WAP 321 CONFIGURAR CON IP FIJA

We have some WAP321p, we are setting an appointment with IP having no DHCP server. How do I tell him to give me DHCP at the time the client connects.

Alguen que ha realizado o sepa realizar esta configuracion?

Similar Messages

  • WAP 321 best practice

    Hi
    I've got 4 AP placed in the corners of the house.
    I would like to provide the best possibilities of roaming users which will be moved in the building.
    What kind of parameters I can change to set sensivity of reconnection user to another AP ?
    Many times I saw that device works with AP with weak signal when available is another with much stronger signal.
    Is any way to change moment when device will be reconnected ?
    Is this process related to OS of the device ?
    Generaly to avoid interference AP in neighborhood should work on different channels 1 6 11.
    To configure WDS all AP should work on the same channel. Why ?
    Is WAP 321 is salt water resist ?
    Could it be install on boat ?
    Of course inside of cabin but I can imagine that salty fog or steam available around can be dangerus.
    Please advice if I can use this model or should chose differrent ?
    Best regards
    Darek

    Hello Dariusz,
    What kind of parameters I can change to set sensivity of reconnection user to another AP ?
    Generally, the clients control which AP they want to connect at any given point of time. If you are using Windows operating system, you can set the roaming mode to aggressive where the wireless interface on the device will constantly monitor the signal strength from different Access Points in the viscinity (on the same SSID) and when it finds an AP with better signal than the current one it is attached to, it will switch the association to the new AP.
    http://www.intel.com/support/wireless/wlan/sb/cs-015906.htm
    Many times I saw that device works with AP with weak signal when available is another with much stronger signal.
    Is any way to change moment when device will be reconnected ?
    Answer is included in the link below:
    http://www.intel.com/support/wireless/wlan/sb/cs-015906.htm
    Is this process related to OS of the device ?
    This is typically controlled by the Client Operating System/wireless card driver.
    Generaly to avoid interference AP in neighborhood should work on different channels 1 6 11.
    To configure WDS all AP should work on the same channel. Why ?
    Essentially, WDS is sort of bridging/repeating across multiple Access Points without the need for a wired infrastructure to connect the access points. Since the WAP321 has a single radio interface, it cannot switch between different channels on the fly when communicating with another AP and with the clients. In order for the AP to bridge/repeat data from a neighboring access point, it has to be on the same channel as the neighboring access point and for association purposes, all other radio parameters should remain the same.
    http://en.wikipedia.org/wiki/Wireless_distribution_system
    If you have a wired infrastructure connecting these access points, then you can use Single Point Setup to connect these access points in a clusture and manage the channel assignment.
    http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=268839bea50742079bdf0ae12a245002_Single_Point_Setup_Wireless_Neighborhood_on_WAP551_and_WAP56.xml
    Hope this helps.
    Regards,
    Nagaraja

  • Cisco WAP 321 Quality Superb Worst + RMA Slow

    hi Everyone, recently i notice that the WAP 321 quality is superb worst as base on project we bought 13 units of the cisco WAP 321, out of three not even use for 1 months the unit faulty (unit cannot be power UP) but adapter power is working fine. 
    beside the quality issues, the RMA process also very slow, when we send the unit to distributor for RMA claim, the cisco feedback the unit need to wait until November of 2015, this ridiculous, how u imagine the unit faulty the replacement unit only can send it back to you almost in 9 months time. I really can't believe it, cisco is so worst on the RMA claim. 

    this is the case number, we are planning to return all the cisco ap to cisco, as our end user and us really piss off with the RMA process and quality of the cisco AP. we now waiting the feedback from the ECS which is the distributor in malaysia.

  • Problem with Workgroup Mode WAP 321

    Hello i want to setup the WorkGruop Bridge feature at the WAP 321.
    The problem is that i can´t choose the the Static WEP as Security. Does someone know the Problem?
    Regards
    Anton Fischer

    Hello Anton,
    You will not be able to configure WEP as the encryption when in the Wireless "N" mode. You can only configure WEP in "B" or "G" mode.
    Hope this helps.
    Nagaraja

  • WAP 321 new Firmware

    I see new firmware is available fo rthe WAP 321.
    I tried to read the release notes from the link in the rupper right hand side of the scren bt get a 'Forbidden file' message.    I am logged into Cisco.com .

    Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. Thank you for using the Cisco Community Post Forums.
    The release notes for the WAP321 and the WAP121 are the same. Please try this link:
    http://www.cisco.com/en/US/docs/wireless/access_point/csbap/wap121/release/notes/ReleaseNotes_for_the_WAP121_321.pdf
    I was able to get to this. I will have the other link investigated.
    Thanks
    Eric Moyers
    Cisco Network Advanced Support Engineer
    SBSC Wireless and Surveillance SME
    CCNA, CCNA-Wireless
    1-866-606-1866

  • Tengo un Apple TV trato de configurar con el airplay y no puedo

    Tengo un Apple TV trato de configurar con el airplay y no puedo

    That is the problem
    In a computer installed Firefox 5.0 es, and I have problems with Yahoo mail. I can not send emails or contacts will be the pestsña.
    I e-well and low attachments. But if I write a new mail or forward an email, does not respond when you click on the icon. Nor will the contact tab.

  • WAP 321 NPS

    Hi,
    We want to configure a Cisco WAP 321 to NPS on windows 2008.
    We have this error and we do not know what is wrong. Can you help us?.
    On NPS system event viewer :
    An Access-Request message was recived from RADIUS client XXXXXX with a Message-Authenticatior attribute that is not valid.
    We have installed other RADIUS client on Windows 2003 Server and we have the same error.
    On the Web interface of Cisco WAP only can configure the IP and password of the Radius server.
    Please, can you help us?.
    Thanks.

    Hi,
    go to your NPS/IAS, edit your RADIUS client configuration, clear the "Request messages must contain the Message-Authenticator attribute" checkbox and try again.
    regards
    Stefan

  • WAP 321 Losing connectivity

    Hi,
    I installed four WAP 321 for a customer at a remote site. They are set to use a tagged VLAN 80 for management, there three additional VLANs used for SSIDs.
    They have latest firmware installed.
    LAN setting has untagged VLAN unchecked, 'Green Ethernet' is enabled but I think I have tried disabling it.
    Connections are to trunk ports on 3560 with native VLAN 1.
    WPAs are in single-point access mode.
    All seems to work, but after a period of time, I would guess about 5-6 hours, the WAPs start losing connectivity to the wired ports, I cant ping them and there is no entry on the switchport MAC address table. Sometime I see ARP entries for both VLAN 80 and VLAN 1 (not used).
    The only way I can regain connectivity to these devices is to shut the switchports for a while (count to 20;-) then re-enable which I presume hard boots the device.
    I haven't been able to verify yet but I suspect these devices are losing all connectivity to the wired network.
    I really need a resolution for this, so any help gratefully received!
    Regards,
    Kevin.
    Sent from Cisco Technical Support iPad App

    For the sake of those that come after me .....
    My WAP 321s connected for about 40 hours now so it looks like this is resolved, this looks like a bug in the 'OS/firmware - currently version 1.0.3.4
    To summarise;
    In 'VLAN and IPv4 Address' settings your are advised to leave the Untagged VLAN Enabled, and leave the untagged (native) VLAN and Management VLAN as 1.  I haven't established if any one of these settings causes the problem, but certainly changing all three is likely to cause devices to hang within a working day.
    VLAN and IPv4 Address
    Global Settings
    MAC Address:
    D8:67:D9:C3:D5:38
    Untagged VLAN:
    Enable
    Untagged VLAN ID:
    (Range: 1 - 4094, Default: 1)
    Management VLAN ID:
    (Range: 1 - 4094, Default: 1)

  • Client cannot associate to WAP 321.

    Dear Support Team
    I have purchased, cisco wap 321 2 days back and configured it. Problems I am facing are
    1. Clients are not able to connect to it. If they get connected and get an IP address from DHCP server. They have frequent disconnection.
    2. User face high latency.
    I would like if cisco team can take remote and resolve the issue.
    Thanks
    Deepak Khemani

    Hello Deepak, first please try disabling the Bandwidth Utilization found under the wireless tab. If that does not resolve your problem the best thing would be to call in and open a case. At that point then one of our engineers can remote into your system and see what is going on.
    Eric Moyers
    .:|:.:|:. CISCO | Eric Moyers | Cisco Technical Support |
    Wireless and Surveillance Subject Matter Expert
    Please rate helpful Posts and Let others know when your Question has been answered 
    You can click my name beside the picture if you need to email me directly
    To open a case please call one of our world-wide support centers.
    http://www.cisco.com/c/en/us/support/web/tsd-cisco-small-business-support-center-contacts.html

  • Cisco WAP 321 causes network failure ?

    Hi everybody.
    I recently bought a Cisco WAP 321 for my company, but when i connect it to the network, the switch on which I connect crashes, and I lose all connectivity to the network, (internet also). i have to unplug the WAP321 and wait for a few minutes to be able to use the network again.
    I'm currently using a small 8 port switch, There are usually 3 or 4 users connected on it. When I try connecting the WAP321 on another switch, only connected to 1 computer, it seems to be working : I can access the configuration page, and make some modifications.
    Has anyone had this problem already ?
    Any idea ?
    Thanks everybody for your time !

    Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. Thank you for using the Cisco Community Post Forums.
    Could you give a little more detail about your network? What is the switch that you are connecting to? The 8 port and the other one. A network topology would be helpful as well.
    Thanks
    Eric Moyers    .:|:.:|:.
    Cisco Small Business US STAC Advanced Support Engineer
    CCNA, CCNA-Wireless
    866-606-1866 ext 601027
    Mon - Fri 09:00 - 18:00 (UTC - 05:00)
    *Please rate the Post so other will know when an answer has been found.

  • DHCP issues with Cisco WAP 321

    I have 4 Cisco WAP 321's in my office connected to our Cisco 2911 ISR for DHCP, everything is fine on the office wifi on vlan 1 but vlan 3 with the guest wifi network it fails to obtain an IP address. I have tried under each of the WAPs to make sure it wasnt just the one nearest my desk. I was on the phone yesterday with Cisco about this and we turned on debugging and watched the DHCP requests and no requests even hit the ISR (only thing I have smartnet support on). I noticed our firmware was a few versions old so updated that this morning but still have the same issues so now I am turning to you all to help me figure this out.
    Thanks
    Jake
    This topic first appeared in the Spiceworks Community

    I have 4 Cisco WAP 321's in my office connected to our Cisco 2911 ISR for DHCP, everything is fine on the office wifi on vlan 1 but vlan 3 with the guest wifi network it fails to obtain an IP address. I have tried under each of the WAPs to make sure it wasnt just the one nearest my desk. I was on the phone yesterday with Cisco about this and we turned on debugging and watched the DHCP requests and no requests even hit the ISR (only thing I have smartnet support on). I noticed our firmware was a few versions old so updated that this morning but still have the same issues so now I am turning to you all to help me figure this out.
    Thanks
    Jake
    This topic first appeared in the Spiceworks Community

  • Cisco WAP 321 found bug that causes loss of config

    I have been setting up a WAP 321 which has been unable to retain it's settings across reboots.
    What I have found is that if I leave the Timezone set to USA (Pacific) the WAP 321 can be rebooted without losing config, but as soon as I set the timezone to United Kingdom the next reboot will cause the device to take a long time to reboot and will have then gone back to factory default setings.
    To help me determine if I have a faulty unit, does any one else have one they'd be willign to set to United Kingdom timezone & reboot to see if you get the same results?

    Hi Tom,
    It seems the exact same problem, described in diferent ways.
    For me even if i configure a different management IP and after that reboot the system, the system take much time too boot and my laptop lan interface keeps goind "connected, disconnected, connected, disconnected..." until i turn off the access point off and turn it on again after about 10 seconds.
    When it boots is in factory default settings.
    When i'm configuring the access point on Safari Browser on a Mac laptop, i have no problem at all. I can change everything and reboot every time i want without losing my configurations.
    The problem is only when i'm configuring on a windows laptop with IE9 or Google Chrome.
    I will send you an e-mail with my CCOID, serial number of the access point and this description.
    Note that this is the second Cisco WAP321 that we have received with the exact same symptom. We have returned the first one and received the second one with the same problem.
    Best regards,
    Vitor Oliveira.

  • WAP-321, Captive Portal and Wi-FI repeaters

    Hi,
    So I am currently deploying a Wi-Fi Network based around Cisco WAP-321. I use the CP function with a Radius server to authentify my users. So far so good, when a user connect to one of the AP and uses his credentials, he can login and access Internet without any trouble. But I also use some Wi-Fi repeaters (Netgear WN-1000RP) to extend the range of my wireless network in places I can't install an AP. The repeaters effectively extends the range of my network, and I can connect on them without any trouble when the CP is turned off. However, when I turn on the CP, I access the login web page and enter my credentials, but no matter what, I can't login while connected on the repeater. After some research, it looks like I have to manually enter the MAC address in the MAC trough list of the AP. Except such a feature doesn't seem to exist on the WAP-321. I have tried using WDS bridge and Workgroup bridge, but without success, since I think it's only compatible with WAP-321 and WAP-121 devices.
    So I am kind of running out of ideas to make this work, and I would be very grateful if someone could help me out.
    Thanks in advance, do not hesitate to ask me for more informations if needed.

    My name Eric Moyers. I am an Engineer in the Small Business Support Center.
    I am sorry to hear that you are experiencing this issue. 
    While what I am fixing to share is not in any way a great solution, It can be utilized as a workaround.
    With the WAP321, after trying a few different scenarios that didn’t work. I simply created two vlans, leave the Untagged vlan as main vlan and changed the Management vlan to the second. I then attached the guest SSID to the Management VLAN. This allowed me to authenticate to my guest captive portal and get an IP and get out to the internet. The Main SSID still worked normally.
    Now for some caveats:
    Problem: If a wireless client knows the IP of the WAP and the username and password they could get into the WAP.
    Solution: Setup Management Access Control to an IP outside the DHCP scope for that VLAN and have a Strong Password.
    Problem: Management of the WAP321 can only be from an IP on the Management VLAN. (In my case 2)
    Solution: Setup Management Access Control to an IP outside the DHCP scope for that VLAN and have a Strong Password.
    Not the very best solution, but the only workaround I can come up with for now.
    Eric Moyers
    .:|:.:|:. CISCO | Cisco Presales Technical Support | Wireless Subject Matter Expert
    Please rate helpful Posts and Let others know when your Question has been answered.

  • WAP 321 disconnecting all associated clients

    Hi Support,
    I am a newbie technical support. Currently, I encountered a issue about WAP321 that will occasionally disconnecting all the clients(about 7 clients only) in one shot and cannot connect back at all. However, after login to the Web Gui and reboot the WAP321. It is able to connect again.
    I had upgrade the firmware to 1.0.4.2 but the problem still exists. The AP is using only WPA2-Personal.
    The environment of the AP is like this:
    Internet->Watchguard Firewall (with AP too but different SSID with the WAP321, flat vlan) ->switches and WAP321
    Is that any misconfiguration of the AP or the network environment cause this issue?
    Another problem is the time of the AP cannot be fixed. I had tried either set the time using NTP (port 123 is opened in firewall) or manually input but it will revert back to 1999 after reboot.
    Thanks in advanced!

    Hi Support,
    I am a newbie technical support. Currently, I encountered a issue about WAP321 that will occasionally disconnecting all the clients(about 7 clients only) in one shot and cannot connect back at all. However, after login to the Web Gui and reboot the WAP321. It is able to connect again.
    I had upgrade the firmware to 1.0.4.2 but the problem still exists. The AP is using only WPA2-Personal.
    The environment of the AP is like this:
    Internet->Watchguard Firewall (with AP too but different SSID with the WAP321, flat vlan) ->switches and WAP321
    Is that any misconfiguration of the AP or the network environment cause this issue?
    Another problem is the time of the AP cannot be fixed. I had tried either set the time using NTP (port 123 is opened in firewall) or manually input but it will revert back to 1999 after reboot.
    Thanks in advanced!

  • WAP 321 Management VLAN

    HI, I want to use the management VLAN254 for my 4 WAP321. but after changing the management vlan in the unit from 20 th 254 I lost contact with the unit.
    The switch I use is a Cisco 2960. Here's the config of the port :
    interface FastEthernet0/23
    switchport trunk native vlan 254
    switchport trunk allowed vlan 5,20,254,1002-1005
    switchport mode trunk
    spanning-tree portfast
    Vlan 5 and 20 are my two SSID Vlan
    I was able to connect to the unit when the management vlan was set to 20  with an IP of 192.168.254.51 but since I chaged the vlan in the unit can't connect to it, I can't even ping it from the switch ...
    Any ideas ?

    Hi Tom,
    Got it back to work by setting the native Vlan in my 2960 to vlan 20
    I also have an issue with my 2nd wireless network, vlan 20 if I don't set the untagged vlan to 20 I can't reach that network. but no problem with my wireless network with vlan 5 which is the first one. It looks like the vlan tagging only work for the first network. Is this a normal behaviour of that AP ?
    Ben

Maybe you are looking for