WAP4410N & WET200-G5 Intermittency

I have an Imerge SoundServer which streams music via my home network to various zones, including our Conservatory or Sun Room. My wireless network has evolved over the years. The link from the main part of the property to the Sun Room was originally Linksys consumer kit, a WAP54G Access Point connecting to a WET54G Ethernet bridge. The signal path is not too good, and streaming errors were not unusual, especially during parties with lots of bodies around! The very time good music is essential! Hi gain aerials helped but did not fix the problem.
Next this link was upgraded to a Linksys by Cisco WAP200 and WET200-G5 combination, again with hi gain aerials. This was rock solid, no audio dropouts.
I was impressed enough with this Cisco equipment that I decided to upgrade my entire network to Cisco Small Business products, with an RVS4000 Router feeding (amongst other things) two WAP4410N Access Points (-1 is downstairs on Ch-7, -2 is upstairs on Ch-2). WAP4410N-1 also connects to the Sun Room's WET200-G5. Again, link 100% solid, no dropped bits. Signal Strength for this path on the WET Site Survey is 100% or very close to it.
Until very recently that is! Everything downstairs, except the Sun Room kit, was dismantled for major redecoration. When everything was restored, I noticed that streaming errors are happening roughly once or twice per music track. More than enough to be annoying. Well, this stimulated me to address two long-standing WET200 issues. The first is that virtually since new (2008), one of the two anntena sockets on its rear panel has been loose, and I suspect that as a result of it turning the internal connecting wire to it may be broken. This could lead to the MIMO feature not working correctly, and may explain the intermittent loss of data. Secondly, the inline power module had failed ages ago, but as my bridge is powered by PoE from a WAPPOE12, this did not actually cause me a problem, so I just ignored it. But the signal issue was the catalyst I needed to do something about this.
The original WET200 has now been RMA'd and its replacement is due to be delivered later today. Meantime, to avoid any loss of use of my audio system, I purchased yet another WET200-G5. This was connected by wire to my PC and configured in seconds by restoring the config.bin file of its predecessor. The only change I needed to make was to alter its MAC Address in the Wireless Control List of WAP4410N-1, and check that both boxes were on Channel 7. Incidentally, firmware as delivered was Cisco branded v2.0.0.5-ETSI.
I was more that a little shocked to find that streaming errors are still happening, and I have no idea why! But of more concern is that sometimes my brand new WET200 just "disappears" and cannot be accessed at all from my GUI browser. Connect it by wire, and it's fine. At other times wireless access is OK. This never, ever happened with the original bridge. Providing channel, SSID, encryption and access control settings were the same, the original bridge was always 100% accessible by wireless. Significantly it had Linksys branded FW v1.0.13-ETSI.
Tried upgrading the new box to firmware v2.0.3.2-ETSI. No change... so it's back to the factory set revision for now to eliminate this as a variable. Both the Access Point and the Bridge have Static IP's.
So in a nutshelll... the original wireless link between WAP4410N-1 and my first WET200 was 100% OK. Connection between this same AP and my replacement bridge is not. All settings are the same, same AP with its same 3 HGA7S-EU aerials, used with same model (but new) WET200-G5 fitted with the same original 2 HGA7S-EU aerials.
Can anyone suggest what is going wrong here?
Regards
Norrie

Tried both IE and latest chrome. Resetting to factory defaults before upgrading didn't help either.
I attached screenshot if i select something and press "save" nothing is saved and selection disappear.
Date: Tue, 11 Oct 2011 11:24:56 -0600
From: [email protected]
To: [email protected]
Subject: - Re: WAP4410N-G5 firmware version 2.0.4.2
Cisco Support Community
Re: WAP4410N-G5 firmware version 2.0.4.2 created by Eric Moyers in Small Business Wireless - View the full discussion
Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. Thank you for using the Cisco Community Post Forums.
At this point I do not think your device is faulty. What browser are you using when making your changes?
Thanks
Eric Moyers
Cisco Network Support Engineer
CCNA, CCNA-Wireless
1-866-606-1866
Reply to this message by going to Cisco Support Community
Start a new discussion in Small Business Wireless at Cisco Support Community

Similar Messages

WAP4410N issues with Macbooks/Apple computers

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
History:
I have 4 WAP4410N Access Points setup in a sorority house, one for each floor. The access points they had before were D-Link 2.4GHz POE APs. The reason for changing the access points was a lack of wireless coverage in the house. About 2 weeks ago I had a complaint that ALL apple computer users were only able to get to a webpage and if they tried to click a link they would get nothing, so they would have to disconnect and then reconnect to the SSID in order to get to another page. I contacted Cisco SB support and asked if they were aware of any issues with apple. The tech said yes and that I should update to 2.0.2.1 firmware, I was currently running 2.0.1.0. The tech also said that after upgrading the firmware reset the access point and reconfigure it, so I did this. I updated the firmware on all 4 APs and had one of the girls click a few links thinking that it was fixed since it worked. Well I have heard tonight that there still is an issue. I am having complaints for ALL apple computer users that after viewing 3 -5 pages/links they have to disconnect and reconnect to the SSID, then after so many more pages they have to do it all over again.
Question:
I noticed that there is another firmware update released for the WAP4410N, will this firmware (2.0.3.3) fix the issue I am having?
If so, should I upgrade the firmware and reset the AP's again and reconfigure them, or can I just update them and not re-configure them?
If not, should I change some of my settings? Any other suggestions?
Config:
Here is a brief of the config on the AP’s: (If my memory is correct)
Host Name: AP1, 2, 3, 4
Device Name: WAP4410N_AP1, 2, 3, 4
IP Settings: Static IP
IP Address: 192.168.1.2, 3, 4, 5
IPV6: Disabled
Force Lan Port Speed 100M: Disabled
Discovery (By Bonjour): Enabled
802.1X Supplicant: Disabled
Wireless Network Mode: B/G/N-Mixed
Wireless Channel: 1, 4, 8, 11
Wireless Isolation(between SSID) Disabled
Security Mode: WPA-Personal
WPA Algorithm: AES
Key Renewal: 3600
Serial #: SER141903**
Serial #: SER141900**
Serial #: SER141903**
Serial #: SER141903**
Other equipment in the setup:
ASA 5505 firewall
Cisco Small Business SD208P Switch with PoE
Thanks for the help.
Regards,
Travis

Did you try the firmware upgrade and reconfiguring the wap4410ns travis? As a rule of thumb, I always factory reset and reconfigure the device just incase there is any glitches.
Also are you running all the access points through the unmanaged switch? If so, try to take it out of the mix and plug directly into the ASA. Try to eliminate all extra pieces in the mix so you can better understand where the failure is. Your connecting wirelessly and able to browse, your getting intermittent connectivity. Also approximately how many users are connecting to the access points at one time? Try to isolate one wap4410n and a mac and test browsing with it and see what happens.

Which type of Antenna connectors does the WAP4410N have?

Hi.
I recently purchased a Linksys WAP4410N. While I was surprised how much reach I get out of this thing, I now consider maybe upgrading it with a few better antennas.
I basically just need to know if the antenna connectors are RP TNC or some other standard (like N-type), as I've read through data sheets, googled, and just couldn't find it out.
Thanks.
Regards
Markus

Hi Markus... so glad you started this thread, otherwise I would not have known the HGA7S-EU is no longer available! My present plan calls for an ethernet cable to be run in under the floor to eliminate my present WAP4410N to WET200-G5 link, and while I am doing this to run in a second cable to a new 3rd WAP4410N to improve wireless coverage into the garden. The intention was to transfer the 2xHGA7S-EU aerials from the Bridge to the new AP (both are R-SMA connectors) and buy a third (new) HGA7S-EU to complete the set.
Despite some considerable time spent on eBay and all the main UK supplier websites tonight, I cannot find any of these available for sale now. I have posted a Want It Now on eBay to see what turns up. Glad you got a solution to your situation, and many thanks for highlighting this issue for me.
Best regards
Norrie

Macbook Air 2012: intermittent, random freezes of trackpad and keyboard lasting a few seconds each

There have been a few other people to have reported this problem, but there has been no consistent solution for me on my Macbook Air 13" 2012, running 10.8.4.
What happens is this: while typing, the built-in keyboard and trackpad will suddenly lock up at the same time, randomly, intermittently, and for just a few seconds before returning to normal. This has been true through all the updates of 10.8.x since I bought the system last year.
During the freeze, one of the three behaviors occurs:
1) both keyboard and trackpad are completely unresponsive
2) both keyboard and trackpad get really slow, with high latency. Keys pressed show up much later or have to be pressed several times before registering. Trackpad is jumpy if it moves at all.
3) key gets stuck, sometimes the BACKSPACE key, which usually results in several dozen emails getting deleted or entire paragraphs, or rows and rows of the same stuck key. Pressing other keys does nothing.
I've spoken online with various other people who have the same problem and confirmed that the built-in keyboard and trackpad seem to be joined together whenever this problem strikes. You never see one freeze without the other also freezing.
Also, these commonly-recommended solutions don't work:
a) Reset PRAM. Done this many times. Does nothing.
b) Bring it in to Apple. Did this too. They replaced the keyboard and trackpad but the problem remains.
c) Clearing caches in safe mode. No improvement.
d) Removing "com.google.keystone.deamon.plist" and "com.google.keystone.agent.plist" doesn't seem to work either, even though the errors and behavior are exactly the same for me as for george.e.gonzalez in this thread: https://discussions.apple.com/message/19702976#19702976
These files do come back, though, thanks to Google Software Update. The keystone software appears to be part of Google Chrome, although I cannot confirm this.
e) I DO have Google Android File Transfer installed like one other person reported; they said uninstalling it fixed the problem. Unfortunately, that has not worked for me. Also, Android File Transfer is installed (same version 1.0.50.2266, same Mac OS 10.8.4) on an older 2008 Macbook, and it works fine, which points to something on just this Macbook Air as being the cause.
f) I don't use the Radio Silence firewall app--can't remove it.
g) I don't have the telldus device or whatever it is, so I don't have the "com.telldus.service.plist" to remove.
h) Completely clearing out /Library/LaunchAgents, /Library/LaunchDaemons, and /Library/StartupItems doesn't do anything.
i) Repairing permissions or repairing the volume does nothing.
j) Reinstalling the OS fresh does nothing.
k) I don't have an external trackpad, mouse, or keyboard for testing while the freezing happens, but the machine itself seems to be working, just not the built-in input devices, which are on the same USB bus.
l) Pressing ESC does not stop the key stuck situation, as it does for some people.
It feels to me like a hardware problem, not an OS problem, and it feels like a USB bus issue. I have noticed that when I insert USB flash drives, I get the same lock-up for a few seconds, something which my other Macs don't do.
I've also noticed various USB errors in the Console around the same time (same as george.e.gonzalez):
7/26/13 1:20:04.000 AM kernel[0]: AppleUSBMultitouchDriver::_deviceGetReport - DeviceRequest for reportID 0x0 returned with result 0xe000404f - retrying
7/26/13 1:20:05.000 AM kernel[0]: USBF: 844075.636 AppleUSBEHCI[0xffffff80157f1000]::Found a transaction which hasn't moved in 5 seconds on bus 0x1a, timing out! (Addr: 2, EP: 0)
But I'm not able to precisely correlate these errors to the pause.
Is anybody else having this problem that can shed more light on it than these other suggested repairs? This has been frustrating for quite a while, but I've had the stuck BACKSPACE key delete hundreds of emails on a webmail platform that I was unable to recover using Undo and out of the trash, and that's just no longer tolerable...
Thank you, thank you, thank you, if anyone can help me fix this!

Hi, Dan--
Nope, none of those four... I do have Dropbox but never installed it on this machine. The other three are services I've never signed up for.
I am basically using these apps up-front:
Mail.app, Safari, Notes, Terminal, maybe LibreOffice 4.0.x, maybe Sublime Text 2, Console.
And the freezes happen about twice a day, usually when I'm in Mail or Terminal, but that's because those are the ones where I'm typing the most and can see immediately when the freezes happen. It could be happening even more frequently while I'm browsing, but I might not know it because I'm merely reading what's on the screen.
This is a list from Activity Monitor of what I'm using right now, which is very typical of what I use all day:
407
XType.FontHelper
dchang
0.0
2
2.8 MB
Intel (64 bit)
278
xpcd
dchang
0.0
2
5.0 MB
Intel (64 bit)
313
WebKitPluginAgent
dchang
0.0
2
944 KB
Intel (64 bit)
250
usernoted
dchang
0.0
2
4.0 MB
Intel (64 bit)
233
UserEventAgent
dchang
0.0
3
7.6 MB
Intel (64 bit)
347
Terminal
dchang
0.0
5
51.3 MB
Intel (64 bit)
280
tccd
dchang
0.0
2
3.8 MB
Intel (64 bit)
243
talagent
dchang
0.0
2
6.2 MB
Intel (64 bit)
244
SystemUIServer
dchang
0.1
3
26.5 MB
Intel (64 bit)
4254
System Preferences
dchang
0.5
3
24.8 MB
Intel (64 bit)
995
Sublime Text 2
dchang
0.0
12
82.5 MB
Intel (64 bit)
380
ssh-agent
dchang
0.0
3
3.0 MB
Intel (64 bit)
4321
ssh
dchang
0.0
1
2.0 MB
Intel (64 bit)
4276
ssh
dchang
0.0
1
2.0 MB
Intel (64 bit)
335
ShareKitHelper
dchang
0.0
2
9.1 MB
Intel (64 bit)
429
ScopedBookmarkAgent
dchang
0.0
2
5.0 MB
Intel (64 bit)
318
Safari Web Content
dchang
2.1
23
835.4 MB
Intel (64 bit)
316
Safari
dchang
0.2
17
127.9 MB
Intel (64 bit)
3975
QuickLookSatellite-general
dchang
0.0
4
6.0 MB
Intel (64 bit)
3974
Quick Look Helper
dchang
0.0
4
6.4 MB
Intel (64 bit)
3978
QTKitServer-(3975) QuickLookSatellite-general
dchang
0.0
2
3.7 MB
Intel
319
QTKitServer-(318) Safari Web Content
dchang
0.0
5
8.2 MB
Intel
3979
QTKitMoviesValidator-(3978) QTKitServer
dchang
0.0
3
5.3 MB
Intel
359
printtool
dchang
0.0
2
5.4 MB
Intel (64 bit)
327
pbs
dchang
0.0
4
3.7 MB
Intel (64 bit)
249
pboard
dchang
0.0
1
904 KB
Intel (64 bit)
254
Notification Center
dchang
0.0
3
18.4 MB
Intel (64 bit)
676
Notes
dchang
0.0
9
47.1 MB
Intel (64 bit)
277
NetworkBrowserAgent
dchang
0.0
3
4.4 MB
Intel (64 bit)
4156
mdworker
dchang
0.0
3
11.7 MB
Intel (64 bit)
298
Mail
dchang
0.0
11
151.5 MB
Intel (64 bit)
302
lsboxd
dchang
0.0
2
3.4 MB
Intel (64 bit)
54
loginwindow
dchang
0.1
2
25.8 MB
Intel (64 bit)
3589
LibreOffice
dchang
0.2
6
105.9 MB
Intel
230
launchd
dchang
0.0
2
1.4 MB
Intel (64 bit)
469
iTunes Helper
dchang
0.0
3
3.8 MB
Intel (64 bit)
258
imagent
dchang
0.0
3
5.3 MB
Intel (64 bit)
3508
Image Capture Extension
dchang
0.0
3
9.7 MB
Intel (64 bit)
3980
helpd
dchang
0.0
2
2.0 MB
Intel (64 bit)
270
fontd
dchang
0.0
2
6.5 MB
Intel (64 bit)
322
Flash Player (Safari Internet plug-in)
dchang
1.7
21
255.7 MB
Intel (64 bit)
245
Finder
dchang
0.1
5
73.1 MB
Intel (64 bit)
242
Dock
dchang
0.0
3
43.1 MB
Intel (64 bit)
234
distnoted
dchang
0.0
4
4.1 MB
Intel (64 bit)
3550
Dashboard
dchang
0.0
8
24.5 MB
Intel (64 bit)
663
cookied
dchang
0.0
2
3.4 MB
Intel (64 bit)
499
Console
dchang
0.0
2
26.8 MB
Intel (64 bit)
326
com.apple.NotesMigratorService
dchang
0.0
2
10.9 MB
Intel (64 bit)
4328
com.apple.iCloudHelper
dchang
0.0
3
5.5 MB
Intel (64 bit)
685
com.apple.hiservices-xpcservice
dchang
0.0
2
2.5 MB
Intel (64 bit)
315
com.apple.hiservices-xpcservice
dchang
0.0
2
2.5 MB
Intel (64 bit)
279
com.apple.dock.extra
dchang
0.0
2
13.9 MB
Intel (64 bit)
320
com.apple.audio.SandboxHelper
dchang
0.0
2
2.6 MB
Intel (64 bit)
3976
com.apple.audio.SandboxHelper
dchang
0.0
2
2.6 MB
Intel (64 bit)
3977
com.apple.audio.ComponentHelper
dchang
0.0
2
2.7 MB
Intel (64 bit)
321
com.apple.audio.ComponentHelper
dchang
0.0
2
2.9 MB
Intel (64 bit)
236
cfprefsd
dchang
0.0
4
11.6 MB
Intel (64 bit)
262
CalendarAgent
dchang
0.0
6
22.5 MB
Intel (64 bit)
4318
bash
dchang
0.0
1
1.2 MB
Intel (64 bit)
4121
bash
dchang
0.0
1
1.2 MB
Intel (64 bit)
329
AppleSpell.service
dchang
0.0
2
14.8 MB
Intel (64 bit)
261
AppleIDAuthAgent
dchang
0.0
3
2.0 MB
Intel (64 bit)
4330
Activity Monitor
dchang
2.5
5
17.9 MB
Intel (64 bit)
272
accountsd
dchang
0.0
2
3.5 MB
Intel (64 bit)
At this time, the only thing generating errors in the console log is the now-famous "coreaudiod[246]: Enabled automatic stack shots because audio IO is inactive" error that is considered normal behavior...

IMac doesn't recognise the internal hard disk (intermittent)

Hi, I was wondering if anyone could give me an advice on this problem.
Background: A few days ago my iMac (20-inch MA877LL) would not boot up, it would sit on the gray screen with the wheel spinning for ever. I thought the OS might have got corrupted so I tried to re-install Snow Leopard from the CD. Installation fails with a message like 'the content of HD can not be changed'. I then went to Disk Utilities trying to repair the disk but had no luck with the repair so I decided to format the disk. I managed to get into my hard disk using the cmd R key combination at power up and backed up my essential files onto a external hard disk. I formatted/erase the hard disk (zeroed out) and tried to reinstall the Snow Leopard again. The installation failed again. Rebooted the system again and tried to re instal again but this time I got as far as the 'select the disk where you want to install Mac OS' but my Hard Disk is not listed, it's a blank list! Rebooted the maching again, tried the installation, this time it sees the hard disk but the installation fails again.
I have tried to change the boot source by hodling the 'alt' key down at power up, but I am only given the option of the CD drive with installation disk as the boot source i.e. no Har Disk. It appears that the Hard Disk is intermittently recognised and hence my problem with booting the maching when the problem started.
I am happy to purchase an internal disk to replace the existing one, but I have a feeling the actual Disk it's OK, after all I managed to access my data to back up and then format it with no problem. I just think there's a problem somewhere that intemittently doesn't recognise the Hard Disk.
Any suggestions will be much appreciated.

You need to have the hard drive replaced. The one that is currently installed has failed.

Intermittent AD Authentication failures in ISE 1.2

Starting today I was getting intermittent authentication failures in ISE. It would say that the user was not found in the selected identity store. The account is there though. At one point I ran a authetication test from the external identity source menu and I got a failure and then the next time a pass. I have no idea why this is happening. I just updated to ISE 1.2 the other day. I'm also seeing what looks like a high level of latency on both of my PSN's. Is this normal? Any ideas?
Thanks
Jef

Interesting. I have one location that is not having this problem at all. The other is having it somewhat frequently. The PSN's for each location are tied to the local AD servers. I have not had this until we started getting 300-380 PC's connecting. We are a school so we are slowly getting started. It's real random. One user will work then another time they won't. Happens with admin and user. I have notices that with this new version of ISE it is complaining that it is getting accounting updates from the NAS too often, but I have not looked into this because I just installed 1.2 about 3-4 days ago and haven't had time to look into it.
When you say Multicast to you AD...how did you check that? We do use multicast.

Feedback for forum: WAP4410N lock ups - how we fixed!

Hi All,
Our organisation struggled for the past 12 months with 6 x WAP4410N devices in our small office environment - configured as access points, same ssid, separate channels, no interference. Our errors consisted of:
1. Random lockups, up to 3 times a day - requiring reboot to fix
2. Not passing on DHCP requests - requiring reboot to fix
3. Some wireless devices unable to ever make a successful connect
Over this 12 month period we upgraded firmware, last being 2.0.5.3, applied tips from this forum, and also opened cases with Cisco - we ended up resorting to 4 reboots per day for each device to get some productivity out of these access points.
Start of this month we contacted Eric Moyers, Cisco Engineer who monitors this forum, who assisted with opening a new Cisco case. This case was escalated immediately, beta firmware provided and tested, feedback provided as still same failures. Cisco then provided the option of full refund on all 6 devices which we accepted - provided proof of purchase (original invoices). We then purchased 6 x WAP321 inconjunction with advice from Eric - slighly more expensive than the WAP4410N, however we could have gone with WAP121's.
10 days ago we implemented the WAP321's, configuration so simple, and have had absolutely 100% trouble free success - no lockups, dropouts, refusing connections and every wireless device we have successfully connects.
I hope this information can help those of you who struggle for resolution of WAP4410N issues - raising a case is easy with Cisco, testing by Cisco support quick, refund painless and deployment of WAP321s simple. My management is extrememly happy with the outcome. If you want to contact Eric you will see his regular posts here and he even lists his direct email address.
Kindest regards,
Dale Bentley

Hi,
First of all thanks to all for the help, and CJLittle...LMAO ! My car is a Scooby and a nice blue paint job ! Believe it or not they assured me all this would work.. I bought it in one package and even questioned it. Also to be fair up until then they had always been very good... shows they have no zero about 3200XP 200 fsbetc... When I went back with the power supply and told them they changed it out and let me off on the extra money it should have been.
The crashes are as follows :-
[list=1]
Locks up after random amounts of time in games, sometimes dont even get to load it up at all, other times I can play 2 hours. When the games lock up usually there is a high pitch squeal and can only get out of it by reset or power off.
I cannot install Zone Alarm Pro or Agnitum Outpost are 2 anyway (there are others) these just come up with the installer screen and hangs there, I have to go to Task Manager to close them down, unlike the lock up in games.
The cooler is the Coolermaster Jet... and the temperature is more than acceptable (right now is 44 C) so I cannot see that at all being a factor.
leds are on on the d bracket when it locks, I did not know of this function and will check it out. Thanks for that tip.[/list=1]
Question from me: would the 2700 RAM cause these lockups ? I would have thought it would just not work at all ? If this is possible then I will go and change out the RAM as tuning it down to 166 (if it is possible) does not appeal to me ! But yes it may show what the problem is.
Thanks again, will see what happens...

CRM 7.0 Unable to open/view PDF Attachments in Email (Intermittent issue)

Hi,
Unable to open an attachment (PDF format) sent from exchange server(Lotus) to SAP CRM,Actually its an intermittent issue When i try to open email in UI ,getting an error message "File is damaged and couldnot be repaired".
I understand that PDF attachment wasn't delivered(Synchronization issue between Lotus and CRM) to SAP CRM system properly by the exchange server ( Lotus ).Hence the particular attachments are not able to view/open in SAP CRM system.
Is there anyway to trace and find out root cause of the issue?
Regards,
Shan

Issue with IE version and some PDF wasn't delivered properly by lotus exchange server

After updating to windows 8.1 my wire less internet connection is getting disconnected intermittently

After updating to windows 8.1 my wire less internet connection is getting disconnected intermittently .I am unable to predict the frequency or time
period this is occurring.But now i am really struggling to use the internet.I have tried my laptop vendor support and Microsoft support both failed to provide a solution.Please help me to resolve.I have installed the Wifi driver from real tek site many times
,but that is not helping.kindly provide me the guidance.
when i searched in internet i am able to see many people are struggling with this same issue .

Hi,
You can refer to this blog, and try to roll back to the older version of network adapter driver to check the results. Other suggestions can also be used to troubleshoot your issue.
Windows 8.1 Wifi showing "limited" or "No Internet Access"
http://blogs.technet.com/b/dennis_schnell/archive/2013/08/31/windows-8-1-wifi-showing-quot-limitied-quot-or-quot-no-internet-access-quot.aspx
Meanwhile, please check with the manufacturer of your router to update the firmware.
If the issue persists, please help to collect following information for further research:
1) Enable RAS Tracing on the client.
- Over an Administrative command prompt.
- C:\> netsh ras set tracing * enabled
2) On the client enable the following log as well:
- Over an Administrative command prompt.
- C:\> netsh trace start scenario=netconnection capture=yes tracefile=c:\net.etl
3) Now, turn off Wireless adapter on the client and Turn it back ON for making it to authenticate. Once it fails to connect to the Wireless network, proceed to the next step.
4) Disable RAS Tracing on the client.
- Over an Administrative command prompt.
- C:\> netsh ras set tracing * disabled
5) On the client disable the following log as well:
- Over an Administrative command prompt.
- C:\> netsh trace stop
6) Please provide the following files:
From the Client:
a) ZIP folder of C:\Windows\Tracing
b) C:\Net.etl and C:\Net.cab
Upload these files in SkyDrive and post back the shared link.
Keep post.
Kate Li
TechNet Community Support

Classified junk mail intermittently not moving to junk folder

Hello,
I am running Thunderbird 31.3.0 and all of a sudden the junk mail (which is classified and marked) is not being moved to the junk mail folder intermittently on some of the IMAP accounts setup on Thunderbird.
Again, this problem only intermittently occurs but it seems to happen on the same couple of email accounts. The junk mail is marked and stays in the inbox but does not automatically move to the junk folder. If I unmark one in the inbox and remark it - it moves automatically. if I restart Thunderbird, all newly received junk moves as expected for a time until the problem intermittently start occurring again.

One last thing to try:
http://kb.mozillazine.org/Standard_diagnostic_-_Thunderbird

Intermittant (not constant) SQL database ShareWebDb login failed events 3760 and 2424

My Sharepoint 3.0 services that were bundled with SBS 2008 appear to be working fine. Companyweb, etc, all work w/o issue, so I don't want to take violent action, but these errors seem to be accellerating so I would love to know if there is a known
solution.
I typically receive the following (these are in reverse time order, latest at the top, just as they appear in the event log):
Error Event ID: 3760 SQL Database 'ShareWebDb' on SQL Server instance 'np:\\.\pipe\MSSQL$Microsoft##SSEE\sql\query' not found. Additional error information from SQL Server is included below. Cannot open database "ShareWebDb" requested
by the login. The login failed. Login failed for user 'NT AUTHORITY\NETWORK SERVICE'.
one second earlier:Error Event ID: 2424 The update cannot be started because the content sources cannot be accessed. Fix the errors and try the update again. Context: Application 'Search', Catalog 'index file
on the search server Search'
Information Event ID: 18456 No description, here is the Details:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider
Name="MSSQL$MICROSOFT##SSEE" />
<EventID Qualifiers="49152">18456</EventID>
<Level>0</Level>
<Task>4</Task>
<Keywords>0x90000000000000</Keywords>
<TimeCreated
SystemTime="2010-11-12T18:35:06.000Z" />
<EventRecordID>491461</EventRecordID>
<Channel>Application</Channel>
<Computer>myserver.mydomain.local</Computer>
<Security
UserID="S-1-5-20" />
</System>
<EventData>
<Data>NT AUTHORITY\NETWORK SERVICE</Data>
<Data>[CLIENT: <named pipe>]</Data>
<Binary>184800000E000000170000005000450054003300310030005C004D004900430052004F0053004F00460054002300230053005300450045000000070000006D00610073007400650072000000</Binary>
</EventData>
</Event>
Two seconds earlier
Information Event ID 17137 No description, here is the Details:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider
Name="MSSQL$MICROSOFT##SSEE" />
<EventID Qualifiers="16384">17137</EventID>
<Level>4</Level>
<Task>2</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated
SystemTime="2010-11-12T18:35:04.000Z" />
<EventRecordID>491460</EventRecordID>
<Channel>Application</Channel>
<Computer>mysever.mydomain.local</Computer>
<Security
UserID="S-1-5-20" />
</System>
<EventData>
<Data>ShareWebDb</Data>
<Binary>F14200000A000000170000005000450054003300310030005C004D004900430052004F0053004F00460054002300230053005300450045000000070000006D00610073007400650072000000</Binary>
</EventData>
</Event>
I get more 3760 errors than 2424's. However, the
2424's do seem to usually correspond to a 3760 18456 17137 occurance and the
3760 are always preceeded by 18456 17137. I was getting one or two sets a day, lately that has increased to 5 or 10.
I've done a lot of
web research on Sharepoint Errors 3760 and
2424 and I see a number of people are experiencing the the same issue. Most of what I've come across for solutions do not apply, since errors are intermittent, not chronic and my public remote URL has already been added
to BackConnectionHostNames as per:
http://blogs.technet.com/b/sbs/archive/2009/08/05/sharepoint-services-3-search-event-errors-after-an-sbs-2008-update-rollup.aspx
I installed the SQL Server Management Studio Express so I could try to track down the permissions on this database. I see the SQL server instance, MYSERVER\Microsoft##ssee, and it shows as running, but when I try to connect to it I get the following
error: "A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote
connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1)" I'm assuming that is because I don't have access permission for that internal database.
I don't see any errors in the event log related to failed logins or any errors at all from the SQL server, but there are the time matching informational entries right before the error events and lots of other 17137's and 2803's from MSSQL$Microsoft##ssee

Thank you Kevin, that does seem to match my symptoms and I have made the change suggested. Just incase that page becomes unreachable by others, here is the part of the page that applies to this:
Issue:
=========
Receive event error 3760 and 6398 on SBS 2008
Cause:
==========
Issue was caused by incorrect Auto Close option for ShareWebDb database
Solution:
==========
1. On the SBS 2008 server, click Start -> All Programs -> Microsoft SQL Server 2005, right click SQL Server Management Studio Express and choose run as administrator.
NOTE: You must run it as administrator to perform steps below.
2. In the Server Name box, type \\.\pipe\MSSQL$Microsoft##SSEE\sql\query, click connect.
3. Expand Database node and right click the ShareWebDb then choose properties.
4. Click Options in the left pane, in the right pane, please check whether the Auto Close option is set to True, if so, please change it to False.

Hyperlinks to XLS, DOC, and PDF files that are included in a .chm file work intermittently.

SUMMARY
Hyperlinks to XLS, DOC, and PDF files that are included in a
.chm file (and the Baggage Files) only work intermittently. The
only solution appears to be deleting the Temporary Internet Files.
PROBLEM
1. I place the XLS, DOC, or PDF file in the Windows
sub-directory that corresponds to the RoboHelp project sub-folder
where the topic in which I’ll place the hyperlink exists.
2. I open the help project in RoboHelp HTML.
3. I right-click on the project’s Baggage Files
sub-folder that corresponds to the Windows sub-directory in which I
placed the XLS, DOC, or PDF file (in step 1).
4. I import the XLS, DOC, or PDF file.
5. I open the topic in which I’m going to place the
hyperlink in the WYSIWYG editor.
6. I “drag and drop” the Baggage File into the
topic (in the WYSIWYG editor) to create a link to it.
7. I save the changes and then generate HTML (.chm) help.
8. I open the .chm file and click the hyperlink. The XLS,
DOC, or PDF file may or may not open.
9. When the hyperlink works correctly, for DOC and XLS files,
a “File Download – Security Warning” dialog box
appears asking, “Do you want to open or save this
file?”. The buttons that are available are
“Open”, “Save”, and “Cancel”.
These buttons work then as one would expect. (When the hyperlink
works correctly for a PDF file, it simply opens the PDF file in a
new window; there’s no prompt to save, open, or cancel.)
10. When a hyperlink does NOT work, for DOC, XLS, and PDF
files, no dialog box or other visual message is displayed. Instead,
the sound that is associated with the “Exclamation”
program event is played (the “Windows XP
Exclamation.wav” file is the WinXP default).
Other Notes:
- The hyperlinks ALWAYS work when I view a topic using the
“View Selected Item” function (Ctrl+W) in the RoboHelp
HTML project.
- Once a hyperlink stops working, it will not start working
again until I delete all the Temporary Internet Files.
- A hyperlink will stop working even if Internet Explorer
(iexplore.exe) is closed the entire time.
WORKAROUND
Through trial and error, I have discovered that if a
hyperlink stops working, I can get it to work again using the
following steps:
1. Leave the .chm file open.
2. Open Internet Explorer.
3. Click Tools>Internet Options….
4. From the “Internet Options” dialog box, select
the “General” tab.
5. Under the “Temporary Internet Files” section,
click the “Delete Files…” button.
6. From the “Delete Files” dialog box, select
“Delete all offline content” and then click
“OK”. The files are deleted and the “Delete
Files” dialog box closes.
7. Click “OK” to close the “Internet
Options” dialog box.
8. Without closing Internet Explorer and without re-starting
the .chm file, all the hyperlinks that didn’t work before
will now work.
GENERAL SYSTEM INFORMATION
- Windows XP Pro, SP2
- Internet Explorer 6.0.2900.2180
- RoboHelp X5, 5.0.2 Build 801
- HTML (.chm) help project files exist on my local machine
- HTML (.chm) help file is run from my local machine
- Project is under RoboSource version control
TEMPORARY INTERNET SETTINGS
- “Check for newer versions of stored pages” is
set to “Automatically”
- “Current location” for the Temporary Internet
files folder is set to “C:\Documents and Settings\My
Username\Local Settings\Temporary Internet Files\”
- “Amount of disk space to use” is set to
“594” MB
“View Files…”
- An XLS or DOC file will be listed here if I click its
hyperlink and then click either “Open” or
“Save” from the “File Download – Security
Warning” dialog box.
- A file will appear here even if I click “Save”
and then click “Cancel” from the subsequent “Save
As” dialog box.
- If I click “Cancel” from the “File
Download – Security Warning” dialog box, the file does
not appear in the Temporary Internet Files folder.
- When a file does appear in the Temporary Internet Files
folder, its Internet Address is displayed similar to the following:
“ms-its:C:\PrimaryProjectFolder\ProjectName.chm::/SubFolderName/FileName.xls”
“View Objects…”
Here’s a list of all the program files that appear:
- “Microsoft Office Template and Media Control”
(Last Accessed 12/13/06) (Version 12,0,6024,0)
- “Shockwave ActiveX Control” (Last Accessed
12/14/06) (Version 10,1,4,20)
- “Shockwave Flash Object” (Last Accessed
12/18/06) (Version 9,0,28,0)
- “Windows Genuine Advantage Validation Tool”
(Last Accessed 12/14/06) (Version 1,5,722,0)
- “WUWebControl Class” (Last Accessed 12/13/06)
(Version 5,8,0,2469)
Today is 12/18/06 so the only program file that is listed as
having been “Last Accessed” today is the
“Shockwave Flash Object”.
REQUEST FOR HELP
I really want to include certain PDF, DOC, and XLS files in
their native format in a .chm file. However, I need a better
solution to my problem than the one I discovered. What I really
want is to avoid the entire problem altogether.
Have anyone seen this before or have any suggestions?

You wont be able to do that. The embedded objects would appear as images only.

MacBook Pro mid-2014 Intermittent issue with sound

This occurs in an intermittent fashion : I cannot adjust volume neither with the slider at the top of the screen, nor with the volume buttons of my keyboard. In fact, there is no way I can adjust the sound. I get this image (bottom) when I try to adjust the sound using the keyboard and the slider in the top menu is maxed and greyed out.
Context:
I bought this MacBook Pro last week, as a replacement for my mid-2009 MacBook Pro. I restored a Time Machine backup.
The new computer came with Yosemite and the old one had Mavericks installed last time I made a backup, therefore the new computer was downgraded to Mavericks when I did the restore. After the Time Machine restoration was completed on the new computer, I (re)installed Yosemite.
I just brought the computer to the Apple Store; the diagnosis tools were run and no hardware problems were found. As I said this is an intermittent problem, so sometimes I restart the machine and it works normally, other times the problem occurs. (1 out of 3 reboots, i'd say...)
What do you think ? Hardware problem ? Software issue due to Mavericks being restored on top of Yosemite ?
Any others have got the same issue ?
Thanks folks,
Emile

     Reset PRAM. http://support.apple.com/kb/PH18761?viewlocale=en_US&locale=en_US
     Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
Best.

My iphone 4s has been reporting invalid sim/sim card failure intermittently for a week. tried to solve problem permanently - in mid of reset all settings my sim card failed again. help! not backed up on icloud, just itunes. don't ask. thanks!

my iphone 4s has been reporting invalid sim/sim card failure intermittently for a week. I thought it was a one/two-time thing, so had to manually eject SIM card and put back in. Today, after it happened twice in 12 hours, someone told me to reset - i thought they meant reset all settings, not network settings. while in the middle of resetting, there was an invalid SIM card again. so a few questions - which should i do first? try to manually back up from itunes (not connected to cloud - will be after tonight!), or eject SIM card? don't know if one will jeopardize the other. also, the last time i backed up was 6 days ago - have taken hundreds of pics since then - are those all lost? is there a way to essentially not reset? i thought the reset was okay because it said i'd lose no data or media. Help! thanks much!

my iphone 4s has been reporting invalid sim/sim card failure intermittently for a week. I thought it was a one/two-time thing, so had to manually eject SIM card and put back in. Today, after it happened twice in 12 hours, someone told me to reset - i thought they meant reset all settings, not network settings. while in the middle of resetting, there was an invalid SIM card again. so a few questions - which should i do first? try to manually back up from itunes (not connected to cloud - will be after tonight!), or eject SIM card? don't know if one will jeopardize the other. also, the last time i backed up was 6 days ago - have taken hundreds of pics since then - are those all lost? is there a way to essentially not reset? i thought the reset was okay because it said i'd lose no data or media. Help! thanks much!

Mid-2010 macbook pro mini display port to hdmi works only intermittently

I have a 13-inch mid-2010 MacBook Pro running OS X 10.10.2. HDMI out from mini displayport to my Dynex TV only intermittently works. The times that I have gotten it to work involves a combination of restarting the computer, unplugging the TV and plugging it back in, then plugging in the MDP adapter. Now when I plug it in, the MacBook screen flashes black like it is trying to detect the external display, but no picture on the TV. Any help would be appreciated.

Here is the console log output when I plug in the adapter:
1/31/15 10:36:47.582 PM WindowServer[443]: Received display connect changed for display 0x3f003d
1/31/15 10:36:47.582 PM WindowServer[443]: Found 1 modes for display 0x003f003d [1, 0]
1/31/15 10:36:47.594 PM WindowServer[443]: Display 0x042732c0: GL mask 0x1; bounds (0, 0)[1280 x 800], 18 modes available
Main, Active, on-line, enabled, built-in, boot, OpenGL-accel, Vendor 610, Model 9ccb, S/N 0, Unit 0, Rotation 0
UUID 0x4f159f59a71d63aefce94e26fc6d6edd, ColorSpace { 2068752606 }
1/31/15 10:36:47.594 PM WindowServer[443]: GLCompositor: GL renderer id 0x0102261a, GL mask 0x00000003, accelerator 0x0000429b, unit 0, caps QEX|MIPMAP, vram 256 MB
texture max 8192, viewport max {8192, 8192}, extensions NPOT|GLSL|FLOAT
1/31/15 10:36:47.594 PM WindowServer[443]: Display 0x003f003f: GL mask 0x4; bounds (2304, 0)[1 x 1], 1 modes available
off-line, enabled, Vendor ffffffff, Model ffffffff, S/N ffffffff, Unit 2, Rotation 0
UUID 0xffffffffffffffffffffffffffffffff
1/31/15 10:36:47.594 PM WindowServer[443]: Display 0x003f003e: GL mask 0x4; bounds (2305, 0)[1 x 1], 1 modes available
off-line, enabled, Vendor ffffffff, Model ffffffff, S/N ffffffff, Unit 2, Rotation 0
UUID 0xffffffffffffffffffffffffffffffff
1/31/15 10:36:47.594 PM WindowServer[443]: Display 0x003f003d: GL mask 0x2; bounds (2306, 0)[1 x 1], 1 modes available
off-line, enabled, Vendor ffffffff, Model ffffffff, S/N ffffffff, Unit 1, Rotation 0
UUID 0xffffffffffffffffffffffffffffffff
1/31/15 10:36:47.605 PM WindowServer[443]: Display 0x042732c0: Unit 0: Startup Mode 1280 x 800, CGSThirtytwoBitColor, Resolution 1, ioModeID 0x80002000, ioModeDepth 0x2, IOReturn 0x0
1/31/15 10:36:47.605 PM WindowServer[443]: CGXDisplaysDidReconfigure: Display added
1/31/15 10:36:47.605 PM WindowServer[443]: CGXDisplaysDidReconfigure: Display removed
1/31/15 10:36:47.608 PM WindowServer[443]: Display 0x042732c0: GL mask 0x1; bounds (0, 0)[1280 x 800], 18 modes available
Main, Active, on-line, enabled, built-in, boot, OpenGL-accel, Vendor 610, Model 9ccb, S/N 0, Unit 0, Rotation 0
UUID 0x4f159f59a71d63aefce94e26fc6d6edd, ColorSpace { 2068752606 }
1/31/15 10:36:47.608 PM WindowServer[443]: GLCompositor: GL renderer id 0x0102261a, GL mask 0x00000003, accelerator 0x0000429b, unit 0, caps QEX|MIPMAP, vram 256 MB
texture max 8192, viewport max {8192, 8192}, extensions NPOT|GLSL|FLOAT
1/31/15 10:36:47.608 PM WindowServer[443]: Display 0x003f003f: GL mask 0x4; bounds (2304, 0)[1 x 1], 1 modes available
off-line, enabled, Vendor ffffffff, Model ffffffff, S/N ffffffff, Unit 2, Rotation 0
UUID 0xffffffffffffffffffffffffffffffff
1/31/15 10:36:47.609 PM WindowServer[443]: Display 0x003f003e: GL mask 0x4; bounds (2305, 0)[1 x 1], 1 modes available
off-line, enabled, Vendor ffffffff, Model ffffffff, S/N ffffffff, Unit 2, Rotation 0
UUID 0xffffffffffffffffffffffffffffffff
1/31/15 10:36:47.609 PM WindowServer[443]: Display 0x003f003d: GL mask 0x2; bounds (2306, 0)[1 x 1], 1 modes available
off-line, enabled, Vendor ffffffff, Model ffffffff, S/N ffffffff, Unit 1, Rotation 0
UUID 0xffffffffffffffffffffffffffffffff
1/31/15 10:36:49.582 PM WindowServer[443]: **DMPROXY** (2) Found `/System/Library/CoreServices/DMProxy'. Run with arg = -discovery
1/31/15 10:36:49.605 PM WindowServer[443]: **DMPROXY** (2) Found `/System/Library/CoreServices/DMProxy'. Run with arg = -discovery
1/31/15 10:36:49.712 PM WindowServer[443]: CGXSetDisplayColorProfileAndTransfer: Display 0x042732c0: Unit 0; ColorProfile { 2068752606 }; TransferTable (256, 12)
1/31/15 10:36:49.767 PM WindowServer[443]: CGXSetDisplayColorProfileAndTransfer: Display 0x042732c0: Unit 0; ColorProfile { 2068752606 }; TransferTable (256, 12)
1/31/15 10:36:49.771 PM com.apple.AmbientDisplayAgent[313]: AMBD Agent: xpc connection became invalid during event handler
1/31/15 10:36:49.822 PM com.apple.AmbientDisplayAgent[313]: AMBD Agent: xpc connection became invalid during event handler
1/31/15 10:36:49.865 PM DMProxy[647]: AMBD Services: connection interrupted: com.apple.AmbientDisplayAgent (Connection interrupted)
1/31/15 10:36:49.875 PM WindowServer[443]: CGXSetDisplayColorProfileAndTransfer: Display 0x042732c0: Unit 0; ColorProfile { 2068752606 }; TransferTable (256, 12)
1/31/15 10:36:49.923 PM com.apple.AmbientDisplayAgent[313]: AmbientDisplayAgent started
1/31/15 10:36:49.929 PM com.apple.AmbientDisplayAgent[313]: AMBD initializing devices
1/31/15 10:36:49.940 PM com.apple.AmbientDisplayAgent[313]: AMBD Agent: xpc connection became invalid during event handler
1/31/15 10:36:49.942 PM DMProxy[648]: AMBD Services: connection interrupted: com.apple.AmbientDisplayAgent (Connection interrupted)
1/31/15 10:36:50.017 PM com.apple.AmbientDisplayAgent[313]: AmbientDisplayAgent started
1/31/15 10:36:54.946 PM DMProxy[648]: AMBD Services serviceSendMessageWithReplyAndTimeout:131: Semaphore timeout when waiting for reply to message ID 2
1/31/15 10:36:54.946 PM DMProxy[648]: AMBD Services serviceSendMessageWithReplyAndTimeout:131: Semaphore timeout when waiting for reply to message ID 1
1/31/15 10:36:54.948 PM com.apple.AmbientDisplayAgent[313]: AMBD initializing devices
1/31/15 10:36:54.960 PM WindowServer[443]: CGXSetDisplayColorProfileAndTransfer: Display 0x042732c0: Unit 0; ColorProfile { 2068752606 }; TransferTable (256, 12)
1/31/15 10:36:54.971 PM com.apple.AmbientDisplayAgent[313]: AMBD Agent: xpc connection became invalid during event handler
1/31/15 10:36:54.972 PM com.apple.AmbientDisplayAgent[313]: AMBD Agent: xpc connection became invalid during event handler

WAP4410N & WET200-G5 Intermittency

Similar Messages

Maybe you are looking for