Wath is true network setting for webscan with crossover cable?

hello everyone
i have a problem with webscan.
i have two desktop computer that are networked with a "crossover cable" . one of these computer have two network port that i connect my hp 6500 all in on with another "crossover cable" to to another network port of this computer.
my ip setting in computer "1" with two network port:
192.168.0.1 =====> for connect to another computer
169.254.199.1 =====> for connect to hp 6500
my ip setting in computer "2" with one network port:
192.168.0.2
my ip setting in hp 6500:
169.254.199.140
computer 1 can find computer 2 and hp 6500. and computer 2 can find computer 1 but the problem is here that "the computer "2" can't find hp 6500".
please help .
if my network setting is wrong, what's it's right.
note: both of my os is windows xp.
i apologize for my poor English.
This question was solved.
View Solution.

Have you tried manually configuring the printer IP to 192.168.0.3?
You would also need to put the printer's subnet mask at 255.255.255.0
That should allow computer 1 to route printer IP packets to computer 2 (as long as computer 1 is turned on and computer 1 provides routing between the ethernet ports).
It's worth a try.
Please mark the post that solves your problem as "Accepted Solution"
Sometimes it takes several posts back and forth to get to a solution - please be patient.
I am employed by HP

Similar Messages

What is best network setting for jetpack mifi 5510l

I live in a rural area with poor signal. No 4G and limited 3G. We got an antenna that boosts phones from nothing or 1X one bar to 3G and 2-3 bars inside the house. What is the best network setting for jetpack? It doesn't seem to work as well.
Automatic and 4g don't work. I don't know what CDMA Auto or EDVO stand for.
Any suggestions for improving strength would be appreciated. I know I won't get a great connection but a steady connection sure would be great.

> What is the best network setting for jetpack?
Not sure what you mean. The jetpack will automatically configure itself to whatever signal it currently has access to. Shouldn't have to configure any network settings.
> I don't know what CDMA Auto or EDVO stand for.
Those are the old 3G networks.
> Any suggestions for improving strength would be appreciated.
Perform what is known as a Site Survey and evaluate your current environment:
http://3gstore.com/page/13_will_an_antenna_help_me.html
After you generate some numbers then look up what they mean in the Interpret the Results tab. You mentioned that you already purchased an antenna so there may not be anything else you can do as the local towers in your area are not good enough to reach inside your home.

How does one install non-English character sets for use with the "find" function in Acrabat Pro 11?

I have pdf files in European languages and want to be able to enter non-English characters in the "find" function. How does one install other character sets for use with Acrobat Pro XI?

Have you tried applying the update by going to Help>Updates within Photoshop Lightroom? The update should be using the same licensing? Did you perhaps customize the installation location? Finally which operating system are you using?

Hi.. i've got problem with my iPhone 4s gsm factory unlocked it won't connect to a wifi. i tried to hold power and home button even reset the network setting but ended with i am not able even to turn the wifi on. does any body can help me out???

hi..
i've got problem with my iphone 4s gsm factory unlocked it won't connect to a wifi. i tried to hold the power and home button even reset the network setting but ended with i am not even can turn the wifi on. does any body can helpme?

See this: http://support.apple.com/kb/TS1559
If you carefully follow all of the instructions in this tip and none of them restore WiFi then your radio chip has failed and you need to get the phone replaced by Apple.

My iphone 5 is problem facing like that. when i switch off my iphone5 then plugh for charge with data cable or charger adapder or only data cable with no power connect phone is starting why? means on my phone Why? any one can explane this matter please. s

my iphone 5 is problem facing like that. when i switch off my iphone5 then plugh for charge with data cable or charger adapder or only data cable with no power connect phone is starting why? means on my phone Why? any one can explane this matter please. switched off my phone but on without power button . what is the problem?
Thanks
s.m slim

all iphone is same like that

Network emulator for Linux with a good gui?

Hi all,
At work I use NEWT (Network Emulator Toolkit for Windows) http://blog.mrpol.nl/2010/01/14/network … r-toolkit/ in conjunction with a packet capture tool. I would like to see if I can use Linux instead; I will use Wireshark for packet capturing/analysing, but I need an equivalent GUI tool to replace NEWT. What NEWT does for me: block ports, ip ranges, throttle bandwidth, etc.
From searching I found netem, but I can't find an actively developed gui for it. Does anyone know what I can use?
Thanks.

wrm wrote:EDIT: Take a look at https://wiki.archlinux.org/index.php/Fi … _frontends
Thanks! I should've thought of looking at the Firewalls wiki page; it didn't cross my mind that there would network shaping tools there. Looks like I should be covered with any luck!
I think Shorewall/Vuurmuur could replace NEWT, and then I'd use Wireshark on the side for the packet analysing. I see Shorewall has a webmin config tool, which would be great for others to learn.

Best sequence setting for use with images?

Hey all.
I'll be working on a project that will be dealing with mostly images. I have them in their original RAW format as well as jpgs. After messing around in Final Cut with the images, I've noticed that the Viewer will display the image crisp and clear and once displayed on the Canvas window, the image is slightly blurred and the quality is decreased slightly which I'm assuming is because of sequence setting? Basically I'm wondering what my settings should be to produce the highest quality images when displayed in a quicktime movie when I export it.
Examples of high quality images in a quicktime movie of what I'm looking for:
http://vimeo.com/7070015
Any input would be appreciated.
-Neil

a project that will be dealing with mostly images...
And what will the other stuff be, video? What format?
The viewer always presents the image as is. When you place it on the Timeline, it takes on the attributes of the Sequence setting.
Your images might be 4000x3000 pixels, but that's not a video standard. Blowing up any video to those pixel dimensions will make it look awful.

Mime type note set for css with wwv_flow_file_mgr.get_file

Hello,
We have an apex application over here that has problems with the mime type of a theme (css) file. The css file works correctly in IE but not in FF or Chrome (because IE check the file extension, but FF seems not do not ..).
This is the call that is failing
<link type="text/css" rel="stylesheet" href="wwv_flow_file_mgr.get_file?p_security_group_id=33490830277084435&p_fname=theme_3_1.css" />
in the FF error console it complains about the file being of application/octet-stream instead of text/css and therefore it will not load it.
I have created a simple local .htm file with
<html>
<link type="text/css" rel="stylesheet" href="http://xxx.xxx.xx/pls/htmldb/wwv_flow_file_mgr.get_file?p_security_group_id=33490830277084435&p_fname=theme_3_1.css" />
</html>
And it loads the file (even though it says it is still application/octet-stream) in FF, but it will not do the same if called from Apex.
I'm kind of lost here, so any ideas where to look for an explanation/fix ? (Yes, we have the AddType text/css .css in the httpd.conf)
regards.

Hi UserXY,
what connectivity module do you use (Oracle HTTP Server, Embedded PL/SQL Gateway, APEX Listener)?
Which Browser did you use to upload the css-File?
I don't know why this happend in your case, but you could try a different browser to upload the file again.
brgds,
Peter
Blog: http://www.oracle-and-apex.com
ApexLib: http://apexlib.oracleapex.info
Work: http://www.click-click.at

What is the outgoing server setting for bluehost with iphone4

I can receive but not send emails from my iphone 4 from my bluehost account. I set it up using my box number as I read somewhere to do and that allowed me to receive, but I cannot send. boxXXX.bluehost.com
Any ideas?

When working with 3rd party providers you need to check with them:
http://tutorials.bluehost.com/iphone/ <--- has a step by step video

Anamorphic setting for livetype with pall footage

Hi all.
Ive shot a project on squeeze mode (anamorphic) on my HVX200 and want to make my livetype project the same. How do i do that?

I assume you mean PAL footage rather than Pall footage. The pall footage definitely loses effectiveness
In Project Properties, set up for CCIR PAL 5:4 then change the pixel aspect ratio setting to 1.42.

Initial Set Up Problem With Included Cable

As I excitedly unpacked my new ipad yesterday and cut it on I got the connect to itunes alert on the screen which I expected. When I made the connection with the included cable to my laptop and activated itunes nothing happened, itunes never recognized the ipad and cutting the ipad on off just continued to show the connect to itunes alert. I was beginning to panic a little at that point. Tried closing and reopening itunes, rebooting the computer, rebooting the ipad. Nothing worked. Then I tried that reset method of holding down the sleep/wake and home buttons down until the Apple symbol comes up. Apparently doing it the way I did put it in recovery mode which for some reason itunes recognized and went through the laborious process of downloading the software and preforming a restore.
I wasn't happy about that but at least itunes finally "saw" the ipad. So after it went through that process a message came up that the restore was being verified with Apple. After several minutes of that got a message that restore had failed. Now I was really panicked and tried to do the same all over again hoping that it would work. Well it didn't work, kept coming back to the failed message and essentially now I had a brick. I calmed down a little and went online to make an appointment with the genius bar of a local Apple store for this morning. Out of curiosity and as a last resort I tried one of my iphone cables and right away I noticed something. Whenever you connect an ipod touch, iphone or ipad to a charger you get that little audible sound that I call a trill. Well I heard that right away when I used the iphone cable which made me realize that I had not heard that on any of my previous attempts. iTunes saw the ipad, went through the activation process and everything set up fine afterwards. I cancelled the genius bar appointment.
I thought I would post this just in case others may run into the same problem. By the way my wifi has worked perfectly so far with no connection issues. Don't know when or if I will set up the 3G access.

Thanks for the suggestion but I did purchase Applecare as well so I shouldn't have any problem if there is an issue. And I probably will check out 3G at some point but for now there are no issues at all, no wifi connection issues, no drops coming out of sleep, no weak or slow connections. Nothing like what I've read in these other threads so I don't really expect any 3G problems.

How to connect my laptop to tata sky set top box with HDMI cable

piease tell me how

Hi, Your laptop has HDMI OUT and your settop box ALSO has HOMI out, you can't connect two OUT ports together, this won'twork. Is this the one ? http://www.honeytechblog.com/tata-sky-plus-hd/ Regards.

Oracle RAC and crossover cable for private network

Hi,
I have the following configuration: two database servers, each has four network cards, two for public network and two for private, cluster network. Each public card has own IP-address and both have virtual IP-address, defined in operation system (SLES-9) for redundancy. Because I have only two machines in the cluster I want to connect the two machines for private with crossover cable without switch. For redundancy I want to make two connections between machines. Is it at all possible? How should I defined all network interfaces and what should be included in /etc/hosts for properly work of Oracle cluster?
Best Regards,
Jacek

Hi,
You can build a RAC witch CROSSOVER, but the Oracle no homolog.
As you have 4 cards, 2 to public (redundancy) and 2 to interconnect (redundancy) you need of a software to to make a TEAM, and create a card virtual that will have a IP address.
Eder

Multi-user, networked set-up for Macs - ideas wanted!

Let me say at the outset that my preference would be to wait for the new Mac Pro Towers to come out. Having said that, however, I'm looking for some ideas on setting up some sort of network environment for editing with either iMacs or Mac Minis.
I run a University Lab with 4 student work stations and 3 office editing suites. All are connected to the network via gigabit. In the past, we successfully used the FCP Server as an edit-in-place device. Well... it was successful at *that* anyway We shoot long-format, multicam, HD AVCHD (and we want to edit it natively). Typically 4 or 5 two-camera, hour long shoots a week. We also do occassional P2 work (2 or 3 camera shoots), DSLR (short pieces) and several three-camera (or more) multicam theater productions (2-4 hours each - AVCHD).
Does anyone have recommendations for a fast and reliable network solution (ideally over ethernet unless Thunderbolt would be a better solution) that would support, say, 4 simultaneous editors? For the moment, let's say price is not as much of an issue as speed and reliablility. I already have a 16TB network for medium-term storage of finished archived pieces and raw footage. I'm looking for something smaller (4 TB), for working projects over the course of a semester. TPTB would like to have it stored in the Server Room (which is why I said Ethernet over Thunderbolt).
As to computers... I'm no fan of iMacs (I prefer Minis) but the highest end one seems to have an Adobe supported graphics card. As far as I can tell the minis don't. Both iMacs and Minis have Thunderbolt but I really **really** don't want the nightmare of multiple external harddrives (been there, done that, hated it!). Does anyone have experience using Premiere on either a mini or iMac?
Any other thoughts would be greatly appreciated. This isn't the route I want to go, but the money is available now and the new Mac Towers are not.
Thanks
Allynn

I have NO idea if these "exact problems" pertain to Macs, since I think most of these discussions are about Windows... but, some reading (not all PPro, but I put all the links I have saved, just for general information)
-see #3 http://forums.adobe.com/thread/771151
-you may NOT "map" your My Documents folder to a network drive
-you MUST give all users administrator accounts to use Premiere
-and especially Encore dual layer http://forums.adobe.com/thread/969395
-#5 Server 2008 is UNsupported http://forums.adobe.com/thread/851602
-a work around, of sorts http://forums.adobe.com/thread/957523
-and not on a "domain" http://forums.adobe.com/thread/858977
-also PreEl see #5 http://forums.adobe.com/thread/1017199
-more PreEl problem http://forums.adobe.com/thread/975117
The solution... some day... may be at this link
Adobe Anywhere http://www.adobe.com/products/adobeanywhere.html

I have problem with my wifi in 4 S, i cant connect to any wifi itried resetting network setting and reset all setting but the result was the same, its only keeps searching for wifi and cant find any, itried to use OTHER but also didnt work.please help me

i have problem with my wifi in 4 S, i cant connect to any wifi itried resetting network setting and reset all setting but the result was the same, its only keeps searching for wifi and cant find any, itried to use OTHER but also didnt work.please help me???

If Join was on then your home wi-fi must be set to Non-Broadcast. If you did not set this up (maybe your provider did) then you will need to find the Network Name they used, and any password they used. The SSID is Security Set ID and to see more try http://en.wikipedia.org/wiki/SSID . Basically it is the name used to identify your router/network. A lot of times the installer will leave it set as LinkSys, or Broadcom or whatever the manufacturer set it as for default. Your best bet is to get whoever installed it to walk you through how they set it up, giving you id's and passwords so you can get in. HOWEVER, if you are not comfortable with this (if you set security wrong, etc.) you would be well ahead of the game to hire a local computer tech (networking) to get this working for you. You can also contact the vendor of your router and get help (if it is still in warranty), or at least get copies of the manuals as pdf files. Sorry I can't give you more help, I hope this gives you an idea where to go from here to find more.

Wath is true network setting for webscan with crossover cable?

Similar Messages

Maybe you are looking for