WARNING: This crypto map is incomplete
Hi ,
i have ASA with 4 l2l vpn configured. as now am trying to configure new VPN tunnel; while configuring of crypto map set match add its giving me
error like ... WARNING: This crypto map is incomplete
as i have read all the discussion from forms its not effecting ; request you to please help
Thanks
Gajendra
Hi,
This is a normal message and just tells you that you have not yet entered all the "crypto map" commands related to this new connection to make the configuration complete
You will essentially have to make sure that you have ATLEAST the following lines configured
crypto map match address
crypto map set peer
crypto map set ikev1 transform-set
The "transform-set" part might NOT need the "ikev1" depending on your ASAs software level.
- Jouni
Similar Messages
-
[ERR]crypto map WARNING: This crypto map is incomplete
i have PIX 501 ver6.3(5) when i setup VPN i get this error message
WARNING:This crypto map is incomplete to remedy the situation add a peer and a valid access-list to this crypto map.
although it seems fine in sh conf command
but tunnel is not started
when i review log i found
sa_request,ISAKMP Phase 1 exchange startedi could successfully establish VPN with another FW cisco 501 6.3
but still can't fix my dilemma which i connect to Huawei Eudemon 500â
sh isakmp
PIX Version 6.3(5)â
interface ethernet0 10full
interface ethernet1 100full
nameif ethernet0 outside security0â
nameif ethernet1 inside security100 â
access-list inside_outbound_nat0_acl permit ip host internal IP host name remote internal IP1â
access-list inside_outbound_nat0_acl permit ip host internal IP host name remote internal IP2â
access-list outside_cryptomap_100 permit ip host internal IP host remote internal IP1â
access-list outside_cryptomap_100 permit ip host internal IP host remote internal IP2 â
global (outside) 1 interfaceâ
nat (inside) 0 access-list inside_outbound_nat0_acl
sysopt connection permit-ipsec
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac â
crypto ipsec security-association lifetime seconds 3600â
crypto map outside_map 100 ipsec-isakmp
crypto map outside_map 100 match address outside_cryptomap_100â
crypto map outside_map 100 set peer remote peer
crypto map outside_map 100 set transform-set ESP-3DES-SHA
crypto map outside_map 100 set security-association lifetime seconds 3600 kilobytes 1843200â
crypto map outside_map interface outside
isakmp enable outside
â â
isakmp key ******** address remote peer netmask 255.255.255.255 no-xauth no-config-mode â
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash shaâ
isakmp policy 20 group 2â
isakmp policy 20 lifetime 86400â
sh crypto map
Crypto Map: "outside_map" interfaces: { outside }â
Crypto Map "outside_map" 100 ipsec-isakmp
Peer = remote peer
access-list outside_cryptomap_100; 2 elementsâ
access-list outside_cryptomap_100 line 1 permit ip host 10.102.0.11 host remote internal IP1 ââ(hitcnt=14) â
access-list outside_cryptomap_100 line 2 permit ip host 10.102.0.11 host remote internal IP2 ââ(hitcnt=6) â
Current peer: remote peer
Security association lifetime: 1843200 kilobytes/3600 secondsâ
PFS (Y/N): N
Transform sets={ ESP-3DES-SHA, }â
Crypto Map: "set" interfaces: { }â -
Crypto map has incomplete entries message
I'm working on building a configuration on a 5540 running 9.1.2 for L2L VPN. When I reload the device, I get this message:
.WARNING: crypto map has incomplete entries
*** Output from config line 10665, "crypto map L2LVPN interf..."
I seems it's giving me the error on the line where the crypto map is assigned to the outside interface. Unfortunately this message really is not very helpful. I do not have this in production yet. Is there any way I can find out where my problem may be?
Thanks.
JasonHi,
This usually indicates that one L2L VPN connection Crypto Map configuration is missing some essential parameter to make it complete.
So issue the command
show run crypto map
Then make sure that the following lines exists
crypto map match address
crypto map set peer
crypto map set ikev1 transform-set
If any of the 3 things mentioned above are missing then the crypto map configuration is deemed incomplete and doesnt have the information needed for that L2L VPN to function.
Atleast this is what it seems to me.
Hope it helps
- Jouni -
Crypto map entry is incomplete
Hi
This is my config below. The error i am recieving is crypto map entry is incomplete. Can someone please take a look and let me know. Thank you
ASA(config)# crypto map outside_map 1 match address outside_1_cryptomap
WARNING: The crypto map entry is incomplete!
ASA(config)# show run
: Saved
ASA Version 8.4(4)1
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.10.10.2 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network net-local
subnet 10.10.10.20 255.255.255.0
object network net-remote
subnet 10.10.3.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 10.10.10.20 255.255.255.0 10.
10.3.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (any,any) source static net-local net-local destination static net-remote ne
t-remote
object network obj_any
nat (inside,outside) dynamic interface
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 96.145.68.82
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd auto_config outside
dhcpd address 10.10.10.22-10.10.10.231 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
tunnel-group 81.141.29.69 type ipsec-l2l
tunnel-group 81.141.29.69 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:c2b7cdae5eb0961d822f634f2b36d3dc
: end
ASA(config)#Hi,
You lack a "transform-set" configuration from the "crypto map" line.
For example
Create the IKEv1 Transform set
crypto ipsec ikev1 transform-set AES esp-aes esp-sha-hmac
and
Use it in the VPN configuration
crypto map outside_map 1 set ikev1 transform-set AES
The values ofcourse depend on the your own preference
Hope this helps
- Jouni -
We've noticed a very strange issue on our Cisco 3800 router.
The router is hosting multiple Site to Site VPN connections. All of the VPNs are working fine.
While doing some routine diagnostigs we've noticed that one of the VPN's crypto maps is not displayed correctrly as you can see in the image below.
I checked the associated ACL and the last entry is displayed correctly.
I also tried to recreate the acl to see if that will fix this.
Only this crypto map is displayed like this. All of the other are displaing just fine.
I noticed that if I remove the last statement from the ACL then the crypto map will be displayed correctly.
What could be the reason for this phenomenon?
Can this cause any connectivity issues in the future?Access-lists, FW (ZBF, CBAC) and all other features work on SVTI same way they would work on a physical or other logical interfaces (with very few exceptions).
-
I have PIX 515 and trying to add a gateway to gateway VPN tunnel with dynamic IP. I already have two other VPN tunnels configured with static IP. I enter the access-list 110 than the crypto map mymap 20 ipsec-isakmp no problem. than the crypto map mymap 20 match address 101 I get error message Crypto map incomplete. Why am I getting this error and how do I get around it. Thanks.
Yes I have an Incomplete.
crypto ipsec transform-set tr-set esp-des esp-md5-hmac
crypto dynamic-map dynmap 10 set transform-set tr-set
crypto dynamic-map dynmap 15 set transform-set tr-set
crypto dynamic-map dynmap 15 set security-association lifetime seconds 3600 kilo
bytes 4608000
crypto map mymap 10 ipsec-isakmp
crypto map mymap 10 match address 101
crypto map mymap 10 set peer 70.106.123.11
crypto map mymap 10 set transform-set tr-set
crypto map mymap 15 ipsec-isakmp
crypto map mymap 15 match address 105
crypto map mymap 15 set peer 67.100.146.217
crypto map mymap 15 set transform-set tr-set
crypto map mymap 20 ipsec-isakmp
! Incomplete
crypto map mymap 6335 ipsec-isakmp dynamic dynmap
crypto map mymap interface outside -
When I use Craigslist, my personal list of things being sold, and I try and renew my listings, I periodically get this: "Warning! Domain mapping upgrade for this domain not found. Please log in and go to the Domains Upgrades page of your blog to use this domain." Usually rebooting my computer makes it go away for a short time, but today that isn't working and following the commands on the warning doesn't work either...is this truly a firefox issue? How do I fix it.
Clear the cache and the cookies from websites that cause problems.
"Clear the Cache":
*Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
"Remove Cookies" from sites causing problems:
*Firefox/Tools > Options > Privacy > Cookies: "Show Cookies" -
IPSec VRF Aware (Crypto Map)
Hello!
I have some problem with configuring vrf aware Ipsec (Crypto Map).
Any traffic (from subnet 10.6.6.248/29) do not pass trouth router, but if i run command "ping vrf inside 10.5.5.1 source gi 0/1.737" it working well.
Configuration below:
ip vrf outside
rd 1:1
ip vrf inside
rd 2:2
track 10 ip sla 10 reachability
ip sla schedule 10 life forever start-time now
crypto keyring outside vrf outside
pre-shared-key address 10.10.10.100 key XXXXXX
crypto isakmp policy 20
encr aes 256
authentication pre-share
group 2
crypto isakmp invalid-spi-recovery
crypto isakmp keepalive 10 periodic
crypto isakmp profile AS_outside
vrf inside
keyring outside
match identity address 10.10.10.100 255.255.255.255 outside
isakmp authorization list default
crypto ipsec transform-set ESP-AESesp-aes 256 esp-sha-hmac
mode tunnel
crypto ipsec df-bit clear
crypto map outside 10 ipsec-isakmp
set peer 10.10.10.100
set security-association idle-time 3600
set transform-set ESP-AES
set pfs group2
set isakmp-profile AS_outside
match address inside_access
ip route vrf inside 10.5.5.0 255.255.255.0 GigabitEthernet0/0.806 10.10.10.100 track 10
ip access-list extended inside_access
permit ip 10.6.6.248 0.0.0.7 10.5.5.0 0.0.0.255
icmp-echo 10.10.10.100 source-interface GigabitEthernet0/0.806
vrf outside
interface GigabitEthernet0/0.806
ip vrf forwarding outside
ip address 10.10.10.101 255.255.255.0
crypto-map outside
interface GigabitEthernet0/1.737
ip vrf forwarding inside
ip address 10.6.6.252 255.255.255.248Hello Frank!
>> 1. You may want to consider removing the "track 10" from your static route to eliminate any issues that this could be causing.
I tried it before. Nothing changes.
>> 2. If you teardown the tunnel, can the traffic from your end client (not the ping generated locally) cause the tunnel to build? If not, you may want to use netflow or ACL counters to verify that your packets are hitting the inside interface.
It is also checked. netflow present counters and ACL counters not present. Source ip is 10.6.6.254/29.
show command below:
ISR-vpn-1#show ip cef vrf inside exact-route 10.6.6.254 10.5.5.1
10.6.6.254 -> 10.5.5.1 => IP adj out of GigabitEthernet0/0.806, addr 10.10.10.100 (incomplete)
ISR-vpn-1#show ip cef vrf inside 10.24.1.0/24 internal
10.5.5.0/24, epoch 0, RIB[S], refcount 5, per-destination sharing
sources: RIB
feature space:
NetFlow: Origin AS 0, Peer AS 0, Mask Bits 24
ifnums:
GigabitEthernet0/0.806(24): 10.10.10.100
path 22D160E8, path list 22AC27E8, share 1/1, type attached nexthop, for IPv4
nexthop 10.10.10.100 GigabitEthernet0/0.806, adjacency IP adj out of GigabitEthernet0/0.806, addr 10.10.10.100 (incomplete)
output chain: IP adj out of GigabitEthernet0/0.806, addr 10.10.10.100 (incomplete) -
Multiple Crypto Maps on Single Outside Interface
Hi, I had the following crypto map configured on my ASA5505 to allow Cisco IPSec VPN clients to connect from the outside:
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
I'm trying now to set up an additional crypto map - a static configuration to establish a tunnel with Windows Azure services. The configuration they gave me is:
crypto map azure-crypto-map 10 match address azure-vpn-acl
crypto map azure-crypto-map 10 set peer XXX.XXX.XXX.XXX (obfuscated)
crypto map azure-crypto-map 10 set transform-set azure-ipsec-proposal-set
crypto map azure-crypto-map interface outside
However, when I apply that configuration, my Cisco IPSec clients can no longer connect. I believe my problem is that last line:
crypto map azure-crypto-map interface outside
which blows away my original line:
crypto map outside_map interface outside
It seems I'm stuck with picking just one of the maps to apply to the outside interface. Is there a way to apply both of these maps to the outside interface to allow both IPSec tunnels to be created? We're running ASA version 8.4(7)3.Hi,
You can use the same "crypto map"
Just add
crypto map outside_map 10 match address azure-vpn-acl
crypto map outside_map 10 set peer XXX.XXX.XXX.XXX (obfuscated)
crypto map outside_map 10 set transform-set azure-ipsec-proposal-set
Your dynamic VPN Clients will continue to work just fine as their "crypto map" statements are with the lowest priority/order in the "crypto map" configurations (65535) and the L2L VPN is higher (10)
And what I mean with the above is that when a L2L VPN connections is formed from the remote end it will naturally match the L2L VPN configurations you have with "crypto map" configurations using the number "10". Then when a VPN Client connects it will naturally not match the number "10" specific configurations and will move to the next entry and will match it (65535)
If you would happen to configure a new L2L VPN connection then you could give it the number "11" for example and everything would still be fine.
Hope this helps
- Jouni -
Which interface does "crypto map vpn" get assigned to?
I'm setting up a site to site vpn and have been reading some examples, but my 871 uses a vlan so it confuses me a bit. Do I assign the statement crypto map vpn to the vlan1 interface or fe4 which is my WAN side.
Sander
If we knew more about your environment we might be able to give better answers. In general the crypto map is assigned to the outbound layer 3 interface. But I can not tell from your description whether fe4 or VLAN 1 is the outbound layer 3 interface. Does fe4 have an IP configured on it? If so then perhaps it is the outbound layer 3 interface and gets the crypto map. Or perhaps VLAN 1 is the outbound layer 3 interface and gets the crypto map.
If this helps you figure it out that is good. Otherwise perhaps you can provide some clarification of the environment.
HTH
Rick
Sent from Cisco Technical Support iPhone App -
Site to Site VPN working without Crypto Map (ASA 8.2(1))
Hi All,
Found a strange situation on our ASA5540 firewall :
We have couple Site to Site VPNs and also enable cleint VPN on the ASA, all are working fine. But found a Site to Site VPN is up and running without crypto map configuration. Is it possible ?
I tried to clear isa sa and clear ipsec sa then the VPN came up again. Also tested it's pingable to remote site thru the VPN.
I did see there is tunnel-group config for the VPN but didn't see any crypto map and ACL.
How does Firewall know which traffic need be encrypted to this VPN tunnel without crypto map?
Is it the bug ?
Thanks in advance,It might be an easy vpn setup.
Could you post a running config output remove any sensitive info. This could help us answer your question more exactly. -
Crypto Map on Loopback interface or Physical Interface
Dear All,
When we try to apply the crypto map on any physical interface or the loopback interface on WS-6506-E, it is showing the error. But the same i could apply on VLAN interface. Can anyone explain me what is the issue..?
6506(config)#interface loopback 3
6506(config-if)#crypto map XXXX
ERROR: Crypto Map configuration is not supported on the given interface
Any hardware limitation?This was proven to break CEF in the past and is a bad design choice by default.
Newer release do not allow you to configure this.
If you're curious if it will work for you check releases prior to 15.x.
M. -
Hi all, when doing an access list for encrypting traffic on a crypto map, what kind of access list do you use, and do you permit destination traffic to be encrypted or source ?
Carl,
Extended ACLs are used to define interesting traffic which needs to be encrypted.
access-list 101
hope this helps ... -
Crypto Map on Tunnel interface
hi guys, when i trying to apply crypto map on tunnel interface , debug is (
crypto map is configured on tunnel interface. Currently only GDOI crypto map is supported on tunnel interface )
why i can't apply simple crypto map on tunnel interface? anyone knows?
thanksThis was proven to break CEF in the past and is a bad design choice by default.
Newer release do not allow you to configure this.
If you're curious if it will work for you check releases prior to 15.x.
M. -
Can I enter crypto map command on an ethernet interface(LAN)
Hi Friends,
I am establishing VPN tunnel through Internet. I have the public address configured on Ethernet interface of router connecting the LAN. Can I bind the crypto map command to this inside interface and establish the VPN connectivity from this interface. Please help me providing the knowledge.your crypto map must be bound to outside interface.
but you can chose which ip to use
http://www.cisco.com/en/US/docs/ios/mwpdsn/command/reference/mwp_02.html#wp1014299
[Pls RATE if HELPS]
Maybe you are looking for
-
I bought a song off of the itunes store on my iphone but it wont play. I even tried to repurchase it but it says that I already purchased it. I have restarted my phone and turned it off but it still won't download or play. HELP!
-
Getting error while opening layout in mobile system maintenance
Hi Experts, I implemented note 904571 to prefilldata, with which all standard layouts loaded to mobile system maintenance. But problem here is if I try to open any one of the layout its giving following error "An unhandled exception has occured in yo
-
How do you get your tv to act as a monitor using apple tv?
Can you get your television to act as a monitor using Apple TV?
-
Apple Mail and MS Exchange server?
In a strange twist of fate, our new university President is a Mac guy (yeah!), but he is obligating all of us to put email and calendar software into MS Exchange server. Sadly, it means I will need to migrate 4 GB of emails from Apple mail to Entoura
-
Infinality-bundle-fonts: a free multilingual font collection for Arch
infinality-bundle-fonts: a free multilingual font collection for Arch Linux infinality-bundle-fonts is meant to be a complete, 'install-and-forget' solution for most (Arch) Linux users looking for easy access to common type-faces diversity needed to