Warning - Reverse DNS does not match SMTP Banner
I have a installed in exchange server 2013 in the Home network. Everything looks fine. But Reserve DNS was not setup properly. Reverse DNS is not matching with my domain. "Reverse
DNS does not contain the hostname" when I checked in MXToolBox.com
I have configured FQDN on port 25 to mail.xxxxx.com. I don't know what else need to configure as Iam new to exchange.
Can some give me some steps to do this?
ItsMeSri SP 2013 Foundation
Reverse DNS (aka PTR record) is something set at your ISP level, not on your Exchange server. If you have a static IP from your provider you should be able to contact them (or log into the ISP's portal) to change the reverse DNS. If you have a dynamic IP
(meaning you didn't pay extra for a static) you will be unable to set your reverse DNS.
The implication's of not having a matching reverse DNS is that many email providers will not allow you to send them email (ex. aol.com, hotmail.com). I am actually in the same boat (on a dynamic IP) but I set up my Exchange to send all my email through a
spam filter service. If you send through a reputable spam filter you should have no issues sending to any email providers (even though reverse DNS checks will still fail).
Similar Messages
-
Reverse DNS does not match SMTP Banner
Hello,
We have a client with an SLS who is configured to send mail using the ISP as relay. With this situation, the server-side mail rules (vacation notices) are not working.
So, I need to configure the server to use DNS to send mail. The client has one public static IP, in the form of client.static.isp.gr. ISP refuses to change the PTR for a single IP, so when I check the server using mxtoolbox.com, I get +Reverse DNS does not match SMTP Banner+.
In MS Exchange, you can set the "Internet e-mail name" and change the default SMTP banner.
How can I change the SMTP banner in Postfix? (in order to put the ISPs PTR for the static IP).
Regards
KostasKostas B. has been tussling with other issues ("ISP refuses to change the PTR for a single IP") and this is unrelated to the configuration of Mail itself, from what I can tell of it. He's really trying to do something that the ISP involved isn't supporting, and that's more of an administrative or ISP issue and less of a technical issue.
As for your question (and presuming your public-facing DNS forward and reverse translations are correct and your MX record is correct, details which are not yet in evidence), launch Server Admin and set your mail server host name in the mail configuration. Server Admin > select server > Mail > general > fill in your internet-facing host name. This name should matche your public DNS MX record, and your public forward and reverse DNS translations should (also) match.
And as a general rule, please don't thread-jack. That largely serves to confound and confuse the discussions. -
Forward DNS does not match reverse dns
Hi ALl
I have a fixed IP address via BT.
When I type the IP address into MxToolbox or similar i get this warning:
BT-UK-AS BTnet UK Regional network
Reverse DNS (PTR) exists and claimes to be: mail.concept-plc.com
Forward DNS for mail.concept-plc.com is: xx.xxx.xxx.xx
Should I be worried about this and if so who do i contact to do anything about it! Concept PLC seem to be a real company.
Are we sharing a fixed IP address?
Thanks for any help.
Solved!
Go to Solution.Try the BT Business forum at http://business.forums.bt.com/
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones. -
OS X 10.4.11 Server - configured name and reverse DNS do not match / DNS
Hi all,
I have looked for similar posts but all seem to have different scenarios, hoping to get an answer from someone more experienced than myself before I do anything silly.
Help much appreciated!
Scenario:
We run a 10.4.11 OS X Server on an XServe, hosted at an ISP. ISP provides all DNS services, incl. the reversed DNS entry.
I am currently only running the following services (based on the display in ServerAdmin):
AFP
Firewall
iChat
Mail
QuickTimeStreaming
Web
All others (incl. DNS) are grayed out. (As ISP instructed us not to add a DNS service on our box, that's "normal" according to my experiences with dedicated /co-location server hosting).
We never used changeip after the initial setup, meaning the server's
Current Hostname = somename.local and
DNS Hostname = mail.ourdomainname.net
So in system.log I find this re-occuring entry:
Jul 8 11:41:22 somename servermgrd: servermgr_dns: configured name and reverse DNS name do not match (somename.local != mail.ourdomainname.net), various services may not function properly - use changeip to repair and/or correct DNS
Finally, my question:
As Mail and Web services etc. are currently running OK from what I can tell,
1) do I HAVE to change this at all?
2) Would it be much better / why?
3) Could I change this using the following command
(111.11.111.1 indicating the server's IP address)
changeip 111.11.111.1 111.11.111.1 somename.local mail.ourdomainname.net
4) without running a DNS server on the machine, i.e. DNS service is not required for this to work?
5) obviously I want to be able to use Server Admin after I issue this command...
6) can I fall back easily in case this would screw it up, or is there no risk whatsoever doing this in my case?
THANK YOU so much for any help!Hi Jonas
If port 443 is already being used on the same box as KMS then it will complain and probably not start the service? I've seen this with LDAP port 636. This is when Kerio is installed on a server configured as an OD Master. Clearly the port can't be used by both servers.
It might be easier to change the port your sites are currently using to something else? Although don't do anything yet. Pose the question to Kerio Support and see what advice they offer.
Yes moving the mail to a local folder on the mail client will do it.
Is Kerio going on the same box? If its a different box (presumably different IP address?) Then what you can do is to port forward to the new server's IP address instead of disabling it. This way while you are bringing the new server on line users can still send mail right up until the time you give instructions on changing their inbound/outbound mail server details. Of course they won't be able to receive but if you time it right they may not even get an error message? Depends on what their schedules are.
If it was me I would choose IMAP every time. As the mail admin you have full control and a central location for easy backup. KMS has a built in archiving feature that makes this a simple process. This is an easier option than going round individual client machines and making sure mail held locally in POP accounts are backed up. Besides there is always someone who falls through the loop and I'm not taking into account drive failures. It makes good sense anyway as there is talk of legislation being introduced to make this a requirement for businesses who run their own mail servers. This is certainly true for certain parts of the US and what usually happens there is generally taken up in the UK and most parts of Europe.
Kerio's WebMail Client means users don't even have to have their own computer. Just as long as they have access to one that has access to the internet they can send/receive mail. No need for dedicated mail applications such as Apple Mail, Thunderbird, Entourage etc. How mail is uses remains consistent for all users.
Yes. I did this not so long ago with Leopard's built in Mail Server. I sent an e-mail defining a time when no inbound mail would be received. Disabled port forwarding for SMTP port 25 and approx 30 minutes after that another mail stating no outbound mail should be sent. Once everything was swopped over (we were changing from a G4 10.4 server to a G5 10.5 Server) port 25 was enabled, new server brought online and everyone was mailing again with no appreciable downtime.
These boxes were to have the same IP address hence the slightly different approach.
Does this help?
Tony -
Outgoing SMTP displayed in message does not match SMTP in list
I'm using OS 10.4.3 and Mail 2.0.5. In my Mail Preferences I've specified an outging server. When I try to send mail I get an error message that Mail can't send a message using the specified server. The server listed in the error message is NOT on my list (of one) and I don't get the opportunity to select another server. This is a new problem, started yesterday. Sigh. Any help greatly appreciated.
Thanks,
Tim
PowerBook G4 Mac OS X (10.4.3)Problem resolved. I read Ernie Stamp's advice in another post and it worked for me. Thanks Ernie.
-
SharePoint 2010 (SP2010 SP1+ AU CU 2011) site built with Project Web Access template shows message in yellow "Your Local Machine Time Zone does not match your current Sharepoint Regional Settings."
KB Article http://support.microsoft.com/kb/2749599/en-us suggests applying Windows and SharePoint updates, but does not points to a specific update. Also suggests to enable "Always follow
web settings" for affected users who are in different time zone than the server time zone, but it does not work either.
Manjeet SinghHi,
According to your post, my understanding is that SharePoint 2010 (SP2010 SP1+ AU CU 2011) site built with Project Web Access template shows warning "Your Local Machine Time Zone does not match your current Sharepoint Regional Settings".
Users are getting this message even after correctly specifying and changing the timezone in their Sharepoint Settings. This is a common problem across the net, but we've found a workaround
that will eliminate this problem.
Step 1: Open your Web Database in your Browser
Step 2: Click the Arrow Under the Login ID (upper right corner)
Step 3: Choose My Settings
Step 4: Click the My Regional Settings Link
Step 5: Uncheck the 'Always Follow Web Settings' check and specify your time zone.
Step 6: Click OK
For more information, you can refer to:
Warning Message about time zone difference between your computer and the regional settings
of Sha...
Thanks & Regards,
Jason Guo
Jason Guo
TechNet Community Support -
Good afternoon!
We just completed our Exchange 2007 implementation (migration from Exchange 2003... a fun romp of 24 straight hours for the final push) and noticed an error that only occurs on Outlook 2007 clients connecting to the Exchange 2007 server: "Name on the Security Certificate is Invalid or Does Not Match the Name on the Certificate".
Now, I've done my reading into this and have determined that due to how Outlook 2007 clients managed their OAB, it is essentially through a web virtual directory now, no longer through Public Folders and this is essentially the base of our issue. See, our mail server has an internal FQDN of mail.ourdomain-domain.com whereas it has an external FQDN (which is what the SSL Cert is tied to) of owa.ourdomain.com.
So, essentially what I'm seeing is our internal Outlook 2007 clients (limited to I.S. employees only right now, thankfully) are seeing this SSL error because Outlook 2007 is trying to pick up the OAB using the internal FQDN instead of the external FQDN (which would work as well, due to some internal DNS trickery we have configured).
My question is (finally), is there a way to circumvent this internally so we never see this SSL error prompt or a way to force Outlook 2007 to use the external FQDN? I have made sure all the settings in Exchange Management Console for OAB and the like have both the internal and external FQDN set to owa.ourdomain.com (the valid SSL name), but it does not appear to have made a difference. Granted, I have not rebooted... but I do not think that is necessary in this instance.
Any suggestions would be appreciated. Thanks!!Hi All,
1) I am using Windows SBS Server 2008 with Exchange 2007 installed on it. With all the Certicate configured internally. We haven’t purchased the Certificate from any outside authority yet.
2) Also, user were getting Error message "The name on the security certificate is invalid or does not match the name of the site" in outlook, to resolve this issue I followed the steps mention on "http://support.microsoft.com/kb/940726" & “http://social.technet.microsoft.com/Forums/en-US/exchangesvrclients/thread/697f79e2-ca8f-4a2e-bae5-55d3fa7f703f/?prof=required” however I was able run only first command as I was unable to find "EWS (Default Web Site)", "oab (Default Web Site)", "unifiedmessaging (Default Web Site)".
3) After reaserching, I run following commands to get the status, location of WebServicesVirtualDirectory, OABVirtualDirectory & UMVirtualDirectory
[PS] C:\Windows\System32>Get-WebServicesVirtualDirectory | fl
Name : EWS (SBS Web Applications)
Server : PASVR01
InternalUrl : https://sites/EWS/Exchange.asmx
ExternalUrl :
[PS] C:\Windows\System32>Get-OABVirtualDirectory | fl
Name : OAB (SBS Web Applications)
Server : PASVR01
InternalUrl : https://sites/OAB
ExternalUrl :
[PS] C:\Windows\System32>Get-UMVirtualDirectory | fl
Name : UnifiedMessaging (SBS Web Applications)
Server : PASVR01
InternalUrl : https://sites/UnifiedMessaging/Service.asmx
ExternalUrl :
4) Then after getting the correct locations of all the directory I run the following commands to change the internal url on existing Certs
Set-ClientAccessServer -Identity PASVR01 -AutodiscoverServiceInternalUri https://pasvr01/owa/autodiscover/autodiscover.xml
Set-WebServicesVirtualDirectory -Identity "PASVR01\EWS (SBS Web Applications)" -InternalUrl https://pasvr01/owa/ews/exchange.asmx
Set-OABVirtualDirectory -Identity "PASVR01\OAB (SBS Web Applications)" -InternalUrl https://pasvr01/owa/oab
Set-UMVirtualDirectory -Identity "PASVR01\UnifiedMessaging (SBS Web Applications)" -InternalUrl https://pasvr01/owa/unifiedmessaging/service.asmx
5) However, this does'nt resolved our issue so run the following commands to change the external url on existing Certs
Set-WebServicesVirtualDirectory -Identity "PASVR01\EWS (SBS Web Applications)" -ExternalUrl https://exchange.domain.com/owa/ews/exchange.asmx
Set-OABVirtualDirectory -Identity "PASVR01\OAB (SBS Web Applications)" -ExternalUrl https://exchange.domain.com/owa/oab
Set-UMVirtualDirectory -Identity "PASVR01\UnifiedMessaging (SBS Web Applications)" -ExternalUrl https://exchange.domain.com/owa/unifiedmessaging/service.asmx
6) I also tried running "New-ExchangeCertificate -PrivateKeyExportable $True -Services “IMAP, POP, IIS, SMTP” -SubjectName “cn=PASVR01" as I have deleted one of the certicate on this server in past.
7) Following was the status of internal and external URL.
[PS] C:\Windows\System32>Get-WebServicesVirtualDirectory | fl
Name : EWS (SBS Web Applications)
Server : PASVR01
InternalUrl : https://pasvr01/owa/ews/exchange.asmx
ExternalUrl : https://exchange. exchange.domain.com /owa/ews/exchange.asmx
[PS] C:\Windows\System32>Get-OABVirtualDirectory | fl
Name : OAB (SBS Web Applications)
Server : PASVR01
InternalUrl : https://pasvr01/owa/oab
ExternalUrl : https://exchange. exchange.domain.com/owa/oab
[PS] C:\Windows\System32>Get-UMVirtualDirectory | fl
Name : UnifiedMessaging (SBS Web Applications)
Server : PASVR01
InternalUrl : https://pasvr01/owa/unifiedmessaging/service.asmx
ExternalUrl : https://exchange. exchange.domain.com/owa/unifiedmessaging/service.asmx
10) Still we are facing this issue of "The name on the security certificate is invalid or does not match the name of the site" in outlook.
PLEASE HELP ME TO RESOLVE THIS ISSUE.
Thanks in Advance,
Asif -
Server name SSL does not match subject of certificate Server-Cert
Sun Java System Web Server 7.0U1 B06/12/2007 22:13
We see the following warning in the startup log everytime. We have been ignoring this for awhile now since SSL is working fine and browsers don't complain. But recently we found some mobile browsers are not happy with our SSL pages. So we are thinking this may be the casue.
warning ( 3256): CORE1251: On HTTP listener http-listener-2, server name SSL does not match subject "www.ourdomain.com" of certificate Server-Cert.
What does this warning really mean? Do we need to rename the server name "SSL" to match the domain name?
ThanksAFAIK That warning is a result of the fact that the hostname doesn't match the certificate.
The cert has a Common Name (CN) attribute of the certificate's Subject Name or Subject Alternative Name (SAN) of type DNS name
should match with the server's DNS name.
hostname == machines name
I don't know if we need to change the instances server name as well.
I will try on my machine and and will let you know.
Are you sure this warning is the source of your problem? Look at what Joe has written :
"If most of your users are not getting browsers complaining of a mis-match then this is likely not the source of your mobile device problem."
Which mobile model and browsers are you getting complains from? We can try testing it here. -
[Solved] (WW) fglrx(0): Kernel Module version does *not* match driver.
fglrx has just recently stopped working, and I can't quite pinpoint when that was because I honestly hadn't noticed until checking. I've tried a few reinstalls and different xorg options so far, but had no luck.
glxinfo:
name of display: :0.0
display: :0 screen: 0
direct rendering: No
server glx vendor string: SGI
server glx version string: 1.2
server glx extensions:
GLX_ARB_multisample, GLX_EXT_visual_info, GLX_EXT_visual_rating,
GLX_EXT_import_context, GLX_EXT_texture_from_pixmap, GLX_OML_swap_method,
GLX_SGI_make_current_read, GLX_SGIS_multisample, GLX_SGIX_hyperpipe,
GLX_SGIX_swap_barrier, GLX_SGIX_fbconfig, GLX_MESA_copy_sub_buffer
client glx vendor string: ATI
client glx version string: 1.3
client glx extensions:
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_EXT_import_context,
GLX_ARB_get_proc_address, GLX_SGI_video_sync, GLX_ARB_multisample,
GLX_ATI_pixel_format_float, GLX_ATI_render_texture
GLX version: 1.2
GLX extensions:
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_EXT_import_context,
GLX_ARB_multisample
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.4 (1.5 Mesa 6.5.2)
OpenGL extensions:
GL_ARB_imaging, GL_ARB_multitexture, GL_ARB_texture_border_clamp,
GL_ARB_texture_cube_map, GL_ARB_texture_env_add,
GL_ARB_texture_env_combine, GL_ARB_texture_env_dot3,
GL_ARB_transpose_matrix, GL_EXT_abgr, GL_EXT_blend_color,
GL_EXT_blend_minmax, GL_EXT_blend_subtract, GL_EXT_texture_env_add,
GL_EXT_texture_env_combine, GL_EXT_texture_env_dot3,
GL_EXT_texture_lod_bias
visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
0x23 24 tc 0 24 0 r y . 8 8 8 0 0 16 0 0 0 0 0 0 0 None
0x24 24 tc 0 24 0 r y . 8 8 8 0 0 16 8 16 16 16 0 0 0 None
0x25 24 tc 0 32 0 r y . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
0x26 24 tc 0 32 0 r . . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
0x27 24 dc 0 24 0 r y . 8 8 8 0 0 16 0 0 0 0 0 0 0 None
0x28 24 dc 0 24 0 r y . 8 8 8 0 0 16 8 16 16 16 0 0 0 None
0x29 24 dc 0 32 0 r y . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
0x2a 24 dc 0 32 0 r . . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
Xorg.0.log:
X Window System Version 7.2.0
Release Date: 22 January 2007
X Protocol Version 11, Revision 0, Release 7.2
Build Operating System: UNKNOWN
Current Operating System: Linux yggdrasil 2.6.21-ARCH #1 SMP PREEMPT Mon Jun 11 23:47:51 CEST 2007 i686
Build Date: 08 April 2007
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Jul 11 10:14:15 2007
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Xorg"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Input Device "Keyboard0"
(**) Option "XkbRules" "xorg"
(**) XKB: rules: "xorg"
(**) Option "XkbModel" "pc105"
(**) XKB: model: "pc105"
(**) Option "XkbLayout" "gb"
(**) XKB: layout: "gb"
(==) Keyboard: CustomKeycode disabled
(**) |-->Input Device "mx518"
(**) FontPath set to:
/usr/share/fonts/misc:unscaled,
/usr/share/fonts/misc,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/75dpi,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/100dpi,
/usr/share/fonts/cyrillic,
/usr/share/fonts/Type1,
/usr/share/fonts/TTF
(**) RgbPath set to "/usr/share/X11/rgb"
(**) ModulePath set to "/usr/lib/xorg/modules"
(**) Option "AllowMouseOpenFail" "true"
(**) Option "AIGLX" "off"
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) Loader magic: 0x81c44a0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.3
X.Org Video Driver: 1.1
X.Org XInput driver : 0.7
X.Org Server Extension : 0.3
X.Org Font Renderer : 0.5
(II) Loader running on linux
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/xorg/modules//libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 1.1
(++) using VT number 7
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1106,0269 card 1043,8122 rev 80 class 06,00,00 hdr 80
(II) PCI: 00:00:1: chip 1106,1269 card 1043,8122 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:00:2: chip 1106,2269 card 1043,8122 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:00:3: chip 1106,3269 card 1043,8122 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:00:4: chip 1106,4269 card 1043,8122 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:00:7: chip 1106,7269 card 1043,8122 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 1106,b198 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:0a:0: chip 1102,0004 card 1102,2002 rev 04 class 04,01,00 hdr 80
(II) PCI: 00:0a:1: chip 1102,7003 card 1102,0040 rev 04 class 09,80,00 hdr 80
(II) PCI: 00:0a:2: chip 1102,4001 card 1102,0010 rev 04 class 0c,00,10 hdr 80
(II) PCI: 00:0e:0: chip 1317,0985 card 1317,0574 rev 11 class 02,00,00 hdr 00
(II) PCI: 00:0f:0: chip 1106,3149 card 1043,80ed rev 80 class 01,04,00 hdr 80
(II) PCI: 00:0f:1: chip 1106,0571 card 1043,80ed rev 06 class 01,01,8a hdr 00
(II) PCI: 00:10:0: chip 1106,3038 card 1106,3038 rev 81 class 0c,03,00 hdr 80
(II) PCI: 00:10:1: chip 1106,3038 card 1106,3038 rev 81 class 0c,03,00 hdr 80
(II) PCI: 00:10:2: chip 1106,3038 card 1106,3038 rev 81 class 0c,03,00 hdr 80
(II) PCI: 00:10:3: chip 1106,3038 card 1106,3038 rev 81 class 0c,03,00 hdr 80
(II) PCI: 00:10:4: chip 1106,3104 card 1106,3104 rev 86 class 0c,03,20 hdr 80
(II) PCI: 00:11:0: chip 1106,3227 card 1043,80ed rev 00 class 06,01,00 hdr 80
(II) PCI: 00:11:5: chip 1106,3059 card 1043,810d rev 60 class 04,01,00 hdr 00
(II) PCI: 00:11:6: chip 1106,3068 card 0000,0000 rev 80 class 07,80,00 hdr 00
(II) PCI: 01:00:0: chip 1002,4e48 card 1002,0002 rev 00 class 03,00,00 hdr 80
(II) PCI: 01:00:1: chip 1002,4e68 card 1002,0003 rev 00 class 03,80,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000b (VGA_EN is set)
(II) Bus 1 I/O range:
[0] -1 0 0x0000d000 - 0x0000dfff (0x1000) IX[b]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xfd900000 - 0xfdefffff (0x600000) MX[b]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0x9ff00000 - 0xbfefffff (0x20000000) MX[b]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:17:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(--) PCI:*(1:0:0) ATI Technologies Inc Radeon R350 [Radeon 9800 Pro] rev 0, Mem @ 0xb0000000/27, 0xfde00000/16, I/O @ 0xd000/8, BIOS @ 0xfdd00000/17
(--) PCI: (1:0:1) ATI Technologies Inc Radeon R350 [Radeon 9800 Pro] (Secondary) rev 0, Mem @ 0xa8000000/27, 0xfdc00000/16
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) OS-reported resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) PCI Memory resource overlap reduced 0xe0000000 from 0xe7ffffff to 0xdfffffff
(II) Active PCI resource ranges:
[0] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[1] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[2] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[3] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[4] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[5] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[6] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[7] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[8] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[9] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[10] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[11] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[12] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[13] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[14] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[15] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[16] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[17] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[18] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[19] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[20] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[21] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[22] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[23] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[24] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[25] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[26] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[1] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[2] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[3] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[4] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[5] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[6] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[7] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[8] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[9] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[10] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[11] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[12] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[13] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[14] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[15] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[16] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[17] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[18] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[19] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[20] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[21] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[22] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[23] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[24] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[25] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[26] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) All system resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[5] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[6] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[7] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[8] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[9] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[10] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[11] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[12] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[13] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[15] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[16] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[17] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[18] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[19] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[20] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[21] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[22] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[23] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[24] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[25] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[26] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[27] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[28] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[29] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[30] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[31] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[32] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
(II) LoadModule: "ddc"
(II) Loading /usr/lib/xorg/modules//libddc.so
(II) Module ddc: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 1.1
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension XFree86-DRI
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(**) AIGLX disabled
(II) Loading extension GLX
(II) LoadModule: "type1"
(II) Loading /usr/lib/xorg/modules/fonts//libtype1.so
(II) Module type1: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font Type1
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 7.2.0, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font FreeType
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension RECORD
(II) LoadModule: "fglrx"
(II) Loading /usr/lib/xorg/modules/drivers//fglrx_drv.so
(II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
compiled for 7.1.0, module version = 8.38.6
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 1.0
(II) LoadModule: "fglrx"
(II) Reloading /usr/lib/xorg/modules/drivers//fglrx_drv.so
(II) LoadModule: "keyboard"
(II) Loading /usr/lib/xorg/modules/input//keyboard_drv.so
(II) Module keyboard: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.7
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.1.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.7
(II) Primary Device is: PCI 01:00:0
(II) ATI Proprietary Linux Driver Version Identifier:8.38.6
(II) ATI Proprietary Linux Driver Release Identifier: LGDr8.38g1
(II) ATI Proprietary Linux Driver Build Date: Jun 22 2007 13:10:21
(II) ATI Proprietary Linux Driver Build Information: autobuild-rel-r6-8.38.1.1.2.3-driver-lnx-x86-x86_64-351593
(--) Assigning device section with no busID to primary device
(WW) fglrx: No matching Device section for instance (BusID PCI:1:0:1) found
(--) Chipset Supported AMD Graphics Processor (0x4E48) found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[5] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[6] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[7] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[8] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[9] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[10] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[11] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[12] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[13] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[15] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[16] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[17] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[18] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[19] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[20] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[21] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[22] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[23] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[24] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[25] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[26] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[27] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[28] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[29] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[30] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[31] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[32] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
(II) fglrx(0): pEnt->device->identifier=0x81e4088
(II) resource ranges after probing:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[5] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[6] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[7] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[8] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[9] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[10] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[11] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[12] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[13] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[14] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[15] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[16] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[17] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[18] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[19] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[20] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[21] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[22] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[23] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[24] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[25] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[26] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[27] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[28] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[29] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[30] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[31] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[32] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[33] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[34] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[35] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
[36] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[37] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) Setting vga for screen 0.
(II) fglrx(0): === [atiddxPreInit] === begin, [x]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 1.1
(II) fglrx(0): PCI bus 1 card 0 func 0
(**) fglrx(0): Depth 24, (--) framebuffer bpp 32
(II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) fglrx(0): Default visual is TrueColor
(**) fglrx(0): Option "DPMS" "true"
(==) fglrx(0): RGB weight 888
(II) fglrx(0): Using 8 bits per RGB (8 bit DAC)
(==) fglrx(0): Gamma Correction for I is 0x06419064
(==) fglrx(0): Gamma Correction for II is 0x06419064
(==) fglrx(0): Buffer Tiling is ON
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 1.1
(WW) fglrx(0): Bad V_BIOS checksum
(II) fglrx(0): Primary V_BIOS segment is: 0xc000
(--) fglrx(0): Chipset: "RADEON 9800 PRO" (Chipset = 0x4e48)
(--) fglrx(0): (PciSubVendor = 0x1002, PciSubDevice = 0x0002)
(--) fglrx(0): board vendor info: original ATI graphics adapter
(--) fglrx(0): Linear framebuffer (phys) at 0xb0000000
(--) fglrx(0): MMIO registers at 0xfde00000
(==) fglrx(0): ROM-BIOS at 0x000c0000
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.1.0
ABI class: X.Org Video Driver, version 1.1
(II) fglrx(0): VESA BIOS detected
(II) fglrx(0): VESA VBE Version 2.0
(II) fglrx(0): VESA VBE Total Mem: 16384 kB
(II) fglrx(0): VESA VBE OEM: ATI R360
(II) fglrx(0): VESA VBE OEM Software Rev: 1.0
(II) fglrx(0): VESA VBE OEM Vendor: ATI Technologies Inc.
(II) fglrx(0): VESA VBE OEM Product: R360
(II) fglrx(0): VESA VBE OEM Product Rev: 01.00
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmGetBusid returned ''
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Loading /usr/lib/xorg/modules/linux//libfglrxdrm.so
(II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
compiled for 7.1.0, module version = 8.38.6
ABI class: X.Org Server Extension, version 0.3
(--) fglrx(0): VideoRAM: 131072 kByte, Type: DDR SGRAM / SDRAM
(II) fglrx(0): AGP card detected
(II) fglrx(0): board/chipset is supported by this driver (original ATI board)
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/lib/xorg/modules//libddc.so
(II) fglrx(0): Connected Display1: DFP on internal TMDS [tmds1]
(II) fglrx(0): Display1 EDID data ---------------------------
(II) fglrx(0): Manufacturer: AIC Model: 9450 Serial#: 329
(II) fglrx(0): Year: 2006 Week: 33
(II) fglrx(0): EDID Version: 1.3
(II) fglrx(0): Digital Display Input
(II) fglrx(0): Max H-Image Size [cm]: horiz.: 37 vert.: 30
(II) fglrx(0): Gamma: 2.20
(II) fglrx(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) fglrx(0): First detailed timing not preferred mode in violation of standard!(II) fglrx(0): redX: 0.647 redY: 0.346 greenX: 0.298 greenY: 0.591
(II) fglrx(0): blueX: 0.150 blueY: 0.118 whiteX: 0.313 whiteY: 0.329
(II) fglrx(0): Supported VESA Video Modes:
(II) fglrx(0): 720x400@70Hz
(II) fglrx(0): 640x480@60Hz
(II) fglrx(0): 640x480@67Hz
(II) fglrx(0): 640x480@72Hz
(II) fglrx(0): 640x480@75Hz
(II) fglrx(0): 800x600@56Hz
(II) fglrx(0): 800x600@60Hz
(II) fglrx(0): 800x600@72Hz
(II) fglrx(0): 800x600@75Hz
(II) fglrx(0): 832x624@75Hz
(II) fglrx(0): 1024x768@60Hz
(II) fglrx(0): 1024x768@70Hz
(II) fglrx(0): 1024x768@75Hz
(II) fglrx(0): 1280x1024@75Hz
(II) fglrx(0): 1152x870@75Hz
(II) fglrx(0): Manufacturer's mask: 0
(II) fglrx(0): Supported Future Video Modes:
(II) fglrx(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) fglrx(0): #1: hsize: 1280 vsize 1024 refresh: 70 vid: 35457
(II) fglrx(0): #2: hsize: 1280 vsize 1024 refresh: 72 vid: 35969
(II) fglrx(0): Supported additional Video Mode:
(II) fglrx(0): clock: 135.0 MHz Image Size: 376 x 301 mm
(II) fglrx(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0
(II) fglrx(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0
(II) fglrx(0): Supported additional Video Mode:
(II) fglrx(0): clock: 25.2 MHz Image Size: 376 x 301 mm
(II) fglrx(0): h_active: 640 h_sync: 656 h_sync_end 752 h_blank_end 800 h_border: 0
(II) fglrx(0): v_active: 350 v_sync: 387 v_sync_end 389 v_blanking: 449 v_border: 0
(II) fglrx(0): Ranges: V min: 50 V max: 75 Hz, H min: 30 H max: 80 kHz, PixClock max 140 MHz
(II) fglrx(0): Monitor name: F-419
(II) fglrx(0): EDID (in hex):
(II) fglrx(0): 00ffffffffffff000523509449010000
(II) fglrx(0): 2110010380251e78e8e595a5584c9726
(II) fglrx(0): 1e5054bfef808180818a818c01010101
(II) fglrx(0): 010101010101bc34009851002a403070
(II) fglrx(0): 1300782d1100001ed60980a0205e6310
(II) fglrx(0): 10605208782d1100001a000000fd0032
(II) fglrx(0): 4b1e500e000a202020202020000000fc
(II) fglrx(0): 00462d3431390a2020202020202000ba
(II) fglrx(0): End of Display1 EDID data --------------------
(WW) fglrx(0): Only one display is connnected,so single mode is enabled
(II) fglrx(0): Primary Controller - DFP on internal TMDS
(II) fglrx(0): Internal Desktop Setting: 0x00000001
(II) fglrx(0): POWERplay not supported on this hardware
(==) fglrx(0): Qbs disabled
(==) fglrx(0): FAST_SWAP disabled
(==) fglrx(0): PseudoColor visuals disabled
(==) fglrx(0): Using gamma correction (1.0, 1.0, 1.0)
(==) fglrx(0): Center Mode is disabled
(==) fglrx(0): TMDS coherent mode is enabled
(II) fglrx(0): Total of 37 modes found for primary display.
(--) fglrx(0): Virtual size is 1280x1024 (pitch 0)
(**) fglrx(0): *Mode "1280x1024": 135.0 MHz (scaled from 0.0 MHz), 80.0 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1280x1024" 135.00 1280 1328 1440 1688 1024 1025 1028 1066
(**) fglrx(0): Default mode "1280x1024": 128.9 MHz (scaled from 0.0 MHz), 74.6 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1280x1024" 128.94 1280 1368 1504 1728 1024 1025 1028 1066 +hsync
(**) fglrx(0): Default mode "1280x1024": 108.0 MHz (scaled from 0.0 MHz), 64.0 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1280x1024" 108.00 1280 1328 1440 1688 1024 1025 1028 1066
(**) fglrx(0): Default mode "1280x1024": 85.5 MHz (scaled from 0.0 MHz), 50.9 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "1280x1024" 85.51 1280 1344 1480 1680 1024 1025 1028 1083 interlace +hsync
(**) fglrx(0): Default mode "1280x1024": 77.8 MHz (scaled from 0.0 MHz), 46.3 kHz, 43.0 Hz (I)
(II) fglrx(0): Modeline "1280x1024" 77.80 1280 1344 1480 1680 1024 1025 1028 1077 interlace +hsync
(**) fglrx(0): *Mode "1024x768": 78.8 MHz (scaled from 0.0 MHz), 60.0 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1024x768" 78.75 1024 1040 1136 1312 768 769 772 800
(**) fglrx(0): Default mode "1024x768": 78.4 MHz (scaled from 0.0 MHz), 57.7 kHz, 72.0 Hz
(II) fglrx(0): Modeline "1024x768" 78.43 1024 1080 1192 1360 768 769 772 801 +hsync
(**) fglrx(0): Default mode "1024x768": 75.0 MHz (scaled from 0.0 MHz), 56.5 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 +hsync +vsync
(**) fglrx(0): Default mode "1024x768": 65.0 MHz (scaled from 0.0 MHz), 48.4 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 +hsync +vsync
(**) fglrx(0): *Mode "800x600": 49.5 MHz (scaled from 0.0 MHz), 46.9 kHz, 75.0 Hz
(II) fglrx(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625
(**) fglrx(0): Default mode "800x600": 50.0 MHz (scaled from 0.0 MHz), 48.1 kHz, 72.0 Hz
(II) fglrx(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666
(**) fglrx(0): Default mode "800x600": 45.5 MHz (scaled from 0.0 MHz), 43.8 kHz, 70.0 Hz
(II) fglrx(0): Modeline "800x600" 45.50 800 840 920 1040 600 601 604 625 +hsync
(**) fglrx(0): Default mode "800x600": 40.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.0 Hz
(II) fglrx(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628
(**) fglrx(0): Default mode "800x600": 36.0 MHz (scaled from 0.0 MHz), 35.2 kHz, 56.0 Hz
(II) fglrx(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625
(**) fglrx(0): Default mode "800x600": 29.6 MHz (scaled from 0.0 MHz), 29.8 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "800x600" 29.60 800 816 896 992 600 601 604 635 interlace +hsync
(**) fglrx(0): *Mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.5 kHz, 75.0 Hz
(II) fglrx(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 +hsync +vsync
(**) fglrx(0): Default mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.9 kHz, 72.0 Hz
(II) fglrx(0): Modeline "640x480" 31.50 640 664 704 832 480 489 492 520 +hsync +vsync
(**) fglrx(0): Default mode "640x480": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "640x480" 25.18 640 656 752 800 480 490 492 525 +hsync +vsync
(**) fglrx(0): Default mode "1152x864": 108.0 MHz (scaled from 0.0 MHz), 67.5 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1152x864" 108.00 1152 1216 1344 1600 864 865 868 900
(**) fglrx(0): Default mode "1152x864": 96.8 MHz (scaled from 0.0 MHz), 63.0 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1152x864" 96.76 1152 1224 1344 1536 864 865 868 900 +hsync
(**) fglrx(0): Default mode "1152x864": 81.6 MHz (scaled from 0.0 MHz), 53.7 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1152x864" 81.62 1152 1216 1336 1520 864 865 868 895 +hsync
(**) fglrx(0): Default mode "1152x864": 64.7 MHz (scaled from 0.0 MHz), 43.0 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "1152x864" 64.67 1152 1208 1328 1504 864 865 868 915 interlace +hsync
(**) fglrx(0): Default mode "1152x864": 58.3 MHz (scaled from 0.0 MHz), 39.2 kHz, 43.0 Hz (I)
(II) fglrx(0): Modeline "1152x864" 58.28 1152 1200 1320 1488 864 865 868 911 interlace +hsync
(**) fglrx(0): Default mode "1024x480": 38.2 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1024x480" 38.16 1024 1048 1152 1280 480 481 484 497 +hsync
(**) fglrx(0): Default mode "848x480": 31.5 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "848x480" 31.48 848 864 952 1056 480 481 484 497 +hsync
(**) fglrx(0): Default mode "720x576": 32.7 MHz (scaled from 0.0 MHz), 35.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "720x576" 32.66 720 744 816 912 576 577 580 597 +hsync
(**) fglrx(0): Default mode "720x480": 26.7 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "720x480" 26.71 720 736 808 896 480 481 484 497 +hsync
(**) fglrx(0): Default mode "640x400": 28.1 MHz (scaled from 0.0 MHz), 33.7 kHz, 75.0 Hz
(II) fglrx(0): Modeline "640x400" 28.07 640 696 736 832 400 413 415 449
(**) fglrx(0): Default mode "640x400": 24.9 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "640x400" 24.92 640 664 760 792 400 460 462 525
(**) fglrx(0): Default mode "640x350": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 70.0 Hz
(II) fglrx(0): Modeline "640x350" 25.18 640 656 752 800 350 387 389 449 +vsync
(**) fglrx(0): Default mode "512x384": 19.8 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "512x384" 19.81 512 544 624 664 384 451 453 497
(**) fglrx(0): Default mode "400x300": 24.8 MHz (scaled from 0.0 MHz), 46.9 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "400x300" 24.75 400 408 448 528 300 601 602 625 doublescan
(**) fglrx(0): Default mode "400x300": 22.3 MHz (scaled from 0.0 MHz), 45.0 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "400x300" 22.33 400 416 480 496 300 601 605 742 doublescan
(**) fglrx(0): Default mode "320x240": 15.8 MHz (scaled from 0.0 MHz), 37.9 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "320x240" 15.75 320 328 360 416 240 481 482 501 doublescan
(**) fglrx(0): Default mode "320x240": 12.6 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "320x240" 12.59 320 328 376 400 240 491 493 525 doublescan
(**) fglrx(0): Default mode "320x200": 13.1 MHz (scaled from 0.0 MHz), 31.5 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "320x200" 13.10 320 352 368 416 200 406 407 417 doublescan
(**) fglrx(0): Default mode "320x200": 12.6 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "320x200" 12.59 320 336 384 400 200 457 459 524 doublescan
(--) fglrx(0): Display dimensions: (370, 300) mm
(--) fglrx(0): DPI set to (87, 86)
(--) fglrx(0): Virtual size is 1280x1024 (pitch 1280)
(**) fglrx(0): *Mode "1280x1024": 135.0 MHz (scaled from 0.0 MHz), 80.0 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1280x1024" 135.00 1280 1328 1440 1688 1024 1025 1028 1066
(**) fglrx(0): Default mode "1280x1024": 128.9 MHz (scaled from 0.0 MHz), 74.6 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1280x1024" 128.94 1280 1368 1504 1728 1024 1025 1028 1066 +hsync
(**) fglrx(0): Default mode "1280x1024": 108.0 MHz (scaled from 0.0 MHz), 64.0 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1280x1024" 108.00 1280 1328 1440 1688 1024 1025 1028 1066
(**) fglrx(0): Default mode "1280x1024": 85.5 MHz (scaled from 0.0 MHz), 50.9 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "1280x1024" 85.51 1280 1344 1480 1680 1024 1025 1028 1083 interlace +hsync
(**) fglrx(0): Default mode "1280x1024": 77.8 MHz (scaled from 0.0 MHz), 46.3 kHz, 43.0 Hz (I)
(II) fglrx(0): Modeline "1280x1024" 77.80 1280 1344 1480 1680 1024 1025 1028 1077 interlace +hsync
(**) fglrx(0): *Mode "1024x768": 78.8 MHz (scaled from 0.0 MHz), 60.0 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1024x768" 78.75 1024 1040 1136 1312 768 769 772 800
(**) fglrx(0): Default mode "1024x768": 78.4 MHz (scaled from 0.0 MHz), 57.7 kHz, 72.0 Hz
(II) fglrx(0): Modeline "1024x768" 78.43 1024 1080 1192 1360 768 769 772 801 +hsync
(**) fglrx(0): Default mode "1024x768": 75.0 MHz (scaled from 0.0 MHz), 56.5 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 +hsync +vsync
(**) fglrx(0): Default mode "1024x768": 65.0 MHz (scaled from 0.0 MHz), 48.4 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 +hsync +vsync
(**) fglrx(0): *Mode "800x600": 49.5 MHz (scaled from 0.0 MHz), 46.9 kHz, 75.0 Hz
(II) fglrx(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625
(**) fglrx(0): Default mode "800x600": 50.0 MHz (scaled from 0.0 MHz), 48.1 kHz, 72.0 Hz
(II) fglrx(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666
(**) fglrx(0): Default mode "800x600": 45.5 MHz (scaled from 0.0 MHz), 43.8 kHz, 70.0 Hz
(II) fglrx(0): Modeline "800x600" 45.50 800 840 920 1040 600 601 604 625 +hsync
(**) fglrx(0): Default mode "800x600": 40.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.0 Hz
(II) fglrx(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628
(**) fglrx(0): Default mode "800x600": 36.0 MHz (scaled from 0.0 MHz), 35.2 kHz, 56.0 Hz
(II) fglrx(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625
(**) fglrx(0): Default mode "800x600": 29.6 MHz (scaled from 0.0 MHz), 29.8 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "800x600" 29.60 800 816 896 992 600 601 604 635 interlace +hsync
(**) fglrx(0): *Mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.5 kHz, 75.0 Hz
(II) fglrx(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 +hsync +vsync
(**) fglrx(0): Default mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.9 kHz, 72.0 Hz
(II) fglrx(0): Modeline "640x480" 31.50 640 664 704 832 480 489 492 520 +hsync +vsync
(**) fglrx(0): Default mode "640x480": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "640x480" 25.18 640 656 752 800 480 490 492 525 +hsync +vsync
(**) fglrx(0): Default mode "1152x864": 108.0 MHz (scaled from 0.0 MHz), 67.5 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1152x864" 108.00 1152 1216 1344 1600 864 865 868 900
(**) fglrx(0): Default mode "1152x864": 96.8 MHz (scaled from 0.0 MHz), 63.0 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1152x864" 96.76 1152 1224 1344 1536 864 865 868 900 +hsync
(**) fglrx(0): Default mode "1152x864": 81.6 MHz (scaled from 0.0 MHz), 53.7 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1152x864" 81.62 1152 1216 1336 1520 864 865 868 895 +hsync
(**) fglrx(0): Default mode "1152x864": 64.7 MHz (scaled from 0.0 MHz), 43.0 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "1152x864" 64.67 1152 1208 1328 1504 864 865 868 915 interlace +hsync
(**) fglrx(0): Default mode "1152x864": 58.3 MHz (scaled from 0.0 MHz), 39.2 kHz, 43.0 Hz (I)
(II) fglrx(0): Modeline "1152x864" 58.28 1152 1200 1320 1488 864 865 868 911 interlace +hsync
(**) fglrx(0): Default mode "1024x480": 38.2 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1024x480" 38.16 1024 1048 1152 1280 480 481 484 497 +hsync
(**) fglrx(0): Default mode "848x480": 31.5 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "848x480" 31.48 848 864 952 1056 480 481 484 497 +hsync
(**) fglrx(0): Default mode "720x576": 32.7 MHz (scaled from 0.0 MHz), 35.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "720x576" 32.66 720 744 816 912 576 577 580 597 +hsync
(**) fglrx(0): Default mode "720x480": 26.7 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "720x480" 26.71 720 736 808 896 480 481 484 497 +hsync
(**) fglrx(0): Default mode "640x400": 28.1 MHz (scaled from 0.0 MHz), 33.7 kHz, 75.0 Hz
(II) fglrx(0): Modeline "640x400" 28.07 640 696 736 832 400 413 415 449
(**) fglrx(0): Default mode "640x400": 24.9 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "640x400" 24.92 640 664 760 792 400 460 462 525
(**) fglrx(0): Default mode "640x350": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 70.0 Hz
(II) fglrx(0): Modeline "640x350" 25.18 640 656 752 800 350 387 389 449 +vsync
(**) fglrx(0): Default mode "512x384": 19.8 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "512x384" 19.81 512 544 624 664 384 451 453 497
(**) fglrx(0): Default mode "400x300": 24.8 MHz (scaled from 0.0 MHz), 46.9 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "400x300" 24.75 400 408 448 528 300 601 602 625 doublescan
(**) fglrx(0): Default mode "400x300": 22.3 MHz (scaled from 0.0 MHz), 45.0 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "400x300" 22.33 400 416 480 496 300 601 605 742 doublescan
(**) fglrx(0): Default mode "320x240": 15.8 MHz (scaled from 0.0 MHz), 37.9 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "320x240" 15.75 320 328 360 416 240 481 482 501 doublescan
(**) fglrx(0): Default mode "320x240": 12.6 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "320x240" 12.59 320 328 376 400 240 491 493 525 doublescan
(**) fglrx(0): Default mode "320x200": 13.1 MHz (scaled from 0.0 MHz), 31.5 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "320x200" 13.10 320 352 368 416 200 406 407 417 doublescan
(**) fglrx(0): Default mode "320x200": 12.6 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "320x200" 12.59 320 336 384 400 200 457 459 524 doublescan
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.3
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/lib/xorg/modules//libramdac.so
(II) Module ramdac: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 1.1
(==) fglrx(0): NoAccel = NO
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib/xorg/modules//libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.2.0
ABI class: X.Org Video Driver, version 1.1
(==) fglrx(0): HPV inactive
(**) fglrx(0): FSAA enabled: NO
(==) fglrx(0): FSAA Gamma enabled
(==) fglrx(0): FSAA Multisample Position is fix
(==) fglrx(0): NoDRI = NO
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Reloading /usr/lib/xorg/modules/linux//libfglrxdrm.so
(II) fglrx(0): Depth moves disabled by default
(==) fglrx(0): Capabilities: 0x00000000
(==) fglrx(0): CapabilitiesEx: 0x00000000
(==) fglrx(0): cpuFlags: 0x4000000f
(==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
(II) fglrx(0): [drm] DRM buffer queue setup: nbufs = 100 bufsize = 65536
(==) fglrx(0): UseFastTLS=0
(==) fglrx(0): BlockSignalsOnLock=1
(==) fglrx(0): EnablePrivateBackZ = NO
(II) LoadModule: "glesx.so" (glesx)
(WW) LoadModule: given non-canonical module name "glesx.so"
(II) Loading /usr/lib/xorg/modules//glesx.so
(II) Module glesx: vendor="X.Org Foundation"
compiled for 7.1.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension GLESX
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b]
[1] 0 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b]
[2] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[3] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[4] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[5] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[6] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[7] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[8] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[9] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[10] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[11] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[12] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[13] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[14] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[15] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[16] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b](OprU)
[17] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b](OprU)
[18] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b](OprU)
[19] 0 0 0x0000d000 - 0x0000d0ff (0x100) IX[b]
[20] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[21] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[22] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[23] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[24] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[25] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[26] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[27] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[28] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[29] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[30] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[31] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[32] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[33] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[34] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[35] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[36] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[37] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[38] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
[39] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
[40] 0 0 0x000003c0 - 0x000003df (0x20) IS[b](OprU)
(II) fglrx(0): driver needs X.org 7.1.x.y with x.y >= 0.0
(II) fglrx(0): detected X.org 7.1.0.0
(II) Loading extension ATIFGLRXDRI
(II) fglrx(0): doing DRIScreenInit
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenByBusid: Searching for BusID PCI:1:0:0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenByBusid: drmOpenMinor returns 6
drmOpenByBusid: drmGetBusid reports
drmOpenDevice: node name is /dev/dri/card1
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card2
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card3
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card4
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card5
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card6
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card7
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card8
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card9
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card10
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card11
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card12
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card13
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card14
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmGetBusid returned ''
(II) fglrx(0): [drm] DRM interface version 1.0
(II) fglrx(0): [drm] created "fglrx" driver at busid "PCI:1:0:0"
(II) fglrx(0): [drm] added 8192 byte SAREA at 0xb4000
(II) fglrx(0): [drm] mapped SAREA 0xb4000 to 0xb7282000
(II) fglrx(0): [drm] framebuffer handle = 0xb5000
(II) fglrx(0): [drm] added 1 reserved context for kernel
(II) fglrx(0): DRIScreenInit done
(II) fglrx(0): Kernel Module Version Information:
(II) fglrx(0): Name: fglrx
(II) fglrx(0): Version: 8.37.6
(II) fglrx(0): Date: May 25 2007
(II) fglrx(0): Desc: ATI FireGL DRM kernel module
(WW) fglrx(0): Kernel Module version does *not* match driver.
(EE) fglrx(0): incompatible kernel module detected - HW accelerated OpenGL will not work
(II) fglrx(0): [drm] removed 1 reserved context for kernel
(II) fglrx(0): [drm] unmapping 8192 bytes of SAREA 0xb4000 at 0xb7282000
(WW) fglrx(0): ***********************************************
(WW) fglrx(0): * DRI initialization failed! *
(WW) fglrx(0): * (maybe driver kernel module missing or bad) *
(WW) fglrx(0): * 2D acceleraton available (MMIO) *
(WW) fglrx(0): * no 3D acceleration available *
(WW) fglrx(0): ********************************************* *
(II) fglrx(0): FBADPhys: 0xb0000000 FBMappedSize: 0x08000000
(==) fglrx(0): Write-combining range (0xb0000000,0x8000000)
(II) fglrx(0): FBMM initialized for area (0,0)-(1280,8191)
(II) fglrx(0): FBMM auto alloc for area (0,0)-(1280,1024) (front color buffer - assumption)
(II) fglrx(0): Largest offscreen area available: 1280 x 7167
(==) fglrx(0): Backing store disabled
(==) fglrx(0): Silken mouse enabled
(II) Loading extension FGLRXEXTENSION
(II) Loading extension ATITVOUT
(**) fglrx(0): DPMS enabled
(II) fglrx(0): GLESX enableFlags = 0
(II) fglrx(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
Solid Horizontal and Vertical Lines
Offscreen Pixmaps
Setting up tile and stipple cache:
32 128x128 slots
32 256x256 slots
16 512x512 slots
(II) fglrx(0): Acceleration enabled
(II) fglrx(0): Direct rendering disabled
(==) fglrx(0): Using hardware cursor
fbarea0->box.x1 0x00000000, fbarea0->box.y1 0x00000404
fbarea0->box.x2 0x00000500, fbarea0->box.y2 0x00000406
icon[0].start=0x505000
fbarea1->box.x1 0x00000000, fbarea1->box.y1 0x00000406
fbarea1->box.x2 0x00000500, fbarea1->box.y2 0x00000408
icon[1].start=0x508000
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) Loading local sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/lib/xorg/modules/extensions//libGLcore.so
(II) Module GLcore: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) GLX: Initialized MESA-PROXY GL provider for screen 0
[glesx] __glESXExtensionInit: No GL ES2.0 capable screen found!
(**) Option "CoreKeyboard"
(**) Keyboard0: Core Keyboard
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Keyboard0: XkbModel: "pc105"
(**) Option "XkbLayout" "gb"
(**) Keyboard0: XkbLayout: "gb"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(**) Option "Protocol" "ExplorerPS/2"
(**) mx518: Device: "/dev/input/mice"
(**) mx518: Protocol: "ExplorerPS/2"
(**) Option "CorePointer"
(**) mx518: Core Pointer
(**) Option "Device" "/dev/input/mice"
(**) Option "Buttons" "10"
(==) mx518: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5"
(**) mx518: ZAxisMapping: buttons 4 and 5
(**) Option "ButtonMapping" "1 2 3 6 7"
(**) mx518: Buttons: 14
(**) Option "Resolution" "800"
(**) mx518: Resolution: 800
(II) XINPUT: Adding extended input device "mx518" (type: MOUSE)
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) mx518: ps2EnableDataReporting: succeeded
xorg.conf:
Section "ServerLayout"
Identifier "Xorg"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "mx518" "CorePointer"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "true"
Option "AIGLX" "off" # Disable AIGLX
EndSection
Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
# Fonts
FontPath "/usr/share/fonts/misc:unscaled"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/75dpi"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/100dpi"
FontPath "/usr/share/fonts/cyrillic"
FontPath "/usr/share/fonts/Type1"
FontPath "/usr/share/fonts/TTF"
EndSection
Section "Module"
Load "ddc" # ddc probing of monitor
Load "dbe"
Load "dri"
Load "drm"
Load "extmod"
Load "glx"
Load "bitmap" # bitmap-fonts
Load "type1"
Load "freetype"
Load "record"
Load "fglrx"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
# Options
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "gb"
# Option "XkbVariant" ""
EndSection
Section "InputDevice"
Identifier "mx518"
Driver "mouse"
# Options
Option "CorePointer"
Option "Resolution" "800"
Option "Device" "/dev/input/mice"
Option "Protocol" "ExplorerPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "10"
Option "ButtonMapping" "1 2 3 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "AG Neovo"
ModelName "F-419"
HorizSync 24.0 - 80.0
VertRefresh 50.0 - 75.0
# Options
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "Card0"
VendorName "All"
BoardName "All"
Driver "fglrx"
# Options
# Option "XAANoOffscreenPixmaps" "true"
# Option "AGPMode" "8"
# Option "ColorTiling" "on"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultColorDepth 24
SubSection "Display"
Depth 1
Modes "1280x1024" "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1280x1024" "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x1024" "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x1024" "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x1024" "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
#Section "Extensions"
# Option "XEVIE" "Enable"
# Option "Composite" "Enable"
#Endsection
Would it be possible to explain the other warnings in Xorg.0.log? Rather curious about those apart from the obvious one, too.
Thanks.
Last edited by Newnux (2007-07-11 16:04:15)Indeed, that seems the end-all error of it all.
I'll summarise my warnings, some for curious reasons:
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory) # What's this?
(WW) fglrx: No matching Device section for instance (BusID PCI:1:0:1) found # Not a problem.
(WW) fglrx(0): Only one display is connnected,so single mode is enabled # No problem.
(WW) fglrx(0): Kernel Module version does *not* match driver.
(WW) fglrx(0): ***********************************************
(WW) fglrx(0): * DRI initialization failed! *
(WW) fglrx(0): * (maybe driver kernel module missing or bad) *
(WW) fglrx(0): * 2D acceleraton available (MMIO) *
(WW) fglrx(0): * no 3D acceleration available *
(WW) fglrx(0): ********************************************* *
Anyway, I wondered about versions and noticed this:
(II) fglrx(0): [drm] DRM interface version 1.0
(II) fglrx(0): [drm] created "fglrx" driver at busid "PCI:1:0:0"
(II) fglrx(0): [drm] added 8192 byte SAREA at 0xbc000
(II) fglrx(0): [drm] mapped SAREA 0xbc000 to 0xb7285000
(II) fglrx(0): [drm] framebuffer handle = 0xbd000
(II) fglrx(0): [drm] added 1 reserved context for kernel
(II) fglrx(0): DRIScreenInit done
(II) fglrx(0): Kernel Module Version Information:
(II) fglrx(0): Name: fglrx
(II) fglrx(0): Version: 8.37.6
(II) fglrx(0): Date: May 25 2007
(II) fglrx(0): Desc: ATI FireGL DRM kernel module
(WW) fglrx(0): Kernel Module version does *not* match driver. # included to show where this was displayed
All versions previous to that show 8.38.6:
(II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
compiled for 7.1.0, module version = 8.38.6
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 1.0
So I assume I have an old version dotted around somewhere, but I'm not sure about how it's all loaded and such.
Now, quoting something I'd come across a few times and taking it from thinkwiki:
If you lose hardware acceleration after a driver update this can be caused by an old fglrx kernel module being loaded.
Check out /var/log/Xorg.0.log for a message like:
(WW) fglrx(0): Kernel Module version does *not* match driver.
(EE) fglrx(0): incompatible kernel module detected - HW accelerated OpenGL will not work
You can verify this yourself by looking at the version message some lines above. It should read something not matching the installed version like:
(II) fglrx(0): Kernel Module Version Information:
(II) fglrx(0): Name: fglrx
(II) fglrx(0): Version: 8.10.19
The cause for this trouble might be that there resist multiple versions of the fglrx module within the kernel module search path.
Go to /lib/modules/<your linux kernel version>/ and type # grep fglrx modules.dep.
If grep finds multiple lines you nailed down the problem. All you have to do now is to delete any versions of the module (look at the filedate) but the most current one. Then run # depmod and you are done.
Hint:
Newer versions (8.21.7) of the fglrx module seem to be installed in the extra/ subdirectory.
Older versions (8.19.10) used to be located in the kernel/drivers/char/drm/ subdirectory.
How does this apply to Arch? I only found one instance of fglrx by using that method.
Edit: Forgot to add that I've tried reinstalling a few times, it doesn't really seem to do anything. Wondering if I should attempt to install an older version or something, but I don't get why the driver numbers don't match for me. Surely others have updated their drivers too.
Last edited by Newnux (2007-07-11 13:28:55) -
storage-vdc(config-if)# show module
Mod Ports Module-Type Model Status
2 32 1/10 Gbps Ethernet Module N7K-F132XP-15 ok
sw1-gd78(config-if)# sh module
Mod Ports Module-Type Model Status
2 48 1/2/4/8 Gbps FC Module DS-X9248-96K9 ok
4 8 10 Gbps FCoE Module DS-X9708-K9 ok
7 0 Supervisor/Fabric-2a DS-X9530-SF2AK9 active *
8 0 Supervisor/Fabric-2a DS-X9530-SF2AK9 ha-standby
10 22 4x1GE IPS, 18x1/2/4Gbps FC Module DS-X9304-18K9 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
2 5.2(2) 1.1 20:41:00:0d:ec:fb:8a:00 to 20:70:00:0d:ec:fb:8a:00
4 5.2(2) 0.107 --
7 5.2(2) 1.8 --
8 5.2(2) 1.8 --
10 5.2(2) 1.3 22:41:00:0d:ec:fb:8a:00 to 22:52:00:0d:ec:fb:8a:00
sw1-gd78(config-if)# sh run int ethernet4/6
!Command: show running-config interface Ethernet4/6
!Time: Mon Feb 20 22:56:12 2012
version 5.2(2)
interface Ethernet4/6
no shutdown
sw1-gd78(config-if)# no shut
sw1-gd78(config-if)# speed 1000
ERROR: Ethernet4/6: Configuration does not match the port capability.
sw1-gd72# sh int ethernet4/6 capabilities
Ethernet4/6
Model: DS-X9708-K9
Type (SFP capable): 10Gbase-SR
Speed: 1000,10000
Duplex: full
Trunk encap. type: 802.1Q
Channel: yes
Broadcast suppression: percentage(0-100)
Flowcontrol: rx-(off/on/desired),tx-(off/on/desired)
Rate mode: dedicated
QOS scheduling: rx-(2q4t),tx-(1p3q4t)
CoS rewrite: yes
ToS rewrite: yes
SPAN: yes
UDLD: yes
Link Debounce: yes
Link Debounce Time: yes
MDIX: no
Port Group Members: none
TDR capable: no
FabricPath capable: yes
Port mode: Switched
sw1-gd72# sh int ethernet4/6 transceiver details
Ethernet4/6
transceiver is present
type is 10Gbase-SR
name is CISCO-FINISAR
part number is FTLX8571D3BCL-CS
revision is C
serial number is FNS12090EMJ
nominal bitrate is 10300 MBit/sec
Link length supported for 50/125um OM2 fiber is 82 m
Link length supported for 50/125um OM3 fiber is 300 m
Link length supported for 62.5/125um fiber is 26 m
cisco id is --
cisco extended id number is 4
SFP Detail Diagnostics Information (internal calibration)
Alarms Warnings
High Low High Low
Temperature 36.21 C 75.00 C -5.00 C 70.00 C 0.00 C
Voltage 3.29 V 3.63 V 2.97 V 3.46 V 3.13 V
Current 8.11 mA 11.80 mA 4.00 mA 10.80 mA 5.00 mA
Tx Power -2.65 dBm 1.49 dBm -11.30 dBm -1.50 dBm -7.30 dBm
Rx Power -2.21 dBm 1.99 dBm -13.97 dBm -1.00 dBm -9.91 dBm
Transmit Fault Count = 0
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warningAnkit,
You are trying to set speed 1000 on a 10g sfp.
type is 10Gbase-SR
You will need to insert a 1gig sfp and then you will be able to set the speed.
Also, I noticed that you posted first with interface 2/6 and the output you gave me was for 4/6. Are you sure you're in the right interface? -
Hii ..
need help on this ..
This what I am doing ..
I am using a DATAEXPORT function to export level0 data from my essbase 11.1.2.2 to Microsoft SQL 2008 tables.
So what I did first I exported the level0 data to a flat file using DATAEXPORT and the created the SQL columns by the same in that order only in my SQL table.
When I run it fails with this error:
ODBC Layer Error: [21S01] ==> [[DataDirect][ODBC SQL Server Wire Protocol driver][Microsoft SQL Server]Column name or number of supplied values does not match table definition.]
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Info(1021014)
ODBC Layer Error: Native Error code [213]
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Error(1012085)
Unable to export data to SQL table [dataexp]. Check the Essbase server log and the system console to determine the cause of the problem.
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Info(1021002)
SQL Connection is Freed
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Warning(1080014)
Transaction [ 0x1c50001( 0x51ee7d66.0x80342 ) ] aborted due to status [1012085].
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Info(1012579)
Total Calc Elapsed Time for [test.csc] : [1.44] seconds
=============================================================
I did a simple test on my Sample.basic application then ..
loaded the calc data to it and then used the below script to export to a flat file
//ESS_LOCALE English_UnitedStates.Latin1@Binary
SET DATAEXPORTOPTIONS
DataExportLevel "Level0";
DataExportOverwriteFile ON;
DataExportColFormat OFF;
DataExportDimHeader OFF;
FIX(
"Jan",
"Sales",
"Actual"
/*DATAEXPORT "File" "," "/home/hypadmin/samtest.txt";*/
DATAEXPORT "DSN" "Abhitest" "sample" "sa" "welcome1";
ENDFIX
out put as below:
"Sales"
"100-30","California"
"Jan","Actual",145
Now In sql I created only 3 columns with name Jan/Sales/Actual and when I run this script again with comments removed .. I get the same error as what I have got in my first test case with other application ..
but when I create the columns with same name as what its in export
Sales/100-30/Califirnia/Jan/Actual
It created the new rows successfully ..
So with this I think the error which I am getting with my other application might be because of the same column issue .. but then I have created all the columns by looking at the export file only as I did in sample ..
Any idea would be helpful ..
Thanks
Abhishek
IFirst make sure you add
DataExportRelationalFile ON;
to your set commands it is missing
I alwats like to also add
DataExportColHeader dimensionName;
so I am sure what dimension is getting put into the columns.
Then count the number of dimensions in your outline (exclude attribute dimensions). You need at least that many columns in your table -1 + the number of members you will be returning as columns in the export
Taking your example Sample basic has 5 dimensions
Measures
Years
Scenario
Product
Market
Since you did not specify a dataexportcolheader it took the dense dimension Scenario as the columns. Your fix statement is limiting that to one member. Doing the math
5 -1 + 1 = 5 columns in your table which is what you found works. Suppose you fixed on bothe Actual and budget in scenario then you would need 6 columns 5 -1 +2 -
Data type of the base attribute or the base value does not match...
...the assigned expression.
Hello all,
I always get the Error
+<ERROR+
TEXT="'DWH.CUB_REGISTRATIONS_AW.REGISTRATIONS': XOQ-02517: Der Datentyp des Basisattributs oder der Basisgröße stimmt nicht mit dem zugeordneten Ausdruck überein.
XOQ-01400: Ungültige Metadatenobjekte"/>
The English message must be something like this:
The data type of the base attribute or the base value does not match the assigned expression.
when I run my mapping. The attribute REGISTRATIONS is NUMERIC (12,2) in the Cube and I map a NUMERIC(12,2) constant in it.
I use a simple OWB-Mapping for loading, but I don't understand why it doesn't function. Other mappings where the attributes are out of a
table I put in a cube are running well.
I tried different things, but nothing fixed my problem. Any idea ?
Thanks a lot for help
MichaelTechnically this is a 'warning' from the server, not an 'error'. This means that the change you made should have been submitted, but you get an warning message on the client. AWM would suppress this warning, but evidently OWB does not. Can you switch to use AWM?
Here is the definition of the warning along with 'cause' and 'action' sections. (Unfortunately these sections are not translated into German for some reason.)
>
02517, 0, "The data type \"%(1)s\" of the base attribute or base measure is different from the mapped expression \"%(2)s\"."
// *Cause: Either the base attribute or base measure with the mapped expression was set to an inconsistent data type, or it was mapped to an expression of a different data type from its fixed data type.
// *Action: When changing a mapped expression for a base attribute or base measure, ensure that the expression has the same data type; otherwise, set the data type of the base attribute or base measure to NULL first. When a base attribute or a base measure has an existing mapped expression, do not set it to a different data type.
>
It is probably safe to ignore this warning, but if you can post the relevant XML for the cube, then will probably be able to spot the problem. I assume that REGISTRATIONS is a measure in the cube CUB_REGISTRATIONS_AW, so this is what you can look for in the XML:
(1) The definition of the base measure along with the datatype. It should be something like this
<Measure>
<BaseMeasure
SQLDataType="NUMBER(12,2)"
ETMeasureColumnName="REGISTRATIONS"
Name="REGISTRATIONS">(2) The mapping info for the measure, which should looks something like this:
<MeasureMap
Name="REGISTRATIONS"
Expression="...">
<Measure Name="REGISTRATIONS"/>
</MeasureMap>I don't know if you can get the XML directly from OWB. If not, then DBMS_CUBE.EXPORT_XML should work (assuming you are in 11.2). You could also attach AWM and save the cube to an XML template. -
I've completed an upgrade from Exchange 2003 to Exchange 2013 and I have one last SSL message that I can't get rid of. I've installed a 3rd party cert that is working great for webmail and cell phone access but for some reason the Outlook 2010/2013
clients get prompted for a security warning. I just implemented the SSL cert yesterday and I've noticed that new installs of Outlook seem to work just fine. My Outlook 2013 client doesn't prompt me with the message but I have other users who are
still getting the "The name of the security certificate is invalid or does not match the name of the site" error. The domain on the cert error show up as server.mydomain.local. I've gone through all the virtual directories and pointed
all of my internal and external URL's to https://mail.mydomain.com. This made one of the two warnings go away but not the second. I've dug around on google and gone through everything I could find here and as far as I can tell my internal
and external url's are configured properly and I can't figure out where this error is originating from. Any ideas on where I should look outside of the virtual directories?
I'm including a good link I found that contains all of the virtual directories I updated. I've checked them through both CLI and GUI and everything looks good.
http://www.mustbegeek.com/configure-external-and-internal-url-in-exchange-2013/
http://jaworskiblog.com/2013/04/13/setting-internal-and-external-urls-in-exchange-2013/Hi,
When the Outlook connect to Exchange 2013/Exchange 2010, the client would connect to Autodiscover service to retrieve Exchange service automatically from server side. This feature is not available in Exchange 2003 Outlook profile.
Generally, when mailbox is moved to Exchange 2013, the Outlook would connect to server to automatically update these information. It needs time to detect and update the changes in server side. I suggest we can do the following setting For autodiscover service:
Get-ClientAccessServer | Set-ClientAccessServer –AutodiscoverServiceInternalUri https://mail.mydomain.com/autodiscover/autodiscover.xml
Please restart IIS service by running IISReset in a Command Prompt window after all configuraions.
Regards,
Winnie Liang
TechNet Community Support -
The name of the security certificate is invalid or does not match the name of the site error?
I am looking for some help folks. We are in a Outlook 2007/Exchange2010/Windows2008R2 environment.
When users open Outlook off the network, and occasionally on the network, they get the error
The name of the security certificate is invalid or does not match the name of the site error
The CAS hostname is HRECAS.XXX.ORG. The URL that is listed on the SSL certificate (issued by VeriSign) is WEB.XXX.ORG. WEB.XXX.ORG is what users use to get to OWA and such.
When I use testexchangeconnectivity.com, under certificate name validation I see an error that reads:
Host name autodiscover.xxx.org doesn't match any name found on the server certificate CN=web.xxx.org.
Does this mean somehow we have to add autodiscover.xxx.org on the certificate?
I tried to add AutoDiscoverExternalUri using
http://support.microsoft.com/?kbid=940726 &
http://social.technet.microsoft.com/Forums/en-US/exchange2010/thread/2d0c0f5f-e4ec-4f33-a37d-b94fd7a2319f on the CAS server.
Set-ClientAccessServer -identity HRECAS -AutodiscoverServiceExternalUri
https://autodiscover.xxx.org/Autodiscover/Autodiscover.xml
I get an error that says
"a positional parameter cannot be found that accepts argument '-AutoDiscoverExternalUri'.
Can someone point to me what I am doing wrong with the command and whether I should be concerning myself with adding that line? By the way the
InternalUrl information is already configured on the system. Also should I edit the certificate to add autodiscover.xxx.org?
Thank in advance for your support.
TD
TDHi Tapera,
Thanks for the question.
SRV record is a good idea. You can set the SRV to
https://web.abc.com/autodiscover/autodiscover.xml but you must make sure the
url can be resolved from External clients.
In addition, there is still a issue. It is hard coded that Outlook will find the autodiscover by the orders below:
1. Access autodiscover via SCP in AD.
https://web.abc.com/autodiscover/autodiscover.xml
2. If SCP access fails, it will try:
https://abc.com/autodiscover/autodiscover.xml
3. Then
https://autodiscover.abc.com/autodiscover/autodiscover.xml
4. Local XML file
5. SRV record
As you can see, Outlook will try SRV record at last. Therefore, it will still try to access
https://autodiscover.abc.com/autodiscover/autodiscover.xml each time you run Outlook. Then the certificate warning will still persists.
I have a workaround solution. You can do a local policy to disable the autodiscover to access the
https://autodiscover.abc.ocom/autodiscover/autodiscover.xml by:
1.
On the Outlook client machine, open regedit and add the following key:
HKEY_CURRENT_USER\Software\Microsoft\Office\12.0\Outlook\Autodiscover
"ExcludeHttpsAutodiscoverDomain"
"ExcludeHttpsRootDomain"
2.
Then set the value to “1” on the above two keys.
Thanks,
Simon -
Outlook 2010 Certificate does not match
I have a problem with a new installation of Exchange 2013 on a Windows 2012 Server. Most of the clients are Outlook 2010.
All the internal users are getting the error message:
"There is a problem with the proxy server's certificate. The name on the security certificate is invalid or does not match the name of the target site exchange2013.myinternaldomain.local
This is shortly followed by another box "the name on the security certificate is invalid or does not match the name of the site"
Of course the issue is my purchased SSL certificate is MAIL.REALDOMAIN.ORG while the server's name is exchange2013.myinternaldomain.local
With Exchange 2010 servers I have deployed I have had success following KB article 940726 but this time it didn't fix it with Exchange 2013.
There must be a solution!
I found this article:
http://support.microsoft.com/kb/2783881 the first suggestion from MS were impractical and the registry edit didn't work either (plus the thought of going to all my clients to do a registry
fix doesn't make me happy!)
I tried creating a local DNS zone for my external domain name and pointing to the internal IP but that didn't fix it.
In the ECP under the Outlook Anywhere section -- "*Specify the internal host name such as contoso.com that users will use to connect
to your organization:" I changed the internal host name to the external .org address but this caused Outlook clients internally not to work.
I used the -AutodiscoverServiceInternalUrl command to point it to the .org address on the certificate but didn't work either.
I have a service record in both external and internal DNS pointing to the mail.realdomain.org address.
Any other suggestions?
Thanks in advance!
MikeThanks for the information. I actually finally got this resolved a few weeks ago by speaking directly with a Microsoft technician. I am going to post what finally fixed my problem with the hopes that it will help others in my position.
Again, the problem which I am sure is common is a .local domain internally and a "real" domain on the outside. The solution that the MS tech had me do was to simply point EVERYTHING both internally and externally to the external host name - the one that
matched the certificate I had.
I'm surprised this solution isn't found elsewhere - it seems so obvious.
He had me run an number of commandlets which I will post here - with the caveat that they were for my environment! (I've masked my real domain name and substituted - mydomainame.org)
Set-Webservicesvirtualdirectory -Identity "EXCHANGE2013\ews (Default Web Site)" -InternalURl
https://mail.mydomainname.org/ews/exchange.asmx
Set-OutlookProvider EXCH -CertPrincipalName msstd:mail.mydomainname.org
Set-OutlookProvider EXPR -CertPrincipalName msstd:mail.mydomainname.org
Set-OutlookAnywhere -Identity "EXCHANGE2013\Rpc (Default Web Site)" -InternalHostName "mail.mydomainname.org" -InternalClientsRequireSsl $True -InternalClientAuthenticationMethod NTLM
Set-Webservicesvirtualdirectory -Identity "EXCHANGE2013\ews (Default Web Site)" -InternalURl
https://mail.mydomainname.org/ews/exchange.asmx
Set-OutlookAnywhere -Identity "EXCHANGE2013\Rpc (Default Web Site)" -ExternalHostName "mail.mydomainname.org" -ExternalClientsRequireSsl $True -InternalClientAuthenticationMethod NTLM --ExternalClientAuthenticationMethod NTLM -IISAuthenticationMethods
Basic, NTLM, Negotiate
Set-OutlookProvider EXCH -CertPrincipalName msstd:mail.mydomainname.org
Set-OutlookProvider EXPR -CertPrincipalName msstd:mail.mydomainname.org
Set-OutlookAnywhere -Identity "EXCHANGE2013\Rpc (Default Web Site)" -InternalHostName "mail.mydomainname.org" -InternalClientsRequireSsl $True -InternalClientAuthenticationMethod NTLM
The last thing we did was ADD in DNS on the internal DNS server the mail.mydomainname.org and point it my Exchange Server private IP (192.168.1.2) If you do the whole host name and not just mydomainame.org it wont mess up access to say an external
website.
hope this helps!
Maybe you are looking for
-
Blacks turn dark grey after exporting to pdf from InDeign cs6
Exactly what the title says. The one on the right is from Indesign....the left one is after exporting (the same in preview and acrobat reader).Anyone know why this happens?
-
i was using "find my iphone" and when given the location it was an old location. A post read that the iphone was either turned off or the wifi was not being used. A remove or cancel button appears with this message. I accidentally clicked cancel and
-
Hello, I have this JSP code: <%@page contentType="text/html" pageEncoding="UTF-8"%> <% try { SQL_client.RozvrhServiceService service = new SQL_client.RozvrhServiceService(); SQL_client.RozvrhService port = service.getRozvrhServicePort();
-
Cannot convert avi to mp4 to my Ipod Touch
Im running on Windows XP. And I use PSP Video 9 to convert my avfi files to mp4. Now I get them converted and then I import them to itunes. I sync it to ipod but it tells me Ipod could not put it on ipod or something like that. I've tried it with 3 d
-
G4 won't boot under 10.4.11 - G3 won't connect w/G4
Not sure where to start. Use a G3 w/10.3.9 for work. Have a G4 with 10.4.11 for play. They are connected through the DSL modem. Had a crash on G4 while playing a game. Then G4 wouldn't re-boot. Gray screen, spinning wheel, I don't have the install di