Water under the screen while applying the invisible shield
I was applying the full body invisible shield and since it was difficult to apply the back(as suggested by every one) I did it one night switched the phone off all the time and the next morning it was fine and i loved it as it was looking good and on top of it it was protecting the back side of the phone.
The next night i applied the front side(supposed to be the easy side and child's play) and to my annoyance when I switched the phone back on in the morning there was water(? solution for applying the screen protector)under the screen. The screen looks awful
The ringer volume plays up now and switching on the phone is a bit cumbersome as it plays (sometimes in one go sometimes I have to use the home button and the power button together).
My phone is new ,bought on the 2nd of April 2010 and what do I do now? will apple warranty cover this?
Apple will not cover any moisture damage to the iPhone.
You can see if the moisture sensors are tripped or not. If they are then you are out of luck on warranty, no questions asked. Here is Apple's support document of inspecting the moisture sensors...
http://support.apple.com/kb/HT3302
If the sensors are not tripped, Apple would probably not cover the iPhone under warranty if there is visible signs of water (or liquid) behind the screen. If the button problems are not that bad, then you could switch the iPhone off and place in a bag of dry rice. It might help draw out some of liquid from the screen.
Personally I would stay away from anything that requires liquid to install. If done wrong it can kill the phone, which may be the case here. You can still make an appointment at an Apple store to look into an out of warranty replacement, which would get you a refurbished iPhone for a flat rate. The other option would be to check to see if there are any local third party repair centers. They may be cheaper than the out of warranty replacement, but at the same time could be more.
Similar Messages
-
How can I turn off the screen while keeping the mac awake?
I am using teamviewer to remote connect to my office Imac from home. However, every time I connected, my imac screen will turn on and everyone else in the office can see what my imac is doing..
Is there some method to turn off the screen while keeping the mac awake, so I can remote connect to it?
PS: I am using OSX 10.7.3Energy Saver, you can keep the computer awake while the screen saver shuts the monitor off but I'm not sure that would do it for you.
-
Can I turn the screen while browsing the web ?
Can I set the screen to display the web longways as aposed to narrrow ways ?
It would just make some pages look better.
N96-1 + 8G SD~Software Version 30.033~Software Version Date 18-06-09~Type RM-247~P/C 0543713~T Mobile UKNot on the N70. On, e.g., the E70 it is possible.
-
How to supress the screen while calling the Fm
hi all,
i am using a FM HRHAP_SHOW_DOUMENT,
i am passing the ADD_ON_APPLICATION = ALL
MODE = N
S_APPRAISAL_ID = my appid(50000081).
and also start date, end date,T_NEW_APPRAISER,T_NEW_APPRAISEE,
and when i execute this FM i am getting a new screen,
but when i call the FM it shud not be displayed,
is there Fm to supress the screen
please help me to go ahead.Hi rukmani,
i don't think it is possible to supress the screen by calling any other FM. as all the screens are associated wid the function module. so if u don't want that screen in that case use any other fm for the same purpose.
regards
saurabh -
Work failed while applying the patch 3480000
Dear All,
Please Help
At the phase of applying the patch 3480000 while upgrading from 11.58 to 11.5.10.2
workers failed:
FAILED: file WFXLoad.class on worker 5 for product fnd username APPLSYS.
Time is: Tue Apr 05 2011 06:30:13
ATTENTION: All workers either have failed or are waiting:
FAILED: file WFXLoad.class on worker 1.
FAILED: file WFXLoad.class on worker 2.
FAILED: file WFXLoad.class on worker 3.
FAILED: file WFXLoad.class on worker 4.
FAILED: file WFXLoad.class on worker 5.
FAILED: file WFXLoad.class on worker 6.
FAILED: file WFXLoad.class on worker 7.
FAILED: file WFXLoad.class on worker 8.
ATTENTION: Please fix the above failed worker(s) so the manager can continue.Hi Hussein,
Sorry for being late
next is output screen for patch 3480000
There are now 39641 jobs remaining (current phase=A84):
6 running, 216 ready to run and 39419 waiting.
Assigned: file WFXLoad.class on worker 7 for product fnd username APPLSYS.
Assigned: file WFXLoad.class on worker 8 for product fnd username APPLSYS.
FAILED: file WFXLoad.class on worker 4 for product fnd username APPLSYS.
FAILED: file WFXLoad.class on worker 1 for product fnd username APPLSYS.
FAILED: file WFXLoad.class on worker 3 for product fnd username APPLSYS.
FAILED: file WFXLoad.class on worker 6 for product fnd username APPLSYS.
FAILED: file WFXLoad.class on worker 8 for product fnd username APPLSYS.
FAILED: file WFXLoad.class on worker 2 for product fnd username APPLSYS.
FAILED: file WFXLoad.class on worker 7 for product fnd username APPLSYS.
FAILED: file WFXLoad.class on worker 5 for product fnd username APPLSYS.
ATTENTION: All workers either have failed or are waiting:
FAILED: file WFXLoad.class on worker 1.
FAILED: file WFXLoad.class on worker 2.
FAILED: file WFXLoad.class on worker 3.
FAILED: file WFXLoad.class on worker 4.
FAILED: file WFXLoad.class on worker 5.
FAILED: file WFXLoad.class on worker 6.
FAILED: file WFXLoad.class on worker 7.
FAILED: file WFXLoad.class on worker 8.
ATTENTION: Please fix the above failed worker(s) so the manager can continue.
next is last lines in adworker log file
adjava -mx256m -nojit oracle.apps.fnd.wf.WFXLoad -u &un_apps &pw_apps &jdbc_db_addr &jdbc_protocol US &fullpath_cln_patch/115/xml/US_cln2a12os.wfx
Error:
Program exited with status 1
Cause: The program terminated, returning status code 1.
Action: Check your installation manual for the meaning of this code on this operating system.
Copyright (c) 2002 Oracle Corporation
Redwood Shores, California, USA
AD Java
Version 11.5.0
NOTE: You may not use this utility for custom development
unless you have written permission from Oracle Corporation.
Reading product information from file...
Reading language and territory information from file...
Reading language information from applUS.txt ...
Temporarily resetting CLASSPATH to:
"h:\oracle\prodappl\ad\11.5.0\java\adjri.zip;H:\oracle\prodcomn\util\java\1.3\jdk1.3.1_07\lib\rt.jar;H:\oracle\prodcomn\util\java\1.3\jdk1.3.1_07\lib\i18n.jar;h:\oracle\prodcomn\java\appsborg.zip;h:\oracle\prodora\8.0.6\forms60\java;h:\oracle\prodcomn\java"
Calling h:\oracle\prodora\8.0.6\jdk\bin\java.exe ...
Oracle Workflow XML Loader 2.6.2
Connecting to APPS@(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=NT4SERVER)(PORT=1521))(CONNECT_DATA=(SID=PROD))) -- UTF8
Connected to (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=NT4SERVER)(PORT=1521))(CONNECT_DATA=(SID=PROD)))
SQL Exception encountered during upload: ORA-06550: line 1, column 7:
PLS-00306: wrong number or types of arguments in call to 'UPLOADOBJECT'
ORA-06550: line 1, column 7:
PL/SQL: Statement ignored
Fatal error encountered during upload between line 10 and 35
Error encountered when upload.
AD Run Java Command is complete.
AD Worker error:
The above program failed. See the error messages listed
above, if any, or see the log and output files for the program.
Time when worker failed: Tue Apr 05 2011 06:30:13
Thanks&BR
Tarek -
My iPod nano will go into the sleep mode while a song is playing a second after the screen goes blank; the song will stop and I will then have to press the sleep/awake button to pick up where the song left off. How do I fix this?
Your problem is that your iPod is not sensing that your headset is inserted. There is a pin inside the headphone port on the Nano that senses if it is inserted fully. If it does not sense anything, it will pause playback to save battery power when the screen dims. Here are the solutions:
Insert it fully. This will fix it for most of you. Press that thing in there all the way. You should feel and hear a full click when it is fully seated. If you can see ANY silver of the headset jack, it is not fully inserted.
Debris inside the headset port. If you are totally unable to push the headset jack all the way, the most likely problem is that you have crud inside your headphone jack. Try blowing it out or slapping it against your palm with the headset port facing your palm to try and get the stuff out. If you look into he jack with a light, you should be able to see to the bottom. The entire inside of the headset port is white, so if it looks dark at the bottom, that is the crud that is keeping your nano from working.
Headset jack or plug issue. If you cannot solve the problem with 1 or 2, then there is likely something physically wrong with either the headset jack on your headphones or the headset port on the nano.
If none of the above works, you need to take it to the Apple store or wherever you purchased it. I think they are still under warranty.
i -
Error : While applying the Patch 4440000
Error : While applying the Patch 4440000
FAILED: file igwprop.odf on worker 1 for product igw username IGW.
When i check the worker log file i got this error
The sequence IGW_AWARDS_S in the database is defined as:
MINVALUE = 1 MAXVALUE = 2147483647 INCREMENT BY = 1
CYCLE = NO ORDER = NO CACHE = 1000
which should be defined as:
MINVALUE = 10000 MAXVALUE = 2147483647 INCREMENT BY = 1
CYCLE = NO ORDER = NO CACHE = 1000
(Note: The cache value for sequence IGW_AWARDS_S is 20 in the ODF file. The value 1000 is being used instead because this provides better performance when selecting from the sequence.)
Alter the sequence with :
Start time for statement below is: Sun Oct 06 2013 22:16:28
ALTER SEQUENCE IGW.IGW_AWARDS_S MINVALUE 10000
AD Worker error:
The following ORACLE error:
ORA-04007: MINVALUE cannot be made to exceed the current value
occurred while executing the SQL statement:
ALTER SEQUENCE IGW.IGW_AWARDS_S MINVALUE 10000
AD Worker error:
Unable to compare or correct sequences
because of the error above
Time when worker failed: Sun Oct 06 2013 22:16:28
plz help me in solving this.Check the current value of IGW_AWARDS_S sequence and make sure the MINVALUE in the patch (i.e. 10000) is not greater than the current one.
OERR: ORA 4007 MINVALUE cannot be made to exceed the current value (Doc ID 19824.1)
You may also log a SR.
Thanks,
Hussein -
Looking for an App to Lock the Screen while Playing a Movie
I've been looking for either an app to lock the screen (not turn the screen off like the button on top of the phone) while playing a movie or a media player that will prohibit you from pressing buttons while a movie is playing. The reason I'm looking for this is my son likes to watch movies on my iPhone while we're in the grocery store, but I spend more time restarting the movie or navigating back to the iPod app and restarting the movie than he spends watching it! He likes to press the "done" button or home button which ends the movie. So an app that would prohibit that would be GREAT, but I haven't been able to find one so far. Any suggestions?
An app will not be able to do this.
Sorry. -
Error While applying the maintenance pack12.1.1
Hi All,
While upgradeing the applications from12.0.4 to 12.1.1 ,While applying the maintenance pack patch(7303030) iahave encountered the below error
worker failed with the below Error
sqlplus -s APPS/***** @/oracle/AMALCRP/apps/apps_st/appl/zx/12.0.0/patch/115/sql/zxmigratefc.sql
DECLARE
ERROR at line 1:
ORA-01422: exact fetch returns more than requested number of rows
ORA-06512: at "APPS.ZX_FC_MIGRATE_PKG", line 386
ORA-06512: at "APPS.ZX_FC_MIGRATE_PKG", line 978
ORA-06512: at "APPS.ZX_FC_MIGRATE_PKG", line 5017
ORA-06512: at line 6
Please let me know if ther is any possible solution for this
Thanks iN Advance
SagiFor the first Error
Sol:1. Download patch 8593634:R12.ZX.B and unzip the patch to a temoprary folder.
2. Backup the file $ZX_TOP/patch/115/sql/zxfcmigrateb.pls
cp $ZX_TOP/patch/115/sql/zxfcmigrateb.pls $ZX_TOP/patch/115/sql/zxfcmigrateb.pls-BKP
3. Copy the file zxfcmigrateb.pls from the patch location (/<PatchUnzipLocation>/zx/patch/115/sql/zxfcmigrateb.pls) to $ZX_TOP/patch/115/sql/zxfcmigrateb.pls
4. Execute the newly copied file using SQLPLUS:
sqlplus apps/<apps password>
SQL> @ $ZX_TOP/patch/115/sql/zxfcmigrateb.pls
5. Now re-start the failed worker for patch
Next i got the Error which is mentionedin the note 1299350.1
Sol:
1. Download patch 10250232:R12.ZX.A and unzip the patch to a temoprary folder.
2. Backup the file $ZX_TOP/patch/115/sql/zxfcmigrateb.pls
cp $ZX_TOP/patch/115/sql/zxfcmigrateb.pls $ZX_TOP/patch/115/sql/zxfcmigrateb.pls-BKP
3.
Copy the file zxfcmigrateb.pls from the patch location
(/<PatchUnzipLocation>/zx/patch/115/sql/zxfcmigrateb.pls) to
$ZX_TOP/patch/115/sql/zxfcmigrateb.pls
4. Execute the newly copied file using SQLPLUS:
sqlplus apps/<apps password>
SQL> @ $ZX_TOP/patch/115/sql/zxfcmigrateb.pls
5. Now re-start the failed worker for patch
But Theses patches require passcode which we getonly by logging an SR
Thanks
Vinay Varma -
Error while applying the Service Policy
Hi,
I am getting the below error while applying the service policy to the Interface.
I have set the mpls exp 4 as well as want to limit the bandwidth to 1Mbps
PE#sh policy-map setexp-GBoIP
Policy Map setexp-GBoIP
Class GBoIP-traffic
set mpls experimental imposition 4
police cir 1024000 bc 32000
conform-action transmit
exceed-action drop
PE(config-if)#int vlan 2007
PE(config-if)#service-policy input setexp-GBoIP
QoS-ERROR: Addition/Modification made to policymap setexp-GBoIP and class GBoIP-traffic is not valid, command is rejected
As well as I have created new clas--map with priority and Bandwidth and applied in output direction, I got the belwo error while applying the Service policy in
PE(config-if)#service-policy out TEST
bandwidth command is not supported in output direction for this interface
PE(config-if)#service-policy output TEST
priority command is not supported in output direction for this interface
Any idea why so ?
Thanks in Advance.
Regards,
NileshCheck the current value of IGW_AWARDS_S sequence and make sure the MINVALUE in the patch (i.e. 10000) is not greater than the current one.
OERR: ORA 4007 MINVALUE cannot be made to exceed the current value (Doc ID 19824.1)
You may also log a SR.
Thanks,
Hussein -
While applying the patch 10270433
While applying the patch 10270433 i got this error
The fix for Patch 7426842, are included in the patch currently
being installed (10270433)
Patch(es) 7140405, 8602992, conflict with the patch currently
being installed (10270433)
If you continue, all patches will be rolled back and the new patch
(10270433) will be installed.
Note: If the patch currently being installed (10270433) is rolled back,
it is recommended that the fixes being rolled back here (7426842, 7140405, 8602992, ) are reinstalledThe fix for Patch 7426842, are included in the patch currently
being installed (10270433)This is not an error message so you can ignore it.
Patch(es) 7140405, 8602992, conflict with the patch currently
being installed (10270433)
If you continue, all patches will be rolled back and the new patch
(10270433) will be installed.
Just apply Patch 10270433 and this will rollback other patches -- Please make sure you take a backup before applying this patch.
Thanks,
Hussein -
While applying the patch getting an error Failed:xdoloader.class on worker
Hi,
While applying the patch getting an error Failed:xdoloader.class on workerWhile applying the patch getting an error Failed:xdoloader.class on workerPlease post the details of the application release, database version and OS.
What is the patch number you are trying to apply?
Please post the complete error message from adpatch log file.
Thanks,
Hussein -
I recently got a an iPod 5 generation as a gift and while I was in my settings I turned on the voice over to check the percentage of my battery, so I turned it off and now I can't unlock it. Even when scrolled my fingers on the screen and typed the password but it would unlock, please can some one help me with this
You have the accessibility VoiceOver feature turned on.
Triple click the home button and try going to Settings>General>Accessibility and turn VoiceOver off. You may have to use three fingers to scroll the screen to get there. If problems see the following for how to turn off via iTunes:
iPhone: Configuring accessibility features (including VoiceOver and Zoom) -
How to Fill the selection screen while calling the transaction
Hi All,
my requirement is in one of the screen while i will press a push button it will call one transaction and it will fill the selection screen build order number field and skip the first screen i.e the selection screen it will show the output of that report directly.
am using this code .
case sy-ucomm.
while 'FSLR'.
set PARAMETER ID 'ANR' FIELD aufnr.
RANGES s_aufnr FOR afko-aufnr.
s_aufnr-sign = 'I'.
s_aufnr-option = 'EQ'.
s_aufnr-low = aufnr.
APPEND s_aufnr.
CALL TRANSACTION 'ZFS1' USING s_aufnr
MODE 'E' .
AND SKIP FIRST SCREEN.
endcase.
here the problem is i cant use both skip screen and using at a time nither the screen is filling nor its skipping the first screen.
but its not working would any one please help how can i do this functionality?Hi
Do in this way.
DATA: rspar TYPE TABLE OF rsparams WITH HEADER LINE.
rspar-selname = 'S_AUFNR'.
rspar-kind = 'S'.
rspar-sign = 'I'.
rspar-option = 'EQ'.
rspar-low = 'aufnr'.
APPEND rspar.
SUBMIT zfs1_prog VIA SELECTION-SCREEN WITH SELECTION-TABLE rspar AND RETURN.
If this doesnt suit yer requirement, I wud suggest you to use BDC as below.
CALL TRANSACTION 'SE11' USING bdcdata
MODE 'E'
UPDATE 'A'. -
How do I view a website over the full screen while using the 6 plus in horizontal mode
How do I view a website over the full screen while using the iPhone 6 plus in horizontal mod?
You said you found several domain.sites files.
iWeb uses one at a time to create webpages.
Your webpages, your site, has disappeared with MobileMe.
You have to find a new host and publish there.
But to publish you need one of your domain files.
Try iWebSites to open them :
http://www.wyodor.net/_Demo/Aptana/iWebSites.html
Maybe you are looking for
-
Partitioning previously used Windows NT File System for use with Mac and PC
With reference to this thread I found when searching for a solution: Can Windows NT File System(NTFS) format external hard drive work on iMac? Below is the comment which led to me creating this new thread. "rkaufmann87Sep 8, 2014 8:26 AM Re: Can Wind
-
How to get column type as a string
I want to create a table dynamically based on some other table definition but not exactly same. Is there a way I can get the column types as strings so I can create a sql statement for creating the table. 'create table tmp_account( col1 typecol3, col
-
I'm trying to find some way to recreate the type of news box used on www.msn.box where photos and related teaser text fade in. I'd like it to pull txt and photos from external files instead of hard coding. is that possible? How do I get started?
-
One question about dreamweaver cc layers
Hello! Help please, how create a new layer with text over pictures? *Only In dreamweaver 13 cc! Thanks
-
Dynamically Update External Table Data
I loaded a data table from an external csv file. But the csv file is an output from a program that appends a new line to the csv file every couple days. I made a Report with the loaded data, but in a couple days when a few new lines of data appear in