WCS 6.0 client traffic reports

I've looked around in the reports trying to find one that generates the Client Traffic report on the Home page under the Client tab. It is just a plain and simple graph that shows how much bandwidth has been used. I've only seen reports that show how much bandwidth a client has used or each individual wlc. I just need an overall bandwidth usage. Does anyone know how to create this graph via Reports or any other way?
Thanks
Brock

How about this:
Reports > Report Launch Pad > Client > Client Summary > Client Summary Report Details
Customize the report and only include:
Number of Sessions - Required
Number of Users - Required
Total Traffic (MB)
Total Throughput (Mbps)

Similar Messages

WCS v7.0 - Client Traffic Stats

Hi,
I have a demo license version of WCS v7.0 set up for a customer trial which is controlling a WLC-4402 and approx 10 access points.
Everything is working normally and as I would expect apart from the 'Client Traffic' reporting. When I check the graphs on 'WCS Home' > 'Client' tab, the Client Count graphs are working and showing correct data but the Client Traffic graph is showing 0Kbps. I have also tried running a Client Traffic report and this also shows a graph with 0Kbps. I know that there are a number of users associated and passing traffic but I cannot find any reason why this is not recording and reporting correctly.
Does anyone have any pointers or advice for what to check next?
Many thanks,
Paul.

Hi Paul,
That's exactly the issue as v1 doesn't have the ability to poll objects which have 64 bit counters which the client traffic metrics are.
Change the version to SNMP v2 from WCS
Configure --> Controllers --> Click on the IP of the WLC ---> Under 'SNMP parameters' --> click save.
Wait for few hours & you should start seeing the graph getting populated.
Ram

Prime Infrastructure 2.1 & Client Traffic Report

Hi,
I know I can get the user Traffic & average session throughput as example over the Top 5 SSIDs and then I can create an overview for the
needed SSID with the needed columns Traffic & Avg. Session Throughput.
I checked the option to get this overview with a report and I tried several client reports but I don´t find any report type which provide me this
information : Client MAC , AP ,Traffic & Avg. Session Throughput.
Is there a possibility to generate a report which includes above information ?
Thanks

Hi,
here is an update:
There are more than one Report you need to start to get data for Device, FAN, Power Supply, Module - look at these reports:
Report > Report Launch Pad > Device > Inventory
Report > Report Lauch Pad > Device > Wired Detailed Device Inventory
Report > Report Lauch Pad > Device > Wired Module Detail > Wired Module Detail Report Details
SFPs and GBICs cannot be reported til now - there are working on it.
br,
chris

Generation of Client summary report on WCS

Hi,
I have four WLCs running the IOS version 7.0 at different locations. All these WLCs are joined to the WCS at one location.
I am trying to generate the client summary report. But i am not able to generate the report as per the requirements.
Please let me know is it possible to generate the client summary report for each controller.(i.e) The report providing the details of the users at each location. If so, Please let me know the procedure.

Hi,
Client summary cannot be narrowed down to Controller ip.. However, the "Client session report" will help you out in getting the report per Controller and this gives the client TX, RX and you can custpmize it as well!!
here is the link to do it..
http://www.cisco.com/en/US/docs/wireless/wcs/7.0/configuration/guide/7_0reps.html#wp1135765
lemme know if this answered ur question!!
Regards
Surendra

Cisco WCS client count report - client count figures cumulative or concurrent?

Hi,
Just want to clarify the "assoicated client count" and "Authenticated client count" values from WCS Client count report concurrent or cumculative?
The client count report in excel format:
Total Client Count
Total Count
Event Time
Associated Client Count
Authenticated Client Count
total
Sun Oct 12 23:59:59 HKT 2014
3992
3854
total
Mon Oct 13 23:59:59 HKT 2014
7838
7289
total
Tue Oct 14 23:59:59 HKT 2014
7724
7124
total
Wed Oct 15 23:59:59 HKT 2014
6849
6336
total
Thu Oct 16 23:59:59 HKT 2014
5908
5530
total
Fri Oct 17 23:59:59 HKT 2014
1240
1228
total
Sat Oct 18 23:59:59 HKT 2014
1040
1031
Client Count
AP Name
Base Radio MAC
Event Time
Associated Client Count
Authenticated Client Count
AP-EDHB-018
08:1f:f3:23:23:10
Mon Oct 13 23:59:59 HKT 2014
160
157
AP-EDHB-018
08:1f:f3:23:23:10
Tue Oct 14 23:59:59 HKT 2014
121
120
AP-EDHB-018
08:1f:f3:23:23:10
Wed Oct 15 23:59:59 HKT 2014
95
95
AP-EDHB-018
08:1f:f3:23:23:10
Thu Oct 16 23:59:59 HKT 2014
94
94
AP-EDHB-018
08:1f:f3:23:23:10
Fri Oct 17 23:59:59 HKT 2014
6
6
AP-EDHB-018
08:1f:f3:23:23:10
Sat Oct 18 23:59:59 HKT 2014
3
3
AP-EDHB-019
08:1f:f3:23:24:30
Sun Oct 12 23:59:59 HKT 2014
38
38
AP-EDHB-019
08:1f:f3:23:24:30
Mon Oct 13 23:59:59 HKT 2014
113
110
AP-EDHB-019
08:1f:f3:23:24:30
Tue Oct 14 23:59:59 HKT 2014
110
109
AP-EDHB-018 have 160 assoicated client count reported. Really mean there were 160 wireless client assoicated at a moment or there were a totally 160 connected at that day?
Any idea?
Dick

Hi Kayle,
Thanks for the response. I think you are talking about this in the above.
Reports > Report Launch Pad > Client > Client Count > Client Count Report Details
then
AP by Floor Area and select "All Campus", "All Building", "All Floor"
By doing this I get 700+ APs daily client count in graphical (pdf) view and need to go through manually each graph to identify the top 50, top 100 in a given day.
Is it possible to only filter the top 50, 100 APs ?
I would like see my daily report gives something similar to the below
AP Name    Max Client Count
AP01               96
AP02               83
AP50               20
Would it possible to get something like this from WCS reports ?
Thanks
Rasika

WCS reponds slow when generating the Client Association reports

Hello,
I have set a Wireless Network in of our client's corporate office - which consists of one WLC4404, 42 x 1131AG Access Points. WCS is used to mainly to monitor the AP reachability and Client Association and Deassociations from the WLAN.
When i click on Run Now of the Client Association reports; the report is generated successfully. But when i try to view other pages such as Monitor>Network Summary - the WCS stops responding and it takes approximately 7 mins to display the Monitor>network Summary page. At this time i have observed that the server is reachable during the continous ping and the Server CPU utilization remains to 8% and Memory utilization remains to 1.56GB.
Error Message: Error getting dataa from Server. Make sure you have connectivity and the Server is UP.
Server used is a Standard Server HP Proliant ML110 with 1.86GHz Intel Xeon CPU and 2GB RAM. Operating System used is Win 2003 Server with SP1.
Please can one help me solving this problem.
Regards,
Keshava Raju

Sorry, i missed out to mention - WCS V4.1 is used for monitoring the WLAN.

Prime Infrastructure 2.1 Client Statistic Report Issues

Hello Community,
I hope you can help with a couple of issues I am seeing on Prime Infrastructure 2.1, running an evaluation 60 day license.
My PI 2.1 build is currently managing a WLC 5508 running 7.4.121.0, which has been added successfully. No configuration changes were applied to the WLCs, other than SNMP community. No AVC or medianet configuration is applied.
When looking in the 'Operate>Client and Users' dashboard; I can see connected clients and if I select one of them, I can see further details like session, security and client statistics (showing traffic and 802.11 metrics). These are the table views that show current values, however, further down I see graphs but they do not contain any information for RSSI, SNR or traffic sent & received (packets or bytes).
Question: Should I see this information under an evaluation license and if so, what could be stopping it?
Also, when I run the reports 'Report>Report Launch Pad' and select 'Client>Client Traffic' or 'Client>Client Throughput' the resulting report contains 0 bps, when I select 'Report By' AP by Floor Area. I have created a single floor area and placed three access points into it.
Out of interest if I do a report of the same type using 'Report By' All or AP by Controller, I do see traffic graphs for 3 out of 333 access points. Just not the access points that are in my floor area. Also the amount of traffic utilization is tiny (less than a kbps) for a WLC with 800 users.
For a 'Client>Client Count' report using AP by Floor Area, I do see the client numbers connected to the WLC/APs in my configured floor area.
Question: Should I see reports for client traffic and throughput under an evaluation license for floor areas and if so, what could be stopping it?
I have checked the background task and the 'Client Statistics' task is enabled and run time is being updated.
Kind regards,
Ian

Hi,
here is an update:
There are more than one Report you need to start to get data for Device, FAN, Power Supply, Module - look at these reports:
Report > Report Launch Pad > Device > Inventory
Report > Report Lauch Pad > Device > Wired Detailed Device Inventory
Report > Report Lauch Pad > Device > Wired Module Detail > Wired Module Detail Report Details
SFPs and GBICs cannot be reported til now - there are working on it.
br,
chris

WCS 7.0.164.0 Report by vendor (device type)

WCS 7.0.164.0
I have been asked to produce a client’s report that shows all different vendors (devices type). We have about 10000 users in our system on about 3000 APs (light version) I created a client summary report but encountered some limitations:
If I select any time period over 6 hours, I get the message “The report you are trying to generate contains more than the supported number of records (10000). Change the report criteria to generate a report with fewer records”
If I select a time period of 6 hours or less, I get the report including vendor statistics. Is there any way to differentiate within the vendors by device type? For example instead of the vendor apple, get apple-iPhone, apple-iTouch, apple-laptop, etc.
I would like the ability to create my own reports, by I don’t think it is possible on the Version I’m running. All reports can be customized up to a point, but you still get information you might not care for.
Thanks for any information to overcome these issues.
Jorge Jiles.

Hi Jorge,
It looks like such a level of granularity may not be achievable yet.
Should you need such a feature to be evaluated for potentially being included in future software releases, I would recommend to contact your local Cisco account team.
They should be able to follow up and submit a product enhancement request (PER).
Business units will evaluate PERs and, if feasible for the market, they may consider implementing such an enhancement in future versions of the SW/HW.
Regards,
Fede

Prime 2.1 - Client count report based on ssid

Dear All,
Is it possible to extract the reports of client count per ap based on ssid..?
Like, AP Name (eg., 2ndFloorAP) --> SSID (Test)--> Client count for past 1day, 1 week, 1 month etc.
As of now i could see overall client count of an ap from prime not based on SSID (under device work center --> unified ap --> client over time --> client count on ap / client traffic on ap)

Hi Prasan,
Revisiting this issue, if you have your APs assigned to specific campus/building for your company, you can drill down to the specific AP and SSID that you want for that client count. The options that I used to run a report for one AP for one location that we have is as follows:
report title: <enter applicable name for report>
report by: AP by floor area
report criteria: choose edit and search for the location/building/campus and then the specific AP that you want from those fields. Then choose select.
Once back at the report screen you can set the next options:
connection protocol: select from drop down what you want if it is all clients, all wireless, etc.
The next drop down should allow you to select the specific SSID to what you want based upon the individual AP. Followed by the report time afterward. This report will output as a line graph showing the total number of clients based upon your search criteria and time frame. If you want to research client counts and see their mac address and IP ranges then you are limited to only seeing the current associated clients from the operation > work center flow while viewing the specific AP. Hope that helps.
Regards,
Brandon

Show dot11 statistics client-traffic

I'm trying to interpret output from the 'show dot11 statistics client-traffic' command in autonomous IOS version 15.2(4)JB4 on a 3600-series access point. Finding a detailed description of each data point being reported has been very difficult - c'mon Cisco! For my purposes I'm most interested in what is being reported in the 'Retry' and 'RSSI' fields. It seems like RSSI in dBm is being reported but I'd like confirmation from someone who knows because in older versions of IOS it seems like this value might have been a percentage value on a scale of 0 to 100% with 0 being -113dBm and 100 being -10dBm.
Here is a sample of the output from my access point:
SURVEY_AP1#show dot11 statistics client-traffic
Dot11Radio0: -- Client Statistics
---Clients 0 AID VLAN Status:S/I/B/A Age TxQ-R(A) Mode Enc Key Rate Mask Tx   Rx   BVI   Split-ACL Client-ACL L2-ACL
                 RxPkts KBytes Dup Dec Mic   TxPkts KBytes Retry RSSI SNR
               (Client) MaxPri DefUniPri DefMultPri WiredProt
               IP Address      Pauses Idle   RateTx   RateDataTx   RSC
MVL Req=0, In=0
Video Report: Cnt Rate Retries/Tot
8021x auth in prog 0 allowed 0
Dot11Radio1: -- Client Statistics
---Clients 0 AID VLAN Status:S/I/B/A Age TxQ-R(A) Mode Enc Key Rate Mask Tx   Rx   BVI   Split-ACL Client-ACL L2-ACL
7cd1.c379.2d10    1    0 30 40144 000 03E 60   0-0 (0) 3F80 200 0-10 00FFFFFFFF000000000 0817 00C
                 RxPkts KBytes Dup Dec Mic   TxPkts KBytes Retry RSSI SNR
7cd1.c379.2d10      294     25   59   0   0      155      16     98   43 45
              Agr TxLt   TxRP   St ACQ/TW TxACQ Stats
7cd1.c379.2d10 p0 64 138 0 0 1 1 0 243 243 0 0 0
7cd1.c379.2d10 p1 20 30 0 0 1 1 0 0 0 0 0 0
7cd1.c379.2d10 p2 20 30 0 0 1 1 0 0 0 0 0 0
7cd1.c379.2d10 p3 20 138 0 0 1 1 0 0 0 0 0 0
7cd1.c379.2d10 p4 20 30 0 0 1 1 0 0 0 0 0 0
7cd1.c379.2d10 p5 20 30 0 0 1 1 0 0 0 0 0 0
7cd1.c379.2d10 p6 20 30 0 0 1 1 0 10 10 0 0 0
7cd1.c379.2d10 p7 20 30 0 0 1 1 0 5 5 0 0 0
    Tx Params Pri BA TxLt AggrSz MaxL AvgL
7cd1.c379.2d10   0   4 138   64 65460 111
7cd1.c379.2d10   1   0 30   20 65460    0
7cd1.c379.2d10   2   0 30   20 65460    0
7cd1.c379.2d10   3   0 138   20 65460 1500
7cd1.c379.2d10   4   1 30   20 65460    0
7cd1.c379.2d10   5   1 30   20 65460    0
7cd1.c379.2d10   6   0 30   20 65460    0
7cd1.c379.2d10   7   0 30   20 65460    0
               (Client) MaxPri DefUniPri DefMultPri WiredProt
7cd1.c379.2d10             0          0           0          0
               IP Address      Pauses Idle   RateTx   RateDataTx   RSC
7cd1.c379.2d10 192.168.0.100   00004 000000      0      0 [0]0x10C [6]0xA7
    Block Ack Pri, Rcv Wind Timeout SeqNum Held, Xmt Wind Timeout
7cd1.c379.2d10   0        64        0    D20    0        64        0 4, 0 0 0
7cd1.c379.2d10   4                                        0        0 1, 0 0 0
7cd1.c379.2d10   5                                        0        0 1, 0 0 0
    LBF             Indx     BfPkts   NbfPkts BfTmr    PktCnt
7cd1.c379.2d10 RIA    1         18       130      4        17
MVL Req=1, In=1
Video Report: Cnt Rate Retries/Tot
8021x auth in prog 0 allowed 0
SURVEY_AP1#
Thanks in advance for any assistance.

You want the RSSI (Radio Signal Strength Indicator) and the SNR (Signal-to-Noise Ratio) of a particular client?
You have to run one or two commands then. The first one is "sh dot11 s". This will show you the wireless MAC address of a client. Copy-n-Paste the MAC address of your choice and use the command "sh dot11 s ".
Does this answer your question?
Please don't forget to rate useful posts. Thanks.

Strange NIC traffic reporting with Windows Intune updates

Hi
I've been building out a test environment for some Intune deployments we have in the works, and have encountered some weirdness in the Intune traffic reporting on both the NIC of the guest client VM with Windows 7, the virtual NIC it connects to on the Server
2008 R2 + TMG VM on a Hyper-V virtual network, as well as the Internet NIC on the TMG VM. TMG has had the Intune script from Paul Bourgeau's blog post applied to it as well.
While traffic from Windows Update, Internet Explorer etc are all reflected accurately, I've repeatedly watched Intune VMs pull down 50-60 updates without having an impact on the bytes sent/received on all three of the NICs above, the only place I'm really
seeing the traffic being reported is via my ISP.
I initially tried running this against a single NIC TMG VM, but noticed that a bunch of the connections were bypassing the proxy, but now that I have completely isolated the client from my network, forcing it through a double NIC TMG VM, I am confident that
it isn't finding a way to bypass that VM completely.
Any suggestions for what I should be looking for to help troubleshoot the traffic that I should be seeing reported, but am not? Everything is pointing to this traffic still bypassing the cache completely, which I know could be a TMG config issue, but the
NIC reporting is just weird, especially as it only seems to be the Intune traffic that is MIA.
thanks
Mark

As nobody has answered, if the problem still exists I would recommend that you call Intune support.
You will find your local Intune support number here
http://technet.microsoft.com/en-US/jj839713.aspx
Gerry Hampson | Blog:
www.gerryhampsoncm.blogspot.ie | LinkedIn:
Gerry Hampson | Twitter:
@gerryhampson

How to generate web traffic report on SharePoint 2013?

Hello All,
I am working on Intranet in SharePoint 2013 On Premise.
There are functionalities like Poll, Survey, Event, Announcements etc.
Now there is a requirement to create web traffic report for all these functionality. How should I generate web traffic report for all these?
Thanks in Advance.

Hi Darsh,
Here is the out of box analytic reports you can view. Please refer to the following article.
SharePoint 2013 Analytics A Big Step Backward
New Analytics in SharePoint 2013
Please mark it answered, if your problem resolved or helpful.

How to get a summarized mail traffic report in exchange 2013

Hi all
How to calculate the exchange 2013 SMTP mail traffic in terms of hour,day,month,top senders,largest message and top recipients list . Same time we would like to have those summarized mail traffic report for all the mailbox servers in the form of graphical
view as well as in a csv file ?
Please all of us share your thoughts and possibilities .
Regards
S.Nithyanandham
Thanks S.Nithyanandham

You may calculate hourly email traffic using "Message Tracking Logs and Log Parser".
I would like to refer you on this well explained article that will assist you step-wise to implement in your working environment : http://exchangeserverpro.com/calculate-hourly-email-traffic-using-message-tracking-log-parser/
Moreover, if you wish to achieve this goal automatically, you may also consider on this automated application (http://www.exchangereports.net/) that provides a deep-view of email traffic report in real time at
granular level.

Client-Auth reports: HTTP4030: Timeout while waiting for client certificate

Hello,
I'm having problems with the certificate authentication in my Sun Java System Web Server Enterprise Edition 6.1: I have created an ACL in the SJWS that asks for a client certificate when the user goes to a specific URI:
acl "uri=/server1/myaction.do";
authenticate (user) {
method="ssl";
deny (all)
user = "admin";
It works great and, when the user goes to "/server1/myaction.do" (we are using Internet Explorer 7 as Web browser), the window for selecting the client certificate appears:
- If the user selects a certificate that doesn't require password, everything works fine.
- The problem comes when the certificate is configured in Internet Explorer for asking for a password every time it is accessed. Once the user has selected the password protected certificate, the window for typing the password appears, but if the user doesn't type it and click OK IN LESS THAN 5 SECONDS (I've timed it), the following messages appear in the SJWS logs:
[28/Nov/2007:09:25:05] failure ( 2055): for host 10.0.145.11 trying to GET /server1/myaction.do, Client-Auth reports: HTTP4030: Timeout while waiting for client certificate.
[28/Nov/2007:09:25:05] security ( 2055): HTTP4290: get_auth_user_ssl: client passed no certificate.
I tried to add the following two lines to the magnus.conf file of the SJWS, but nothing changed:
SSLClientAuthTimeout 240
AcceptTimeout 3600
Has anyone experienced something similar? Any little piece of advice would be greatly appreciated.
Thank you very much in advance,
Carlos.

This is fixed in Web Server 7.0 update 2. Please migrate/upgrade to Web Server 7.0 update 2. Sorry for the inconvenience.

Client-Auth reports: HTTP4031: Unexpected error receiving data: -5938

I am trying to deploy the clientcert sample applcation that comes with the platform edition of SunOne V7.
I have used openssl as a CA and have created client and server certs.
I get the following problem.
     Sun ONE Application Server - HTTP Status 403 Error
     Access to the specified resource (Access to the requested resource has been denied) has been forbidden.
     Type: Status Report
     Message: Access to the requested resource has been denied.
As can be seen from the server.log below, some form of authentication succeeds:
     [12/Aug/2004:08:56:11] FINE ( 2392): X.500 name login succeeded for : CN=tweekes, O=tester, C=ie
Note, common name is that of my client cert.
However there is a severe error:
     [12/Aug/2004:08:56:09] SEVERE ( 2392): for host 169.254.111.12 trying to GET /cert, Client-Auth reports: HTTP4031: Unexpected error receiving data: -5938
Also, HTTPS works with server side authentication and I signed both client and server certs with same private "CA" certification.
Question: Do I need any special extentions in the certs for use with SSL?
Thanks in advance.
server.log fragment:
[12/Aug/2004:08:56:09] FINE ( 2392): for host 169.254.111.12 trying to GET /cert, ntrans-j2ee reports: directory listing for context "/cert"
[12/Aug/2004:08:56:09] FINE ( 2392): Attaching to JVM thread service-j2ee-4
[12/Aug/2004:08:56:09] FINE ( 2392): context = StandardEngine[null].StandardHost[server1].StandardContext[cert]
[12/Aug/2004:08:56:09] FINE ( 2392): contextPath = /cert
[12/Aug/2004:08:56:09] FINE ( 2392): wrapper = null
[12/Aug/2004:08:56:09] FINE ( 2392): servletPath = null
[12/Aug/2004:08:56:09] FINE ( 2392): pathInfo = null
[12/Aug/2004:08:56:09] FINE ( 2392): SingleSignOn[server1]: Process request for '/cert'
[12/Aug/2004:08:56:09] FINE ( 2392): SingleSignOn[server1]: Checking for SSO cookie
[12/Aug/2004:08:56:09] FINE ( 2392): SingleSignOn[server1]: SSO cookie is not present
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Security checking request GET /cert
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Checking constraint 'SecurityConstraint[clientcert security test]' against GET --> true
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Subject to constraint SecurityConstraint[clientcert security test]
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Calling checkUserData()
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: User data constraint has no restrictions
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Calling authenticate()
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Looking up certificates
[12/Aug/2004:08:56:09] FINEST ( 2392): Requesting client certificate from core.
[12/Aug/2004:08:56:09] SEVERE ( 2392): for host 169.254.111.12 trying to GET /cert, Client-Auth reports: HTTP4031: Unexpected error receiving data: -5938
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: No certificates included with this request
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Failed authenticate() test
[12/Aug/2004:08:56:09] FINE ( 2392): for host 169.254.111.12 trying to GET /cert, ntrans-j2ee reports: directory listing for context "/cert"
[12/Aug/2004:08:56:09] FINE ( 2392): Attaching to JVM thread service-j2ee-5
[12/Aug/2004:08:56:09] FINE ( 2392): context = StandardEngine[null].StandardHost[server1].StandardContext[cert]
[12/Aug/2004:08:56:09] FINE ( 2392): contextPath = /cert
[12/Aug/2004:08:56:09] FINE ( 2392): wrapper = null
[12/Aug/2004:08:56:09] FINE ( 2392): servletPath = null
[12/Aug/2004:08:56:09] FINE ( 2392): pathInfo = null
[12/Aug/2004:08:56:09] FINE ( 2392): SingleSignOn[server1]: Process request for '/cert'
[12/Aug/2004:08:56:09] FINE ( 2392): SingleSignOn[server1]: Checking for SSO cookie
[12/Aug/2004:08:56:09] FINE ( 2392): SingleSignOn[server1]: SSO cookie is not present
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Security checking request GET /cert
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Checking constraint 'SecurityConstraint[clientcert security test]' against GET --> true
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Subject to constraint SecurityConstraint[clientcert security test]
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Calling checkUserData()
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: User data constraint has no restrictions
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Calling authenticate()
[12/Aug/2004:08:56:09] FINE ( 2392): Authenticator[cert]: Looking up certificates
[12/Aug/2004:08:56:09] FINEST ( 2392): Requesting client certificate from core.
[12/Aug/2004:08:56:11] FINEST ( 2392): Processing login with credentials of type: class sun.security.x509.X500Name
[12/Aug/2004:08:56:11] FINE ( 2392): Processing X.500 name login.
[12/Aug/2004:08:56:11] FINEST ( 2392): Certificate realm setting up security context for: CN=tweekes, O=tester, C=ie
[12/Aug/2004:08:56:11] FINE ( 2392): X.500 name login succeeded for : CN=tweekes, O=tester, C=ie
[12/Aug/2004:08:56:11] FINE ( 2392): Authenticator[cert]: Authenticated 'CN=tweekes, O=tester, C=ie' with type 'CLIENT-CERT'
[12/Aug/2004:08:56:11] FINE ( 2392): SingleSignOn[server1]: Registering sso id '6264FF86CB3151E572951CB77D0C515F' for user 'CN=tweekes, O=tester, C=ie' with auth type 'CLIENT-CERT'
[12/Aug/2004:08:56:11] FINE ( 2392): Authenticator[cert]: Calling accessControl()
[12/Aug/2004:08:56:11] FINEST ( 2392): PRINCIPAL : CN=tweekes, O=tester, C=ie hasRole?: staffmember
[12/Aug/2004:08:56:11] FINEST ( 2392): PRINCIPAL TABLE: {staff=[staffmember], C=ie, O=tester, CN=tweekes=[staffmember]}

The below one is the correct configurations
<If $uri =~ "/my(/passo.*)">
NameTrans fn="restart" from="$uri" uri="/my/jsp$1"
</If>
<Object ppath="/my/jsp/passo/*">
PathCheck fn="get-client-cert" dorequest="1"
</Object>

WCS 6.0 client traffic reports

Similar Messages

Maybe you are looking for