WCCP Redirection on a GRE Tunnel

For some of our smaller branch offices we run GRE tunnels through a secured IPSec VPN connection over the Internet. Will WCCP redirect work if configured on the GRE Tunnel interface?

Hi,
Yes, it will work.
Regards,
Erik
Sent from Cisco Technical Support iPad App

Similar Messages

Redirection on GRE tunnels

I have implemented WCCP redirect on a serial interface I have. I also have a GRE tunnel interface sourced from that same serial interface.I would like to know the IOS order of operation for that GRE tunnel interface in regards to redirection. Do I have to specifically configure the "ip wccp redirect" command on the tunnel interafce or the command on the underlying serial interface would suffice?

Hello Shiravani,
You need to configure the "ip wccp redirect " on the GRE tunnel interface itself and not the serial interface ( if you want to redirect traffic coming out from the GRE tunnel ).
The IOS order does not really apply on this case,the GRE tunnel is just like any other interface.( GRE/ipsec packets are handled by physical (WAN) interface.)
I also suggest to do a lab if any doubts or further questions before you making the changes.
Hope this helps!
Felix

WSA & CAT6500 WCCP GRE Tunnel

Hello everyone
First time writing in the support community. So exiting!!!!
I am trying to have a transparent WSA (7.5) with a CAT6509 SXF7 WCCP. between them there is a Firewall/router. so I built the WCCP with GRE/L3.
so far so good. WCCP GRE tunnel is there.
However cannot surf the internet.
After much troubleshooting (wireshark mainly) I believe I know where the problem is.
Client want to surf the Internet (http)
Client sends a SYN request to the IP of the website (after resolving DNS)
CAT6500 tunnels the request with GRE to WSA
WSA receives request and sends to SYN packet to the webpage.
Webpage sends a SYN ACK to WSA (no spoofing)
PROBLEM: WSA then sends the SYN ACK without GRE to client with in turn does not go through the FW
Client does not receive SYN ACK, sends another SYN and then another until he gives up.
Question: How can I force the WSA to return traffic through the GRE tunnel.
I already chose return method as "alloow GRE only" under WCCPv2 Service
So look forward to receive some help

Hi,
Yes, it will work.
Regards,
Erik
Sent from Cisco Technical Support iPad App

WCCP v2 - "ip wccp redirect out" command

I'd like to validate the following:
1.- I have this equipment:
Cisco IOS Software, C3560 Software (C3560-IPSERVICESK9-M), Version 12.2(53)SE, RELEASE SOFTWARE (fc2)
* Packet redirection on an outbound interface that is configured by using the ip wccp redirect out interface configuration command. This command is not supported.
I'd like to know if there's a version that support the command.
1.- If there's no version that supports the command in the equipment. Then, which is the "smallest" switch model that can support the command.
Thanks a lot for your support.

Ali,
The issue is that not all of your traffic is being redirected in hardware. When you configure outbound interception on the 6500/Sup720, the first packet for every flow is punted to the MSFC and switched in software. Subsequent packets for that flow are redirected in hardware using NetFlow forwarding. So the impact on your MSFC CPU utilization is tied to the number of connections per second (cps) being redirected, as well as some overhead for managing the NetFlow forwarding table.
In addition, the command 'ip wccp redirect exclude in' is not completely understood by the 6500 hardware. So again, the first packet for every flow entering the interface with this configured must be punted to the MSFC and switched in software.
And finally, the use of mask assignment (as opposed to hash assignment) is needed to ensure that all interception is handled in hardware).
Taking these three points together, the following configuration is required if you want WCCP interception to be handled completely in hardware on the 6500/Sup720:
- GRE or L2 forwarding
- Mask assignment
- Inbound redirection
- No 'ip wccp redirect exclude in'
This will require you to reverse the logic of how your service groups are applied:
- 'ip wccp web-cache redirect in' on client-facing interfaces
- 'ip wccp 95 redirect in' on internet-facing interfaces
If you have any questions, please let us know.
Zach

Windows Replication RPC Problems with IPSec GRE Tunnel

We have been having significant issue in troubleshooting random RPC errors with our directory controllers (MS AD 2008R2) and our distributed file shares. Both services will randomly stop working, throwing RPC errors as the resulting cause. We have been all over both Cisco and Microsoft forums in trying to troubleshoot this problem. I'm trying to the Cisco forums first to see if anyone has any network layer thoughts as to best practices or ways to configure the tunnel.
Our network is simple: two small branch offices connected to each other with two Cisco 2901 ISRs. An IPSec GRE tunnel exists between both offices. Interoffice bandwidth is approximately 10mbps. Pings between offices work, remote desktop works most of the time, file transfers work, and DNS lookups work across both locations. We really don't have a complicated environment, I'd think it wouldn't be too hard to set up. But this just seems to be escaping me. I can't think of anything at the network layer that would be causing problems but I was curious whether anyone else out there with knowledge of small office VPNs might be able to render some thoughts on the matter.
Please let me know if there is anything further people need to see. My next step is MS forums but I wanted to eliminate layer 3 first.
Tunnel Config:
crypto map outside_crypto 10 ipsec-isakmp
set peer x.x.x.x
set transform-set ESP-AES-SHA
match address 102
crypto ipsec df-bit clear
interface Tunnel0
bandwidth 10240
ip address x.x.x.x x.x.x.x
no ip redirects
ip mtu 1420
ip virtual-reassembly in
zone-member security in-zone
ip tcp adjust-mss 1375
tunnel source GigabitEthernet0/0
tunnel destination x.x.x.x
crypto ipsec df-bit clear
end

Hi,
Based on the third-party article below, you can setup VPN connection between Windows VPN client and Cisco firewall:
Step By Step Guide To Setup Windows 7/Vista VPN Client to Remote Access Cisco ASA5500 Firewall
What is the Windows server 2008 R2 for, a RADIUS server? If yes, maybe the links below would be helpful to you:
RADIUS: Configuring Client VPN with Windows 2008 Network Policy Server (NPS) RADIUS Authentication
Configuring RADIUS Server on Windows 2008 R2 for Cisco Device Logins
RADIUS authentication for Cisco switches using w2k8R2 NPS
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.
Best regards,
Susie

GRE tunnel could not be used by the hosts connected to the router

Hi,
I am using cisco ASR1013 (RP2) and a Mikrotik Router for setting up a GRE tunnel for LAN to LAN routing over a broadband link. The tunnel works fine (able to ping tunnel end points and also all the connected interfaces on both the Mikrotik and Cisco ASR) but the hosts that are connected directly to the Cisco router interface over a layer 2 cisco switch are unable to connect (ping) the hosts or connected interfaces on the mikrotik side. I am sure its not a mikrotik issue as i dont see any traffic coming through the tunnel using the mikrotik torch utility. There are no ACL's or firewall rules on any of the devices......
Source and destination of the tunnel are public IP's and are pingable via internet (The tunnel is connected and endpoints are pingable)
Mikrotik connected interface IP = 192.168.253.1/24
Mikrotik tunnel end point IP = 192.168.254.1/30
Cisco tunnel end point IP = 192.168.254.2/30
Connected cisco subnet to reach Mikrotik = M.N.O.32/28
Cisco interface IP for LAN = M.N.O.33
Test host IP on the LAN subnet = M.N.O.34
The below is my Cisco config
ASR-1#sh run int tun 1
Building configuration...
Current configuration : 144 bytes
interface Tunnel1
ip address 192.168.254.2 255.255.255.252
ip mtu 1400
tunnel source A.B.C.D
tunnel destination W.X.Y.Z
end
ASR-1#sh run int g0/1/7
Building configuration...
Current configuration : 280 bytes
interface GigabitEthernet0/1/7
description LAN
ip address M.N.O.33 255.255.255.240
ip verify unicast source reachable-via rx
no negotiation auto
cdp enable
end
ASR-1#sh ip ro 192.168.253.1
Routing entry for 192.168.253.0/24
Known via "static", distance 1, metric 0 (connected)
Routing Descriptor Blocks:
* directly connected, via Tunnel1
Route metric is 0, traffic share count is 1
ASR-1#ping 192.168.253.1 so M.N.O.33
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.253.1, timeout is 2 seconds:
Packet sent with a source address of M.N.O.33
Success rate is 100 percent (5/5), round-trip min/avg/max = 5/5/6 ms
ASR-1#pi M.N.O.34
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to M.N.O.34, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
If i try to ping 192.168.253.1 (network connected to Mikrotik) from the host M.N.O.34 (the gateway of this host is M.N.O.33 - Int g0/1/7 of the Cisco ASR), i cannot reach detination - request timed out.... Below are the results of trace and ping from the host connected to ASR G1/0/7
PING TO THE GATEWAY *********
[root@localhost ~]# ping M.N.O.33
PING M.N.O.33 (M.N.O.33) 56(84) bytes of data.
64 bytes from M.N.O.33: icmp_seq=1 ttl=255 time=0.161 ms
64 bytes from M.N.O.33: icmp_seq=2 ttl=255 time=0.143 ms
^C
--- M.N.O.33 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1357ms
rtt min/avg/max/mdev = 0.143/0.152/0.161/0.009 ms
PING TO THE TUNNEL END POINT IN CISCO ASR
[root@localhost ~]# ping 192.168.254.2
PING 192.168.254.2 (192.168.254.2) 56(84) bytes of data.
64 bytes from 192.168.254.2: icmp_seq=1 ttl=255 time=0.141 ms
64 bytes from 192.168.254.2: icmp_seq=2 ttl=255 time=0.141 ms
^C
--- 192.168.254.2 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1739ms
rtt min/avg/max/mdev = 0.141/0.141/0.141/0.000 ms
PING TO THE TUNNEL ENDPOINT IN MIKROTIK
[root@localhost ~]# ping 192.168.254.1
PING 192.168.254.1 (192.168.254.1) 56(84) bytes of data.
^C
--- 192.168.254.1 ping statistics ---
11 packets transmitted, 0 received, 100% packet loss, time 10413ms
PING TO THE CONNECTED INTERFACE ON MIKROTIK
[root@localhost ~]# ping 192.168.253.1
PING 192.168.253.1 (192.168.253.1) 56(84) bytes of data.
^C
--- 192.168.253.1 ping statistics ---
4 packets transmitted, 0 received, 100% packet loss, time 3641ms
TRACE TO THE CONNECTED INTERFACE ON MIKROTIK
[root@localhost ~]# traceroute 192.168.253.1
traceroute to 192.168.253.1 (192.168.253.1), 30 hops max, 60 byte packets
1 M.N.O.33 (M.N.O.33) 0.180 ms 0.156 ms 0.145 ms
2 * * *
3 * * *
4 * * *
5 * * *
Please help

Hi,
Sorry for the delayed response ....Both ends static routes are added for the connected test interfaces.....
Regards,
Mahesh

IP routing utilizing Verizon private network (GRE tunnel) with remote cellular gateways

Okay, I give up, and think I have done my due diligence (I have been engrossed and fascinated spending many more hours than allotted to try and learn some of the finer details). Time for some advice. My usual trade is controls engineering which generally require only basic knowledge of networking principals. However I recently took a job to integrate 100 or so lift stations scattered around a county into a central SCADA system. I decided to use cellular technology to connect these remote sites back to the main SCADA system. Well the infrastructure is now in and it’s time to get these things talking. Basic topology description is as follows: Each remote site has an Airlink LS300 gateway. Attached to the gateway via Ethernet is a system controller that I will be polling via Modbus TCP from the main SCADA system. The Airlinks are provisioned by Verizon utilizing a private network with static IP's. This private networks address is 192.168.1.0/24. Back at the central office the SCADA computer is sitting behind a Cisco 2911. The LAN address of the central office is 192.168.11.0/24. The 2911 is utilizing GRE tunnels that terminate with Verizon. The original turn up was done with another contractor that did a basic config of the router which you will find below. As it stands now I am pretty confident the tunnels are up and working (if I change a local computers subnet to 255.255.0.0 I can surprisingly reach the airlinks in the field), but this is obviously not the right way to solve the problem, not to mention I was unable to successfully poll the end devices on the other side of the Airlinks. I think I understand just about every part of the config below and think it is just missing a few items to be complete. I would greatly appreciate anyone’s help in getting this set up correctly. I also have a few questions about the set up that still don’t make sense to me, you will find them below the config. Thanks in advance.
no aaa new-model
ip cef
ip dhcp excluded-address 10.10.10.1
ip dhcp pool ccp-pool
import all
network 10.10.10.0 255.255.255.248
default-router 10.10.10.1
lease 0 2
ip domain name yourdomain.com
no ipv6 cef
multilink bundle-name authenticated
username cisco privilege 15 one-time secret
redundancy
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key AbCdEf01294 address 99.101.15.99
crypto isakmp key AbCdEf01294 address 99.100.14.88
crypto ipsec transform-set VZW_TSET esp-3des esp-md5-hmac
mode transport
crypto map VZW_VPNTUNNEL 1 ipsec-isakmp
description Verizon Wireless Tunnel
set peer 99.101.15.99
set peer 99.100.14.88
set transform-set VZW_TSET
match address VZW_VPN
interface Tunnel1
description GRE Tunnel to Verizon Wireless
ip address 172.16.200.2 255.255.255.252
tunnel source 22.20.19.18
tunnel destination 99.101.15.99
interface Tunnel2
description GRE Tunnel 2 to Verizon Wireless
ip address 172.16.200.6 255.255.255.252
tunnel source 22.20.19.18
tunnel destination 99.100.14.88
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address 10.10.10.1 255.255.255.248
shutdown
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 192.168.11.1 255.255.255.0
duplex auto
speed auto
interface GigabitEthernet0/2
ip address 22.20.19.18 255.255.255.0
duplex full
speed 100
crypto map VZW_VPNTUNNEL
router bgp 65505
bgp log-neighbor-changes
network 0.0.0.0
network 192.168.11.0
neighbor 172.16.200.1 remote-as 6167
neighbor 172.16.200.5 remote-as 6167
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip route 0.0.0.0 0.0.0.0 22.20.19.19
ip access-list extended VZW_VPN
permit gre host 99.101.15.99 host 22.20.19.18
permit icmp host 99.101.15.99 host 22.20.19.18
permit esp host 99.101.15.99 host 22.20.19.18
permit udp host 99.101.15.99 host 22.20.19.18 eq isakmp
permit gre host 22.20.19.18 host 99.101.15.99
permit gre host 22.20.19.18 host 99.100.14.88
access-list 23 permit 10.10.10.0 0.0.0.7
control-plane
end
So after spending countless hours analyzing every portion of this, I think that adding one line to this will get it going (or at least closer).
ip route 192.168.1.0 255.255.0.0 22.20.19.19
That should allow my internal LAN to reach the Airlink gateways on the other side of the tunnel (I think)
Now for a couple of questions for those that are still actually hanging around.
#1 what is the purpose of the Ethernet address assigned to each tunnel? I only see them being used in the BGP section where they are receiving routing tables from the Verizon side (is that correct?). Why wouldn't or couldn't you just use the physical Ethernet address interface in its place (in the BGP section)?
#2 is the config above correct in pointing the default route to the physical Ethernet address? Does that force the packets into the tunnel, or shouldn’t you be pointing it towards the tunnel IP's (172.16.200.2)? If the config above is correct then I should not need to add the route I described above as if I ping out to 192.168.1.X that should catch it and force it into the tunnel where Verizon would pick it up and know how to get it to its destination??
#3 Will I need to add another permit to the VZW_VPN for TCP as in the end I need to be able to poll via Modbus which uses port 502 TCP. Or is TCP implicit in some way with the GRE permit?
I actually have alot more questions, but I will keep reading for now.
I really appreciate the time you all took to trudge through this. Also please feel free to point anything else out that I may have missed or that can be improved. Have a great day!

This post is a duplicate of this thread
https://supportforums.cisco.com/discussion/12275476/proper-routing-lan-through-verizon-private-network-gre-airlink-gateways
which has a response. I suggest that all discussion of this question be done through the other thread.
HTH
Rick

When do i have to use a gre over ipsec tunnel? i have heard that when i m using a routing protocol and vpn site to site i need a gre tunnel

i have configured a network with ospf and a vpn site to site without gre tunnel and it works very well. I want to know, when do i have to use gre tunnel over ipsec

Jose,
It sounds like you currently have an IPsec Virtual Tunnel Interface (VTI) configured. By this, I mean that you have a Tunnel interface running in "tunnel mode ipsec ipv4" rather than having a crypto map applied to a physical interface. In the days before VTIs, it was necessary to configure GRE over IPsec in order to pass certain types of traffic across an encrypted channel. When using pure IPsec with crypto maps, you cannot pass multicast traffic without implementing GRE over IPsec. Today, IPsec VTIs and GRE over IPsec accomplish what is effectively the same thing with a few exceptions. For example, by using GRE over IPsec, you can configure multiple tunnels between two peers by means of tunnels keys, pass many more types of traffic rather than IP unicast and multicast (such as NHRP as utilized by DMVPN), and you can also configure multipoint GRE tunnels whereas VTIs are point to point.
Here's a document which discusses VTIs in more depth: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_vpnips/configuration/xe-3s/sec-sec-for-vpns-w-ipsec-xe-3s-book/sec-ipsec-virt-tunnl.html#GUID-A568DA9D-56CF-47C4-A866-B605804179E1
HTH,
Frank

GRE Tunnel and static PAT

Hi to all,
I would like to know if it is possible to create a static Port Address Translation (PAT) that would translate a routable IP address to a private address where a GRE tunnel would end.
In other words, I am trying to see if we can use a static PAT for a GRE tunnel like the one that we can used to reach a HTTP server using a private IP address via static PAT to a routable IP address.
Just trying to see if it is possible to initiate a GRE tunnel from 192.168.1.1 (R1) and used 1.1.1.1 (R2), IP address reachable via internet, as destination address, in the case where we would do a PAT translation on R2 in order to actually terminate the tunnel on R3 router. The static PAT on R2 would translate 1.1.1.1 to 172.16.1.2.
I am basically looking for an equivalent to the following static PAT but for GRE tunnel
          ip nat inside source static tcp 10.10.10.5 80 192.168.2.1 80
Thanks for your help
Stephane

Hello Stephane,
GRE is neither TCP nor UDP, GRE has its own protocol number 47. You can allow the traffic by either by calling GRE instead of TCP or UDP or by just putting a normal IP static NAT entry.
Extended IP access list GRE
    10 permit tcp any any eq 47 log <--- No Hits
    15 permit tcp any any log          <--- No Hits
    20 permit udp any any eq 47 log <--- No Hits
    25 permit udp any any log          <--- No Hits
    30 permit gre any any log (20 matches)
    40 permit ip any any (43 matches)
*Mar 1 00:27:48.435: IP: tableid=0, s=10.10.10.2 (local), d=10.10.10.1 (Tunnel1), routed via FIB
*Mar 1 00:27:48.435: IP: s=10.10.10.2 (local), d=10.10.10.1 (Tunnel1), len 100, sending
*Mar 1 00:27:48.435:     ICMP type=0, code=0
*Mar 1 00:27:48.435: IP: s=192.168.9.5 (Tunnel1), d=192.168.8.2 (FastEthernet0/0), len 124, sending, proto=47
I hope it helps great for you. Please rate if you fell this is helpfull.
Thanks,
Kasi

GRE Tunnel/NAT with multiple subnets and interfaces

So, I am not sure if we are trying to accomplish too many things at once and what we are attempting to do is not possible or if we are missing something in our configurations...
Here is the situation...
We are migrating some equipment between datacenters. The equipment only a has a /27 worth of IP space assigned to it so we cannot simply "move" the IP space to the new datacenter. Further because we have several VPNs terminated in the old IP space that originate from devices we do not directly control and are essential in continuing to provide service, it was/is difficult to magically update some DNS entries and change IP addresses overnight. The last twist in this puzzle is that at the new datacenter, we will deploying some new equipment that will be in a separate subnet (with a separate Windows AD structure) but sharing the new public IP space we have in the new datacenter.
We thought using a GRE tunnel, some trunks, and a bunch of NATs would make the whole process easy and we tested ti in a lab and everything SEEMED to work. However, when we performed the move we ran into an odd issue that we were unable to figure out and had to go back to a failsafe configuration that has the essentials up and running, but the environment is not running in an ideal way for us to gradually transition as we would like.
Essentially what we had/have and how it was configured is as follows:
Site A
Edge Router - x.x.x.x /24 BGP announcement
x.x.x.y/27 that is within the /24 that we need at site b
GRE tunnel configuration
interface tunnel0
ip address 10.x.x.1 255.255.255.252
tunnel source <router edge IP>
tunnel destination <site b router edge ip>
keepalive 10 3
static route for site a public ip to bring it to site b via GRE tunnel
ip route x.x.x.y 255.255.255.224 10.x.x.2
Site B
Edge Router - y.y.y.y /24 BGP announcement
Similar GRE tunnel configuration (tunnel comes out and works so don't think issue is here)
2 Vlans (1 for site a ip space, 1 for site b ip space)
int vlan 50
ip address x.x.x.1 /27
int vlan 51
ip address y.y.y.129 /25
Trunk port for the VLANs going down to an ASA
int g1/1
swi mode trunk
swi trunk native vlan 51
swi tru all vlan 50,51
swi tru en dot1q
Then on the ASA, I have 2 physical interfaces for 4 logical interfaces (outside, outsideold, inside, insideold)
int e0/0
nameif outside
sec 0
ip address y.y.y.130 /25
int e0/0.50
nameif outsideold
sec 0
ip address x.x.x.2 /27
vlan 51
int e0/1
nameif inside
sec 100
ip address 192.168.y.1 /24
int e0/1.60
nameif insideold
sec 100
ip address 192.168.x.1 /24
vlan 60
A static route using the new ip space on the native outside interface...
route 0 0 y.y.y.129
And then I have some nat rules which is where I think things go a little haywire...
object network obj-y.y.y.0-24
subnet y.y.y.0 255.255.255.0
nat (inside,outside) dynamic interface
object network obj-x.x.x.0-24
subnet x.x.x.0 255.255.255.0
nat (insideold,outside) dynamic interface
object network obj-y.y.y.135-160
range y.y.y.135 y.y.y.160
object network obj-192.168.y.135-160
range 192.168.y.135 192.168.y.160
nat (inside,outside) static obj-y.y.y.135-160
object network obj-x.x.x.10-20
range x.x.x.10 x.x.x.20
object network obj-192.168.x.10-20
range 192.168.x.10 192.168.x.20
nat (insideold,outsideold) static obj-x.x.x.10-20
From some debugging and looking at packet-tracer, I found out I left out the below which was needed to properly nat traffic as it leaves the outside interface (when the default sends the traffic)
object network obj-192.168.x.10-20-2
range 192.168.x.10 192.168.x.20
nat (insideold,outside) static obj-x.x.x.10-20
There are / were a bunch of other nat exemptions for the VPNs and specific external routes to ensure all vpn traffic exited the "outsideold" interface which is where all the existing tunnels were terminated.
Everything appeared to be working great as all the VPN tunnels came up perfectly as expected and traffic appeared to be flowing, except for some of the most important traffic. The following was what was observed:
1. Any traffic using the dynamic NAT (ie...a machine with IP x.x.x.200 or y.y.y.20) would connect to the internet perfectly and work fine using the "new interface ip".
2. Any traffic in the "new range" using a one to one nat worked perfectly (ie y.y.y.140). Internet would work etc and nat translation would properly occur and everything could connect fine as expected.
3. ICMP packets to "old ip range" flowed perfectly fine to one to one nat IP (ie I could ping x.x.x.20 from outside) and likelise I could ping anywhere on the internet from a machine with a static natted ip.
4. Heres the butt...no traffic other than ICMP would reach these machines with static ips. Same range, same subnet as ones using the dynamic port translation that worked perfectly. Do not understand why this was / is the case and this is what I am seeking a solution to. I have attempted the following troubleshooting steps without success:
A. Confirmed MTU size was not an issue with the GRE tunnel. 2 methods, one plugging to edge router and using the "outsideold" ip space works perfectly and 2 if I assign outsideold ip space to "outside" interface, everything nats fine.
B. Ran packet-tracer, all results show "allow" as if I should be seeing the packets.
C. Confirmed local windows machine firewall was off and not blocking anything.
D. Reviewed logs and observed SYN timeouts and TCP teardowns as if the firewall is not getting a response and this is where I am stumped. There is no path around the firewall so asymmetric routing should not be an issue and if that was the problem it should not work when the "outsideold" ip space is assigned and natted from the "outside" interface, but it does. Packet-tracer shows proper nat translations occurring and there is definitely proper routing along the path for stuff to return to the network or ICMP would not work (IE I can ping www.google.com but not open the web page).
So what simple piece of the nat configuration am I overlooking because I cannot possible wrap my head around it being anything else.
Any suggestions / lessons would be greatly appreciated.

is this still a problem?

Does introducing WCCP redirect for WAAS disrupt Netflow information?

Before installing WAAS and WCCP redirect on some 6500 interfaces in our data center, those interfaces showed Netflow flows for users at a remote location accessing servers at our data center. Now with WCCP redirecting that traffic to the WAEs, I notice the only netflow flows for that remote location are UDP flows and some ICMP stuff.
Is this an unintended consequence of installing WAAS - that netflow statistics are going to be skewed by not showing flows that are now accelerated?

I believe your problem may be due to the fact that you are redirecting http
based traffic per the ACL configuration. The sup720 uses wccp v2 as a default
version,however, the Sup720 does NOT support the hardware-based redirection for the TCP port 80 when we enable wccpv2.
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/122sx/swcg/wccp.
htm#wp1017009
Support for Non-HTTP Services:
WCCPv2 allows redirection of traffic other than HTTP (TCP port 80 traffic), including a variety of UDP and TCP traffic. WCCPv1 supported the redirection of HTTP (TCP port 80)traffic only. WCCPv2 supports the redirection of packets intended for other ports, including those used for proxy-web cache handling, File Transfer Protocol (FTP) caching, FTP proxy handling, web caching for ports other than 80, and real audio, video, and telephony applications.

Ip route command in GRE tunnel

Hi Everyone,
I have setup GRE Lab between Routers R1 and R3.
R1 is connected to R2 using OSPF and R2 is connected to R3 using OSPF.
I config GRE tunnel interface on R1 and R3.
R1 has internal subnet say 100.x.x.x.x to share with R3.
R3 has internal Lan subnet say 101.x.x.x.x to share with R1.
Interesting traffic to pass through GRE tunnel is subnets 100.x.x.x. and 101.x.x.x.x.
R1 tunnel config
R1# sh run int tunnel 0
Building configuration...
Current configuration : 168 bytes
interface Tunnel0
ip address 13.13.13.1 255.255.255.0
keepalive 3
cdp enable
tunnel source Loopback0
tunnel destination 20.0.0.1
tunnel path-mtu-discovery
R3 Tunnel config
R3#sh run int tunnel 0
Building configuration...
Current configuration : 158 bytes
interface Tunnel0
ip address 13.13.13.3 255.255.255.0
keepalive 3 1
tunnel source Loopback0
tunnel destination 10.0.0.1
tunnel path-mtu-discovery
So my question is instead of using Routing protocols to advertise the Lan subnets from R1 and R3 can i use static routes?
for example
If i can use static routes say on R1
ip route 101.101.101.101 255.255.255 ?
what should be next hop IP here ?
tunnel interface of R3 Router or physical interface of R3 that connects to R2?
Then same way i can use static routes on R3 right ?
Thanks
Mahesh

Hello Mahesh,
You can use IP address as long as Tunnel IP addresses on both sides are in the same subnet. So in your case you can use
ip route 101.101.101.101 255.255.255 13.13.13.3
Or you can use the tunnel interface
ip route 101.101.101.101 255.255.255 Tunnel0
Although I have seen issues in some cases when the interface name is used instead of tunnel IP.
Please rate this post if helpful.
THanks
Shaml

Apply WCCP redirect to logical or physical interface?

If there is a logical subinterface configured under its physical interface (for example serial0/0/0.100 for routing), I should apply WCCP redirect (ip wccp 62 redirect in) to the logical interface, not the physical interface. Is that correct?
Thanks

Yes. You apply WCCP redirect to subinterface if you are using sub interfaces.
Regards.
PS: Please mark this Answered, if it answers your question.

Best way to pass IPv4 and IPv6 traffic over a GRE Tunnel

Hello,
We have two 3825 routers with Advanced Enterprise IOS 12.4.9(T). Each of them serves many IPv4 (private and public) and IPv6 networks on their respective site.
We have created a wireless link between the two, using 4 wireless devices, with IP Addresses 10.10.2.2, 3, 4, 5 respectively (1 and 6 are the two end Ethernet interfaces on the routers).
Then we created a GRE tunnel over this link using addresses 172.16.1.1 and 2 (for the two ends) to route traffic over this link.
Now we want to route IPv6 traffic over the same link. However, we found that simply routing the IPv6 traffic over the above GRE / IP tunnel did not work.
Questions:
Is there a way we can use the same (GRE / IP) tunnel to transport both IPv4 and IPv6 traffic?
If not, can we setup two GRE tunnels over the same wireless link, that is, one GRE / IP for IPv4 traffic and a second one GRE / IPv6 for IPv6 traffic?
In brief, what is the suggested way to transport IPv4 and IPv6 traffic over the aforementioned (wireless) link?
I have read http://www.cisco.com/c/en/us/td/docs/ios/12_4/interface/configuration/guide/inb_tun.html#wp1061361 and other Internet material, however I am still confused.
Please help.
Thanks in advance,
Nick

We have set up two tunnels over the same link, one GRE / IP for the IPv4 traffic and one IPv6 / IP ("manual") for the IPv6 traffic. This setup seems to be working OK.
If there are other suggestions, please advise.
Thanks,
Nick

Problem with a simple GRE tunnel

Hello everyone:
I have a problem with a simple GRE tunnel, and can not make it work, the problem lies in the instruction "tunnel source loopback-0" if I use this command does not work, now if I use "tunnel source <ip wan >" if it works, someone can tell me why?
Thanks for your help
Router 1: 2811
version 12.4
no service password-encryption
hostname cisco2811
no aaa new-model
ip cef
interface Loopback0
ip address 2.2.2.2 255.255.255.255
interface Tunnel0
ip address 10.10.1.1 255.255.255.0
tunnel source Loopback0
tunnel destination 217.127.XXX.188
interface Tunnel1
ip address 10.10.2.1 255.255.255.0
tunnel source Loopback0
tunnel destination 80.32.XXX.125
interface FastEthernet0/0
description LOCAL LAN Interface
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1
description WAN Interface
ip address 195.77.XXX.70 255.255.255.248
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 195.77.XXX.65
ip route 192.168.3.0 255.255.255.0 Tunnel0
ip route 192.168.4.0 255.255.255.0 Tunnel1
ip nat inside source route-map salida-fibra interface FastEthernet0/1 overload
access-list 120 deny ip 192.168.1.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 120 deny ip 192.168.1.0 0.0.0.255 192.168.4.0 0.0.0.255
access-list 120 permit ip 192.168.1.0 0.0.0.255 any
route-map salida-fibra permit 10
match ip address 120
Router 2: 2811
version 12.4
service password-encryption
ip cef
no ip domain lookup
multilink bundle-name authenticated
username admin privilege 15 password 7 104CXXXXx13
interface Loopback0
ip address 4.4.4.4 255.255.255.255
interface Tunnel0
ip address 10.10.1.2 255.255.255.0
tunnel source Loopback0
tunnel destination 195.77.XXX.70
interface Ethernet0
ip address 192.168.3.251 255.255.255.0
ip nat inside
ip virtual-reassembly
hold-queue 100 out
interface ATM0
no ip address
no ip route-cache cef
no ip route-cache
no atm ilmi-keepalive
dsl operating-mode auto
interface ATM0.1 point-to-point
ip address 217.127.XXX.188 255.255.255.192
ip nat outside
ip virtual-reassembly
no ip route-cache
no snmp trap link-status
pvc 8/32
encapsulation aal5snap
ip route 0.0.0.0 0.0.0.0 ATM0.1
ip route 192.168.1.0 255.255.255.0 Tunnel0
ip nat inside source route-map nonat interface ATM0.1 overload
access-list 100 permit ip 192.168.3.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 120 deny ip 192.168.3.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 120 permit ip 192.168.3.0 0.0.0.255 any
route-map nonat permit 10
match ip address 120

Hello, thank you for the answer, as to your question, I have no connectivity within the tunnel, whether from Router 1, I ping 10.10.1.2 not get response ...
Now both routers remove the loopback, and the interface tunnel 0 change the tunnel source to "tunnel source " tunnel works perfectly, the problem is when I have to use the loopback. Unfortunately achieved when the tunnel work, this will have to endure multicast, and all the examples found carrying a loopback as' source '... but this is a step back ..
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Internet address is 10.10.1.1/24
MTU 1514 bytes, BW 9 Kbit, DLY 500000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 2.2.2.2 (Loopback0), destination 217.127.XXX.188
Tunnel protocol/transport GRE/IP
Key disabled, sequencing disabled
Checksumming of packets disabled
Tunnel TTL 255
Fast tunneling enabled
Tunnel transmit bandwidth 8000 (kbps)
Tunnel receive bandwidth 8000 (kbps)
Last input 09:04:38, output 00:00:19, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
11101 packets output, 773420 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out

WCCP Redirection on a GRE Tunnel

Similar Messages

Maybe you are looking for