WCS not showing heatmaps correctly.

I have just installed the latest version of WCS 4.0.66.0 and I have 14 1131 APs running on a 4402 WLC. WCS is only showing heatmap for one AP and the rest are just green showing being up. I have removed all APs and removed the floor plan as well, and started all over from scratch with exactly the same result. Has anyone run into this problem?

There's a bug (CSCse83815) that causes APs to have their antenna types stored incorrectly. They claim to be what you expect when you hover over them, but something in the back end is broken.
You have to go to the AP placement menu, change all the antennas (b/g and a) of affected APs to "other", save, go back, and change them back to what they're supposed to be, save, and then the heatmap should appear correctly.
This happens with almost every AP we install and is really annoying. It shows currently up as "verified" so hopefully it gets eventually fixed.

Similar Messages

Date difference is not showing the correct result for date interval

Hi Expert,
                I've created two formula variable one for PO date and another for GR date
while i am taking the date difference of GR and PO date for single PO date selection
it showing me correct result , but while i am taking the date interval for PO date it not
showing the correct result.
eg: PO date: 01.01.2010   for a particular PO and Gr date is suppose 03.01.2010, 06.01.2010
      it showing the result 2 and 5.
But if i am taking date interval for PO date:
eg: 01.01.2010 - 31.01.2010
PO date: 10.01.2010 and GR date are suppose 15.01.2010, 22.01.2010 and 30.01.2010
it showing me 14, 21 and 29
Thanks and Regards
Lalit Kumar

Hi Expert,
                Through replacement path.
Thanks and Regards
Lalit Kumar

Oam does not show the correct configuration information

Oracle apps,
An issue with the oam.
There are 2 nodes in our system. In 12
One is for db and cm
The other is for forms and apache.
The system is running fine.
But from the OAM, where it does not show the correct configuration info.
From the OAM, all the services are (including db, cm, forms, apache) on one node.
The issue might be caused by the fact that the web tier was cloned from the cm tier as a workaround for some patch errors in web tier.
I even used the EXEC FND_CONC_CLONE.SETUP_CLEAN; to clean the system tables and ran
Autocfg on all tiers. But it didn’t solve this issue.
How can I fix this OAM problem to make it show the correct information?
Thanks,
Lily

Thanks for reply.
Yes, I did commit it.
The hostname information is correct.
On oam, this web node is there but all the service actually running on this node is
showing under the cm node .
<TIER_DB oa_var="s_isDB">NO</TIER_DB>
<TIER_ADMIN oa_var="s_isAdmin">YES</TIER_ADMIN>
<TIER_WEB oa_var="s_isWeb">YES</TIER_WEB>
<TIER_FORMS oa_var="s_isForms">YES</TIER_FORMS>
<TIER_NODE oa_var="s_isConc">YES</TIER_NODE>
<TIER_FORMSDEV oa_var="s_isFormsDev">YES</TIER_FORMSDEV>
<TIER_NODEDEV oa_var="s_isConcDev">YES</TIER_NODEDEV>
<TIER_WEBDEV oa_var="s_isWebDev">YES</TIER_WEBDEV>

Mini Calendar does not show the correct date

Hi there ,
in iCal on the bottom left side of the window is the mini Calendar, when I switch between months in this mini Cal,it does not show the correct month anymore and even the button "Today" can not revert the day back ( for example we are now in September, when I open iCal it shows it correctly but after going to next or previous months using the triangles on this mini Cal, the problem comes up ! )

Maybe it wasn't receiving the correct info from your carrier. You're supposed to turn your phone off once in a while so the carrier can update stuff. I had originally heard that you should do it once a day but I never did that.

The percentage completed UI is not showing the correct data

Hi All,
I have received complaints from one of my larger customers that a very long form we have created is not showing the correct % completed at the bottom. They get to the penultimate page (the last page only have three text boxes on) and it state that only 41% of the form has been completed.
It looks to me like the UI is not updating as the questions are being completed. Rather it waits until you move to the next page.
This is what makes our form look rubbish - you are being told that you have only completed 41% of the form only to move on to the next page and bam, you only have three more boxes to complete.
Can somebody help me out here.
Thanks,
Bill

Hi Bill;
I can take a look at your form but you are right that only the pages are accounted for in the percentage and not the form fields so it can be far off from reality. If there is skip logic in a form that can make it vary more. It is likely that it is working "correctly" (considering how we calculate) in your form but if you send me the link to your form at [email protected] I can see if it is not.
Thanks,
Josh

Installer is not showing the correct Nodes in RAC

Hi Experts,
We are in the process of upgrade oracle database from 9.2.0.3 to 9.2.0.8 in RAC. While installing the 9.2.0.8 patch set it is not showing the correct database nodes, instead of it showing production database nodes, but we are doing doing it in test machine.
Test Machine hostname:
db1
db2
Prod machine hostname
prod1
prod2
it showing the prod1 and prod2 only.
please suggest us to solve this
Note:
We copy the oracle_home from prod to test for test database cloning.
Thanks
R.Sundaravel

Then it is highly likely your RAC cluster is not correctly configured.
Open an SR at metalink as the Cluster Verify tool does not exist for your old version.

Labels Not Showing Up Correctly in Workflow Manager Web Page

I have installed the Workflow Server 2.6.3 on Red Hat 7.2 against the Oracle 10g database. When I go to the Workflow Manager web page and login, all the labels appear between brackets "[]" and have incorrect names such as the following:
WF_WORKFLOW_TITLE
WFA_WTITLE
OPEN_NOTIFICATIONS
WFA_FINDTITLE
WFRTG_FIND_TITLE
etc......
I ran the Configuration Assistant again and this didn't solve the problem and I've also verified that the mappings in the server configuration file are correct for OA_JAVA, OA_DOC, OA_MEDIA. Looked through workflow installation log and no errors appear. I installed the web server (Oracle Apache Standalone downloaded from OTN in a separate Oracle Home). Any ideas how to fix these incorrect labels or why they're not showing up correctly??
Thanks in advance,
Rich

Hi,
I've not seen the problem myself, but it seems that the language has not created the correct lookups in the WF_RESOURCES table.
If you look for a name of (for example) 'OPEN_NOTIFICATIONS', there should be an entry for the language you are using (US) which translates the prompt for you. If it's not there then you will probably need to add a language through the installer - I don't think there is a SQL file that you can just run to do it. Alternatively, install it in a new environment and then just extract the resources you need from that system and insert them into this one.
HTH,
Matt
WorkflowFAQ.com - the ONLY independent resource for Oracle Workflow development
Alpha review chapters from my book "Developing With Oracle Workflow" are available via my website http://www.workflowfaq.com
Have you read the blog at http://thoughts.workflowfaq.com ?
WorkflowFAQ support forum: http://forum.workflowfaq.com

Lightroom 4.1 can not show text correctly

lightroom 4.1 can not show text correctly when publish in PDF and blurb format
the text can be show correctly in JPEG format
but lightroom 4.0 can show correctly with the same book.
i cant publish my book on blurb now

I don't think LR4 adjustments can be directly sent to CS4, because CS4 cannot interpret LR4's new processing engine.
I think you have to use Edit In... and create a TIF or PSD and send those to CS4

My storage is not showing the correct space

Hi,
Why my storage is not showing the correct amount of space? I have MBA mid 2013 with 121gb. However my storage show a different value than its suppose to be especially on the apps. I google the problem, mostly its because of the time machine but I never use the time machine. and some of my friend tells its probably a junk. is the third party apps like apps cleaner and clean my mac is helpful? I attached the screen capture of my storage. As you can see the value of apps is 162gb in fact my flash is only 121gb. its doesn't make any sense. Please help.

Do not use third party apps such as CleanMyMac on your Mac. They have no effect what so ever on storage space. Your Mac runs maintenance in the background for you > Mac OS X: About background maintenance tasks
Reindex Spotlight then check the storage > Spotlight: How to re-index folders or volumes

WCS not showing AP type or antenna choices

When I look at the config for some of my AP's they are showing under the Inventory Information AP Type Unknown. Also, when I go the radio interface for b/g and try to change the external antenna from Other to the 5959 antenna, there is no antenna's listed at all.
I looked at other AP's that are working and they show AP Type as LWAPP and have all the antenna choices listed as well.
The WLC version is 4.2.112 and the WCS version is 4.2.81.
I found this problem after changing some of the AP's to manually set the channel assignment. I then went to look at the heat map for all the AP's in one building and nothing shows up, just the AP's with no color heat map. I did reset the AP's with no change.
Thanx, Seth

Was not seeing any error messages. I was just not able to get the heat map to generate. Also, I could not choose the correct antenna that was connected to the AP because the AP type was showing up wrong.

Images edited in Photoshop not showing up correctly in Lightroom after saving

Hi,
I recvently got Adobe cloud and upgraded from Lightroom 3 to 4. Since the upgrade I have been having issues with Lightroom not correctly displaying images edited in Photoshop. Instead of the photoshop image it creates a new jpeg and displays that in the library. the PSD does not get loaded into the library.
I am taking a jpeg from my library and shoosing the edit in Photoshop function. I am selecting edit a copy, but have tried it with original and with edit a copy with lightroom adjustments as well with the same results.
In Photoshop I am duplicating the base layer, upscaling the image, running some filters, adding dsome adjustment layers.
I save the image in Photoshop format back to the original folder where the initial jpeg was in the Lightroom library. I save it with maximize compatibility on.
When I go back to Lightroom, the catalog displays two files, the initial jpeg and an identical copy to it, NOT the new photoshop file with alterations. If I go to the folder the images are housed in in Finder using the show in Finder command both images link to the same original jpeg. The photoshop edited file is there in the folder but does not show up in Lightroom unless I drag and drop it.
I have turned off all filters and made sure the sort is sorting by name. The image does not automatically show up in Lightroom after editing. Any suggestions?
Thanks for any help!
PS. I did search the topic and there are threads from 2007 and lightroom 2 but their solution was to start from scratch essentially and I have a carefully tagged, starred, and labeled catalog of 30,000+ images and really don't want to do that

Images that are edited in Photoshop will be displayed automatically in Lr only when the image-file saved in Photoshop is the same as the one opened from Lr.
You say you open a JPG from Lr, then edit it in PS by - among other things - adding some layers. Layers are not supported in the JPG-format so you have to either save it as a psd or as a jpg-copy.
In either case this is not the same image file as the one opened in Lr, so it will have to be imported into Lr to show up. If you would flatten your image after editing in PS and then do a <save> to your JPG - not a <save as> - it will show up in Lr.
PS: the only exception is when you open a Raw image from Lr in PS and you save it in PS in the file format specified in Lr for external editing. The saved file will automatically show in LR.
Message was edited by: web-weaver; PS added

Print preview not showing values correctly. (single words are omitted)

Hi,
When viewing print preview of ME23n , it does not shows the values correctly.
It omitting the single words.
If its having 2 or more words, it displaying correctly
For example;
This is the vendor & its address. (check attached image img1.jpg)
ZERANDIB BUSINESS APPLIANCES
Number-122/A
PO BOX 41,112,REID AVENUE
COLOMBO-04
When displaying the print preview, it shows only some parts of the above address
Shows only; (check attached image img2.jpg)
ZERANDIB BUSINESS APPLIANCES
PO BOX 41,112,REID AVENUE
These values are getting from a table called LFA1. I have checked that table & in that table all the values exists correctly.
I have noted issue is with, having only a single word. (If address or name having only a single word, that is without spaces, it will not going to show in the print preview) -
In the above example, it is not showing Number-122/A and COLOMBO-04 (Its a single word. No spaces there)
If its like --> Number - 122/A & COLOMBO - 04 , then it will display in the print preview correctly (where there are spaces after - mark)
check img3.jpg
If its having more than one word, then it will display correctly in the print preview. As below;
ZERANDIB BUSINESS APPLIANCES
Number - 122/A
PO BOX 41,112,REID AVENUE
COLOMBO - 04
Any ideas how to resolve this issue?
Is there any thing to do with printer settings & configurations / netweaver admin point of view?
Best Regards.
Zerandib

Hi Zerandib,
By the way , since its a standard program, i think that code is out of our scope.
Me23N is a standard tcode but cusomters create Z-Program for printing by making a copy of standard.
You may please check upon the same.
Is it possible to check the results on a system where patch has not been applied ?
Regards,
Deepak Kori

AP mesh info in WCS not show bridge links.

Hi guys,
I would like to know if any of you following problem has occurred. I have implemented 3 wireless mesh with 1262 AP WLC 5508 v 7.0.116.0 and WCS 7.0.172.0 base lic, all has been running perfect, the problem arises when I want to see on the map graphically bridge links, I have enabled AP Messh info but it not shows the bridge links, in hierarchical Mesh Parent-Child View only shows the RAP. To load the maps we used Campus> Outdoor area> AP.
I will appreciate any comments.
Greetings.

Are you loading 4.0? With WCS 4.x you need to generate a license with the PAK you should have received from Cisco. If you did not receive a PAK, read the following excerpt from the following url:
Existing Cisco WCS customers that have not received their PAK certificate from Cisco should contact their Cisco sales representative or send an e-mail to the [email protected] alias to notify Cisco that they need their PAK certificate. Cisco will attempt to respond to requests to this alias within 48 hours Monday-Friday 9AM-5PM Pacific Standard Time.
http://www.cisco.com/en/US/products/ps6305/products_data_sheet0900aecd804b4646.html
I hope this helps.
-Eric

The colors are not showing up correctly on my site like they do in photoshop and explorer.

Why don't the colors show up correctly in Firefox? They are exactly the same color yet firefox shows them as slightly different. I checked them in Photoshop. Same hexadecimal, same RGB. It looks correct in Internet Explorer but does not in firefox. The color is: hexadecimal: #0FCFF3, RGB: 15,207,243.

This can be caused by a problem with the color profile for your display monitor or color profiles embedded in images.<br />
Try to disable color management to test if it is caused by a problem with color management.<br />
You can set the gfx.color_management.mode pref to 0 on the about:config page to disable Color Management.<br />
You need to close and restart Firefox to make the change effective.
See:
* http://kb.mozillazine.org/gfx.color_management.mode
*http://kb.mozillazine.org/about:config

International characters not showing up correctly in Podcast Title-Is UTF-8

In the 'Podcast Information' window that pops up, the Episode title is not getting rendered correctly but the details show up fine. Both have chinese characters.
Any pointers for resolving this would be appreciated.

If sometimes it works, and sometimes it doesn't, then there must be a difference in the way you are doing it. And you can work out what's happening from analyzing what you're doing when it works compared with what you're doing when it doesn't work.
For example, if you type the description into the blogging software, you might just be typing the ' key. While some writing software (word for example) will automatically turn on smart quotes which your blogging software will be escaping into HTML code. The character ' doesn't need escaping, but smart quotes do.
Hope this helps,
Greg

WCS not showing heatmaps correctly.

Similar Messages

Maybe you are looking for