WAP300N upgrading and restore configuration not working...

Hi,
We've a WAP300N accespoint and for a couple of months it works well, till last day.
All connectivity going down, throughput of data slowed down, acces time increased.
For example, when someone uses his/her laptop to navigate on our server, sometimes the connection resets, or the responstime to get the folder was more than 60 seconds.
So I did reset the ap and problem was still there.
So restored it to fabric defaults and then I another issue came there: I want to restore the original configuration file.
So I navigate to management->restore, I select the .dat file and hit "restore", but sometime my browser shows me "page not found" then or sometimes it jumps to "time out".
Sometimes the bar goes to 100% and the device restarts, but nothing happens.
So then I thought, maybe there's an upgrade (our AP has firmware 1.0.00) and yes, 1.0.01.009 is released so I tried an upgrade.
Same story, different browsers, all I get is sometimes "page not found" and sometimes "time out".
Firmware is still 1.0.00...
Does anyone recognize this kind of problem and know how to solve this?
Resetting the AP to factory defaults and then trying to upgrade doesn't work either...
I used Comodo dragon, google chrome and IE as browser... all browsers results in the same story..
Hope someone could help me?
N.B.: The AP has a fixed IP, but with DHCP enabled, it gives the same problem.
Regards,
John

Hi BSAEMS. Since the firmware update was unsuccessful, this link may help you properly perform the process. Once done, I suggest that you press and hold the reset the WAP300N for another 30 seconds and try to set it up again manually without using the saved backup file. To further isolate this matter as well, you may try using a different computer.

Similar Messages

Not able to sign into Blackberry Protect. Backup and Restore function not working. "Your device isn't associated with a Blackberry ID"

Not able to sign into Blackberry Protect. Backup and Restore function not working. Message is: "Your device isn't associated with a Blackberry ID." My Blackberry Messenger and Blackberry World is working fine so I am sure its not an ID issue on the phone. I can sign into Link, Blackberry.com and Protect. I see my device in Protect but cannot send messages or view it on a map. Times out with cannot reach device message. BB Protect on Device has a swirling circle beside the on/of switch. Cannot turn off.
I have deleted Link and re-installed.
I have reset phone to default(factory) and signed in.
OS level is 10.2.1.3062
BB Link is 1.2.3.56
Solved!
Go to Solution.

I managed to figure this out myself. I had to delete the device from the Blackberry Protect website. protect.blackberry.com. I wiped my device again and signed in with my Blackberry ID. I dont know if the step of wiping was necessary as I did not try my backup with the current configuration on the device following the delete. Restore is in progress for me!

SPA122, "Restore Configuration" not working.

Hi,
I can't restore .cfg files on the Config Management menu. The "browse" button
is not active and i can't load a file. The firmware version is 1.3.1. Tested with Firefox, Opera, Google Chrome
Internet Explorer (old V6), same results. I haven't got problems with firmware upgrade or backup configuration menu.
Using Windows XP...
Thanks. (sorry for my poor english)

Well, i saved my configuration with the config manager, do one RESET with the phone (73738#). Logon on the PC with 192.168.15.1 (Yellow LAN port). And the restore configuration is active! But when i restore my .cfg file the SPA122 don't work well. The VoIP line is working but the PC connected to the yellow LAN does not work, can't get IP address (0.0.0.0).
(I reboot PC, SPA and router,same thing).
To reproduce the bug simply put the SPA in Bridge mode in Network service.
My SPA is in bridge mode and got one PC on the yellow LAN port. The SPA122 and the PC got static IP address from the ADSL router in DHCP. SPA -> 192.168.1.70 and the PC -> 192.168.1.64.

Loss of sound (Hard-reset and restore does not work)

Hi,
I loss all sounds on my iPad 2 (currently on iOS 7.04). This is the 2nd time I have had this issue (had it with an earlier iPad) and had to replace the previous one (out of warranty period). Very frustrating as it is about the same time period after purchase. Last time, it seemed like a repeated fault with the iPad and I cannot believe I have the same issue again on a different product. It is an expensive way of having to re-buy every couple of years for no other reason.
It did not happen immediately after an update i.e. it does not appear to be "update" or iOS version-related.
Anyone got any advice please? The facts are as follows (and what I have tried).
When it happened?
I was in iMovie editing a movie when all sound went from the speaker. It continued to work with earphones plugged in, but this is now intermittent. I have no sound on the speaker at all except for when I click sounds on the menu and change the level of ringer alert (which works on the speakers). This seems to tell me that it is a software problem. I have no sound on any applications or internet video or music from iTunes. I cannot survive on the earphones as they only work for a period of time and then they fail (until I take the jack out again when it works again for a period of time before the headphones fail again).
What have I tried?
a) Numerous hard resets
b) changing the side switch's position
c) changing in general settings the side switch settings from lock rotation to mute and back again (repeatedly and in reverse to see if it makes any difference)
d) resetting all settings - this made no difference
e) erase all content and settings - interestingly at the stage when it asked me if I wanted to restore from an iCloud account, it was making sounds (the keyboard clicks - which don't make a sound irrespective of the click setting currently) i.e. appeared to have resolved the issue and as soon as I restored my iCloud back-up, the sound went again.
I would be grateful for any suggestions. This post also includes a recommendation to Apple on improving its product (relating to iCloud backups) as the ultimate solution should not be paying for a replacement for a software issue (to avoid losing all my data permanently).
My musings are that:
a) it is definitively a software issue (on account that the speakers work in certain situations only)
b) it appears to be that the software is corrupted in my iCloud back up
c) it is an issue that happens regularly and is an avoidable issue/cost to Apple's customers that needs to receive higher priority in being addressed as it is built in redundancy for a significant proportion of customers. At the very least, iCloud backups should be capable of being restored in part - is there any way this could be done so we don't lose all of our notes, media etc if the final advice is to "start again". How can it be right to lose all content because of an Apple system software issue? I am pre-guessing this will be the final advice (if I don't want to pay for a replacement iPad)?
Please help me and all those others with the same avoidable software problem.
Thank you,
Peter

This is an iPad user to user forum, so you are not addressing Apple.
Try this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Check your settings. The iPads have a small switch on the right edge. It can be used as a rotation lock to keep the screen from automatically reorienting itself as you move around, but you need to have the tablet’s settings configured properly. That same switch, right above the volume buttons, can also be set to function instead as a mute button to silence certain types of audio.
If the switch is set to work as a mute button, you can change its purpose to “screen-rotation lock” by tapping the Settings icon on the home screen. On the Settings screen, tap General on the left side, and on the right side of the screen flick down to “Use Side Switch to.” Tap to select Lock Rotation or Mute to set the button’s function. Even if you set the side switch for your preferred use, you can still mute the Mini or lock the screen. Just double-click the Home button, and when the panel of apps appears along the bottom edge of the screen, flick the row from left to right with your finger. Tap the icon on the far left side of the row to either lock the iPad’s screen or mute the iPad’s alerts, notifications and sound effects. Music, podcasts and video are not muted unless you turn the volume all the way down.
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/ts1630
http://www.atreks.com/app-no-sound-on-ipad-4-%E2%80%93-what-to-do/
 Cheers, Tom

TS3694 I just updated my 4S to the new software and since I have done this it says it is searching for service. I have tried to back up and restore but not working!!

I just updated my Iphone 4S to the new software. Ever since I did the update it has been searching for cell service and I am not able to make outgoing calls or get texts. I have tried to back up and restore but it keeps giving me the error message 3002. I tried to click on the error number but there is no info about it. Could someone help?? Thanks

After I upgraded to Mavericks I was also having this message when I tried to update. There was a previous post about this problem which offered this simple solution which worked for me:
b0n0b0
Re: Recently upgraded to Maverick from SnowLeopard. Unable to get updates from App store.
Mar 15, 2014 9:05 AM (in response to Terence Devlin)
Got it! Thanx. What I did was go to my account, check that they had my new ID and Password which they did, then hit reset button. All fixed.

Component and Application Configuration not working

Dear Friends,
I want to disable the reject button in HCM Processes and Forms Webdynpro component HRASR00_PROCESS_EXECUTE and in application asr_process_execute only for some specific roles in Portal. So I tried to use the component configuration followed by the application configuration and passed this configuration id as a application parameter in the Portal, but its not working.Please find below the config steps which I did, let me know if I am missing anything.
1. Created a new Component configuration ZTEST for the Webdynpro component HRASR00_PROCESS_EXECUTE and changed the property of the Reject button to "Invisible".
2. Created a new Application configuration ZTEST1 for the Webdynpro application ASR_PROCESS_EXECUTE and included the component configuration in the application configuration.
3. Created an Application Parameter WDCONFIGURATIONID for the Webdynpro application ASR_PROCESS_EXECUTE and hard coded its value as ZTEST1(Application configuration ID) for testing purpose.
4. Tried to test the application from Portal, but didn't work. I don't think the UWL customization is required at this point as we have hardcoded the WDCONFIGURATIONID in the Webdynpro Application.
Regards,
Sapient

Hi,
We had a same issue....the work around we got was that we had to create an enhancement...we removed the standard button...and created our custom button in place of the standard button....of course...the action method for our custom button was the same as the standard button....now since it is a custom button we were able to control the visibility of it....
you can try to do it the same way....there is no coding involve in this...only removing the standard button and placing in your own button....SAP does not allow changing the properties of the standard ui elements.....just want to mention that by removing the standard button...you are not actually removing the button....it stays on the layout....but it will not show up when you run the application....but your own custom button will show up....
If you do not know the procedure of removing the standard ui...it is fairly easy...right click on the ui element under the ROOTUIELEMENTCONTAINER...and select remove element....as i said before do not worry you are not removing it completely...it stays on the layout...and if you want to put it back...just right click on it again and select "undo deletion"....that is all
once you have your custom button there...you can control it the way you want...depending on the role....
Thanks..
AS...

Backup and restore buttons not working

Hi,
Any button in my backup and restore centre with a shield next to it (for UAC) is not working. Identical to this thread:
https://social.technet.microsoft.com/Forums/windows/en-US/6a138e65-2834-41ac-bd40-c2344e20b824/backup-and-restore-panel-buttons-not-working
A fair way down that page, Lokesh replies but I don't have any of the software that he mentions in his post. Is anyone able to help?

Hi,
According to the Lokesh's reply, this problem is probably caused by 3rd plugin in Windows Explorer Shell. UAC dialog couldn't be prompt correctly.
To resolve this problem, you can try to use ShellExViewer instead to make troubleshoot, please follow the content of the link below for more details:
https://social.technet.microsoft.com/Forums/windows/en-US/5353106e-5b19-4a26-8446-72bedf40b169/rightclick-context-menu-in-desktop-appearing-slow-win-81?forum=w8itprogeneral
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

DFU and Restore does not work

Firstly, I would like to point out that I am using the latest version of iTunes.
My girlfriend gave me her phone to fix. She has tried to install iOS 7 which does not appear to have worked and she did not make a backup.
When the phone is switched on, the 'Swipe to Setup' message appears. You select a language etc and then are greeted by a message advising to connect the phone to iTunes. When you do this, iTunes basically advises that there is an issue.
I sucessfully started DFU mode and iTunes then recognised that there was a phone in recovery mode and shows the restore button.
After clicking the initial resore button, I am then offered the 'Update and Restore option which I selected.
iTunes then shows the phone being restored:
Restoring iPhone software...
Verifying iPhone Software...
Verifying iPhone Restore...
Restoring iPhone Firmware...
It then tells me it is complete and to leave the phone connected which I do. After a few minutes, iTunes detects the phone and tells me once again that there is an issue. The phone itself, as before; shows the 'Connect to iTunes' message after going through the initial setup of language etc.
Can anyone offer any advice as to what is going wrong with this?
I have tried this procedure no fewer than seven times and it is becoming quite frustrating.
Any help would be very much appreciated.

Go elsewhere. JB voids the Apple warranty and means you will get no support from Apple, including from this Apple forum.

X61t upgrade and auto-rotate not working

I just bought an x61t off trademe for $50. I've always coveted one because my old x60s was the best thinkpad I've ever owned. This one is solid and underused. I intend to upgrade to win 8 later, and add some more ram and swap in a SSD. Just use for text input and browsing.
My problems are finding a user manual/guide, finding any thinkvantage legacy upgrade and, the biggest problem is auto rotate and tablet interface buttons don't seem to be working.
Looking on Lenovo sites hasn't been helpful in finding any of this information or solutions. It may be obsolete and unavailable.
can I download button drivers from anywhere? Any other solutions you can help with are appreciated.

Hi syrahnose,
Here's your Hardware Maintenance Manual and here's a Service and Troubleshooting Guide .
You could also run TVSU and see if it comes up with anything for your tablet.
There are quite a lot of guides and manuals here .
Regards,
Dave
Edit: Windows 8 should run fine on your machine. I'm running Windows 8 on a non-tablet x61 and it runs fine.
T430u, x301, x200T, x61T, x61, x32, x41T, x40, U160, ThinkPad Tablet 1838-22R, Z500 touch, Yoga Tab 2 Windows 8.1, Yoga Tablet 3 Pro
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
If someone helped you today, pay it forward. Help Someone Else!
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Portal Upgrade and Bi iviews not working

Dear All,
Initially the portal version was nw2004s sp 12, and it has been upgraded to nw2004s sp18.Now, the BI iviews which are under the migrated content do no work for a preview as well.
It throws the following error when I preview
The initial exception that caused the request to fail was:
Error: Internal error. No esid found.
I did have a look at a relevant note : 1166422 but not to sure how to proceed with this.
Any steps that need to be performed to help resolve this issue would be appreciated.
Regards.

Hi WD4A,
We have faced the same problem after upgrading our SP Level to 14.You might have created those IVIEWS using a system other than the SAP LOCAL SYSTEM.At the time of creating IVIEWS in EP above SP-14 it supports only SAP LOCALSYSTEM.
Please check the SAP Note - 1140854.
Regards
Indranil
line removed by moderator
Edited by: Michael Nicholls on Feb 3, 2009 5:39 PM

Iphone update not successful and restore does not work

I tried to install the latest iphone update and received a message that it was unsuccessful and I had to restore my iphone. Now, restore is unsuccessful. My phone displays an image of a cable disconnected from itunes and CD. What next? I'm dead in the water.

I had the same "unknown error 2001" every time I tried to restore the iPhone. It would detect the unit immediately in "recovery mode" but fail to restore with that error.
Then I tried this:
"+Before the iPhone is detected, but whilst connected to the computer, press on the home button and keep it pressed down until a message appears to say that a phone has been detected in recovery mode, then follow the steps indicated. It may take about 30 seconds, so don't let go."+
As suggested above (thanks, you are a savior) and it worked. I also charged the unit from the AC (not usb) for a while and restarted the PC before trying the above mentioned method. Also, I connected directly to the USB port with the cable, avoiding the "hub" thingy that comes with the phone.
Thanks! and hope that helps...

WRT54GS v2.1 Firmware upgraded and wireless will not work

Hi Everyone,
I have a WRT54GS v2.1 wireless g broadband router. I updated the firmware WRT54GSv3_4.71.4.001_fw.bin since that was what the linksys website said i needed. After updating the firmware on the router, my two laptops can see the router but are not able to connect to it. If I connect through the ethernet cord, then I can get online and access the admin page of the router. I have no clue if a setting got messed up or the firmware caused it to go nuts. Please let me know if someone knows anything.
Thanks
Delta

After you upgrade the firmware you are to reset the router by pressing the reset switch in back for 30 seconds. When done, power cycle the router. Now you must reconfigure the routers wireless settings as they are all gone. Make sure the security settings on the router match your wireless settings.
Go here for help.

Upgraded and Q10 does not work

I just upgraded my Q10. When prompted to restart the phone, I hit yes. Took about 1/2 hour to access the screen but i had no functioning Hub nor did the phone work. The two strengths of the BB. I took the battery out as the phone was getting hot! Now I only have the purple BB logo. Help!

Help is here Joyness! Let's get to the bottom of your equipment concerns. I verified this is not a known issue after updating your device. Is there any physical or water damage to your phone? Have you tried removing the battery then reinserting it back to the phone?
Thank You,
MichelleL_VZW
VZW Support
Follow us on Twitter @VZWSUPPORT

Windows 10 upgrade and now wifi not working

I've upgraded to Windows 10 now my Wifi wont work. I've updated the Wifi driver and still no luck, keep getting an error saying Can't connect to this network. My laptop is a HP Pavilion 15-p261na 15.6" Laptop

Sorry I have the same problem, but i don't get the solution "ignore rebooted router"? I don't understand that, could you explain a little bit please?

I am on windows 7 and I upgraded to 10.0.2 and now it will not open. I have removed firefox completely and uploaded it again and that did not work. So my latest attempt I removed firefox 10 again and uploaded the beta version and once again nothing.

I am on windows 7 and I upgraded to the newest verison of firefox and now it will not open. I have removed firefox completely and uploaded it again and that did not work. I then made sure it could get through my firewall and that did not work. So my latest attempt I removed firefox 10 again and uploaded the beta version hoping that would do it and once again nothing. It will not open at all. Please help - is there a live chat or a number to talk to someone at Firefox?

I think when uninstalling you may also have to choose (tick) to delete the preferences and other personal data like the bookmarks, stored passwords etc. to erase completely. If you are installing afresh, please try right-clicking on the file and '''Run as administrator''' to install. And when uninstalling, please also make sure choose to delete all data and also manually delete any '''Mozilla''', '''Mozilla Firefox''' or '''Firefox''' from %appdata%, %localappdata% and %programfiles%. You can open a location by typing for eg. %appdata% in the '''Run''' box (Windows key + R). You may also have to check the '''VirtualStore''' folder in %localappdata%. Files in the VirtualStore can be problematic. I think a clean installation may help.
[https://www.mozilla.org/en-US/firefox/new/ Firefox]
[http://kb.mozillazine.org/Installation_directory Installation Folder]
[http://kb.mozillazine.org/Profile_folder Profile Folder]
Please note that using system restore would usually damage the Firefox installation.

WAP300N upgrading and restore configuration not working...

Similar Messages

Maybe you are looking for