Wbadmin and the -authsysvol switch

hello everyone
when i run wbadmin with the -authsysvol switch to do a system state restore of a 2008 domain controller once restarted netlogon and sysvol are not shared. dsa.msc wont start and everything is a bit of a mess. if i then go in and change the lastrestoreid
in HKLM\SYSTEM\CurrentControlSet\Control\BackupRestore to another unique string and restart the server sysvol and netlogon are shared again and everything works normally. basically doesnt look like the authsysvol switch is working properly. does
anyone have any ideas whats going on or what ive done wrong?
steps:
start dc in dsrepair mode
restore system state using wbadmin start systemstaterecovery -authsysvol version:"date" -backuptarget:"path"
reboot
point dns to server ip
try and launch dsa/ type domain name\sysvol
get interface not found etc
the keys from this article are in the registry
http://jorgequestforknowledge.wordpress.com/2010/08/12/restoring-the-sysvol-non-authoritatively-when-either-using-ntfrs-or-dfs-r-part-3/
i rename the restoreid to the string in the article reboot and everything is ok
thanks

Hi,
Do you mean that you changed the lastrestoreid in HKLM\SYSTEM\CurrentControlSet\Control\BackupRestore to another unique string, then everything works normally but when the server is rebooted sysvol and netlogon are both unavailable? If so, please refer to the
article below to see if it helps:
The Sysvol and Netlogon Shares Are Missing After You Restore a Domain Controller from Backup
http://support.microsoft.com/kb/316790
Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Similar Messages

IPod nano gen 4 forward button won't work, and the hold switch won't either. I've tried restoring it and it didn't fix the problem. Any suggestions?

The forward button won't work and the hold switch doesn't either. I tried restoring it, but that didn't work.

Restore to factory settings.new iPod if you have not yet already. If still problem time for an appointment at the Genius Bar of an Apple store.

My iPhone 5 quit ringing. I checked settings and the side switch. What now?

My iphone5 quit ringing. I've checked settings and the side switch. What now?

When you go to Settings > Sounds > Ringtones and tap on a ringtone, does it emit a sound then? If so, Go to Settings > Do Not Disturb and make sure it is OFF.
Next steps would be to back up your iPhone, then go to Settings > General > Reset > Reset All Settings.
If the issue continues still, restore the iOS. Last step would be to take it in for service.
Locate a Service location (choose your country in the top right)

My battery died last night and the phone switched itself...

My battery died last night and the phone switched itself off. It has now been charging for 5 hours and still will not switch on. Please help.

Remove and reinsert the battery from the device. Also clean the battery and device connectors with a cloth....then plug the device on the charger.
If that fails then you might have to consider changing the battery.
tanzim
If your query is resolved then please click on “Accept as Solution”
Click on the LIKE on the bottom right if the post deserves credit

My iPhone 4s will not ring and the mute switch is off. Help?

I just got a new 4s for Christmas and the mute switch on the side is off (no orange is showing). I am not hearing any incoming calls, text, voicemail, or email alerts. It will play the ring tone when I select it and will play music. In settings / sounds menu if I have the silent off it does nothing when there is an incoming call or any other alert. If I have the Vibrate switch on in the silent section it will at least vibrate. I am doing some thing stupid? Please help!

Turns out it is hardware issue with the mute switch. It will be replaced but I have to drive 75 miles to the nearest apple store. Or they can ship it to me but put a hold on my credit card of $700.00 until they receive the old phone back.

Cdp neighbour shows the same switch as neighbour and the connected switch

Hi
I have a problem here , cdp neighbor shows the same switch as the neighbor and the real connected switchh . I know it will show only the real connected switch if i shut and no sh . What i just want know is it a symptom for something else
Dist#sh cdp neighbors   Gig 10/10
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
                  D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID        Local Intrfce     Holdtme    Capability Platform Port ID
Sw1
                 Gig 10/10        130              S I   WS-C3560- Gig 0/3
Dist
                 Gig 10/10         156             R S I WS-C6513    Gig 10/10
Thank you

HI,
Did you did shut and no shut in the interface. ?
Is it working fine.?
is it fiber connected cable connected with these devices ?
Regards,
Gurudath K S

When open the article "Inside abandoned airports" on the BBC homepage it initially opens and the immediately switches to an error site. Why?

The current BBC homepage has an article "Inside abandoned airports" which, when I try to open it initially opens and then switches to https://search.yahoo.com/yhs/errorhandler?hspart=gt&hsimp=yhse-gt&q=assets.adobedtm.com%2F5d8d9920c15d663cfa70ef117e3448e4cddcd14f%2Fsat&type=201117. I am currently using Firefox 31.0.
The same article opens without an issue with Internet Explorer 11.0.9600.17239.
It also works with Google Chrome 36.0.1985.143.
What is wrong?

Can you open that article directly?
*http://www.bbc.com/culture/story/20140811-inside-abandoned-airports
You can try these steps in case of issues with web pages:
You can reload web page(s) and bypass the cache to refresh possibly outdated or corrupted files.
*Hold down the Shift key and left-click the Reload button
*Press "Ctrl + F5" or press "Ctrl + Shift + R" (Windows,Linux)
*Press "Command + Shift + R" (Mac)
Clear the cache and remove cookies only from websites that cause problems.
"Clear the Cache":
*Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
"Remove Cookies" from sites causing problems:
*Firefox/Tools > Options > Privacy > "Use custom settings for history" > Cookies: "Show Cookies"
Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem.
*Switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance
*Do NOT click the Reset button on the Safe Mode start window
*https://support.mozilla.org/kb/Safe+Mode
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

My FaceTime constantly fails and the wifi switches to 3G by its self.

It's been happening for awhile now. I can FaceTime from my mac just fine it only happens with my iPhone 4. I'd appreciate some help.

Being the FaceTime only works over wifi i'd suspect your wifi router is the problem
Try updating it's firmware

HT1430 my phone does not ring and the switch is on and speakerphone does not work

CAN ANYONE HELP ME MY RINGTONE ON MY PHONE JUST QUIT WORKING ALONG WITH SPEARKER PHONE AND THE VOLUME SWITCH IT TURNED ON ALONG WITH VOLUME UP.

Try going to settings > sounds and check all of your settings.

Service module placement and the L2 adjacency problem

I'd be very interested to hear others opinions on this. You have a datacenter environment with L2 boundaries at end of row aggregators, then L3 back to the core and edge. You have 6500 service module switches hanging off the core housing ACE and FWSM modules. You want to offer firewalling and load-balancing services to servers around the datacenter.
What is the current best practice ways of resolving the L2 adjacency requirement that the firewalling and load-balancing services impose? L2TPv3? EoMPLS? Any relevant advice, deployment examples, whitepapers etc would be much appreciated!
Thanks for any replies,
George

George
You could i suppose look to use L2TPv3 if your switches support it or EoMPLS but to my mind this is actually using a band aid to fix a problem that shouldn't be there.
We too struggled in our data centres with this setup but remember you only need L2 adjacency if you are running the FWSM in transparent mode or the ACE in bridged mode.
If you are then the cleanest solutions are either
1) redesign core connections to L2
2) deploy 6500 switches in the distribution layer. I say distribution layer because it's not clear from your description what your topology actually is but i'm assuming L2 access to distro and then L3 distro to core and the core switches are the 6500 switches.
Personally i always use the routed L3 approach where possible for fast failover and no STP and in the campus environment it works really well.
However L3 from the access-layer to the distro in the data centre is very limiting and you often come across problems such as the one you are facing.
Now again it does depend on your topology but assuming the issue is your core is L3 connected and you need L2 adjacency with your distro to offer servers i would look to deploy 6500 switches in the distro layer with the service modules in them.
If i have misunderstood please come back with more details.
Jon

Fabric with two Nexus-5548 and a brocade switch does not get fabric updates

We have a fabric containing two Nexus 5548 and a Brocade 5000 switch in interop mode 2. When i make changes to the zoning, the first nexus (the fabric principal) and the brocade switch see the zone changes. The second Nexus switch does not see it. There are no error messages but the change just can't be seen. What can i do to find out, what goes wrong ?

Ouch, deprecated is not the word i wanted to read
We are using 5.1(3)N1(1a) on nexus-rz1-a
and 6.0(2)N1(2) on nexus-rz2-a.
The fabric can be seen :
nexus-rz2-a# show fcs ie vsan 10
IE List for VSAN: 10
IE-WWN                   IE     Mgmt-Id Mgmt-Addr (Switch-name)
10:00:00:05:1e:90:57:27 S(Rem) 0xfffc01 10.88.133.110 (bc-san1)
20:0a:00:2a:6a:72:ba:01 S(Loc) 0xfffc1c 10.88.133.105 (nexus-rz2-a)
20:0a:54:7f:ee:7f:dc:01 S(Adj) 0xfffc0b 10.88.133.100 (nexus-rz1-a)
[Total 3 IEs in Fabric]
nexus-rz1-a# show fcs ie vsan 10
IE List for VSAN: 10
IE-WWN                   IE     Mgmt-Id Mgmt-Addr (Switch-name)
10:00:00:05:1e:90:57:27 S(Adj) 0xfffc01 10.88.133.110 (bc-san1)
20:0a:00:2a:6a:72:ba:01 S(Adj) 0xfffc1c 10.88.133.105 (nexus-rz2-a)
20:0a:54:7f:ee:7f:dc:01 S(Loc) 0xfffc0b 10.88.133.100 (nexus-rz1-a)
[Total 3 IEs in Fabric]
I try to distribute the zoneset this way:
zoneset distribute vsan 10
Zoneset distribution initiated. check zone status
nexus-rz1-a# show zone status
VSAN: 10 default-zone: deny distribute: full Interop: 2
    mode: basic merge-control: allow
    session: none
    hard-zoning: enabled broadcast: disabled
Default zone:
    qos: none broadcast: disabled ronly: unsupported
Full Zoning Database :
    DB size: 6291 bytes
    Zonesets:1 Zones:62 Aliases: 44
Active Zoning Database :
    DB size: 10243 bytes
    Name: FABRIC1 Zonesets:1 Zones:60
Status: Zoneset distribution completed at 08:06:00 UTC Dec 3 2013
nexus-rz2-a# show zone status
VSAN: 1 default-zone: deny distribute: active only Interop: default
    mode: basic merge-control: allow
    session: none
    hard-zoning: enabled broadcast: disabled
Default zone:
    qos: none broadcast: disabled ronly: unsupported
Full Zoning Database :
    DB size: 4 bytes
    Zonesets:0 Zones:0 Aliases: 0
Active Zoning Database :
    Database Not Available
Status:
VSAN: 10 default-zone: deny distribute: full Interop: 2
    mode: basic merge-control: allow
    session: none
    hard-zoning: enabled broadcast: disabled
Default zone:
    qos: none broadcast: disabled ronly: unsupported
Full Zoning Database :
    DB size: 6291 bytes
    Zonesets:1 Zones:62 Aliases: 44
Active Zoning Database :
    DB size: 10243 bytes
    Name: FABRIC1 Zonesets:1 Zones:60
Status: Activation completed at 13:03:42 UTC Dec 2 2013

Trouble with the Hold Switch

I was using the Hold switch without a problem since I got my mini last June. Just recently the Hold switch starting acting up. First it was staying engaged after I switched it off - I know this because I can connect it to my computer and when it is recognized and lights up, I can see the locked icon. After I disconnect it from the computer the screen is blank and doesn't respond - can't reset it either. After an hour or so though it finally seems to become unstuck and I find it turned on by itself.
Now the latest "mind of it's own" thing is that while I'm playing songs, the locked icon will come on intermittenly. I've looked for articles and questions but don't see this problem. Any suggestions?

For a couple of weeks I worked around this by turning
off the hold switch about an hour before I wanted to
use it, and it would turn on.
I had to charge it this weekend, and since, I can't
get it out of the hold mode. Again I can tell it's
locked because when I connect it to the computer (and
the hold switch is off, I can see the locked icon.
Any body else experience this kind of hold switch
problem??
I am having a problem with my ipod 4th gen. It will not get out of hold. The closed lock stays in the upper bar of the iPod.
I toggle and toggle - to no avail. Help. I do not want to buy another. I got it 12/2004.

Can I use DHCP snooping and IOS DHCP server on the same switch stack

Hello,
I am shortly going to be deploying a Cisco CallManager solution for a customer whose network comprises stacks of Catalyst 3850 switches.
There is no separate core/server farm switch so the CallManager servers, voice gateways and IP phones will all plug into the same stack and be in the same VLAN (not my choice!).
For security we want to enable DHCP snooping and were planning on using the IOS DHCP server on the Catalyst switch stack.
Will this work? - when I enable DHCP snooping in networks with separate access layer switches I set the uplinks to the core as trusted links.
I am not sure whether DHCP snooping will work in this case. Do I need to set the VLAN interface on the switch as trusted, is this even possible?
Unfortunately I do not have access to a layer 3 switch to test this at the moment.
Thanks

Nope. That's the issue.
They'll sync on a third device acting as a hotspot, but the device sending a signal is not "on" the network it creates so the airport is all by itself on that network. At least that is what it looks like to me. Anyone have another take on it? Seems pretty silly that an iPad can put out a wifi signal, an Airport Express can receive a wifi signal, and yet there is no simple way to get them to communicate under this particular condition.

HT3053 I have a 13inch MacBook Pro and when I switch it on the apple logo appears then a slot and the circular symbol which is turning and then before opening the home screen it switches off again. Is there a sequence that I can use to force it to load.

I have got a 13 inch MacBook Pro and it got stuck in a loop so I switched it off by holding the power button down and now when I switch it on the apple logo appears then I get a blank slot at the bottom of the screen then the circle appears and rotates and then it switches off again, I have tried starting it again with the system disc that came with it when it was new but it makes no difference. Is there a sequence that I can use to force it to start.

Sorry. We can't help you. It's no longer an iPhone. Apple won't touch it.
Take it to whoever replaced the screen and see if they can help you.
iPhones are not user servicable and Apple does not sell iPhone parts at all. I'd be surprised if you were actually able to back it up at this point. It sounds like it's completely borked.

I have an iphone 4 for verizon and i am going to switch phones and get a droid motorolla 4g phone and the droid doesnt have a sim card. does my iphone 4 have a sim card that i can put in the droid? can i buy sim cards separately online for the droid?

i have an iphone 4 for verizon and i am going to switch phones and get a droid motorolla 4g phone and the droid doesnt have a sim card. does my iphone 4 have a sim card that i can put in the droid? can i buy sim cards separately online for the droid?

Brandon2184 wrote:
The iPhone 4 uses a "Nano SIM"
The CDMA iPhone 4 does not use a SIM at all. There is no SIM slot. It is a pure CDMA phone.

Wbadmin and the -authsysvol switch

Similar Messages

Maybe you are looking for