Wave Form Chart'ın X eksenini encoder verisine bağlamak

İlk türkçe konumu açmaktan büyük mutluluk duyarım
Elimdeki encoder verisini ,üretmiş olduğumun numeric sayısal değerlerle eşleyip chartın x eksenini time based den kurtarıp, encoder verisine göre hareket ettirmek istiyorum.
yani encoder pulse:0,1,2,3,4,5,6,7 diye x ekseni akarken....
gelen numeric değerler 4,56,4,... y ekseninde dewam edecek.

Translation
The
encoder data in hand, is produced with the numeric value numeric match
the x-axis and time based chart rid of it, I want to act according to
the encoder data.
encoder pulse that: 0,1,2,3,4,5,6,7 he x-axis flows ....
4,56,4 the numeric values, ... y axis will dewam.
You can post in the turkish board for better response

Similar Messages

Multi plot wave form chart

i am acquiring 16 channels simultaniously scan rate of 1000samples/second. using chart with single channel (array of data format) i can see 10 sec duration. with multiplot view of least 4 channel i used waveform property but this will not getting 10 sec duration of x. this is showing just like a graph.
how to show my multiplot at least channel in one chart with continous updation....?
Regards,
Balaji DP

please find an attachment.
chart 1.jpg
i am trying to show the 4 channels of with 1000samples/second. even i am using the chart. i can see only 1 secon of data.
if i try with single channel array of data with out using wave form property with chart i can see 5 minutes of updattion.
how to see multiple plot atleast 4 channel with 5 minutes of duration?
Regards,
Balaji DP
Attachments:
chart1.JPG ‏39 KB
chart2.JPG ‏9 KB

Problem with Wave form chart

Hi
I used ni daq and displayed a live data values on a waveform chat ...and also i am able to save the data as .lvm format .
Now I have to creat two modes to my chart , Live data mode and History mode and show the saved values again on the chart. how to do this ? And also I want to display Auto scale as an icon as shown on the figure . Also I want to change the range of the y -axis by using horizontal pointer slide as shown on the figure.
I attached my code and the front pannel which I have to implement.
Tnx
Attachments:
chart.jpg ‏41 KB
demo.vi ‏87 KB

Hi Cherkose,
for the Autoscale, you can use the property node X Scale>Scale Fit.
When you want to display data from a file, you have to read them first and then make multiplot.
If you want to use different "States" of your programm (either History or Live data) use a state machine or a simple case structure to switch between the states.
regards
Tobias

Wave form chart for different sampling rate

Hi
All,
I have to use different sampling rate to get pressure data. Can I use the waveform chart to monitor the pressure data with time?
If not, what kind of graph should I use?

Different sampling rate than what? A chart or graph can be used. Depends mostly on how you want to update it.

I have generated two square wave forms using NI-9221. These two Square waveforms are suppose to be 90 degrees electrical from one another.

I have two square wave forms from an encoder wheel. I can not seem to generate or calculate the phase of the waveforms. I have tried to extract the data but it is not accurate? I can not use a true false statement with the extracted data either. I have to have the one waveform 90 degrees electrical from the other waveform. Any Suggestions?

Fist thank you both for responding so quickly. I am using a half encoder wheel and the waveforms are certainly show the phases correctly. The operator of this program will not have access to the graph only the data and measurements collected. The reason I am trying to get the phase is because that is going to be a major factor in if the board passes or fails. I extracted the phases from the waveforms but it’s not accurate at all. I think I may try to trigger when to measure the wave and when to stop measuring. Is that Possible?
J. Powell

Trying To Draw The Wav Form of captured audio

hi all , im trying to get into audio proccessing at j2me platform
as a start , i made an application that records audio through the phones microhone and after that drawing the bytearray with its wave form on the canvas.
i used the following capture encoding:
"capture://audio?encoding=pcm&rate=8000&bits=8&channels=1"
the application worked great on the emulators...
after i tried the application on my mobile (motorola E-1000)
i realized that my mobile does not support PCM encoding as for audio capturing the device only supports AMR to capture audio :|
so my question what am i suppose to do to draw the WAveForm of the recorded audio if its stored in bytearray encoded as AMR??
do i need to convert it to wav?
is there any other techinque?
any info will be highly welcome!
thanks in advance.

Did u manage to draw waveform of amr file? I've the same task and i 've the same questions: "do i need to convert it to wav? is there any other techinque?"

Can not see wave form in arrange window logic 9 Please help

I have been using Logic for 3 months now...mostly just importing old wave files from past protools sessions. Everything was working fine until I created a new session to record audio. I record the audio at a nice level...I hit playback...I can hear it fine but I can't see the wave forms. I can see it in the sample editor. I've searched around and found the same problem in the past on some forums......they say to trash preferences... I went to my mac drive...library...preferences and nothing I have no files labeled com.apple.logic.pro now I'm lost....the funny thing is... when I zoom in horizontal ...the wave form shows but it makes the track way too large. Any help would be great. Thanks

In Logic: Preferences/Audio
What is the "Recording Delay" parameter set to?
It should be zero, default is zero. If it's set to a positive or negative Logic will often not show the wavforms. If that's it, it's one of the long standing bugs in Logic.

How can I measure the hertz in a wave form?

How can I measure the hertz in a wave form?

As an example, this is from BBC Technical Requirements for HD material:
3.1.1 Stereo line-up tones
All stereo tracks must use EBU 1KHz tone (left ident). All tones must be sinusoidal, free of distortion and phase coherent between channels.
Digital Audio Reference level is defined as 18dB below the maximum coding value (-18dBFS) as per EBU recommended practice R68.
See also:
http://www.bbc.co.uk/guidelines/dq/pdf/tv/tv_delivery_to_network_programmes_v1.2-2011.pdf
for full document.
And for BBC Radio:
Not every Network requires tone. Check the delivery requirements with the commissioning network or click here.
Reference tone, where used, should be at -18dBFS or PPM 4 on A, B and/or M.
If submitting material with reference tone, tone and programme material must be have been monitored and measured through the same technical chain. The level of the tone must be equivalent to 0dBu and no less than 8dB below peak audio level for the programme material.
THE LEVEL OF TONE MUST HAVE A KNOWN RELATIONSHIP WITH THE LEVEL OF THE PROGRAMME MATERIAL AND THIS MUST BE STATED; for example: “Tone at 8dB below peak programme level”.
As a newcomer to digital sound (my background is camera) I confess to being somewhat confused. We are normally told to record at the highest level possible. So for voice podcasts I tend to record at about -6dB below peak for maximum volume, distributeds on MP3 files.
But I can underatand that televison and radio especially for analogue transmission) may have limited headroom, hence the requirement for -18dB peak = 0dBM.
I remember when we first rented out Digital Betacam cameras, some recordists were recording almost everything OVER -18dBM.
I suspect that until we have an all-digital world, these requiremnents will still be in place.
Many thanks to all. It's a ghreat community!
Brian Rose

Possible to Adjust Selection to Wave Form in EM?

Is there a quick way to adjust the time slection (not clip) to the ends of a wave form? I work with long audio files that contain multiple short bits of audio. I usually end up "saving my selection as" for the individual wave forms to create new smaller files. But even using AutoMark, ai frequently get a bit more silence before or after the audio that I want. It would be helpful if I could drag to select the audio, and automatically have the ends of the highlighted time selection snap to the beginning and end of the audio. It seems like it should be simple, but I couldn't find it in the help function or on a search of the forum.
Can someone point me in the right direction?
Thanks,
Ryan

<If you are talking about Edit View, then the little yellow triangles/handles at the top and bottom of each end of the selection can be dragged, altering the selection accordingly. Zoom in for more accuracy>
Steve,
Thanks for the reply. That's is my current method. But it requires me to manipulate each selection manually. I'm looking for a way to automate that to save time. I do it hundreds of times per project. Mainly I use the auto-mark function combined with the Marker List window. But I also find myself having to select/copy/paste/combine bits of audio to create the 2-5 second blurbs I need, and when that happens it would save time if I could just click a single button and have the little yellow triangles move automatically to the start and end of an audio blob.
Is there a way to do that that you know of? It would seem to me that since several features in AA can automatically detect signal thresholds (i.e. the Auto-Mark feature almost does exactly what I want...it just doesn't actually select the audio), this would be a no-brainer. That's what makes me think I just am not finding something obvious.
Thanks!
Ryan

I am having trouble with the handle bars for music fade in and fade out. It doesn't work. I also cannot see wave forms for music. Cannot select - it is grey. On a deadline and really having problems.

I am trying to finish a video and I want to fade the music in and out. I have read every tutorial I can get and the help info in iMovie. Nothing helsp. I cannot get it to fade by just sliding the handle bars. Other times, the music mutes completely when I try to add a fade. I try to view wave forms for music and it does not allow me to select . it remains grey. I am getting frustrated. I had no problem with 11 version. I now have 10.0.2 version. Can anyone help? my computer is latest Mac Book Pro 2013

This is described in:
http://help.apple.com/imovie/mac/10.0/#mov3b5ded23e
A tip though - if you have a transition at the start or end of a clip it often obscures the fade handle. Trick is to temporarly move the transition (or delete it), move the fade handle then replace the transition.
Geoff.

Control 4 axis by one wave form

Hi
Now I try to control 4 axis stepper motor using one sinusoidai wave form.
At first I could program for one axis attached with this mail.
I try to develop this program for 4 axis, but I am stacking to do.
So would you give me a sugestion how to do.
Please let me know.
Attachments:
stepper drive.jpg ‏66 KB

mikeporter wrote:
I guess I am dense, but CAD files are basically pictures that are very accurate in terms of dimensions. How are they going to control the motion of the effectors, and how is this enum involved?
You know this process would be a lot easier if you just gave us a complete picture of what you are trying to do and the problems you are having. Do you have any code written?
Mike...
finally i have five stepper motors for cartesian robot 5 degrees of freedom x,y,z,Pitch and Yaw. robot will paint several bodies using prependicuar angle of nozzle on object surface with offset 30 cm. the main task of YAW and PITCH is to maitain the prependicular angle.
i have to insert 3D file of object as i have 5 products and select between them using Front panel.
can we use .VI file synchronized with 3D Motion control(X,Y,Z) to control YAW and PITCH?
what's the esaiest method to accomplish my task??
special thanks for your attention.

Can't see wave form after recording...

After I record audio, the wave form (view) goes flat line like I recorded silence. It still plays the audio, but I cant see it to edit it.
How do I see it again?

In all likelihood you have the recording delay setting, set to something other than zero......
no waveform

View audio wave form in A1 and A2 etc in the timeline instead of the Viewer

It's likely this is an amateur question buuut -
Is there anyway to get the audio wave form to show in the Audio layers in the timeline. The only way I've seen to adjust and play with audio is when I double click on one of the tracks and then the audio tab in the viewer will open. I want to be able to see waveform in the timeline and then add or remove markers and adjust from the timeline -
There's got to be some way to adjust audio and play and stop so that you can watch the video and hear audio changes as you tweak it at the same time.

SEQUENCE--> SHOW AUDIO WAVEFORMS

No wave form showing in regions

I recently have the problem that when I record my guitar signal thru my audio interface (tc near or Guitar Rig 3) the wave form of the recording doesn't show in the region.
When I open the sample editor I can see the waveform.
As soon as i change the level of the signal in the sample editor (make it higher OR lower) boom, the wave form shows in the region. Does anybody have a clue?

Thanx for the replay!
to set the recording delay to 0 did the trick, even though I have no idea how it ended up on a value of 677!!
I've set it previously to the proper value which I figured out learning from the fantastic videos by MacProVideo.com.
The proper procedure is shown in video Nr. 18 from "Logic's Latency toolbox".
You can find the particular video also on youtube: http://www.youtube.com/watch?v=gQUngLB5mWg
I can really recommend the Logic series from MacProVideo.com
melodea

Can encode form Premiere directly, but cannot encode in Media Encoder from Premiere Pro

I can encode form Premiere directly, but cannot encode in Media Encoder from Prem.

We need to know a lot more to help you.
Please provide answers to the questions listed here: "FAQ: What information should I provide when asking a question on this forum?"

Wave Form Chart'ın X eksenini encoder verisine bağlamak

Similar Messages

Maybe you are looking for