WCCP with Catalyst6500 version 12.2(33)SXH1
recently I deployed WAAS 4.1.1c with Catalyst6500. We have several different L3 vlan interfaces configured as wccp 61/62 redirect in. The L3 vlan interface connected to the direct servers is normal. However, I found that L3 vlan interface connected to internal FWSM outside interface doesn't work well.
I don't know if it's a Catalyst6500 IOS or WAAS issue.
Thanks,
Daniel
Hi Daniel,
Can you please describe wasn't isn't working with the FWSM outside interface? If possible, it would also help to get a copy of the 6500 and WAAS configurations.
Thanks,
Zach
Similar Messages
-
WCCP with Catalyst6500 version 12.2(33)SXI
Hi,
I deployed 2x6500 and 3xWAE in a branch. Problem is when I set wccp on - all traffic is cut off for the interface with service 61. I've ACL considering traffic which have to be redirected but there is no any match in this ACL.
Each WAE is connected to both 6500 (FE, full-duplex). I've also another branch in the same configuration working (but WAE is connected by GE - this is only one difference)
WAAS 4.1.1c
any idea?Darek,
A couple of comments on your configs. I would not use the following configs with a hardware based redirection on a CAT-6K.
int tunnel x
ip wccp 62 redirect in
- As far as I know, this should not work for redirection on a hardware based platform, however, it WILL work on a software based IOS platform.
egress-method negotiated-return intercept-method wccp (on the WAE)
- This should cause your egress traffic to be all prossess by the CPU as it cannot do WCCP-GRE on the SUP. Use Generic GRE egress instead for CAT6Ks. http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v411/configuration/guide/traffic.html#wp1106308
Both of those configs will give you trouble on a hardware based platform. I might recommend that you move away from the tunnel interface if at all possible. As a side note, on the newer ASR-1000 platform, we can do interception on tunnels as well as negotiated return in hardware.
Hope that helps,
Dan -
I have configured a 3560 (122-44 IP Services) switch to communicate WCCP with an WAE-612 v4.1. However the devices don't form WCCP server-client relation with each other.
When I enable "debug wccp all" on the WAE: It complains with:
"2008 Sep 17 13:54:49 CCI-WC-NC-01 wccp: %WAAS-DDBG-7-899998: ISU assignment capability 2
2008 Sep 17 13:54:49 CCI-WC-NC-01 wccp: %WAAS-DDBG-7-899998: wccp2.c:3169:
2008 Sep 17 13:54:49 CCI-WC-NC-01 wccp: %WAAS-DDBG-7-899998: Router cannot support configured capability for assignment method."
WAE-612 is directly connected to the switch through a vlan. I tried GRE and L2 forwarding methods.the wae config and wccp output:
CCI-WC-NC-01#sh run | i wccp
wccp router-list 8 192.168.192.33
wccp tcp-promiscuous router-list-num 8 l2-redirect assign-method-strict l2-return
wccp version 2
CCI-WC-NC-01#sh wccp router
Router Information for Service: TCP Promiscuous 61
Routers Configured and Seeing this Wide Area Engine(0)
-NONE-
Routers not Seeing this Wide Area Engine
192.168.192.33
Routers Notified of but not Configured
-NONE-
Multicast Addresses Configured
-NONE-
Router Information for Service: TCP Promiscuous 62
Routers Configured and Seeing this Wide Area Engine(0)
-NONE-
Routers not Seeing this Wide Area Engine
192.168.192.33
Routers Notified of but not Configured
-NONE-
Multicast Addresses Configured
-NONE-
3560 config and wccp outputs:
CCI-SW-NC-BB-01#sh run | i ip wccp
ip wccp 61 redirect-list 101
ip wccp 62 redirect-list 102
CCI-SW-NC-BB-01#sh ip wccp
Global WCCP information:
Router information:
Router Identifier: 192.168.192.254
Protocol Version: 2.0
Service Identifier: 61
Number of Service Group Clients: 0
Number of Service Group Routers: 0
Total Packets s/w Redirected: 0
Process: 0
CEF: 0
Redirect access-list: 101
Total Packets Denied Redirect: 0
Total Packets Unassigned: 0
Group access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
Service Identifier: 62
Number of Service Group Clients: 0
Number of Service Group Routers: 0
Total Packets s/w Redirected: 0
Process: 0
CEF: 0
Redirect access-list: 102
Total Packets Denied Redirect: 0
Total Packets Unassigned: 0
Group access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
thanks -
I downloaded Version 4 and installed it. At no point did it say that it was not compatible with the version of OS X that I am running (10.4.11) now that it is installed it will not open but it has already up graded from 3.6 so I have lost the lot. How can I download a version of 3.6 so that I can use it again or should I just pack up and use Safari as all I can get from your site is version 4. HELP!!!
Go to this link and find your language:
http://www.mozilla.com/en-US/firefox/all-older.html -
I want to add another management server to our existing SCOM environment. But whenever I run this setup on a new server I get stuck in the window for selecting the OperationsManager database. The database field stays blank and in the OpsMgrSetupWizard log
there are lines that the setup version is not compatible with the database version. But I use the same installer as when I installed the other management servers a year ago.
Maybe there is a newer setup installer? But I can't find it.
[10:42:54]: Error:
:Error:setup version: 7.0.9538.0 is not compatible with database version: 7.1.10226.0
[10:42:54]: Info:
:Info:Using DB command timeout = 1800 seconds.
[10:42:54]: Info:
:Info:isOMDatabase: Read returned true. so far, this is OM DB, not an empty DB
[10:42:54]: Debug:
:Connection was not open. We will try to open it.
[10:42:54]: Debug:
:SqlConnectionReady returned True.
[10:42:54]: Info:
:Info:Using DB command timeout = 1800 seconds.
[10:42:54]: Info:
:Info:isOMDatabase: Read did not return true. The MG is missing. This is not OM DB
[10:42:54]: Info:
:Info:Using DB command timeout = 1800 seconds.
[10:42:54]: Always:
:Azman store table not found in OperationsManagerDW table, assuming this is an not a valid OMDB for empty DB scenario.
[10:42:54]: Info:
:Info:DatabaseConfigurationPage: DB connection attempt completed.
[10:42:54]: Info:
:Info:DatabaseConfigurationPage: DB connection attempt completed.Never mind, found it!
Apparently there was a newer version of SCOM setup in msdn and someone upgraded our existing SCOM environment. Downloaded the new setup, new report viewer controls and a System
CLR Types for Microsoft® SQL Server® 2012 and now it works!! -
I AM TRYING TO OPEN FIREFOX, AND GET A URL MESSAGE: PLATFORM VERSION 8.0 NOT COPATABLE WITH MIN VERSION 7.D MAX VERSI 7.D
If you use ZoneAlarm Extreme Security then disable Virtualization and reinstall Firefox.
*http://kb.mozillazine.org/Browser_will_not_start_up#XULRunner_error_after_an_update
See also:
*[[/questions/880050]] -
I installed a new printer and now Photoshop Elements tells me I can't print. The error message is "The saved printer information is not compatible with this version of Photoshop Elements, or the saved printer is no longer available. You will need to check your printer settings before printing." I have uninstalled and re-installed Photoshop Elements, checked my printer settings and still I can't print a photo.
Hi ,
Please update to PSE 13.1
13.1 has solved this problem.
Refer to this link.
Photoshop Elements Help | Printer errors with Photoshop Elements 13 -
Photoshop CS2: "file not compatible with this version of Photoshop" error
So, I've been working with Photoshop for almost 20 years now, and lately I've been getting this error message on occasion (but not on every file) when I go to open a file I worked on just yesterday: "Could not complete your request because the file is not compatible with this version of Photoshop." I just worked on it yesterday in Photoshop. The file was saved as a PSD, and when I attempt to open it through Painter IX, that program tells me that it's not a Photoshop document. Why can't I open this file anymore, and why is it giving me this error message when I don't have Norton AntiVirus installed, and my 'maximize PSD and PSB file compatibility' is set to 'always'??
Does anyone have an idea on how I can open my file? How can I get around this, and how do I prevent it from happening again?
OS: OSX 10.4.11
Photoshop CS2
Info:
Kind: Adobe Photoshop file
Size: 394.4MB
Created: December 13, 2007
Modified: Yesterday at 3:54 PMThis is the boilerplate text I use in connection to saving to a network (please NOTE the part where it explains that normally, it does work, but that it is impossible to troubleshoot someone else's network remotely, and that's why it's not supported by Adobe):
If you are opening files over a network or saving them to a network server, please
cease and desist immediately
in the event you are currently experiencing problems with one or more files.
Working across a network is not supported.
See:
http://www.adobe.com/support/techdocs/322391.html
Copy the
CLOSED file from your server to your local hard disk, work on it, save it again to your local hard disk, close it, and copy the closed file back to the server.
Of course, the fact that Adobe does not support working across a network does not necessarily mean it won't work. It should.
Adobe's position is that there are too many variables in a network environment for them to guarantee that everything will work correctly in every network, especially given the fact that if something does
not work properly, it's probably the network's fault, and Adobe has no way of troubleshooting your network.
If you can't work locally, you are on your own, and if something happens, you're on your own. If you must work from a server, make sure your network administrator is a competent professional.
When problems arise, a lot of valuable work can be lost. -
how do i remove the songs from my iphone used to be easy with old version of itunes just unticked them but cant seem to find it any where on new version
how do i remove the songs from my iphone used to be easy with old version of itunes just unticked them but cant seem to find it any where on new version
-
My iPhone 4 will not sync my new voice memos from the "Voice Memos" app to my computer. This is frustrating, should not be so hard, can someone please help. I use PC with windows 7 with iPhone version 6.1.3 and iTunes most recent. Thanks.
In the Music tab of iTunes, do you have 'Include Voice Memos' checked?
-
UDI-00018: Data Pump client is incompatible with database version 11.2.0.1
Hi
I am trying to import data in Oracle 11g Release2(11.2.0.1) using impdp utitlity and getting below errror
UDI-00018: Data Pump client is incompatible with database version 11.2.0.1.0
Export dump has taken in database with oracle 11g Release 1(11.1.0.7.0) and I am trying to import in higher version of the database. Is there any parameter I have to set to avoid this error?AUTHSTATE=compat
A__z=! LOGNAME
CLASSPATH=/app/oracle/11.2.0/jlib:.
HOME=/home/oracle
LANG=C
LC__FASTMSG=true
LD_LIBRARY_PATH=/app/oracle/11.2.0/lib:/app/oracle/11.2.0/network/lib:.
LIBPATH=/app/oracle/11.2.0/JDK/JRE/BIN:/app/oracle/11.2.0/jdk/jre/bin/classic:/app/oracle/11.2.0/lib32
LOCPATH=/usr/lib/nls/loc
LOGIN=oracle
LOGNAME=oracle
MAIL=/usr/spool/mail/oracle
MAILMSG=[YOU HAVE NEW MAIL]
NLSPATH=/usr/lib/nls/msg/%L/%N:/usr/lib/nls/msg/%L/%N.cat
NLS_DATE_FORMAT=DD-MON-RRRR HH24:MI:SS
ODMDIR=/etc/objrepos
ORACLE_BASE=/app/oracle
ORACLE_HOME=/app/oracle/11.2.0
ORACLE_SID=AMT6
ORACLE_TERM=xterm
ORA_NLS33=/app/oracle/11.2.0/nls/data
PATH=/app/oracle/11.2.0/bin:.:/usr/bin:/etc:/usr/sbin:/usr/ucb:/home/oracle/bin:/usr/bin/X11:/sbin:.:/usr/local/bin:/usr/ccs/bin
PS1=nbsud01[$PWD]:($ORACLE_SID)>
PWD=/nbsiar/nbimp
SHELL=/usr/bin/ksh
SHLIB_PATH=/app/oracle/11.2.0/lib:/usr/lib
TERM=xterm
TZ=Europe/London
USER=oracle
_=/usr/bin/env -
I have an old iPhone 3Gs with software version 4.3.5, I am trying to use it again, and it works fine, but I have not been able to update the software. Every time I try, I get the following message:
"there was a problem downloading the software for the iPhone, the network connection could not be established". This happens even though I have a working internet connection.
Besides that, all the other functions work properly, even synchronize apps and library.
Will I be able to update the software?look around the forum tons of people repport that they can't update
makes you suspect that apples update servers can't meet the depand of too many users
trying to update at once -
I am trying to install a registered copy of Photoshop Lightroom that I never installed on my Apple iMac with software version 10.10.
I get the message “Adobe Lightroom 1. Cannot be installed on this disk because a newer version of this software already exists on this disk”
If it is here – I cannot find it anywhere, and I don’t believe that I ever installed it.
I have ordered the upgrade to Lightroom 5.0 and figured that I should install Lightroom 1.0 first.
How can I solve this problemActually when LR 5 starts for the first time after it is installed it will have a dialog to Buy, Try or Enter a serial number. You select Enter a serial number and enter the LR 5 serial number first and then because it is an upgrade serial number it will ask for the serial number of a Previous version. You then enter the LR 1 serial number.
-
I've got a new iPad and am trying to do an iCloud backup but keep getting the following message: no iCloud backups are compatible with the version of iOS (6.1.3) on this iPad.
How do I restore info from iCloud onto my new device?You would have to update your device first, before you can restore your iPad from your backup. Resolution: set it up as anew device, then update your device to the latest version "Settings > General > Updates", then reset your device again "Settings > General > Reset > Erase All Content and Settings" and then after the iPad restarts again, choose to restore your device from your backup.
-
[There is a link below from where software can be downloaded and after installing this you will see that it is not compatible with any version of Mozilla Firefox of any Window version (7, XP).]
[http://ftp://ftp.hp.com/pub/softlib/software10/COL20395/dj-56929-3/HP_Smart_Web_Printing_v4.6.exeIt is up to HP to make that program compatible with Firefox.
That application last worked in Firefox 3.5, but HP was always very lax in updating it for a new version of Firefox. Usually they didn't bother to update it until like halfway through the "run" of a particular Firefox version. It worked for like 6 months and then a new version of Firefox was released, and it didn't work for like 6 months until HP got around to fixing it - then the cycle repeated.
Maybe you are looking for
-
Customer automatic clearing with down payment
Dears, kindly help me regarding the following; we have the following case; customers come to store, choose a product, pay part of the price and the rest at home after delivery. I want to make automatic clearing for invoices, down payments, and
-
One of our team has created a PDF from MS PowerPoint. In Acrobat Pro 9 they subsequently added a page to the PDF and added an MP4 file to it via the Multimedia > Video Tools option. Everything works well except that the video is rendered at a larger
-
Enterprise manager agent not running
Hi all, Oracle 11g Windows 2008 I just installed two databases on the same server. The one's EM is running fime no prob. The other, the EM doesn't want to open completely it says: Enterprise Manager is not able to connect to the database instance. Th
-
Need help with basic program.....!
I've to write a program that generates a random number, which the user has to try and guess, after each guess they're told whether it's too high or too low etc., I've gotten this far, however, the user has only 10 guesses.... In my program I've used
-
Redeploying classes and EJBs into a running, external WeblogicServer6.1 application
Is it possible to debug, edit, compile and deploy the new class and/or EJB using jBuilder5 on Win2k and WeblogicServer6.1 on Solaris WITHOUT restarting the app server? Is there solid documentation, where? I can debug, but the 'documentation' concerni