02-23 19:13:15, Info                  CSI    00000371 [SR] Cannot repair member file [l:30{15}]"amd64_installed" of Microsoft-Windows-ServicingStack,
Version = 6.1.7601.17592, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch
2014-02-23 19:13:15, Info                  CSI    00000372 [SR] This component was referenced by [l:154{77}]"Package_2_for_KB2533552~31bf3856ad364e35~amd64~~6.1.1.1.2533552-4_neutral_GDR"
2014-02-23 19:13:15, Info                  CSI    00000375 [SR] Could not reproject corrupted file [ml:520{260},l:94{47}]"\??\C:\Windows\Servicing\Version\6.1.7601.17592"\[l:30{15}]"amd64_installed";
source file in store is also corrupted
2014-02-23 19:13:15, Info                  CSI    00000377 [SR] Repair complete
2014-02-23 19:13:15, Info                  CSI    00000378 [SR] Committing transaction
2014-02-23 19:13:15, Info                  CSI    0000037c [SR] Verify and Repair Transaction completed. All files and registry keys listed in this transaction
have been successfully repaired

Summary:
Attempted proposed solution. Error still appears.
This is installed:
Microsoft Visual C++ 2005 ATL Update kb973923 - x86 8.0.50727.4053
Microsoft Visual C++ 2005 Redistributable               8.0.56336
Microsoft Visual C++ 2005 Redistributable (x64)         8.0.59192
Microsoft Visual C++ 2008 ATL Update kb973924 - x86 9.0.30729.4148
Microsoft Visual C++ 2008 Redistributable - x64 9.0.30729.4148
Microsoft Visual C++ 2010 x64 Redistributable - 10.0.40219
Microsoft Visual C++ 2010 x86 Redistributable - 10.0.40219
Microsoft Visual C++ 2012 Redistributable (x64) - 11.0.60610
Microsoft Visual C++ 2012 Redistributable (x86) - 11.0.61030
I reinstalled:
vcredist_x64 Microsoft Visual C++ 2005 SP1 Redistributable Package (x64) .exe
vcredist_x86 Microsoft Visual C++ 2005 SP1 Redistributable Package (x86).exe
Results:
Windows Installer reconfigured the product. Product Name: Microsoft Visual C++ 2005 Redistributable (x64). Product Version: 8.0.56336. Product Language: 0. Manufacturer: Microsoft
Corporation. Reconfiguration success or error status: 0.
Windows Installer reconfigured the product. Product Name: Microsoft Visual C++ 2005 Redistributable. Product Version: 8.0.56336. Product Language: 0. Manufacturer: Microsoft Corporation.
Reconfiguration success or error status: 0.
I installed SQLServer2008R2_SP1
Same error message came up;
SqlSupport_KatmaiRTM_Cpu64_1.log
MSI (s) (64:94) [23:03:43:910]: Source for file 'pfbafgaq.dll' is uncompressed, at 'H:\SQLServer2008R2_SP1\1033_ENU_LP\x64\setup\sql2008support\PFiles\SqlServr\100\Setup\Release\x64\'.
MSI (s) (64:94) [23:03:43:926]: Executing op: SetTargetFolder(Folder=C:\Windows\winsxs\amd64_microsoft.vc80.atl_1fc8b3b9a1e18e3b_8.0.50727.1833_none_8a17faaf2edd3e00\)
MSI (s) (64:94) [23:03:43:926]: Executing op: SetSourceFolder(Folder=1\Windows\winsxs\nvdlei3o.taa\)
MSI (s) (64:94) [23:03:43:926]: Executing op: RegisterSharedComponentProvider(,,File=ul_ATL80.dll.837BF1EB_D770_94EB_FF1F_C8B3B9A1E18E,Component={837BF1EB-D770-94EB-A01F-
C8B3B9A1E18E},ComponentVersion=8.0.50727.1833,ProductCode={B40EE88B-400A-4266-A17B-
E3DE64E94431},ProductVersion=10.1.2731,PatchSize=0,PatchAttributes=0,PatchSequence=0,SharedComponent=0,IsFullFile=0)
MSI (s) (64:94) [23:03:43:941]: Executing op: CacheRTMFile(SourceFilePath=C:\Windows\WinSxS
\amd64_microsoft.vc80.atl_1fc8b3b9a1e18e3b_8.0.50727.762_none_ca3f79d486b08636\ATL80.dll,FileKey=ul_ATL80.dll.837BF1EB_D770_94EB_FF1F_C8B3B9A1E18E,,ProductCode={071c9b48-7c32-4621-a0ac-
3f809523288f},ProductVersion=8.0.56336,Attributes=0,,,,CopierFlags=0,,,,,,)
MSI (s) (64:94) [23:03:43:957]: Executing op: RegisterSharedComponentProvider(,,File=ul_ATL80.dll.837BF1EB_D770_94EB_FF1F_C8B3B9A1E18E,Component={837BF1EB-D770-94EB-A01F-
C8B3B9A1E18E},ComponentVersion=8.0.50727.762,ProductCode={071c9b48-7c32-4621-a0ac-
3f809523288f},ProductVersion=8.0.56336,PatchSize=0,PatchAttributes=0,PatchSequence=0,SharedComponent=0,IsFullFile=0)
MSI (s) (64:94) [23:03:43:957]: Executing op: CacheRTMFile(SourceFilePath=C:\Windows\WinSxS
\amd64_microsoft.vc80.atl_1fc8b3b9a1e18e3b_8.0.50727.762_none_ca3f79d486b08636\amd64_Microsoft.VC80.ATL_1fc8b3b9a1e18e3b_8.0.50727.1833_x-
ww_f19a562a.cat,FileKey=ul_catalog.837BF1EB_D770_94EB_FF1F_C8B3B9A1E18E,,ProductCode={071c9b48-7c32-4621-a0ac-3f809523288f},ProductVersion=8.0.56336,Attributes=0,,,,CopierFlags=0,,,,,,)
MSI (s) (64:94) [23:03:43:957]: Executing op: CacheRTMFile(SourceFilePath=C:\Windows\WinSxS
\amd64_microsoft.vc80.atl_1fc8b3b9a1e18e3b_8.0.50727.762_none_ca3f79d486b08636\amd64_Microsoft.VC80.ATL_1fc8b3b9a1e18e3b_8.0.50727.1833_x-
ww_f19a562a.manifest,FileKey=ul_manifest.837BF1EB_D770_94EB_FF1F_C8B3B9A1E18E,,ProductCode={071c9b48-7c32-4621-a0ac-
3f809523288f},ProductVersion=8.0.56336,Attributes=0,,,,CopierFlags=0,,,,,,)
MSI (s) (64:94) [23:03:43:957]: Executing op: CacheRTMFile(SourceFilePath=C:\Windows\WinSxS
\amd64_microsoft.vc80.atl_1fc8b3b9a1e18e3b_8.0.50727.762_none_ca3f79d486b08636\ATL80.dll,FileKey=ul_ATL80.dll.837BF1EB_D770_94EB_FF1F_C8B3B9A1E18E,,ProductCode={D40172D6-CE2D-4B72-BF5F-
26A04A900B7B},ProductVersion=11.0.0,Attributes=0,,,,CopierFlags=0,,,,,,)
MSI (s) (64:94) [23:03:43:957]: Executing op: RegisterSharedComponentProvider(,,File=ul_ATL80.dll.837BF1EB_D770_94EB_FF1F_C8B3B9A1E18E,Component={837BF1EB-D770-94EB-A01F-
C8B3B9A1E18E},ComponentVersion=8.0.50727.762,ProductCode={D40172D6-CE2D-4B72-BF5F-
26A04A900B7B},ProductVersion=11.0.0,PatchSize=0,PatchAttributes=0,PatchSequence=0,SharedComponent=0,IsFullFile=0)
MSI (s) (64:94) [23:03:43:972]: Executing op: CacheRTMFile(SourceFilePath=C:\Windows\WinSxS
\amd64_microsoft.vc80.atl_1fc8b3b9a1e18e3b_8.0.50727.762_none_ca3f79d486b08636\amd64_Microsoft.VC80.ATL_1fc8b3b9a1e18e3b_8.0.50727.1833_x-
ww_f19a562a.cat,FileKey=ul_catalog.837BF1EB_D770_94EB_FF1F_C8B3B9A1E18E,,ProductCode={D40172D6-CE2D-4B72-BF5F-26A04A900B7B},ProductVersion=11.0.0,Attributes=0,,,,CopierFlags=0,,,,,,)
MSI (s) (64:94) [23:03:43:972]: Executing op: CacheRTMFile(SourceFilePath=C:\Windows\WinSxS
\amd64_microsoft.vc80.atl_1fc8b3b9a1e18e3b_8.0.50727.762_none_ca3f79d486b08636\amd64_Microsoft.VC80.ATL_1fc8b3b9a1e18e3b_8.0.50727.1833_x-
ww_f19a562a.manifest,FileKey=ul_manifest.837BF1EB_D770_94EB_FF1F_C8B3B9A1E18E,,ProductCode={D40172D6-CE2D-4B72-BF5F-
26A04A900B7B},ProductVersion=11.0.0,Attributes=0,,,,CopierFlags=0,,,,,,)
MSI (s) (64:94) [23:03:43:972]: Executing op: AssemblyCopy(SourceName=uvdlei3o.taa|
ATL80.dll,SourceCabKey=ul_ATL80.dll.837BF1EB_D770_94EB_FF1F_C8B3B9A1E18E,DestName=ATL80.dll,Attributes=0,FileSize=113152,PerTick=65536,,VerifyMedia=1,ElevateFlags=4,,,,ComponentId=
{837BF1EB-D770-94EB-A01F-C8B3B9A1E18E},,,,AssemblyMode=0,)
MSI (s) (64:94) [23:03:43:972]: Assembly Error:The system cannot find the path specified.
MSI (s) (64:94) [23:03:43:972]: Note: 1: 1935 2: {837BF1EB-D770-94EB-A01F-C8B3B9A1E18E} 3: 0x80070003 4: IAssemblyCache 5: CreateAssemblyCacheItem 6:
Microsoft.VC80.ATL,version="8.0.50727.1833",publicKeyToken="1fc8b3b9a1e18e3b",processorArchitecture="amd64",type="win32"
MSI (s) (64:94) [23:03:43:972]: Assembly Error (sxs): Please look into Component Based Servicing Log located at -169675656ndir\logs\cbs\cbs.log to get more diagnostic information.
MSI (s) (64:94) [23:03:49:882]: Product: Microsoft SQL Server 2008 Setup Support Files -- Error 1935. An error occurred during the installation of assembly
'Microsoft.VC80.ATL,version="8.0.50727.1833",publicKeyToken="1fc8b3b9a1e18e3b",processorArchitecture="amd64",type="win32"'. Please refer to Help and Support for more information.
HRESULT: 0x80070003. assembly interface: IAssemblyCache, function: CreateAssemblyCacheItem, component: {837BF1EB-D770-94EB-A01F-C8B3B9A1E18E}
Error 1935. An error occurred during the installation of assembly
'Microsoft.VC80.ATL,version="8.0.50727.1833",publicKeyToken="1fc8b3b9a1e18e3b",processorArchitecture="amd64",type="win32"'. Please refer to Help and Support for more information.
HRESULT: 0x80070003. assembly interface: IAssemblyCache, function: CreateAssemblyCacheItem, component: {837BF1EB-D770-94EB-A01F-C8B3B9A1E18E}
MSI (s) (64:94) [23:03:49:882]: User policy value 'DisableRollback' is 0
Thanks, Ted U

Adobe recommends: Enhanced support for CSS3 in Dreamweaver CS5.5

Over the past week, we publicized some high-value content from adobe.com and other community sites. Hopefully you enjoyed these posts and found the resources useful. Today is our last day of the "Adobe Recommends" series.
Continuing our trip along the CSS highway, we now move to CSS3 with our next recommendation, by Preran Kurnool:
Enhanced support for CSS3 in Dreamweaver CS5.5
This blog post takes you through using box shadow, text shadow, border radius, and border image properties in Dreamweaver CS5.5.
Give it a spin and let us know what you think!
Previous recommendation threads:
Use Dreamweaver CS 5.5 to package your web application for iOS and Android devices
Customizing a Spry Menu Bar widget
Spry Menu Bar resources
Layout 101
CSS page layout basics
New CSS features in Dreamweaver CS5
Automatically attaching style sheets to new documents

Aegis Kleais wrote:
Sorry, Al, but I couldn't disagree more. Where I respect the fact that, as coders, we're rather ingrained with our workflow processes and, at times, hesitant to change, I've found LESS' benefits to be very worthwhile.
No need to apologize. Preprocessing is a topic on which there are differing opinions. You have one. I have one. There are advocates:
http://blog.urbaninsight.com/2012/04/12/ten-reasons-you-should-be-using-css-preprocessor
There are those who are not sold:
http://blog.millermedeiros.com/the-problem-with-css-pre-processors/
http://www.skybondsor.com/blog/css-preprocessors
There are those mostly sold:
http://css-tricks.com/musings-on-preprocessing/
There are even those who have been converted (but who might reverse at some later point):
http://cognition.happycog.com/article/preprocess-this
Heck, even I might be converted someday - or not
Bottom line for me, right now? I know I can write CSS that is better than most, more efficient than most, and easier to follow than most, and a preprocessor would add unwanted complexity. But that's for me. For someone not able to be organized intutively, or for a large - but carefully coordinated - team, a preprocessor could be a positive.
But not for me.
There are evolving trends - popular aspects of the technology that may and should find themselves being adapted into CSS. But I've been around this business as long as CSS has. I've seen buzzwords and trends and I've historically been spot-on in predicting the one that will stick. I think preprocessing will stick - but only insofar as it will be a catalyst for features in future versions of CSS. As a separate technology it makes no sense - to me

WLC 5500 support for Diameter protocol?

We have been having issues with wireless user authentication (sessions start/die). Multiple authentications are sometimes needed for end users to connect. We use 802.1x to Microsoft Radius in server 2008 R2, and it's flaky. I've read up on the Diameter protocol, and it looks like it would be very good to use. However, our WLC 5508's only support the normal (and very old UDP version) of Radius.
Does Cisco plan on enhancing the software to be able to support Diameter in the future?

That is something you would need to ask your Cisco SE about. I haven't heard anything regarding future support for that, but that doesn't mean it will not happen.
Mad far as your current deployment, I have many customers who are using Microsoft IAS and NPS for radius with no issues like what you are having. It's something you need to understand why they are not connecting right away. Many times it can be how the WLAN is configured or driver related issues.
-Scott

Are there plans to provide direct support for stringify capability in node-oracledb

Typically javascript binding client libraries accept stringify JSON data. It would be nice to have this capability built into the node-oracledb as well as streaming other data formats: <XML> ....
Regards,

Is this for insert or fetching of JSON? Oracle Database 12.1.0.2 can natively store JSON http://docs.oracle.com/database/121/ADXDB/json.htm
Do you want to be able to use JSON objects with Oracle bind variables?
How important is XML support for you?

RADIUS CoA Port Bounce query

Hello
I have a question relating to RADIUS CoA Port Bounce.
I'm planning to deploy 802.1x with ISE 1.3 to:
802.1x authenticate corporate desktop PCs (with anyconnect client installed for user and machine authentication) - on successful machine authentication, ISE will dynamically assign a VLAN
Profile Cisco IP phones
In order for an authenticated corporate desktop to pick up an IP address on its dynamically assigned VLAN I was thinking of using CoA Port Bounce. If this desktop was connecting through a successfully profiled Cisco IP phone, am I right in saying that the resulting Port Bounce will also affect the phone (phone will de-register from callmanager)?
Thanks
Andy

Hi Andy, if you are using PoE then a port-bounce the phone would definitely drop from the network and Call Manager. The phone would basically power down and then power back up.
Now with that being said you should keep in mind that a port-bounce would remove the existing dot1x session and will a new session would be initialized. Thus, the endpoint would end up starting at the original VLAN again and then getting the new VLAN after authorization :) So I guess what I am trying to say is that port-bounce is not the solution for this. Instead, you should consider:
1. Using dACLs instead of dynamic VLANs. That way you can have everyone in the same VLAN but use different dACLs to define network access
2. Continue to use dynamic VLANs but keep in mind that some "dumb" devices won't detect the VLAN change, thus not grabbing a new IP address. The good news is that most modern devices will detect the VLAN change and should grab a new IP. For instance, you should not have any issues with Windows 7 and newer devices
My recommendation is to go with option #1 though as that has always worked for me.
I hope this helps!
Thank you for rating helpful posts!

SBR for RADIUS Authentication

Hi Everyone,
Does anybody know if Steel Belt Radius would be able to authenticate both the telnet and enable passwords for RADIUS authentication?
I have tried IAS, but apparently IAS does not have any understanding of the enable password and therefore returns an error.
Any help would be great.
Thanks,
Dan

"enable password" authorization is not supported in RADIUS authorization. TACACS+ supports it.

RADIUS COA on software version 12.4 using 3845 router

We working to provide dynamic badwidth control by using RADIUS COA to 3845 router.
When we issue the COA 3845 rejects the message with invalid session id message.
We are using following instructions to craft RADIUS COA message.
http://www.cisco.com/en/US/docs/ios/12_4t/12_4t2/htipmaaa.html

Hi Manuel,
I have PPPOE client running directly against 3845 and terminating PPOE. Authentication, authorization and accounting work against FreeRADIUS.
Next step for us is to manage subscriber connections by sending COA to change service parameters.
Our system sends RADIUS COA as in below.
You can find the packet dumps, configuration and Cisco log below.
Thank you for responding and looking forware to your next response.
Igor
*** Example with Shaping ***
policy-map SHAPE-TEST
class class-default
shape average 48000
Using: cisco-avpair = "ip:sub-qos-policy-out=SHAPE-TEST"
======================== Packet capture =================================
No.     Time                          Source                Destination           Protocol Info
      1 2000-01-01 08:46:03.257911000 172.16.2.218          172.20.2.55           RADIUS   CoA-Request(43) (id=1, l=49)
Frame 1: 91 bytes on wire (728 bits), 91 bytes captured (728 bits)
    Arrival Time: Jan 1, 2000 08:46:03.257911000 Eastern Standard Time
    Epoch Time: 946734363.257911000 seconds
    [Time delta from previous captured frame: 0.000000000 seconds]
    [Time delta from previous displayed frame: 0.000000000 seconds]
    [Time since reference or first frame: 0.000000000 seconds]
    Frame Number: 1
    Frame Length: 91 bytes (728 bits)
    Capture Length: 91 bytes (728 bits)
    [Frame is marked: False]
    [Frame is ignored: False]
    [Protocols in frame: eth:ip:udp:radius]
    [Coloring Rule Name: UDP]
    [Coloring Rule String: udp]
Ethernet II, Src: HewlettP_af:82:b5 (2c:27:d7:af:82:b5), Dst: IntelCor_b3:18:58 (00:1b:21:b3:18:58)
    Destination: IntelCor_b3:18:58 (00:1b:21:b3:18:58)
        Address: IntelCor_b3:18:58 (00:1b:21:b3:18:58)
        .... ...0 .... .... .... .... = IG bit: Individual address (unicast)
        .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
    Source: HewlettP_af:82:b5 (2c:27:d7:af:82:b5)
        Address: HewlettP_af:82:b5 (2c:27:d7:af:82:b5)
        .... ...0 .... .... .... .... = IG bit: Individual address (unicast)
        .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
    Type: IP (0x0800)
Internet Protocol, Src: 172.16.2.218 (172.16.2.218), Dst: 172.20.2.55 (172.20.2.55)
    Version: 4
    Header length: 20 bytes
    Differentiated Services Field: 0x00 (DSCP 0x00: Default; ECN: 0x00)
        0000 00.. = Differentiated Services Codepoint: Default (0x00)
        .... ..0. = ECN-Capable Transport (ECT): 0
        .... ...0 = ECN-CE: 0
    Total Length: 77
    Identification: 0x5b26 (23334)
    Flags: 0x00
        0... .... = Reserved bit: Not set
        .0.. .... = Don't fragment: Not set
        ..0. .... = More fragments: Not set
    Fragment offset: 0
    Time to live: 128
    Protocol: UDP (17)
    Header checksum: 0x8244 [correct]
        [Good: True]
        [Bad: False]
    Source: 172.16.2.218 (172.16.2.218)
    Destination: 172.20.2.55 (172.20.2.55)
User Datagram Protocol, Src Port: 57459 (57459), Dst Port: radius-dynauth (3799)
    Source port: 57459 (57459)
    Destination port: radius-dynauth (3799)
    Length: 57
    Checksum: 0x6ec3 [validation disabled]
        [Good Checksum: False]
        [Bad Checksum: False]
Radius Protocol
    Code: CoA-Request (43)
    Packet identifier: 0x1 (1)
    Length: 49
    Authenticator: f8ce880960a402b9809f0c173c6c8530
    [The response to this request is in frame 2]
    Attribute Value Pairs
        AVP: l=10 t=Acct-Session-Id(44): 000000C3
            Acct-Session-Id: 000000C3
        AVP: l=19 t=Vendor-Specific(26) v=Cisco(9)
            VSA: l=13 t=Cisco-Policy-Down(38): POLICE-TEST
                Cisco-Policy-Down: POLICE-TEST
0000 00 1b 21 b3 18 58 2c 27 d7 af 82 b5 08 00 45 00   ..!..X,'......E.
0010 00 4d 5b 26 00 00 80 11 82 44 ac 10 02 da ac 14   .M[&.....D......
0020 02 37 e0 73 0e d7 00 39 6e c3 2b 01 00 31 f8 ce   .7.s...9n.+..1..
0030 88 09 60 a4 02 b9 80 9f 0c 17 3c 6c 85 30 2c 0a   ..`.......
0040 30 30 30 30 30 30 43 33 1a 13 00 00 00 09 26 0d   000000C3......&.
0050 50 4f 4c 49 43 45 2d 54 45 53 54                  POLICE-TEST
No.     Time                          Source                Destination           Protocol Info
      2 2000-01-01 08:46:03.259029000 172.20.2.55           172.16.2.218          RADIUS   CoA-NAK(45) (id=1, l=47)
Frame 2: 89 bytes on wire (712 bits), 89 bytes captured (712 bits)
    Arrival Time: Jan 1, 2000 08:46:03.259029000 Eastern Standard Time
    Epoch Time: 946734363.259029000 seconds
    [Time delta from previous captured frame: 0.001118000 seconds]
    [Time delta from previous displayed frame: 0.001118000 seconds]
    [Time since reference or first frame: 0.001118000 seconds]
    Frame Number: 2
    Frame Length: 89 bytes (712 bits)
    Capture Length: 89 bytes (712 bits)
    [Frame is marked: False]
    [Frame is ignored: False]
    [Protocols in frame: eth:ip:udp:radius]
    [Coloring Rule Name: UDP]
    [Coloring Rule String: udp]
Ethernet II, Src: IntelCor_b3:18:58 (00:1b:21:b3:18:58), Dst: HewlettP_af:82:b5 (2c:27:d7:af:82:b5)
    Destination: HewlettP_af:82:b5 (2c:27:d7:af:82:b5)
        Address: HewlettP_af:82:b5 (2c:27:d7:af:82:b5)
        .... ...0 .... .... .... .... = IG bit: Individual address (unicast)
        .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
    Source: IntelCor_b3:18:58 (00:1b:21:b3:18:58)
        Address: IntelCor_b3:18:58 (00:1b:21:b3:18:58)
        .... ...0 .... .... .... .... = IG bit: Individual address (unicast)
        .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default)
    Type: IP (0x0800)
Internet Protocol, Src: 172.20.2.55 (172.20.2.55), Dst: 172.16.2.218 (172.16.2.218)
    Version: 4
    Header length: 20 bytes
    Differentiated Services Field: 0x00 (DSCP 0x00: Default; ECN: 0x00)
        0000 00.. = Differentiated Services Codepoint: Default (0x00)
        .... ..0. = ECN-Capable Transport (ECT): 0
        .... ...0 = ECN-CE: 0
    Total Length: 75
    Identification: 0xe66e (58990)
    Flags: 0x00
        0... .... = Reserved bit: Not set
        .0.. .... = Don't fragment: Not set
        ..0. .... = More fragments: Not set
    Fragment offset: 0
    Time to live: 254
    Protocol: UDP (17)
    Header checksum: 0x78fd [correct]
        [Good: True]
        [Bad: False]
    Source: 172.20.2.55 (172.20.2.55)
    Destination: 172.16.2.218 (172.16.2.218)
User Datagram Protocol, Src Port: radius-dynauth (3799), Dst Port: 57459 (57459)
    Source port: radius-dynauth (3799)
    Destination port: 57459 (57459)
    Length: 55
    Checksum: 0xa044 [validation disabled]
        [Good Checksum: False]
        [Bad Checksum: False]
Radius Protocol
    Code: CoA-NAK (45)
    Packet identifier: 0x1 (1)
    Length: 47
    Authenticator: 8edb97b90c05e6ed7c1ce06688723520
    [This is a response to a request in frame 1]
    [Time from request: 0.001118000 seconds]
    Attribute Value Pairs
        AVP: l=21 t=Reply-Message(18): No Matching Session
            Reply-Message: No Matching Session
        AVP: l=6 t=Error-Cause(101): Session-Context-Not-Found(503)
            Error-Cause: Session-Context-Not-Found (503)
0000 2c 27 d7 af 82 b5 00 1b 21 b3 18 58 08 00 45 00   ,'......!..X..E.
0010 00 4b e6 6e 00 00 fe 11 78 fd ac 14 02 37 ac 10   .K.n....x....7..
0020 02 da 0e d7 e0 73 00 37 a0 44 2d 01 00 2f 8e db   .....s.7.D-../..
0030 97 b9 0c 05 e6 ed 7c 1c e0 66 88 72 35 20 12 15   ......|..f.r5 ..
0040 4e 6f 20 4d 61 74 63 68 69 6e 67 20 53 65 73 73   No Matching Sess
0050 69 6f 6e 65 06 00 00 01 f7                        ione.....
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2012.09.21 10:00:43 =~=~=~=~=~=~=~=~=~=~=~=
ABN-3845#
ABN-3845#sho run
Building configuration...
Current configuration : 2831 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname ABN-3845
boot-start-marker
boot-end-marker
enable password ipdradm
aaa new-model
aaa authentication ppp default local group radius
aaa authentication ppp mounir group radius local
aaa authorization network default local group radius
aaa authorization network mounir group radius
aaa accounting update periodic 1
--More--
aaa accounting exec mounir start-stop group radius
aaa accounting network default start-stop group radius
aaa accounting network mounir start-stop group radius
aaa server radius dynamic-author
client 172.16.2.183
client 172.20.2.234
client 172.20.2.204
client 172.16.2.218
server-key ipdradm
port 3799
auth-type session-key
aaa session-id common
dot11 syslog
ip cef
ip domain name a-bb.net
ip name-server 172.16.0.25
multilink bundle-name authenticated
--More--
vpdn-group mounir
! Default L2TP VPDN group
accept-dialin
protocol pppoe
virtual-template 11
l2tp tunnel receive-window 1024
voice-card 0
no dspfarm
--More--
archive
log config
hidekeys
policy-map POLICE-TEST
class class-default
    police 48000 9000 18000 conform-action transmit exceed-action drop violate
-action drop
bba-group pppoe global
--More--
virtual-template 11
interface Loopback0
ip address 172.29.1.5 255.255.255.255
interface GigabitEthernet0/0
ip address 172.20.2.55 255.255.255.0
duplex auto
speed auto
media-type rj45
interface GigabitEthernet0/1
ip address 10.30.1.1 255.255.255.0
duplex auto
speed auto
media-type rj45
pppoe enable group global
interface GigabitEthernet0/1.1
encapsulation dot1Q 2
interface Virtual-Template11
--More--
ip unnumbered GigabitEthernet0/1
ppp authentication pap mounir
ppp authorization mounir
ppp accounting mounir
interface Virtual-Template15
ip unnumbered Loopback0
no peer default ip address
ppp authentication pap mounir
ppp authorization mounir
ppp accounting mounir
router ospf 1
router-id 172.29.1.5
log-adjacency-changes
redistribute connected subnets
network 172.20.2.0 0.0.0.255 area 0
network 172.29.1.5 0.0.0.0 area 0
ip forward-protocol nd
no ip http server
--More--
no ip http secure-server
logging 172.20.2.150
radius-server attribute 32 include-in-access-req
radius-server attribute 32 include-in-accounting-req
radius-server attribute 25 access-request include
radius-server attribute nas-port format d
radius-server host 172.20.2.204 auth-port 1812 acct-port 1813 key ipdradm
radius-server key ipdradm
radius-server vsa send cisco-nas-port
radius-server vsa send accounting
radius-server vsa send authentication
control-plane
--More--
line con 0
line aux 0
line vty 0 4
password ipdradm
scheduler allocate 20000 1000
end
ABN-3845#
ABN-3845#
ABN-3845#
ABN-3845#debug aaa coa
AAA CoA packet processing debugging is on
ABN-3845#debug radius
Radius protocol debugging is on
Radius protocol brief debugging is off
Radius protocol verbose debugging is off
Radius packet hex dump debugging is off
Radius packet protocol debugging is on
Radius elog debugging debugging is off
Radius packet retransmission debugging is off
Radius server fail-over debugging is off
Radius elog debugging debugging is off
ABN-3845#
ABN-3845#
ABN-3845#
ABN-3845#
ABN-3845#
ABN-3845#
ABN-3845#
*Sep 21 13:59:05.380: RADIUS/ENCODE(000000BA):Orig. component type = PPoE
*Sep 21 13:59:05.380: RADIUS/ENCODE(000000BA): Acct-session-id pre-pended with N
as Port = 0/0/1/1
*Sep 21 13:59:05.380: RADIUS(000000BA): Config NAS IP: 0.0.0.0
*Sep 21 13:59:05.380: RADIUS(000000BA): Config NAS IP: 0.0.0.0
*Sep 21 13:59:05.380: RADIUS(000000BA): sending
*Sep 21 13:59:05.380: RADIUS/ENCODE: Best Local IP-Address 172.20.2.55 for Radiu
s-Server 172.20.2.204
*Sep 21 13:59:05.380: RADIUS(000000BA): Send Accounting-Request to 172.20.2.204:
1813 id 1646/40, len 322
*Sep 21 13:59:05.380: RADIUS: authenticator 65 F4 15 61 6F AD B1 76 - 45 35 D5
42 9A 3E 2F C7
*Sep 21 13:59:05.380: RADIUS: Acct-Session-Id     [44] 18 "0/0/1/1_000000C3"
*Sep 21 13:59:05.380: RADIUS: Vendor, Cisco       [26] 41
*Sep 21 13:59:05.380: RADIUS:   Cisco AVpair       [1]   35 "client-mac-address
=f8d1.11a7.167a"
*Sep 21 13:59:05.380: RADIUS: Framed-Protocol     [7]   6   PPP
       [1]
*Sep 21 13:59:05.380: RADIUS: Framed-IP-Address   [8]   6   10.30.1.2
*Sep 21 13:59:05.380: RADIUS: User-Name           [1]   9   "ipdradm"
*Sep 21 13:59:05.380: RADIUS: Vendor, Cisco       [26] 35
*Sep 21 13:59:05.380: RADIUS:   Cisco AVpair       [1]   29 "connect-progress=L
AN Ses Up"
*Sep 21 13:59:05.380: RADIUS: Vendor, Cisco       [26] 31
*Sep 21 13:59:05.380: RADIUS:   Cisco AVpair       [1]   25 "nas-tx-speed=10000
00000"
*Sep 21 13:59:05.380: RADIUS: Vendor, Cisco       [26] 31
*Sep 21 13:59:05.380: RADIUS:   Cisco AVpair       [1]   25 "nas-rx-speed=10000
00000"
*Sep 21 13:59:05.380: RADIUS: Acct-Session-Time   [46] 6   143522
*Sep 21 13:59:05.380: RADIUS: Acct-Input-Octets   [42] 6   6382156
*Sep 21 13:59:05.380: RADIUS: Acct-Output-Octets [43] 6   2559911
*Sep 21 13:59:05.380: RADIUS: Acct-Input-Packets [47] 6   224941
*Sep 21 13:59:05.380: RADIUS: Acct-Output-Packets [48] 6   161500
*Sep 21 13:59:05.380: RADIUS: Acct-Authentic      [45] 6   RADIUS
       [1]
*Sep 21 13:59:05.380: RADIUS: Acct-Status-Type    [40] 6   Watchdog
       [3]
*Sep 21 13:59:05.380: RADIUS: NAS-Port-Type       [61] 6   Ethernet
       [15]
*Sep 21 13:59:05.380: RADIUS: Vendor, Cisco       [26] 15
*Sep 21 13:59:05.380: RADIUS:   cisco-nas-port     [2]   9   "0/0/1/1"
*Sep 21 13:59:05.380: RADIUS: NAS-Port            [5]   6   16777217
*Sep 21 13:59:05.380: RADIUS: NAS-Port-Id         [87] 9   "0/0/1/1"
*Sep 21 13:59:05.380: RADIUS: Service-Type        [6]   6   Framed
       [2]
*Sep 21 13:59:05.380: RADIUS: NAS-IP-Address      [4]   6   172.20.2.55
*Sep 21 13:59:05.380: RADIUS: Unsupported         [151] 10
*Sep 21 13:59:05.380: RADIUS:   44 36 34 41 36 36 31 33
[D64A6613]
*Sep 21 13:59:05.380: RADIUS: Nas-Identifier      [32] 19 "ABN-3845.a-bb.net"
*Sep 21 13:59:05.380: RADIUS: Acct-Delay-Time     [41] 6   0
*Sep 21 13:59:09.804: RADIUS: acct-timeout for 2DC0CAF4 now 5, acct-jitter -1, a
cct-delay-time (at 2DC0CC30) now 4
ABN-3845#
ABN-3845#
*Sep 21 13:59:32.708: RADIUS: COA received from id 1 172.16.2.218:50186, CoA Re
quest, len 49
*Sep 21 13:59:32.708: COA: 172.16.2.218 request queued
*Sep 21 13:59:32.708: ++++++ CoA Attribute List ++++++
*Sep 21 13:59:32.708: 65F0A840 0 00000009 string-session-id(337) 8 000000C3
*Sep 21 13:59:32.708: 670B2A10 0 00000009 sub-policy-Out(345) 11 POLICE-TEST
*Sep 21 13:59:32.708:
*Sep 21 13:59:32.708: COA: No matching entry found
*Sep 21 13:59:32.708: COA: Added Reply Message: No Matching Session
*Sep 21 13:59:32.708: COA: Added NACK Error Cause: Session Context Not Found
*Sep 21 13:59:32.708: COA: Sending NAK from port 3799 to 172.16.2.218/50186
*Sep 21 13:59:32.708: RADIUS: 18 21 4E6F204D61746368696E672053657373696F6E
*Sep 21 13:59:32.708: RADIUS: 101 6   000001F7
ABN-3845#
ABN-3845#
ABN-3845#
ABN-3845#
ABN-3845#
ABN-3845#
ABN-3845#
ABN-3845#
===================A

Managed Provider Support for XmlType

Any idea when XmlType will be supported by the managed provider? This is the only thing preventing us from adopting it right now.
Oracle.ManagedDataAccess.Client.OracleException: Unsupported column datatype
Orign. link : Managed Provider Support for XmlType (because qustion arhived)
I am using odp.net.managed.121.1.2
It seems that still xmlType is unsupported. It there work around?

It appears you are using ODP.NET from ODAC 12c R2, which doesn't support XmlType. If you upgrade to ODP.NET in ODAC 12c R3, you will be able to use XmlType. It is currently supported in that version of managed ODP.NET.

IPod Reset Utility is not supported for use with Windows Vista??????

is there anyway to get pass this?
i need to use the ipod resetutility to reset my shuffle
but the only problem is that i have Vista and the program isnt
supported for vista. can someone help me out here?

well the only problem with that is that
everyone i know use vista -.-

Lack of support for Canon G7 and G9. Alternatives?

I am really disappointed about the lack of support for the Canon G9, and looking at the list of compatible cameras (http://docs.info.apple.com/article.html?artnum=306835) I notice that Canon G7 - even if it does not have a RAW format, is not supported either.
I am thinking that the purchase of the G9 may have been premature and that I may need to sell it and get another cam that is supported by Apple/Aperture.
What would you guys do? Is there a cam out there similar to the G9 at the moment that has a Apple-supported RAW format?
Best regards,
Kjell Are Refsvik

I think the camera closest to the G9 that has RAW support from Apple are the Panasonic DMC-LX2/Leica D-Lux 3 twins. Don't know where you are, but in the US, the Panasonic costs about $400. 10MP, 28-112mm (35mm equivalent) Leica lens, very compact body, and RAW output. The Leica costs $599, and has that classic look.
I don't know much about that cameras, but you may want to investigate.
Message was edited by: rkkwan
Message was edited by: rkkwan

Why no SyncML-support for Harmattan??

I've used SyncML on my N95 with memotoo.com for years. Worked very well. I took it for granted that SyncML would be supported on the N9. But alas, it isn't. I find that really incomprehensible. Worse yet, CalDAV syncing with memotoo doesn't work - I don't know who's to blame for this, but on the desktop it works flawelessly so I do have a suspicion. Even worse: there is no way to sync contacts using CardDAV.
MeeGo (the true MeeGo) has SyncML-support out-of-the-box. And the N9/N950 does have SyncML-support for bluetooth.
Yes, contacts syncing is supported for Ovi. And Google. And Facebook. But I do NOT want to use those services, because of grave privacy risks and because they use yet again some proprietary protocols.
I wonder, what where they thinking at Nokia for NOT supporting some well-known open standards??
(While I'm ranting: why is there ^%@$ Facebook and GTalk-support over XMPP, but no self-defined XMPP account?? Yes, you can add such accounts from the terminal, using mc-tool, but really that's just a kick in the teeth. And where's UPnP/DLNA-support?)

Hey Guys, Did you figure out any way to do PIM sync via SyncML on N9?
I am struggling to get things moving as I come from N8.
N9 just doesnt have any way to sync calendar, tasks with Ovi. Same with Notes.
Best Regards,
Suyog

ISE 1.2.1 support for Yosemite?

Hello all, just curious. I see in the release notes for ISE 1.2.X that support for Mac OS 10.10 (Yosemite) was available via patch 12 on the ISE1.2.0 train of code. That said, I see nothing in the release notes stating any support for Yosemite for any of the patches for ISE1.2.1, the latest being patch 3 released 1 week after ISE 1.2.0 patch 12. Can anyone please advise if Yosemite is in fact supported on 1.2.1 with patch 3??
Thank you very much in advance for your help
Jeff

Jeff,
OS X 10.10 is supported in ISE 1.2 p11, 1.2.1 p2 and 1.3.
Patch 12 for 1.2 and Patch 3 for 1.2.1 fix other issues for OS X 10.10, and I recommend updating to the latest patches for these fixes.
Here is the entry in the Release Notes detailing the fix for 10.10 in 1.2 p 12:
MacOsXAgent versrion 4.9.5.3 should be used and MacOsXSPWizard 1.0.0.30
Note that the description for these files denote ISE 1.2 Patch 11/12, ISE 1.3 release and above. ISE 1.2.1 is not mentioned, but follows the bug fix/release schedule for 1.2, with an adjustment.
1.2 patch 10 = 1.2.1 patch 1
Please Rate Helpful posts and mark this question as answered if, in fact, this does answer your question. Otherwise, feel free to post follow-up questions.
Charles Moreton

WAP 121 support for RADIUS COA

Similar Messages

Maybe you are looking for