WDS and WPA with 2x Express and 1 x Extreme - barbed wire in the *** easier

Frankly I am disgusted at the near impossibility of getting this to work after 5 hours of playing, resetting and stuffing around. Apple need to pull their fingers out and realise that "we make em simple so you don't need docs" is not going to cut it for everything.
Each time I get aways into this (got it working sans WPA after 3 hrs) I get either a non subnet IP address, or the Setup Utility can see but not open a station. No probs hard rests all around and awayyyyy we go again.
At this stage I will NEVER purchase a Airport base station again. My years with NetGear showed how it can be done properly.
If this keeps up, and factoring in my 2 day old dead iMac, I'm off to Dell for a complete technology refresh!
Has anyone ever got this simple configuration to work? if so can you point me at some doc or tips?
Forgive me for wanting security and wireless access at the same time!
Rant=off, apologies=on
regards Paul

Thanks Dwayne,
However I had already upgraded Firmware on all devices.
I actually solved the issue as follows:
1) The problem was that using the auto-config feaature of the Airport Admin Utility kept crashing as it tried to update the Main Base Station. It was in effect freezing in the rejoin and getting a 169.x private address - therefore unable to see the 10.0.x subnet of the network.
2) Use the auto-config, but once the Remote Base Station(s) are updated, power them off before the wizard gets to the Main Base Stattion.
3) It then manages to see the right subnet and can complete the update.
My guess is that this is an isue with more than 2 Airports and the very slow speed of the DHCP service on the Airport Extreme.
I am dissapointed to say the least.
Cheers
Paul

Similar Messages

Advice to extend range from Time Capsule - wireless and ethernet with Airport Express and Airport Extreme

Current wireless network is Time Capsule (connected to a Cisco router, 1GB switch to servers and printer 1) to Airport Express (wireless) and to Airport Extreme (wireless). Distance means poor signal at the Extreme which has 2 printers (ethernet cables) and an iMac (wireless)
Solution is to connect the Extreme to the Time Capsule via Cat 6 ethernet cable
How do I configure the TC and the Extreme?
I will keep the Express for a wireless extension to the TC

Wired Ethernet from the TC to the AirPort Extreme will result in much better performance. It sounds as if you are not configuring the AirPort Extreme correctly.
Please try the following steps carefully:
Unplug the Ethernet cable from the AirPort Exteme if it is not already unplugged. With the AirPort Extreme powered on, hold in the reset button on the Extreme for 10 seconds and release. Allow a full minute for the Extreme to restart
Connect the Ethernet cable to the WAN "O" port on the Extreme.
Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear. Just below that, click on AirPort Extreme.
The example below displays an AirPort Express. You will see AirPort Extreme.
AirPort Setup will open up automatically and take a minute to analyze the network, then announce that the Extreme will be configured to extend the Time Capsule network.
Enter a device name that you want to use for the Exterme and click Next
Wait a minute while AirPort Setup configures everything for you. When you see the message of Setup Complete, click Done.
That's it. Pretty simple. Things should be working fine now.

Assistance with Regular Expression and Tcl

Assistance with Regular Expression and Tcl
Hello Everyone,
I recently began learning Tcl to develop scripts for automating network switch deployments.
In my script, I want to name the device with a location and the last three octets of the base mac address.
I can get the Base MAC address by :
show version | include Base
Base ethernet MAC Address       : 00:00:00:DB:CE:00
And I can get the last three octets of the MAC address using the following regular expression.
([0-9a-f]{2}[:-]){2}([0-9a-f]{2}$)
But I have not been able to figure out how to call the regular expression in the tcl script.
I have checked several resources but have not been able to figure it out. Suggestions?
Ultimately, I want to set the last three octets to a variable (something like below) and then call the variable when I name the switch.
set mac [exec "sh version | i Base"] (include the regular expression)
ios_config "hostname location$mac"
Thanks for any assistance in advance.
Chris

This worked for me.
Switch_1(tcl)#set result [exec show ver | inc Base]
Base ethernet MAC Address       : 00:1B:D4:F8:B1:80
Switch_1(tcl)#regexp {([0-9A-F:]{8}\r)} $result -> mac
1
Switch_1(tcl)#puts $mac
F8:B1:80
Switch_1(tcl)#ios_config "hostname location$mac"
%Warning! Hostname should contain at least one alphabet or '-' or '_' character
locationF8:B1:80(tcl)#

I have East/West Symphony. Will it work with Logic express and do I have to have that little red usb drive in the computer to authorize it?

I have East/West Symphony.
Will it work with Logic express and do I have to have that little red usb drive in the computer to authorize it?
Also, would it work with Garageband??

Thanks-that's the same driver I'm using now.
The M-audio techs were unable to tell me if Quattro would work with LE8, so I've been wasting my time and money trying to make it work.
They also gave me conflicting opinions as to whether or not "tip" polarity was an issue when using an after-market adapter. One said definitely yes, one or two others said definitely no.
Their phone tech line has a 20 to 40 minute wait when I call. The online support system is confusing, which even they admit. I don't think my next interface will be from M-audio.
Thanks very much for the response, it helps me get beyond this phase.
Is the Quattro of any use for anybody else (i.e., can I sell it or give it away)?

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network?

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network? Network is administered through an iMac running OS X Yosemite 10.10.2. Ideally, would like for the second Airport Extreme hard drive to appear on the list of devices in the Finder window.

Ok.. gottcha
The problem is network wise.. Yosemite is about equal to tin cans and string.. pathetic.
Here is my usual set of instructions to get anything working on Yosemite.
The best way to fix problems is a full factory reset of all the AE in the network.
Factory reset universal
Power off the AE.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the AE to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg AEgen5 and AEwifi for basestation and wireless respectively.
Even better if the issue is more wireless use AE24ghz and AE5ghz with fixed channels as this also seems to help stop the nonsense.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the AE always takes the same IP address.. this is not a problem for AE which is router.. it is a problem for AE which is bridged.. you will need to set static IP in the main router by dhcp reservations or use static IP in the AE which is tricky.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric..
5. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
6. Now mount the disk of the second AE in finder... manually.
Use Go, Connect to Server and type in the AE ip address.
SMB://10.0.1.2
Where you will replace that address with the actual address. The network resource should be discovered and then it will request the password.. type that in and make sure you tick to save it in your keychain.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
Do as much as you want of the above... not all of it is necessary.. only if you want it reliable.. or as reliable as Yosemite in its current incarnation can manage.
The most important thing is point 6.. mount the disk using direct IP address and not names.. dns in Yosemite is fatally flawed.
See http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

My Outlook/iCloud calendar invites to others appear to work on my end and sync with my PC and mobile, but when other people "accept" the invite, it will not populate/add in to their calendar. How can i fix this without turning off iCloud?

My Outlook/iCloud calendar invites to others appear to work on my end and sync with my PC and mobile, but when other people "accept" the invite, it will not populate/add in to their calendar. How can I fix this without turning off iCloud?
I am at a new office that uses Outlook (not Outlook Exchange) which does not sync with my mobile... I just got iCloud set up on my PC to sync my contacts, calendar, reminders, etc... The sync worked (not without flaws, but the other issues seem solvable... I think), so that i can now see all my appointments on both my phone and on my PC. The problem I am having is that iCloud moved all of my calendar items from Outlook into iCloud calendar and now when I send out meeting/calendar invites the recipients may accept them, but the meeting does not get added to their calendar. This is a huge problem and may mean that i need to turn off iCloud.
Does anyone know how to fix this?
Thanks!

I am replying to my own post here as I seem to have fixed the problem.
I do have some calendars that are shared. Some of those are shared with users who have time zone support turned on. So i activated time zone support on my iphone, then deleted my icloud subscription. I then signed in to icloud again and voila... problem solved.
It is a weird one as the other calendar views were always fine and when you opened an event that appeared in the wrong day (on list view), the correct date of the event was shown in the information...
one more bug in a complicated system I guess

I had 3 versions of FF and had to redo the HD and now no version will install says "Can't open output file" i have winddows 7 64 bit 8 GB memory and 1T HD but i have it on my other desktop and laptop with less memory and HD space and works fine

I had 3 versions of FF and had to redo the HD and now no version will install says "Can't open output file" i have winddows 7 64 bit 8 GB memory and 1T HD but i have it on my other desktop and laptop with less memory and HD space and works fine laptop has windows 7 64 bit and other desktop hook to my 32" tv has win 7 32-bit i lso did clean removal of all versions of FF and did new DLs with screen shots of it DLing, complete of DL and after i got the error again.

i am posting this as a reply due to it would not allow me to attach screen shots except for this way

I have upgraded my iPhone 4s to iOS7. Now my podcasts I have added to ITunes and synced with iPhone do not open. When I touch the screen like in the old iOS6, nothing happens.

I have upgraded my iPhone 4s to iOS7. Now my podcasts I have added to ITunes and synced with iPhone do not open. When I touch the screen like in the old iOS6, nothing happens. What is the solution?

Hello irish3kr,
You may need to download and install the Podcasts app.
About the Podcasts app for iOS
http://support.apple.com/kb/HT5295
Cheers,
Allen

I have a MBP 15" with iPhoto 9. When right clicking on icon in dock 3 iPhoto libraries come up; one empty, one with 35,000 photos and one with 30,000 photos. How can I delete the empty one and merge the other two without getting duplicates?

I have a MBP 15" with Iphoto 9. When I right click on icon in dock 3 iPhoto libraries come up; one empty, one with 35,000 photos and one with 30,000 photos. How can I delete the empty library and merge the other two without getting duplicates?

You can delete the empty one by dragging it to the trash ( test everything before emptying the trash)
Merging libraries requires iPhoto Library Manager - http://www.fatcatsoftware.com/iplm/ - it is the only current solution to merging libraries
LN

Firefox memeorised my username and password with a shared laptop. How do i erase the memorised information?

Firefox memeorised my username and password with a shared laptop. How do i erase the memorised information?

Hello if you go to the tools at the top of the screen and click on it.
Then you go to the options in that list and click on it.
Then you select security its the padlock its the last but one in the list click on it.
In that list you will have the options for the saved passwords click on this and then you can remove them.
please note this is not a secure way to save your pass words.
i would not use this.
if you would like to save pass words try [http://passwordsafe.sourceforge.net/ and its free.
hope this helps

How can I exchange my pc created documents on Excel, Word, and PowerPoint with my mac and my Pages, Numbers and Keynote created content with my pc? I need to create and edit between both.

How can I exchange my pc created documents on Excel, Word, and PowerPoint with my mac and my Pages, Numbers and Keynote created content with my pc? I need to create and edit and exchange between both types of operating systems.

Your Windows system will not open any Pages, Numbers or Keynote documents. No applications exist for Windows that can open those formats. You will need to export your documents in Word, Excel and PowerPoint formats, respectively, before you'll be able to view and edit the documents on your Windows system. The iWork documents can natively open Word, Excel and PP documents, though there are limitations on what can be imported (for instance, Numbers does not support all possible Excel functions). Consult the documentation for the relevant iWork application for details on importing and exporting.
If you are asking how to get the documents from one system to the other, then there are several ways to do that, including file sharing, using an external drive (hard drive, USB flash drive), or emailing the documents to yourself. Which would be best for your situation I can't say without more details about your usage.
Regarsd.

Hi there i have ipod touch 2nd gen and i am tryna restore it but i get error 21 with orginal fireware and 1601 with custom fireware and when it connected to itunes and i try to boot it up by restoring it white screen with lines thorugh it

hi there i ahve ipod touch 2nd gen and i am tryna restore it but get error 21 with orginal fireware and 1601 with custom firewarw and when connected it to itunes and i try to boot it by resotring it white screen with lines through it

Those errors are covered here:
http://support.apple.com/kb/TS3694

I need help integrating Microsoft Office, Outlook and Calendar with my job and is it possible

Ok guys I am new to the iphone 4s. I just dumped my Blackberry after 10 years. I need help integrating Microsoft Office, Outlook and Calendar with my job and is it possible? Also I need it to automatically push email and appointments to my phone? I will buy any app just need to know which is best for work environment. Here is what I am thinking about doing. http://www.groovypost.com/howto/apple/sync-iphone-or-ipod-touch-calendar-and-con tacts-with-google/ Is this the best way? For personal use I am using paid G whiz app

I use Google Calendar Sync to sync my work Outlook calendar to a gmail account, then sync that to my iPhone. It works well for me for the past couple of years.
As far as mail itself, just ask your it folks for settings for remote access to your exchange account, and then set it up on the phone.
As far as working with Office docs, to be able to actually edit them and such, look in the app store for DocsToGo or QuickOffice - they both are good but each has it's pros and cons, so on balance it's down to mere preference i think.

Cleaned files and apps with "app cleaner" and now MacBook Air turns off during start up. What happens? What can I do? Please help

Cleaned files and apps with "app cleaner" and now MacBook Air turns off during start up. What happens? What can I do? Please help

The "app cleaner" managed to do bad things to the file system so that it is unable to boot any longer.
This is the primary reason I always recommend that any of those so called "cleanup" apps never be used. They do more harm then good.
Try a safe boot by holding down the shifgr key when you hear the boot chime. Maybe that can fix the damage.
Let us know what happens.
Allan

HT204400 I used my apple tv wirelessly and it worked fine,then I plugged an Ethernet wire into the Apple TV to move it and could not it to connect. When I unplugged Ethernet wire it will not give me a wireless option. How do I get that back?

I used my apple tv wirelessly and it worked fine,then I plugged an Ethernet wire into the Apple TV to move it and could not it to connect. When I unplugged Ethernet wire it will not give me a wireless option. How do I get that back?

If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
    1.    Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
    2.    Connect the micro USB cable to the Apple TV and to your computer.
    3.    Reconnect the power cable (only for Apple TV 3)
    4.    Open iTunes.
    5.    Select your Apple TV in the Devices list, and then click Restore.
(You may already have a micro USB cable if you have a camera or other digital device)

WDS and WPA with 2x Express and 1 x Extreme - barbed wire in the *** easier

Similar Messages

Maybe you are looking for