WCS and Controller upgrade questions

Hi,
with the WCS should I install both the EXE file and the BIN fil or just the BIN file?
Also, for upgrading the Controllers where can I find the ER file. I have downloaded the 4.2.209.0 image but, can't find the 4.2.205.0 ER.aes. Does anyone know where this is?
where on the controller can I tell if I already have the ER file?
Thanks, Pat.

Hi Patrick,
The link which i posted is for 4404.. for 4402 here is the link..
http://www.cisco.com/cisco/software/release.html?mdfid=279911193&flowid=7586&softwareid=280926587&release=4.2.112.0%20BOOT&rellifecycle=&relind=AVAILABLE&reltype=all
The latest ER that we hav for 4402 is 4.2.112..
Q1>> To get the software image I goto wireless, Wireless LAN Controllers,  standalone Controllers, Cisco 4400 Series Wireless LAN Controllers,  4402, Software on Chassis hten Wireless LAN Cotroller software, but  don't see the ER file.
ANS - Yes you are right.. the above is the procedure to download the image.. "ER is nothing but the BOOT IMAGE, if you click on BOOT then the image will pop up as ER, the non BOOT will be in .aes format or something..
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

Similar Messages

  • WCS vs Controller License Question - 5500 series.

    In the WCS License Center, there are two sets of license options: WCS and Controller. Am I to understand correctly that:
    - WCS License count is how many APs can be monitored by WCS?
    - Controller License count is how many APs can be connected to a WLC?
    Thanks!
    -Robert

    Think of each controller license as independent license. Although you have 2 AP licenses at 25 each you can aggregate 50 access points to the controllers (25 each). This would of course negate full redundancy.
    But you can steer access points incase of failure in the above example.
    Suppose you have 30 access points ( 15ap location 1 and 15ap location 2). You are over 5 access points over for full redundancy.
    Suppose location 1 is a higher priority then location 2 and you want to make sure you have all the aps up at location 1. You can add a priority to the access points at location 1 so they connect to the controller before aps at location 2.
    Just an fyi

  • HDD and RAM Upgrade Questions...

    I am thinking about upgrading my HDD and memory. My computer is a Qosmio X870-BT3G23. HDD is about 1TB and also have 12GB RAM. I am not sure how to upgrade my RAM as I heard the other 2 memory slots are not user accessable. How would I go about upgrading HDD and transfer all my stuff over? I think my computer has slots for 2 HDDs, but not sure... Thoughts on both HDD and RAM upgrade appreciated 
    Qosmio X870-BT3G23

    Skeet, here are the SPECIFICATIONS for your machine if you have not seen them.  And on pages 44-53 of your User's Guide is a very thorough description of the adding memory process. As far as transferring files are concerned, at the Start screen, type Easy Transfer, hit Enter and follow instructions.
    The specifications indicate you can have 16GB memory in the two accessible memory slots without concerning yourself about the 2 hidden slots. I personally can't imagine why anyone could need more than 16GB memory and 1TB HDD but, of course, that's your call.
    C.B.
    Toshiba Sat. C75D-B7260 Win 8.1 64 Bit--Toshiba Sat. L775D-S7132 Win 7 HP SP1 64 Bit and Win 10 PRO Technical Preview--Toshiba Sat. L305-S5921 Win Vista SP2 32 Bit

  • Macbook 7.1 (mid-2010) RAM and hdd upgrade questions!

    Hello!
    In a bit of impulsiveness, I have just acquired a Apple laptop: a lightly used Macbook 7.1 (released mid-2010 and discontinued, 2.4GHz Core 2 Duo). This is my first Apple computer!
    I want to upgrade just a wee bit to squeeze a bit more performance out of what is currently probably a mid to low end laptop. Two questions:
    1) I know this Macbook takes 1066 MHz DDR memory. But I have two 2 GB sticks of 1333 MHz PC3-10600 DDR3 SODIMM. Can I put those in? Or do I have to get 1066 sticks?
    2) I'd like to put a 7200 rpm hdd in it. Will there be any potential issues with heat? (I'm assuming a 7200rpm drive generates more heat than a 5400rpm drive.)
    Thanks!!!!

    Faster RAM will have a great chance to lead to problems. If it works it will not be noticeably faster; The bus speed is still 1066. Ram being cheap I would either put in more ram and not faster ram, buy from high reputation suppliers like Crucial, OWC.
    The 7200 will not lead to problems, be sure that it is compatible, the fastest way to replace if you are using (snow) leopard OS: make a clone of the existing drive to the new one, boot from it when still outside, to test;  replace the internal disk with the new one, et voila...

  • Ram and hdd upgrade questions

    Hay; i'm a apple newbe so forgive me if any of the questions are basic ones.
    I've been trying my hand at things like garageband using a emac that I purchased on ebay but would like to upgrade the ram and the hdd.
    Any answers to any of the below would be extremely helpfull - fyi, about this mac says I have a powermac6.4.
    Ram:
    Google says that my model can take 2gb of ddr333 ram but only 1 gb is supported; is there some kind of issue that arises when one installs more than 1gb?
    Also, should I get low or high dencity ram?
    Hdd:
    Installing ram seems easy enough, but instructions for installing the hdd seem to differ per site that I visit. Would someone be able to link me to some instructions for my model that are known to be correct?
    Idealie i'd like to put a 250gb drive in there, but i'm wondering if this would result in 48lba issues?
    Just out of interest, how much of a speed boost can I expect when going from 5400 rpm to 7200?
    Also, I have noticed that my apple is quite noisy; whilst it doesn't sound like a worringly noisy computer, how much noise of this is due to the harddrive?
    Thanks for any answers.

    Hello and welcome to Apple Discussions. No questions are too basic, as we all have to start somewhere.
    Emac models are best differentiated by the CPU speed.
    You can go to the Menu item  About this Mac will tell you the CPU speed.
    From what you have said it sounds like a later model eMac.
    is there some kind of issue that arises when one installs more than 1gb?
    No, it is just that when these eMacs came out the highest RAM module made at the 333 Mhz speed was 512Mb. Later the manufacturers made 1Ghz modules, thus doubling the capacity from the original specifications. Keep in mind there are two slots for these modules. 1Ghz X 2 = 2 Ghz maximum.
    Also, I have noticed that my apple is quite noisy; whilst it doesn't sound like a worringly noisy computer, how much noise of this is due to the harddrive?
    None of it is due to the hard drive. Hard drive noise is intermittent and barely noticeable. The noise is the roaring of the fan. eMacs are notable for their robust and noisy fan.
    Replacing the hard disk in an eMac requires quite some dissassembly.
    Someone else may post disassembly links as I my old ones don't work anymore, and you may also get more detail about your RAM questions.

  • Displayport sound and harddrive upgrade questions

    1. I'm thinking to buy a Displayport to HDMI cable. One review I read online claimed that Thinkpad T500's Displayport doesn't support sound. It raised my concern. Does my T410 support sound?
    2. If I buy a new hard drive, how to copy the OS (Windows 7) to the new hard drive? I don't have disks. I don't think I have to pay for a new OS, do I?
    Thanks!

    1. Yes, the T410 does support audio over Displayport
    2. You could always make the R&R discs before installing the new harddrive or clone the harddrive.
    Kind Regards
    Jesper
    T61P and 2*T43P

  • WCS and LMS to Cisco Prime Infrastructure 1.3 Upgrade

    Hello,
    Our customer is currently having WCS for 500 devices and LMS 3.2 for 1500 devices. We are planning to upgrade to Cisco Prime Infrastructure 1.3.
    I want to check is the upgrade procedure that we have planned is ok or we have missed something.
    Phase 1: WCS to CPI 1.3 upgrade
    1. Check that WCS is at 7.0.230.0  version
    2. Export WCS database
    3. Install NCS 1.1.1.24 software
    4. Contact cisco to obtain trial license for NCS software (L-WCS-NCS1-M-K9 license).
    5. Migrate WCS license and import it in NCS software
    6. Migrate WCS data to NCS software using ncs migrate command
    7. Patch NCS software
    8. Inline upgrade to CPI 1.3 software
    9. Install proper licenses on CPI 1.3 (WCS and LMS device count)
    My concern in this first phase is should I use NCS large image since our Cisco Prime Infrastructure 1.3 software should manage 2000 devices at the end.
    Or is it better not to perform inline upgrade and insted go with exporting data from NCS and then importing them to CPI 1.3 that is going to be installed separately?
    Phase 2: LMS 3.2 to CPI upgrade
    1. Export LMS 3.2 database
    2. Install LMS 4.2 software
    3. Install license to LMS 4.2
    4. Restore data from LMS 3.2 to LMS 4.2
    5. Direct upgrade from LMS 4.2 to 4.2.2
    6. Export the device list with credentials from LMS 4.2.2  and import it as a Bulk Import in CPI 1.3
    At the end we will have CPI 1.3 and LMS 4.2.2 software running.
    Is it possible to directly upgrade from LMS 4.2 to LMS 4.2.4 and then import data to CPI 1.3 or we need to go with 4.2.2 version?
    Regards,
    Jelena

    Hello Marvin,
    We have restored LMS 3.2 SP 1 database on LMs 4.2 and we have got some error messages during restore. Please see our restore output:
    [kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/res
    resolver.pl           restoreDBTableMig.pl  restoreJRMMig.pl      restorebackup.pl     
    [kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/restorebackup.pl -d /opt/BKP/
    Restore started at : 2013/12/05 14:11:58
    Please see '/var/adm/CSCOpx/log/restorebackup.log' for status.
         USER ID is ..................................... : sysadmin
         OS of the backup archive is..................... : Windows
    INFO:The backup archive is from a different OS. Your current Platform is: Soft Appliance .
    You are attempting to perform a Cross Platform Restore..
    Do you wish to continue (Y/N) [Y] :Y
         Generation to be restored is ................... : 0
         Backup taken from............................... : /opt/BKP/
         Common Services version in the backup data is... : 3.3.1
         Common Services is installed in................. : /opt/CSCOpx
         The temp folder for this restore program........ : /opt/CSCOpx/tempBackupData
         Applications installed on this machine ......... : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][cwportal][ipm][upm][cvw][cwlms]
         Applications in the backup archive ............. : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][opsxml][cwportal][ipm][upm][cvw]
         WARNING: The list of applications installed on this CiscoWorks server does not match the list of
                  applications in the backup archive. If you restore data from this backup archive,it may
                  cause problems in the CiscoWorks applications.
                  Do you want to continue the restore operation?  (y-continue or n-quit, y/n)?Y
         Applications to be restored are................. : [Common Services] [Campus Manager] [Resource Manager Essentials] [Device Fault Manager] [cwportal] [ipm] [upm] [cvw]
         Available disk space in NMSROOT................. : 86451488 Kb
         Required disk space in NMSROOT.................. : 35906524 Kb
         (The temp and NMSROOT are on same device, therefore this required disk space includes temp space)
      Copying the backup files to the temporary location [/opt/CSCOpx/tempBackupData]
      preRestore of [Common Services] has started.
      preRestore of [Common Services] has completed.
      preRestore of [Campus Manager] has started.
      preRestore of [Campus Manager] has completed.
      preRestore of [Resource Manager Essentials] has started.
      preRestore of [Resource Manager Essentials] has completed.
      preRestore of [Device Fault Manager] has started.
      preRestore of [Device Fault Manager] has completed.
      preRestore of [cwportal] has started.
      preRestore of [cwportal] has completed.
      preRestore of [ipm] has started.
      preRestore of [ipm] has completed.
      preRestore of [upm] has started.
      preRestore of [upm] has completed.
      preRestore of [cvw] has started.
      preRestore of [cvw] has completed.
      doRestore of [Common Services] has started.
              Cross Platform Update started.
              Cross Platform Update completed.
              License check started.
                 WARNING: The license details in the server are different from the backup data.
                          After restoring, please check the license available in the server.
                 WARNING: Your current license count is lower than your earlier license count.
                          If you restore the data now, devices that exceed the current licence count
                          will be moved to Suspended state.
              License check completed.
              Restoring certificate.
                 WARNING: Cannot evaluate the hostname, hence the certificate
                          may be from this host or another host.
                          [  Certificate not overwritten  ]
              Restored Certificate.
              Restoring Common Services database.
              Restored Common Services database.
              Restoring CMIC data.
              Restored CMIC data.
              Restoring CMC data.
              Restored CMC data.
              Restoring Security Settings.
              Restored Security Settings.
              Restoring DCR data.
              Restored DCR data.
              Restoring Certificate key store.
              Restored Certificate key store.
      Restoring DCNM CrossLaunch data.
              Restored DCNM CrossLaunch function.
              Restoring JAAS configuration.
              Restored JAAS configuration.
              JRM Job Migration started.
              JRM job Migration done.
      doRestore of [Common Services] has completed.
      doRestore of [Campus Manager] has started.
              Cross Platform Migration for Campus started.
    Cross Platform update Starts for Campus
      doRestore of [Campus Manager] has completed.
      doRestore of [Resource Manager Essentials] has started.
    10% of RME  Restore completed
    30% of RME  Restore completed
    50% of RME  Restore completed
    70% of RME  Restore completed
    100% of RME  Restore completed
      doRestore of [Resource Manager Essentials] has completed.
      doRestore of [Device Fault Manager] has started.
    10% of DFM Restore completed
    30% of DFM Restore completed
    50% of DFM Restore completed
    80% of DFM Restore completed
    Going to modify Eight PM report 
    Modified Sucessfully Eight PM report 
    100% of DFM Restore completed
      doRestore of [Device Fault Manager] has completed.
      doRestore of [cwportal] has started.
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.properties  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.script  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.log  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultUserCommunity.properties  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultCommunity.properties  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
      doRestore of [cwportal] has completed.
      doRestore of [ipm] has started.
            10% of IPM Restore Completed
            30% of IPM Restore Completed
            50% of IPM Restore Completed
            60% of IPM Restore Completed
            70% of IPM Restore Completed
            100% of IPM Restore Completed
      doRestore of [ipm] has completed.
      doRestore of [upm] has started.
    HUM database restore starts
    INFO:STOP= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
    SQL Anywhere Command File Hiding Utility Version 10.0.1.4239
    INFO: Database Shutdown is in Progress..Please wait
    INFO: Stop Engine Args= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
    INFO: After Database Shutdown RC= 2304
    root=C:\PROGRA~2\CSCOpx\databases\upm\upm.db
    DBUTILS: Inside Cross Platform
    INFO: Current Database password does not match the password of Database being restored
    INFO: Using the Password of the Database being restored
    HUM database restore successfully completed.
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate/README.txt
    Directory is reportsStarted changing property .
    linux
    Restored HUM configuration file successfully.
      doRestore of [upm] has completed.
      doRestore of [cvw] has started.
      doRestore of [cvw] has completed.
      postRestore of [Common Services] has started.
      postRestore of [Common Services] has completed.
      postRestore of [Campus Manager] has started.
      postRestore of [Campus Manager] has completed.
      postRestore of [Resource Manager Essentials] has started.
      postRestore of [Resource Manager Essentials] has completed.
      postRestore of [Device Fault Manager] has started.
      postRestore of [Device Fault Manager] has completed.
      postRestore of [cwportal] has started.
      postRestore of [cwportal] has completed.
      postRestore of [ipm] has started.
      postRestore of [ipm] has completed.
      postRestore of [upm] has started.
      postRestore of [upm] has completed.
      postRestore of [cvw] has started.
      postRestore of [cvw] has completed.
    Restored successfully.
    Are this errors going to affect our LMS 4.2 operations?
    Then we have upgraded to LMS 4.2.2 and exported data and credentiales for PI import.
    On PI 1.3 we have installed WCS 500 devices upgrade license and LMS 1500 upgrade license and now we are having 2000 devices lifecycle license. We have successfully restored WCS data in PI and we have imported LMS devices as bulk import. What is strange is that we have this message in prime regarding licensing:
    On LMS 3.2 our customer had saved unlimited number of configuration versioning. After upgrading to LMS 4.2 we can only see last 3 configurations regardless of unlimided number of configurations in previous LMS, so my question is where can we find older configurations in LMS 4.2?
    We are planning to turn unlimited versioning on CPI 1.3 now, so our customer will again have feature that they need. Do you have some experiance regarding disk space when all device configurations are stored forever?
    Thank you for your help.
    Regards,
    Jelena

  • HT204053 i want to change my icloud id on my iPhone, but it won't let me now that i have upgraded.  I no longer have the password and the problem is It is using an old id which the email isn't valid and the security question does not think my birthday is

    I want to change my icloud id on my iPhone, but it won't let me now that i have upgraded.  I no longer have the password and the problem is It is using an old id which the email isn't valid and the security question does not think my birthday is valid.  I cannnot delete the account because "find my iphone" wants the password linked to this old account.  But when i go into the find my iphone app it is using my corect Apple ID.  How do i fix this?

    If you still have access to your old email address, go to https//appleid.apple.com, click Manage my Apple ID and sign in with your iCloud ID.  Tap edit next to the primary email account, tap Edit, change it back to your old email account and verify it.  Then edit the name of the account to change it back to your old email address.  You can now use your current password to turn off Find My iPhone on your device. Then go to Settings>iCloud, tap Delete Account and choose Delete from My iDevice when prompted (your iCloud data will still be in iCloud).  Next, go back to https//appleid.apple.com and change your primary email address and iCloud ID name back to the way it was.  You can now go to Settings>iCloud and sign in with your correct iCloud ID and password.
    If you don't have access to your old email address, you will have to contact Apple to have them reset the password so you can disable Find My iPhone and sign into your iCloud account.  You can either go to https://expresslane.apple.com, select "More Products and Services", then "Apple ID", then  on the next page select "Other Apple ID Topics", then "Lost or forgotten Apple ID password" and click "Continue"; or you can contact Apple Support (http://www.apple.com/support/icloud/contact/).

  • What HD and Controller Card to Buy for Upgrade?

    I've been on OWC looking at the various hard drives and controller cards. My head is swimming. I have a G4 Sawtooth running on OS 9.2. I want to upgrade my hard drive but want to move up to Panther shortly thereafter. Some of the Hitachi products say you need OSX, that I'm afraid if I installed first, would significantly slow down my operating system. Also, I have some software that I would have to use OS 9, as they don't run on OSX, including Photoshop and my Agfa Scanner. Any suggestions on what I should look for?
    By the way, their demo on installation is awesome!

    Flyingcat, I was at this same point about a year ago, and like you I decided to invest in this G4 and maybe get another 2-3 years before making another decision on a new Mac. Here is what I did in the order I did it.
    1. A newer faster HD (with available rebates this was by far the most economical).
    2. A RAM increase to 1.5 GB, but keep in mind OS X will see a full 2 gigs.
    3. An OS upgrade to Panther, but also keeping a bootable version of OS 9.
    4. I upgraded the processor (Sonnet Encore/ST G4 1GHz).
    5. A video card upgrade to Radeon 9000 (this was used and purchased from a close friend).
    6. A SATA HD and controller card.
    Joe
    ps. Is the scanner SCSI and which Photoshop are you using.
    Power Mac G4 Gigabit Ethernet   Mac OS X (10.3.9)  

  • WCS upgrade question

    Hi-
    I have recently installed WCS 4.0.96 on Windows 2003. Foundstone is detecting an Apache/TOmcat vulnerability.
    I saw on Cisco's website that the latest versions are 4.0.97, and 4.1.91.
    Can I upgrade to 4.1.91 by downloading the file on the website? Does it work with the license I have for 4.0.96?
    Thanks!

    Have just upgraded my own wcs, and licensing remained due to the backup made before upgrade/reinstall and restore afterwards.
    Notice that the upgrade is a little complicated.
    1. backup your wcs
    2. uninstall your wcs
    3. install the new version
    4. restore your backup (have patience) this wont work if your server has less than 2 Gb of memory.
    reload the server, and voila your wcs is back online
    /Henrik

  • Design question: Access points and controller Logical/Physical placement

    Background:
    We have an MPLS (layer 3) network 4 offices and a Datacenter:
    We are planning to install about 10 Access Points(3600 series) per office and have a controller(5508 series) in the Datacenter.
    Questions:
    1- Is this design possible, in other words, just one controller centralizing all Access point traffic in one controller in the Datacenter?
    2- We would like to accomplish this in two phases:
        A- install access points without controller handling authentication thru microsoft IAS servers (current configuration with 1200 series)
        B- Deploy wireless Controller in Datacenter and start migrating orphan APs to Controllers one office at a time
    I'll appreciate any advice , comments and suggestions to the the outlined plan/design
    Thanks
    Juan

    1- Is this design possible, in other words, just one controller centralizing all Access point traffic in one controller in the Datacenter?
    Yes... depending on the bandwidth you can either have the APs in local mode which tunnels all traffic back to the WLC or you configure the AP's in FlexConnect and place the traffic locally in each site.
    2- We would like to accomplish this in two phases:
        A- install access points without controller handling authentication thru microsoft IAS servers (current configuration with 1200 series)
        B- Deploy wireless Controller in Datacenter and start migrating orphan APs to Controllers one office at a time
    I don't know what you are trying to accomplish here, but if you are running new cables and replacing all the AP's, you should bring up the WLC in the DC and connect all the AP's but leave the AP as admin down until your ready to cutover.  You can still use the IAS server for radius, just need to create a AAA client on the IAS for the WLC.
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • HT201270 helo, my iiphone is unlock and i upgrade to 5.1 version when the upgrade finish i get this question-An update to the carrier settings for your iPhone is available. Would you like to download it now? is there a resone not to upgrade, will he becom

    helo, my iiphone is unlock and i upgrade to 5.1 version when the upgrade finish i get this question-An update to the carrier settings for your iPhone is available. Would you like to download it now? is there a resone not to upgrade, will he become lock?

    If your phone is factory unlocked, or officially unlocked by your carrier, updating will NOT re-lock the phone.  If it was unlocke by unauthorized methods, any update or restore will re-lock it.

  • Logic pro 7.2.3 and 10.4.8 Upgrade question

    im running logic pro 7.2.3 with mac os 10.4.8 on a g5 2.0 dual core (non-intel ppc) 5gigs of ram. I would like to upgrade both logic and the mac to the latest versions but i am concerned about performance etc. anybody using same specs and successfully upgraded. thank you in advance.

    You'll be able to run Logic 9.02 and OS 10.5.8. Beyond that we are both out of the upgrade path until we get intel macs. It runs pretty well for me. More stable than 8.02, but less stable than 7.2.3. Save often. Time Machine is great though.... no more manual backups. The new features in 9.02 are worth it .

  • Logic express and pro 7 to logic studio 9 upgrade question

    I have logic express 7, logic studio 7, and just upgraded to logicstudio 9, but my serial number is not recognized. All my copies should be registered with apple already, so how should i best remedy this?

    Hi again and thanks for the reply.
    I tried to follow your instructions but isn't working still. I think I did something wrong. Here is what I did:
    1. Went to Midi Setup, double clicked on IAC driver and then checked the "device is online" box. It says its on Bus 1.
    2a. In pro tools, went to peripherals, at the synchronization tab I left MTC reader port: ANY and put MTC Generator Port: IAC Driver, Bus 1
    2b. Then went to the Machine Control tab, enabled MIDI Machine Control and set it to IAC Driver, Bus 1.
    3a. In Logic Express I went to preferences>Midi>Sync and selected listen to MMC Input and took Midi Clock off. I see where it says MTC but there isn't a place to make it the slave.
    I know I'm not doing this right because I hit play on Pro Tools and Logic Express just laughs at me
    Can you help me through this. I'm a novice with Macs and Syncing.
    Thanks again friend.
    Josh
    Mac Pro Mac OS X (10.4.8)
    Mac Pro   Mac OS X (10.4.8)  

  • Panther and Upgrades questions..

    Hey people!
    I'm soon buying a MacBook, I'm just waiting for Leopard to come out..I was wondering, will the upgrade to Leopard would increase the price of the MacBook?
    Besides..Does anyone know, or has apple released any news, if the MacBook will be upgraded with Leopard If so..would that increase the price?
    ..I do not expect you guys to know for sure..But maybe you could tell me how the prices changed in the previous years with OS and hardware upgrades!
    Thank You All!!
    Regards
    Valerio

    Hey ma bad, i meant Leopard on the title!

Maybe you are looking for

  • CS3 issues fixed in CS4?

    Have the following issues in CS3 been fixed in CS4: (Note: a few of these I've found already in the forum, but I am including an all comprehensive list anyway). 1. Self resizing title pane. 2. Still tiff image import incorrectly interpreted as an ima

  • How can I make an applet look to the current directory to read a txt file in?

    I am using a File class passing only the file name as the contructor but forte still looks in "C:\forte_jdk\forte4j\bin\Events.txt" which is not my current directory for the project. If leave it and ftp this applet to my web site I get an IOException

  • Plug problem?  Battery problem?

    This evening the screen on my iBook G4 started oscillating between bright and not quite as bright (unevenly, but sometimes as rapidly as one second). At the same time, the battery icon would switch between showing the power supply connected and disco

  • How to change color of keybored

    I want to be able to change the color of my keybored and the color of the bubbles in messageing and the back round.

  • CS4 - How to list files in order in 'Files view'

    Hi, I have numerous websites but some of them do not list the folders/pages order in the file view. Normally I have the folders at the top followed by the pages as per screen shot 1. I have tried refreshing the folder but no joy and I have gone to th