WD 320GB in my macbook does not show reliably in Disk Utility

Hi
I have bought a Western Digital 320GB Scorpio for my C2D MacBook but it does not seem to work as an internal disk in the macbook, when unformatted it does show up (but not every time) but when formated as MacOS Journaled it never shows up in Disk Utility, I've tried using the leopard installer as well as booting from my original 80GB disk plugged into an enclosure. Once the disk is formatted disk utility is very slow at showing the other disks compared to the mere seconds it usually takes. I've tested this disk in a PC and it seemed to work fine formated as NTFS, successfully copied and read some files from it.
What could be wrong with this disk or my macbook?

After unsuccessfully trying two Western Digital Scorpio 2.5" SATA drives (320GB SATA II and 250GB SATA I) in the MacBoook, I have resorted to buying a Seagate Momentus 250GB drive which works perfectly.
I suspect an incompatibility between the Merom-based Core2Duo MacBooks and the WD Scorpio drives. So if you have an early Macbook, I'd steer clear of WD drives.

Similar Messages

External Hard drive does not show up on Disk Utility

I have a External Hard Drive that I used to use on a PC.
Recently, I just bought a new Macbook Pro 13'' and want to transfer my documents from the old PC to the Macbook.
My External HD requires a password that you need to type in in order to access the files.
This password thing runs smoothly on my PC, which I can type in my password and get the files. But when I plugged it into the Mac, it didn't recognize it. It only shows the files .exe... and other that can be run by Windows.
So I formatted the HD (I already back up the data), and put it back to the Macbook, I still cannot open it. The system does recognize the connection but when I opened the Disk Utility while still connecting to the HD, the HD does not show on the left column of the Disk Utility.
Then I'm stuck.
Is there anyone here can tell me what I can/should do?
A girl who spends hours on the internet and still cannot figure out why this sh*t is happening to her.

A lot of external drives use firmware passwords as a protection scheme. To use them on a mac, you need to unlock the drive on a PC (I've done it in a virutal machine before). Once unlocked, you can format the drive for use on a mac. The firmware won't run properly on a mac so your ability to lock the drive from the mac will be gone. You can still lock it from a PC (I think, never tried to firmware lock a drive with a mac partition on it).

I am trying to format a new external hard drive. It is attached via a USB 2.0 docking station. It does not show up in Disk Utility or Terminal, but does show up in System Profiler. How can I get my MacBook Pro to recognise it?

I need help trying to format an external hard drive. My Mac won't recognise it anywhere other than System Profiler.

The problem is that it is a Western Digital 3.5 inch internal hard drive housed inside a hard drive caddy. So the only way to connect it to my computer is through a dock.

HT1338 I am still with 10.5.8 and my macbook does not show any software updates, i am willing to pay for a new software if it is needed, because i can't connect mi iPhone 5S or iPad mini to iTunes. PLEASE HELP!!!!!

How do i update 10.5.8 if my macbook does not show any software updates?

Upgrading to Snow Leopard
You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard - Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.
     Snow Leopard General Requirements
       1. Mac computer with an Intel processor
       2. 1GB of memory
       3. 5GB of available disk space
       4. DVD drive for installation
       5. Some features require a compatible Internet service provider;
           fees may apply.
       6. Some features require Apple’s iCloud services; fees and
           terms apply.
Upgrading from Snow Leopard to Lion or Mountain Lion to Mavericks
To upgrade to Mavericks you must have Snow Leopard 10.6.8, Lion, or Mountain Lion installed. Purchase and download Mavericks (Free) from the App Store. Sign in using your Apple ID. The file is quite large, over 5 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
     OS X Mavericks- System Requirements
       Macs that can be upgraded to OS X Mavericks
         1. iMac (Mid 2007 or newer) — Model Identifier 7,1 or later
         2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) —
             Model Identifier 5,1 or later
         3. MacBook Pro (Mid/Late 2007 or newer) — Model Identifier 3,1 or later
         4. MacBook Air (Late 2008 or newer) — Model Identifier 2,1 or later
         5. Mac mini (Early 2009 or newer) — Model Identifier 3,1 or later
         6. Mac Pro (Early 2008 or newer) — Model Identifier 3,1 or later
         7. Xserve (Early 2009) — Model Identifier 3,1 or later
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
Are my applications compatible?
         See App Compatibility Table — RoaringApps.
Upgrading to Lion
If your computer does not meet the requirements to install Mavericks, it may still meet the requirements to install Lion.
You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
     Lion System Requirements
       1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
           or Xeon processor
       2. 2GB of memory
       3. OS X v10.6.6 or later (v10.6.8 recommended)
       4. 7GB of available space
       5. Some features require an Apple ID; terms apply.

Windows based WD external hard drive not showing up in Disk Utility to reformat to Mac... how can I erase the drive

We have a WD external harddrive previously used with a PC that we want to completely erase and reformat for use with our iMac desktop for use with Time Machine. The drive shows up on the desktop of the Mac, but it does not show up in Disk Utlity, assuming because it's Windows format. Outside of the standard "erase" feature in Disk Utility, is there any way to reformat this drive for Mac OS X? Or how can I get this drive to show up in Disk Utility? Note: The drive functions properly, has power, and we are able to view its current contents through the desktop icon, so it is a working drive. And we are ok with losing all the current data on the drive.

Hmm strange, I had just moved my external Lacie drive from my windows machine to my iMac and it was showing up in disk utility still formatted fat32 or whatever. I would disconnect the drive and restart the machine then replug the drive and try again.
Also not that it will make a difference ( I dont think it will but hey why not ) try accessing disk utility from the install disk?

I have a mid-2010 iMac and just purchased a 2TB TC, can't join existing wireless network with AC standard so attached to iMac via ethernet with TC wifi turned off. How do i access TC now? not showing up in disk utility or on desktop. working fine with TM

I have a mid-2010 iMac and just purchased a 2TB TC, I just found out that it can't join existing wireless network with new AC standard so attached to iMac via ethernet with TC's wifi turned off. How do i access TC now? not showing up in disk utility or on desktop. It is working fine with TM. My cheeper seagate drives etc kept crashing, so i didnt trust cheeper back up options anymore. Connected those drives to TM via firewire and could see the drives and access them.
Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed. I heard that bridging slows down everything and then there can be port issues with mail etc. I connect to the internet via airport only and it is pretty fast. Getting over 50mbs downloads and over 30mbs uploads. Plus everything in my home it connected to my fios router, airport express for music streaming, two apple tvs, vuezone camer system. I really didn't want to monkey around too much with my system. But are there other options to connect the new TC. Can't find info anywhere for this and called apple who gave me the info above. after hanging up, i see that i cant access my TC and I am wondering if i would have to reset it to turn wifi on again to make changes to the drive, turn off blinking light or repair it in disk utility if it should become corrupted.
For other with similar issues i did solve some other problems: when i connected it to my ethernet port on my iMac wifi stopped working. Found that I had to turn off the ethernet in the system>network screen, but then TM didn't see the TC so i restarted after changes and then it saw it.
Now a rant. I can't believe in this wireless age that Apple would make a product that cant join a wireless net work. The apple rep said i could return it and look for the previous TC that would join an existing wireless network. Are we going backwards?
Thanks!
lennydas

Ok... it is getting a bit clearer but there are still some questions.
I connect to the internet via airport only and it is pretty fast.
I was assuming airport in this statement in your first post meant the TC or the Express.. but I now realise we are still in the mass confusion stage where apple calls everything wireless an airport. So what you mean is the airport internal card of the computer??
Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed. I heard that bridging slows down everything and then there can be port issues with mail etc.
I think this is mistaken.
Putting the TC in bridge mode plugged into your FIOS will not slow the network.. nor will it cause mail or port issues.. in bridge the TC is just a fancy WAP and switch plus the network hard drive.
If the computer is close it will be faster than the FIOS.
You can run both wireless networks with different names.. so it is clear which is which. But you can also setup roaming so the computers themselves pick which is the best wireless.
I tried extending the wireless net work and tried joining wireless network, but the TC kept crashing and I had to keep resetting the TC. the Apple support person said these, extend wireless network and joint wireless network, are no longer a connection option with the new TC because of the new AC protocol.
Thanks again!
You cannot extend to a non-apple wireless router.
You cannot use join a wireless network because when you do the ethernet ports will be cut off.
But that has not changed.. I don't think Apple support is correct.. there has been no change with the AC model.. it is simply a fact that apple routers do not work in join wireless mode other than as a dumb client. The same applies to AC as to the earlier version.. but I have asked another person to check this.
Join in the express is the only apple router that still allows an ethernet connection.
For now you best use of the TC is bridged to the FIOS. Wireless you can sort out between several options.

Western Digital drive not showing up in disk utility--Help please.

Hello all. This is my first post. I am having trouble with my WD 500GB external hard drive. It is not showing up in disk utility when connected either via the firewire or USB ports. I purchased the drive about 8months ago, brought it home and set it up as my Time Machine backup drive. It worked great for several months, until it got full. Then it stopped showing up on the desktop for no apparent reason. I discovered through reading support documents on the Apple web site that when I set the drive up initially I should have changed the partitioning protocol from master boot record to GUID, but I did not. I followed the apple web site instructions for making the change expos facto, but was instructed to press buttons that were "grayed out". As such, I couldn't do it. Perhaps foolishly, I thought that I would just start all over by reinitializing it, formatting it correctly (with my new found knowledge) and then do the time machine backup fresh. However, the drive no longer shows up in disk utility no matter how or in what order I connect it. When the drive is connected by firewire there is evidence of some recognition of the drive in system profiler, but it is listed as "External HDD Buttons and Lights". There is also evidence of the My Book showing up at a minimal level (eg. the firmware revision and a few other details are listed). On the front of the drive is a ring of blue lights that progress in a clockwise direction as soon as a connection is made via either firewire or USB. Before that it is solid blue. I have read through all the info that I can find on this site, and all the suggestions require the drive being recognized in disk utility. Without that, I am stuck. I know this must be a solvable problem, because the drive just a bucket of parts before it was manufactured. I just don't know enough to solve the problem or even know what qeustion to ask. I would really appreciate some help. Thanks in advance, and sorry for the long post.

If you can't boot from an OSX DVD, it sounds bad. Yet I think you said you were running Disk Utility from the DVD?
I got an external Firewire drive enclosure for 2.5 inch IDE drives from Other World Computing (OWC)
http://eshop.macsales.com/item/Other%20World%20Computing/MOTGFW400/ but similar items are available from many vendors like Newegg. About $60 for the basic model. More money can buy additional interfaces on the enclosure like FW800 and USB2; an AC adapter instead of letting the firewire bus power the drive (usually OK).

MacBook does not see internal hard disk

Sorry if this is already answered somewhere, but I have searched so many forums that my head is swimming!
My boyfriend connected a new USB drive to his MacBook, formatted the new disk, copied some backup data onto it. At some point, the MacBook hung, so he held down the power key until the MB turned off.
Each time we restart it now, we get the flashing-folder-with-question-mark, and Tiger won't boot.
I have tried almost all of the tips I can find, and was even willing to reinstall OS X, however... the MacBook does not appear to see it's internal hard disk. As such, I cannot perform first aid on the disk via booting to setup DVD, and I cannot reinstall OS X.
If I boot from the OS X install disk, and use Disk Utility, the MB only sees the CD-RW/DVD-RW drive and the install disc. No internal HD ever shows up.
Help! I am at a loss as to how to fix...

Let me guess: you're also experiencing a low clicking noise from the right side of your mac immediately after you turn it on, right? Same thing happened to me and others, in fact there are several threads on this subject already:
http://discussions.apple.com/thread.jspa?threadID=960977&start=0&tstart=0
http://discussions.apple.com/thread.jspa?messageID=5325539&#5325539
My drive was done for, and no data could be saved. I ended up buying a new drive, and now I'm just hoping the same thing doesn't happen again. I'm beginning to get a sense that this problem is occurring on a more frequent level now that the 1st generation macbooks have reached their 1-year birthday, give or take. Let's hope Appel fesses up if it is indeed a design flaw.
Anyway, you most likely need a new drive. I just got a Hitachi Travelstar 250 gb for around 200$US, so they're quite cheap, and VERY easy to install, just 3 screws, slide it in, boot up, run disk utility, erase/format and you're good to go.

Trying to upgrade from OS9 to 10.2.3, get as far as "select a Destination" the installation stalls and does not show any destination disks

I have a Power Mac G4, it has OS 9. Imam trying to upgrade to OS 10.2.3 (Jaguar). It is going smoothly until I get to the "Select Destination" screen. It stalls there and does not show any disks to choose from.
Any ideas?
Thanks. Abe Oliver

Hello Abe,
If it's a Digital Audio or earlier, you need to install a Firmware update first...
As explained in "Mac OS X 10.2 Welcome and Install Manuals" and "Mac OS X Welcome and Install Manuals", you may need to update the firmware on your Macintosh computer prior to installing Mac OS X 10.2 or later. The following table lists the firmware updates that are available for Apple products that can update to Mac OS X 10.2 or later.
http://support.apple.com/kb/HT1395?viewlocale=en_US
Power Mac G4
Firmware Update
Download Document No.
Power Mac G4 (Mirrored Drive Doors 2003)
no update needed
Power Mac G4 (FW 800)
no update needed
Power Mac G4 (Mirrored Drive Doors)
no update needed
Power Mac G4 (QuickSilver 2002)
no update needed
Power Mac G4 (QuickSilver)
no update needed
Power Mac G4 (Digital Audio)
Power Mac G4 Firmware Update 4.2.8
120068
Power Mac G4 (Gigabit Ethernet)
Power Mac G4 Firmware Update 4.2.8
120068
Power Mac G4 (AGP Graphics)
Power Mac G4 Firmware Update 4.2.8
120068
Power Mac G4 (PCI Graphics)
no update needed
Power Mac G4 Cube
Power Mac G4 Cube Firmware Update 4.1.9
75129

OCZ Vertex 3 not showing up on Disk Utility (2011 17" Macbook Pro)

I have a problem with my 120GB Vertex 3 installed on my 2011 Macbook Pro. It wouldn't boot after the apple logo after using it for a while...I tried starting up my mac with safe mode, commad+c,command+v,and command+option+p+r but it didn't help.
So I took out the vertex form my mac and then replaced it with the original toshiba hard drive, opened disk utility but the vertex didn't even show up.
before that, I also tried booting with the mac os x disk (vertex inside the mbp) and opened disk utility from it but I had the same result.

Chris,
I had a similar problem. This was with a brand new Vertex 3 that I tried to install into the system. It would not be recognized by Disk Utility or Time Machine Restore from the OSX 10.6 boot CD.
Here is my solution to the problem:
1) I put the original 250GB HDD back into the system. I used Disk Utility to format it to only use the first 120GB of the disk, leaving the rest blank (OSX reserves a 200MB partition, so the exact size of the system partition is 119.69 GB (119,690,170,368 bytes)). You can always make it 1-2 GB smaller, to be safe.
2) I used Time Machine to restore the system onto the original HDD.
3) I placed the OCZ Vertex 3 into an external USB enclosure. I then re-booted the system into Gparted using a Linux live CD (http://gparted.sourceforge.net/)
4) I used the Linux command dd (http://enwikipedia.org/wiki/Dd_(Unix)) to make a byte-for-byte copy of the two disks. dd will stop when the Vertex 3 becomes full, so you need be absolutely sure that your partition is small enough.
Here is the dd syntax: if stands for input file (source disk), of stands for output file (target disk). It takes a really long time, and has no indication of its progress. You can tell it is working by seeing the external enclosure LED blink.
>dd if=/dev/sda of=/dev/sdb
dd is a standard UNIX command and comes with OSX too. You could always try this from the Terminal application from the OSX boot CD. I did it using Linux, because I am slightly more famailiar with Linux over Unix command line.
The internal (standard HDD) hard drive should be mounted on sda. The Vertex 3 (inside the USB enclosure) might be sdb, but if there are other disks present it might not be. Use dd with extreme caution! I highly suggest that you detach all other disks (such as the Time Machine disk) before attempting this. If you set of= to the wrong disk, it will completely wipe it out.
5) Swap drives. Computer boots, everything works!
6) (Optional)... if you made the partition smaller than the Vertex 3, you can try to resize it to use the full capacity of the disk with Disk Utility from within OSX.
Let me know if this was helpful. Send me a reply or PM if you need any more detailed instructions. I would be glad to help.
-Sam

Partition does not show as startup disk

I have partitioned my iMac drive and have snow leopard on HD and Yosemite on HD2. When I go to change to the Yosemite partition (HD2) it does not show in systems available to startup from, even though it used to be there.

Mine doesn't either, or rarely (did in the past) so I just use Windows Boot Camp control panel where both do show up.
If you alter or resize or create a 3rd partition, that also can happen.
Some people use rEFIt boot manager, I never have and so can't comment on its utility, but might want to check it out.

IPod Touch not showing up in Disk Utility

Hello,
As my title says I can't get my iPod to show up in disk utility. It will show up in my iTunes fine, and works great but for some reason when I bring up Disk Utility, nothing shows up, as if it's not plugged in.
Thanks,
Chris Kefalas

Chris Kefalas wrote:
So my next thing to try was to take an image of Snow Leopard that I have, and put that onto my iPod touch and then boot off my iPod touch, and install it that way since my disc drive isn't working...
i wouldn't even consider doing that with an iPod classic. instead, i would get a cheap USB drive (better yet, a firewire drive), use *disk utility* to restore the image of the SL install disk to a small (10 gig) partition there, and boot from the external.
you could also use another Mac to do a *remote install*. click here for information.
yet another option, again involving another Mac, is to enable *remote disk*:
The CD/ROM in my computer busted, so I decided to try to remotely mount the CD from another computer on mine. I know the MacBook Air can do this, so I reasoned that any Mac could. It turns out it is possible, but the solution is far from obvious -- after much searching, I found the solution here.
Here's a quick synopsis. Go to System Preferences » Sharing, and enable 'DVD or CD Sharing.' (I think you need to do this on both machines -- the one with the drive and the one without the CD/ROM drive). Then, on the computer that does not have the CD drive on it, go to a Terminal window and enter:
$ defaults write com.apple.NetworkBrowser EnableODiskBrowsing -bool true
$ defaults write com.apple.NetworkBrowser ODSSupported -bool true
Reboot this machine, and when the reboot is finished, you'll see the remote CD/DVD under Devices in the Finder's sidebar. Thereafter, you can remotely mount a CD/DVD from another machine.
JGG

External HD not showing up in disk utility or finder even though the HD lights up and vibrates

So a while back I was trying to format my HD so I could back up my computer and watch movies etc. When i finished formatting it I tried plugging it in to the usb port but it didn't show up on my desktop, since it sometimes does this i went to disk utility to see if something was wrong but the only HD that showed up was my internal. Could someone please help me out with this because i really don't feel like buying a new hard drive

Hello there, obomb2000.
It sounds like your USB drive is not being recognized when you plug it into your Mac. The following Knowledge Base article offers some practical steps for troubleshooting:
USB and FireWire Quick Assist - Apple Support
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Portable Hard Drive will not show up in Disk Utility

I purchased a Toshiba Canvio Slim 500 GB hard drive a few months ago before I updated my computer to Mac OSX Version 10.6.8. I was running out of Hard Drive Space since I bought my computer in 2009 and decided to use a portable hard drive to store some of my personal information. I was able to read and successfully transfer data to the hard drive, but then I updated my computer to 10.6.8 and now I can't access it at all. It won't even show up in Disk Utility. I read on a few forums that some people were having the same problem as I was and they bought a y-cable adapter to power the hard drive through two usb cables. I bought one and tried it out and I'm still not having any luck. I tried using my girlfriend's computer to see if I can access it from her computer and it shows up in disk utility, but I can't access it. The lights turn on and I can hear it working like it worked the first day I used it, but nothing is happening. Please help me fix the problem.

Evidence, as scant as it is from Disk Utility, suggests the Toshiba external
HDD is indeed without Partion Map Scheme, has no files on it, unformatted.
So I wonder if there isn't a wire or defective circuit inside the box (enclosure)
that may be hiding access to the actual HDD unit inside there. Those kinds
of enclosures generally use a laptop 2.5" HDD since they can run on USB
power from the port. Matching up the internal HDD from that case, with an
other one with correct life support (connections) is a way to test it.
However if the Toshiba HD is a 3.5" standard drive, a larger enclosure, or
an adapter that simply plugs into the connections of the bare hard drive,
would be a way to access that external drive. These 'drive adapters' can
work with both SATA and IDE hard drives; or just one of the two. They
run in the range of $40 or so, and essentially are a wire kit with a power
adapter to spin the drive, but some do not even have the adapter, so as
to still use USB power for smaller drives of slower disc RPM speed.
Most competent computer stores with a skilled staff would know of these.
However some of the smaller HDD enclosures may be hard to open up.
And if there were a Toshiba warranty, this action could void the same.
Adapters would be to 'test the idea of recovering any data,' if enclosure
the drive shipped in has somehow developed a defect. Though it may
be if there is a defect, it may have existed at a point in time to affect
the actual save-to-disk process. Or later. A wire could be not allowing
information to be received, if broken or circuit damages, by the Mac.
But by the look of the Disk Utility's partition map, along with the other
earlier image that shows the same info in the bottom of the image of
the status, in Disk Description, this does not bode well for recovery.
I'm not sure what else to suggest. When the dust settles, Toshiba may
have a residual warranty that could only replace that one with another.
Some older mailorder catalogs show these kinds of adapters, some use
USB port power, others also include an AC adapter so standard faster
HDDs can be used without an enclosure. This also helps if one wants
temporary access to a hard disk drive, but does not want to install it.
•USB drive cable adapter kit SATA and IDE HDD - google results:
https://www.google.com/#q=USB+drive+cable+adapter+kit+SATA+and+IDE+HDD
Companies also make hot-swap docks to allow fast swapping of HDDs
of either or both 2.5" and 3.5" size, these have their own adapter and
one simply puts drives inside from the top, like a bread toaster.
Hopefully you can take the Toshiba along to a computer store and ask
a somewhat skilled person there about getting the cable adapter kit or
another enclosure. The cable adapter would cost less & be quicker, yet
that would still involve opening up the failed HDD's enclosure for access.
Good luck & happy computing!

Hard drive not showing up in disk utility

We had a couple power outages a few days ago.
But everything worked fine last night when I shut down.
Started up--no chime--and got question mark in folder flashing icon.
Started up with G5 OSX install disk 1. Ran Disk Utility and hard drive DOES NOT show up. Checked again and again. Same thing. Zapped PRAM and did the "X" key thing (according to Apple documents). Now it starts up with chime. Still no hard drive.
I read other older posts with similar problems. Sentiment was that the hard drive was fried.
I have most clients work backed up. But if I can retrieve their data, I'd give up the whole computer. I really need that data. What are my chances that the hard drive is gone? I don't want to spend alot of money with an apple tech out here if its probably dead. I'll just buy a new hard drive and start all over.
Took the Tech Tool disk that came with Apple Care (on another computer; I don't have Apple care on this G5) and ran diagnostics. It just hangs up at "Scanning Volumes" with nothing labeled in the Volume drop-down menu.
Please advise!

Yeah, dadof3, you were right. I dropped it off at a authorized repair shop in Evanston, IL (lapin systems) and they told me the bad news. So they're putting in a 250 GB startup drive w/a new Tiger system AND putting aside a new Lacie 250 GB external firewire drive for me.
Instead of archiving jobs once a month and never doing back-ups, I'll be backing up my production folders DAILY with that external drive. I'll unplug it from the power supply upon completion of the backup.
Thanks for the last-ditch suggestion. I'll do the freezer thing and then connect to bay 2. Meanwhile, I'll be calling clients and dreading revision or re-order requests from jobs started between September and now (gulp). At least I have backups on another computer for my latest jobs.
This was a terrible lesson. Bitter, yet humbling. To all those who use their computers to put food on the table, don't be a fool like me! NEVER go without daily backups for jobs in progress or jobs not archived.

WD 320GB in my macbook does not show reliably in Disk Utility

Similar Messages

Maybe you are looking for