WCS used to configure SSID broadcast for WLAN issue
Hi,
When I try to disable the broadcast parameter for an SSID on a WLC using WCS (4.0.96.0), I am running in to some issues.
I uncheck the 'Broadcast SSID' check box for a particular SSID and then submit the change. But, after I submit, the check box is still checked. If I verify the setting on the native WLC web interface, the Broadcast SSID parameter is still enabled.
I can change other parameters OK, so I don't have an SNMP issue.
If you perform this operation from the WLC web interface or the command line, you have to disable the WLAN first, before the SSID broadcast can be switched off.
I suspect that WCS doesn't have the intelligence to disable and re-enable the WLAN to perform this operation. But, it very frustrating that it doesn't even generate a warning or failure message to say that the operation has failed.
Anyone seen this or can perhaps tell me if I am mis-operating WCS in some way ?
Thanks.
The WLANs tab allows you to create, configure, and delete WLANs on your controller.
You can access the following pages from the WLANs menu bar selection:
WLANs
WLANs > New
WLANs > Edit
WLANs > Mobility Anchors
AP Groups VLAN
Similar Messages
-
Disable SSID broadcast solve the E4200 continuous flashing problem
I was quite excited about E4200 I got yesterday. Everything works perfect except front LED light start blinking a few hours later. Don't know why it happens in a sudden and non-stop.
After several tries, I found that disabling SSID broadcast for both 2.4 and 5GHz stops the blinking.
Of course, before doing that, I upgraded firmware to 1.0.02, reset to factory defaults and finally set up E4200 manually rather than using Cisco Connect.
Now the LED light is continuously lit.
I hope this hint could help you to solve the poblem as well.I wonder if the 'flasjhing logo' problem (which indicates WPS connection is in process) could be due to using Cisco Connect initially.
I am thinking of doing a '30-30-30' rest, using the web browser for all the configuration.(I have been doing this ever since ditching Cisco Connect early on). -
WRT54G-V3 Disabling SSID Broadcast/Laptop connectivity
I set up this wrt54g v3 yesterday
everything went well
but when I attempted to disable the ssid broadcast for the network, I completely loose all connectivity on the wireless laptop
here is what I have
wpa-psk/tkip
wireless mac filtering
and my challenge is this "disable broacast" thing because once I do I loose all connectivity on the laptop.
As of 9:00am EST I have the broadcasting on but the network is secured but I really would like to know what element I'm missing here.
Also when I did this able the broadcast the laptop wireless card was flickering but I never quite stayed on for me to use it.
My goal (if I had one) would be do disable the broadcast and still have my laptop have connectivity to the AP.
Thanks in advance and God bless.Hmmmm... probably a laptop glitch.... can't connect to the network coz it can't see it.
Try upgrading the routers firmware while your at it. It's the most you could do coz everything actually checks out fine.
Message Edited by sharkbyte on 03-06-200701:41 PM -
Use module configuration location
Hi,
i tried in the configuration of a sql loader mapping the "Use module configuration location" option for the location of the control file. The problem is that i can select that value but it's not possibile to check. I can only select a location from the combo box.
Is there a particular configuration for this choice?
Thanks,
LucaYes, I can view and modify all the locations. The "problem" is that with OWB 11 I don't know how to set a default location for a module (I think that every mapping can use the default value). In OWB 10 I must not define a location for control files (there was a default value).
Any ideas?
Thanks,
Luca -
Regarding configuration of "Parameters for determining the basic dates"
Hi All,
Can anyone give inputs in which scenario we need to use the configuration "Parameters for determining the basic dates".
1)Do we have any restrictions for usage of above IMG configuration, 2) any pre-requisites to use the configuration of "Parameters for determining the basic dates" and 3)does configuration of this task is having any integration with any other modules, if yes what is the point of integration with other modules.
Thanks in advance.Dear Aditya,
Parameters for determining the basic dates in production order are used to calculate the Basic Start date & End date of Production order. It Determines if and how the basic dates or the dependent requirements dates are adjusted during lead time scheduling. You can customize this in OPU3 for planned order & OPU5 for Production Order.
There are the following possibilities:
1.The basic dates are adjusted and the dependent requirements are scheduled for the start dates of the relevant operations.
2.The basic dates are not adjusted and the dependent requirements are scheduled for the start dates of the relevant operations.
3.The basic dates are adjusted and the dependent requirements are scheduled for the order basic start date.
4.The basic dates are not adjusted and the dependent requirements are scheduled for the order basic start date.
1)Do we have any restrictions for usage of above IMG configuration
For scheduling this has to be. If you want that start date should be calculated based on Inhouse production time & not on routing select opetion 2 or 4
2) any pre-requisites to use the configuration of "Parameters for determining the basic dates"
Not as such
3)does configuration of this task is having any integration with any other modules
Not directly but with MM to determine dependent requirement Proposal.
Regards
ABhijit Gautam. -
Setup of approval for Miscellaneous issue transaction in Inventory
Dear Experts,
We have a requirement from client to setup approval for Miscellaneous issue/
receipt transaction in Inventory.
Is it possible to fulfill the above requirement using Approval Management Engine (AME)?.
If it is possible, Kindly explain me in detail about the setup steps needed for the
configuration of Miscellaneous issue/receipt transaction in Inventory.
Kindly respond at the earliest as the requirement is needed urgently for our client.
Thanks in advance !
Best Regards,
Naveen.D
Dear Lavanya,
The material should be first reeived to Inventort then transferred to projects
Ex 100 Quantity is Received @ 10 Each - Inventory Material value will be 1000 Unit Price 10
Now 10 Quantity is Issued(Samples) @ 0 each - Inventory material Value will be 1000 Unit Price 11.11
Now Transfer the remaining quantity to Projects i,e 90 quantity, & inventory material value will be 1000, unit price will be 11.11 (Use Project related Misc Transaction for Project Issues)
Even though material is issued with 0 unit price A/c entries will be generated
Dr. Given A/c
Cr. Inventory material value A/c
Here first the material is directly received into Inventory (Not related to projects organization) Miscellaneous Issue (For samples) is done with 0 unit cost after that The material is transferred to projects (Project Issues)
For Miscellaneous Issue (Samples Issue) a Personalization is need to done such that the Unit price will be freeze to 0.
Regards
Shaan -
Product ID for second issue of multi viewer app
hi,
I've in this forum already found very usefull info about publishing the second issue of a free multi viewer app but still can't figure out if we have to use the same Product ID for each issue, or do we need to create a different Product ID for each issue ?
I've put two examples below, suppose one of them has to right. Or not ??
Is this the way to handle multiple issues (option 1):
product ID issue 1 = Product ID issue 2 = com.magnusmedia.magname
Or is this the right way (option 2):
product ID issue 1 = com.magnusmedia.magname.01
product ID issue 2 = com.magnusmedia.magname.02
thanx in adavance
Herman
Allright, was in a hurry and tested it out myself.
Option 2 is working for me, hope it's right to handle it that way.
With option 1 the app crashes (dark gray screen, no folio opens, library- en scrolling buttons are available but)Short answer: Yes, use a different Product ID for each folio (or for each set of folio renditions).
Longer answer: It's confusing that there are three different types of Apple Product IDs:
(1) the app Product ID, which you can ignore
(2) subscription duration Product IDs for a paid app or a single Product ID for a free subscription app
(3) a Product ID for each retail folio
When you're setting up a free subscription app, you don't need to use iTunes to create a Product ID for individual folios, because your folios are free. You just need to set up a free subscription Product ID in iTunes Connect and specify that Product ID in the DPS App Builder. On the Adobe side, you use a different Product ID for different folios you publish, such as com.publisher.publication.2012October and com.publisher.publication.2012November. If you're creating renditions, you use the same Product ID for the different renditions and different Product IDs for different sets of renditions. -
Costing for Miscellaneous issue transaction for project
We have a different requirement from the business
ours is R&D and we are using Oracle projects to track our projects costing and billing
we procure some material from outside supplier and it will get costed to the project but when any engineer want to use the material they want to reduce the material from the inventory by they dont want the cost to get reduced from the project
usually engineers take the material by doing miscellaneous issue for some testing and they never get in to the project again it will be treated as samples
currently when i do the miscellaneous issue it reduces the inventory from project and also the cost will get reduced.
Can someone help me out since it is very critical for us to acheive this,
Regards
LavanyaD
Dear Lavanya,
The material should be first reeived to Inventort then transferred to projects
Ex 100 Quantity is Received @ 10 Each - Inventory Material value will be 1000 Unit Price 10
Now 10 Quantity is Issued(Samples) @ 0 each - Inventory material Value will be 1000 Unit Price 11.11
Now Transfer the remaining quantity to Projects i,e 90 quantity, & inventory material value will be 1000, unit price will be 11.11 (Use Project related Misc Transaction for Project Issues)
Even though material is issued with 0 unit price A/c entries will be generated
Dr. Given A/c
Cr. Inventory material value A/c
Here first the material is directly received into Inventory (Not related to projects organization) Miscellaneous Issue (For samples) is done with 0 unit cost after that The material is transferred to projects (Project Issues)
For Miscellaneous Issue (Samples Issue) a Personalization is need to done such that the Unit price will be freeze to 0.
Regards
Shaan -
Limit SSID Broadcasts with WCS or WLC
Is it possible to limit which SSID's particular AP's broadcast? I've tried using AP Groups, but that only segments the VLAN broadcast domain. The AP still broadcasts all SSID's. I have 2 APs in a jury waiting room - I only want to broadcast their SSID, not the all the others (confusing for them). Does anyone know how to do this? We're using a 4400 series WLC in this building and version 5.0.56 of WCS.
Hi Bill,
You will want to look into this.The feature you are looking for is called WLAN Override :)
Enabling WLAN Override
By default, access points transmit all defined WLANs on the controller. However, you can use the WLAN Override option to select which WLANs are transmitted and which ones are not on a per access point basis. For example, you can use WLAN override to control where in the network the guest WLAN is transmitted or you can use it to disable a specific WLAN in a certain area of the network.
From this doc;
http://www.cisco.com/en/US/products/ps6366/products_configuration_guide_chapter09186a008076cbfd.html#wp1114777
Once you create a new WLAN, the WLAN > Edit page for the new WLAN appears. In this page you can define various parameters specific to this WLAN including General Policies, RADIUS Servers, Security Policies, and 802.1x Parameters.
**Check Admin Status under General Policies to enable the WLAN. If you want the AP to broadcast the SSID in its beacon frames, check Broadcast SSID.
Note: You can configure up to sixteen WLANs on the controller. The Cisco WLAN Solution can control up to sixteen WLANs for Lightweight APs. Each WLAN has a separate WLAN ID (1 through 16), a separate WLAN SSID (WLAN name), and can be assigned unique security policies. Lightweight APs broadcast all active Cisco WLAN Solution WLAN SSIDs and enforce the policies that you define for each WLAN.
From this good doc;
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a0080665d18.shtml#c3
The most popular way to mitigate the problem of having to access each AP individually (when using WLAN Override) is to use WCS Templates for common requirement AP's. This way the WLAN Override function can be applied at the Template level and then pushed out to the various groups.
http://www.cisco.com/en/US/docs/wireless/wcs/4.0/configuration/guide/wcstemp.html#wp1072198
Hope this helps!
Rob -
SSID broadcasts a secure network but no security configured
Hi,
I have a wireless network using Cisco 1231G AP's in autonomous mode. Each AP is configured with a guest VLAN and this points to a BBSM server.
The issue I'm having is the SSID for guest access is configured as open with no security parameters set. However, my client (CB21AG) sees the network being broadcast sometimes as open and other times as secure.
AP configuration:
ssid bbsm
vlan 295
authentication open
guest-mode
IOS Version: 12.2(13)JA4
Output captured from AP scan logs:
2008-10-01 12:43:36 ,bbsm,00:12:DA:A7:F5:30,-50,Secure,G,1
2008-10-01 12:43:36 ,bbsm,00:12:DA:A7:F3:B0,-71,Open,G,11
2008-10-01 12:43:36 ,bbsm,00:12:DA:AE:A7:B0,-78,Secure,G,2
2008-10-01 12:43:36 ,bbsm,00:12:DA:AE:7B:90,-91,Open,G,10
2008-10-01 12:43:36 ,bbsm,00:12:DA:B6:58:60,-91,Secure,G,13
2008-10-01 12:43:36 ,bbsm,00:12:DA:B6:66:F0,-92,Secure,G,13
2008-10-01 12:43:36 ,BTOpenzone,00:02:8A:A3:04:A4,-71,Open,B,6
2008-10-01 12:43:36 ,hpsetup,02:13:02:00:02:15,-88,Open,G,11
2008-10-01 12:43:36 ,Voyager test,00:16:E3:32:58:A9,-43,Open,G,5
2008-10-01 12:43:56 ,bbsm,00:12:DA:A7:F5:30,-52,Secure,G,1
2008-10-01 12:43:56 ,bbsm,00:12:DA:A7:F3:B0,-69,Secure,G,11
2008-10-01 12:43:56 ,bbsm,00:12:DA:AE:A7:B0,-77,Secure,G,2
2008-10-01 12:43:56 ,bbsm,00:12:DA:AE:7B:90,-89,Secure,G,10
2008-10-01 12:43:56 ,bbsm,00:12:DA:B6:58:60,-91,Secure,G,13
2008-10-01 12:43:56 ,bbsm,00:12:DA:B6:66:F0,-92,Secure,G,13
2008-10-01 12:43:56 ,bbsm,00:12:DA:AE:9B:00,-93,Secure,G,5
2008-10-01 13:20:36 ,bbsm,00:12:DA:A7:F5:30,-52,Open,G,1
2008-10-01 13:20:36 ,bbsm,00:12:DA:A7:F3:B0,-67,Open,G,11
2008-10-01 13:20:36 ,bbsm,00:12:DA:B6:58:60,-91,Open,G,13
2008-10-01 13:20:36 ,bbsm,00:12:DA:AE:A7:B0,-75,Open,G,2
2008-10-01 13:20:36 ,bbsm,00:12:DA:AE:7B:90,-94,Open,G,10
2008-10-01 13:20:36 ,BTOpenzone,00:02:8A:A3:04:A4,-69,Open,B,6
2008-10-01 13:20:36 ,Voyager test,00:16:E3:32:58:A9,-40,Open,G,5
Any ideas or help on why I sometimes see the ssid broadcast as secure?
Thanks
SimonIt is one of mine. Yes. It connects to it no problem, just doesn't connect to the actual internet. Network diagnostics has all green lights until the ISP and/or Internet point. If I walk through diagnostics, it will get to the point where it says that the network requires a WEP password. I don't know why it does that because my network is not password-protected (husband claims it doesn't work well with his VPN system to get into work network). If I leave it blank, the connection will work. Eventually, after the computer is put to sleep, I will have the same problem upon waking up. I just tried renaming the network and removing all preferred networks and rebooting. Let's see how that works.
-
Disabling SSID broadcast sets NAT to strict for XBOX 360, even if wired to WRT160N
I don't know if this is true with all routers, but with my WRT160N, I found that disabling SSID broadcast causes NAT to go into STRICT mode, and there's no way to get back to OPEN (port forwarding, DMZ, etc, unless you enable it.) Unfortunately I had just upgraded my firmware, which sent me and the Linksys tech down the wrong path. The bummer is that XBOX is wired to my router, so not sure why this would've been affected. Hopefully this helps, since I've seen several **bleep**!?! threads around this. I just happened to stumble across this after my NAT opened up when I reset my router to factory settings. Stepped through the changes I had made from default, and wallah, it was the the stupid disabled SSID broadcasting.
Message Edited by daveyhatton on 01-26-2010 01:42 PMYou are wasting more "cycles" if you disable the broadcast because your wireless devices have to actively search your network instead of simply listening to the list of broadcast SSIDs and connect to the correct one.
If "normal folk" want to crack your network they will quickly give up if they do it manually (assuming you have a strong WPA2 passphrase set on your router). Those few attempts won't cause you problems. Your router and wireless network will far more affected by other wireless networks and interference then some failing connection attempts.
Of course, I assume here that you have changed the SSID from "linksys" to something unique. If you still use "linksys" you will probably see quite a few failing connection attempts, not intentionally but because some people had their computer configured to connect to "linksys" before and still use it or did not remove it from their list of preferred networks. And if it is still "linksys" hiding the SSID won't make a change here, too...
They provide the option because that's what people want to see and buy. It does not matter whether it is really useful or not. Marketing says you can "hide" your router and people believe it. If you take the first computer at hand and look for networks the normal way it won't list it. Great, people believe it's "invisible". Sells good. Just like people need firewalls to "stealth" their computers in the internet which neither hides their computer not makes it any more secure...
As long as marketing does not mention that a simple network sniffer will immediately show the existence of the router and very soon will also reveal the SSID... It wouldn't sell so good anymore...
Of course, the setting should not affect port forwarding and your "NAT" level. Could be a firmware bug in the WRT160N.
Message Edited by gv on 01-27-2010 07:40 PM -
I need to configure my IPad for the co WLAN , The advise i got is to send the certification through exteral mail to the IPad and install them but this option cannot go in my case as the network availbe now is co WIFi . I tried to share the certification from my microsfot laptop through itunes but i cannot install them in IPad as there is no application can open them . Can any one advise me what is the applicant can be used to run this certifications ( Cer files ) in IPad .
If you are running OS X 10.5.8 as your profile says, that is the problem as you need to be on OS X 10.6.8 (Snow Leopard, or above). If you do upgrade, after installation do a software update from the Apple menu so that the OS and iTunes gets updated to the latest version for SLeopard. Here's a snippet from the iPad mini tech specs:
Apple ID (required for some features)
Internet access6
Syncing with iTunes on a Mac or PC requires:
Mac: OS X v10.6.8 or later
You can upgrade to Snow Leopard ($20 U.S.) if your computer is compatible and you have enough RAM. Snow Leopard tech specs:
http://support.apple.com/kb/SP575
Snow Leopard can be order from Apple's Online Store in your country:
http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard -
I manage 60 ipads for a school using Apple Configurator. Need to update my devices to iOS7 and Apple Configurator to 1.4.3...Is it best to use Mountain Lion or Mavericks, as I also need to update from Lion 10.7 for the new Apple Configurator and iOS7 to work properly.
I always run a Time Machine backup before updating anything and recommend you run a backup as well. Paid apps should migrate over without any problem. If you have problems with VPP codes not transfering over properly, you can talk to your Apple SE or contact VPP for Education support and they can help you. While I haven't experienced any problems with updating, its never a guarantee that others will have the same experience.
Good luck!
~Joe -
Using different configured views for different user group in crm2007
Hello SAP Expert,
Want to clarify if the BADI (Configuration Access Determination BADI ; BSP_DLC_ACCESS_ENHANCEMENT) is used as design time or Run time. By looking the help of this BADI it says "This Business Add-In (BAdI) is used in the UI Configuration Tool (CRM-FRW-CON) component." Looks like this is at configuration time not at run time.
The actual requirement is that for a set of users which work on a particular department, we want to have some extra information on 2 views and rest of the views they would be using same as entire organization. We are inclined towards using config role rather than zviews. If we were to use zviews then it would not be a difficult one.
We were thinking of a mechanism to show the configured view based on user's Business Role at runtime. e.g. we have 2 roles A and B. Role A user have only 2 views specific to them and all other views they use same as Role B. We do not want to use ZView rather use Role Config Key to distinguish the views. What I was thinking that we should be able to create these 2 views with Config Role A and all views (including these 2) with Config Role B. On Business Role A and Business Role B both, We will assign Config Role "B". but at runtime system should determine if the Business Role is A and Component is CMP1 then use the view V1 with Config Role A not the default view with config role B. (we can maintain that information in a Z table). This is not based on runtime profile but to use configured view at runtime.
Any thoughts/ help really appreciated.
Best regards,Hi Amithab,
you can use badi CRM_BP_UIU_VIEW_CONFIG of enhancement spot CRM_UIU_BP_ENHANCEMENT for your requirements. Please read the badi documentation because you need also a implementation of badi CRM_BP_UIU_CONFIG_CALLBACK (same spot). SAP considers badi CRM_BP_UIU_VIEW_CONFIG only for use at dynamically loading different configuartions of view details for business partners or contact persons at runtime. But you can use your badi implementation also for other views. You have to redefine method DO_CONFIG_DETERMINATION in your views. And call your badi from there. For this copy&paste the logic of DO_CONFIG_DETERMINATION of bp details to the views you have to load dynamically at runtime.
We have used this approach for access controll and granting special access to views dependent on different employee functions.
Best regards
Michael -
Configuring Cisco Router for use with Syslog Server
Configuring Cisco Router for use with Syslog Server:
Does anyone know of a good doc for this?
-AshleyStart with that one: http://security-planet.de/wp-content/uploads/2008/12/logging-ios.pdf
And if you need more informations, just ask what you want to achieve.
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni
Maybe you are looking for
-
Cheque Printing issue incase of Vendor advance payments
Hi all, We are doing vendor payments using F-58 and printing cheque from there itself, and in case of advance payments we are using F-48 for payments and to print cheque we are using FBZ5. When we take printout from FBZ5 for advance paymen
-
Hi, Presetnly I am working with FBL1N Transaction. Vendor Line Item Display. I would like some one to elaborate on that the usage of this transaction FBL1N. Actually when I am passing the Vendor A/c it should be posted to WBS element, but it is get
-
Hello to everyone! I am having a problem using footnotes in InDesign. I place a word file (62 pages) in a text box, which containes footnotes. The problem is that in InDesign the footnotes start from number 2 (it should start from number 1 as in the
-
Error blocking deployment?
I am deploying a JDev 10g preview UIX/TopLink application to a standalone OC4J 9.0.4. I have deployed this application to this server several times before. We had changed the database schema and the copy of the application on the server had thrown an
-
Hi people, I have a number of dynamically created MovieClips that are used to draw stuff into them. Because the content may be erased, the MCs have to clear() themselves sometimes. Now I want to have a kind of grid drawn also in those MCs, some small