WDS problem, Deauthenticating with station 00:1f:f3:c4:9d:07(reserved 2).

Hi
I'm working a on problem with a WSD-network, consisting of 3 brand new devices, a Timecapsule, an Airport Extreme and an Airport Express, all running the latest firmware, 7.4.1.
I've configured the Airport Extreme to be the main-station connected to the internet. When I add a second device to the WDS, I get the following in the log on either the AE or AX, depending on which devices is connected.
Mar 12 16:26:13 Severity:5 Deauthenticating with station 00:1f:f3:c4:9d:07 (reserved 2).
Mar 12 16:26:15 Severity:5 Associated with station 00:1f:f3:c4:9d:07
Mar 12 16:26:19 Severity:5 Disassociated with station 00:1f:f3:c4:9d:07
I've tried resetting all devices to default, doing manuel and guided installs, running with 2 or 3 devices, but I still get the errors, and an unstable network.
At times it seems like there's a network-loop, as a constant 'ping' increases in latency over time from 20ms to 10.000ms, but reconnecting one of the devices, seems to fix this problem at random.
Main(Airport Extreme) is running 802.11n(b/g compatible), as there's no other options.
I'm using WPA2 Personal as security.
Any clues to the problem is much appreciated,
Best regards
Nicolai
Message was edited by: NicolaiG

Having a very similar issue as well. I am using an Airport Extreme as my base station, with two Airport Express units, one as a relay and one as a remote. My house is pretty big, so the remote is actually out of the range of the Extreme base station, hence the relay, which sits halfway in between. I have an office in the house that is in the room with the remote Express, and every 15 minutes or so, like clockwork, I have to turn off the airport in my iMac, then turn it back on to get connectivity restored. All while the light on all the devices remain green. The signal will just drop, the airport utility will see absolutely nothing. I've spent the last two weeks going through all the google hits, and forums with this issue, and nothing seems to have worked. Good luck guys, it looks like with all the great things Apple has done, they must be really stumped on this one, for no resolution has ever surfaced that was the end all be all fix. Here's a look at my log from the AE in the office:
Mar 18 17:41:32 Severity:5 Associated with station 00:1d:d8:ae:02:58
Mar 18 17:41:33 Severity:5 Associated with station 00:1d:d8:ae:02:58
Mar 18 17:41:33 Severity:5 Installed unicast TKIP key for supplicant 00:1d:d8:ae:02:58
Mar 18 17:41:43 Severity:5 Disassociated with station 00:1d:d8:ae:02:58 (leaving service set).
Mar 18 17:41:46 Severity:5 Associated with station 00:1d:d8:ae:02:58
Mar 18 17:42:08 Severity:5 Deauthorizing station 00:1d:d8:ae:02:58 [15]
Mar 18 18:17:57 Severity:5 Rotated TKIP group key.
Mar 18 18:36:13 Severity:5 Clock synchronized to network time server time.apple.com (adjusted -0 seconds)
Mar 18 19:02:16 Severity:5 Connection accepted from ::ffff:10.0.1.5/50157.
Mar 18 19:12:35 Severity:5 Re-associated with station 00:1c:b3:71:85:b7
Mar 18 19:12:36 Severity:5 Disassociated with station 00:1c:b3:71:85:b7 (received invalid class-3 frame).
Mar 18 19:17:57 Severity:5 Rotated TKIP group key.
*The station (Mac address ending in 02:58) is the AE in my living room, which is the relay.
*The station (Mac address ending in 85:b7) is my iMac.
** I even had to power cycle my airport card just to post this message, to give an idea on how frequently this is happening.

Similar Messages

  • Suddenly started getting ' Deauthenticating with station .... (reserved 2)'

    A problem just started today when I brought home my iPad-2 (working fine).  I have an a 2TB time capsule (version 7.5.2) that suddenly started refusing our two iPhone wifi connections with ' Deauthenticating with station .... (reserved 2)'.  They worked fine until today. I can't figure out why this is happening and not sure if it is related to the new iPad-2. We have iPad 1 and 2's that are working fine.  The time capsule log shows one other MAC that is also getting the 'Deauthenticating with station' msg, I am not sure what device it is and not sure if that has always been happening or not.  My iPhone wifi worked fine at the Apple store and at a local Starbucks.  Everything has worked perfectly until today.  The timecapsule shows a normal status.
    Suggestions?

    Please ignore my post, I just rebooted the timecapsule one more time and our iPhones suddenly started connecting successfully again. I don't have a clue why this reboot fixed it but I'm not complaining.  Sorry about the spam.

  • Internet connection dropping out throughout day; problem NOT with provider

    My computer's connection to the Airport Express base station has no problems at all. But the internet connection goes out literally dozens of times a day (at no predictable schedule); this has been happening for almost a month. I originally thought the problem was with the internet provider, but I'm now beginning to think that either my settings are wrong, or that I have a corrupt file somewhere. Here are the details:
    I connect via a cable modem (Time Warner - Road Runner). I know people have had problems with Time Warner, so I assumed that was the issue; however I've had 3 service calls and they've checked signal strength inside and out, and swapped out the modem and the cables. I don't think it is simply problems in our geographic area (i.e. greater Los Angeles) due to the fact that the Internet fails sometimes 40-50 times daily, and the problem began when I upgraded from an old Airport base station to a brand new Airport Express about a month ago.
    The airport/internet connection is shared 3 ways: two MacBook Pro computers and one iPhone. My Airport's internet settings are as follows:
    Configure IPv4 using DHCP.
    DNS Servers: 66.75.160.63 and 66.75.160.64 (note I have already tried swapping these for OpenDNS -- this did NOT solve the problem)
    Domain name: socal.rr.com
    DHCP Client ID: [blank]
    Ethernet WAN port: Default-Automatic
    Connection Sharing: Share a Public IP address
    DHCP Beginning Address: 10.0.1.2
    Ending Address: 10.0.1.200
    DHCP Lease: 4 hours
    NAT settings are all unchecked
    One of the main reasons I believe that the problem is with my computer's settings or a corrupt file is that I can fix the problem whenever the Internet "goes down" almost 100% of the time by doing the following: after loading Airport Utility, I make ANY trivial change (i.e. changing the DHCP lease from 4 hours to 5 hours) and then click UPDATE to refresh the Airport base station. This fixes the problem almost 100% of the time. But then, anywhere from 10 minutes to 3 hours later, the Internet connection goes down again. [Unplugging the power from the modem, waiting 30 seconds, and plugging it back in ALSO fixes the problem almost 100% of the time, until it goes out again a little while later.]
    Also, I have tried disconnecting Airport and connecting directly to the cable modem via Ethernet. The problem remains exactly the same -- I can connect, but then the connection fails soon after. Unplugging then replugging the modem fixes the problem temporarily. So I do not think the problem is a defective Airport base station, nor do I think it is the modem (which has been replaced), nor Time Warner.
    I can't think of what else to try -- but any advice would be greatly appreciated -- it's impossible for us to work with the Internet constantly going out throughout the day, every day.
    Thank you!

    Just in case I'm missing something obvious, I am here pasting all CONSOLE messages that appear when I do a standard RESTART:
    8/22/08 7:15:12 AM loginwindow[24] DEAD_PROCESS: 0 console
    8/22/08 7:15:12 AM shutdown[128] reboot by mark:
    8/22/08 7:15:12 AM shutdown[128] SHUTDOWN_TIME: 1219414512 407699
    8/22/08 7:15:12 AM com.apple.loginwindow[24] Shutdown NOW!
    8/22/08 7:15:12 AM com.apple.loginwindow[24] System shutdown time has arrived
    8/22/08 7:15:12 AM mDNSResponder mDNSResponder-171.4 (Apr 20 2008 11:59:52)[23] stopping
    8/22/08 7:15:12 AM com.apple.SystemStarter[17] Stopping Adobe Version Cue CS2
    8/22/08 7:15:31 AM kernel npvhash=4095
    8/22/08 7:15:31 AM com.apple.launchctl.System[2] launchctl: Please convert the following to launchd: /etc/mach_init.d/chum.plist
    8/22/08 7:15:31 AM com.apple.launchctl.System[2] launchctl: Please convert the following to launchd: /etc/mach_init.d/dashboardadvisoryd.plist
    8/22/08 7:15:31 AM com.apple.launchctl.System[2] launchctl: Please convert the following to launchd: /etc/mach_init.d/pilotfish.plist
    8/22/08 7:15:31 AM com.apple.launchd[1] (com.adobe.versioncueCS3) Unknown key: ServiceDescription
    8/22/08 7:15:31 AM com.apple.launchd[1] (com.apple.distccdConfigd) Unknown key: SHAuthorizationRight
    8/22/08 7:15:31 AM com.apple.launchd[1] (org.cups.cupsd) Unknown key: SHAuthorizationRight
    8/22/08 7:15:31 AM com.apple.launchd[1] (org.ntp.ntpd) Unknown key: SHAuthorizationRight
    8/22/08 7:15:31 AM kextd[10] 413 cached, 0 uncached personalities to catalog
    8/22/08 7:15:31 AM kernel hi mem tramps at 0xffe00000
    8/22/08 7:15:31 AM kernel PAE enabled
    8/22/08 7:15:31 AM kernel 64 bit mode enabled
    8/22/08 7:15:31 AM kernel Darwin Kernel Version 9.4.0: Mon Jun 9 19:30:53 PDT 2008; root:xnu-1228.5.20~1/RELEASE_I386
    8/22/08 7:15:31 AM kernel standard timeslicing quantum is 10000 us
    8/22/08 7:15:31 AM kernel vmpagebootstrap: 972190 free pages and 76386 wired pages
    8/22/08 7:15:31 AM kernel migtable_maxdispl = 79
    8/22/08 7:15:31 AM kernel 98 prelinked modules
    8/22/08 7:15:31 AM kernel AppleACPICPU: ProcessorApicId=0 LocalApicId=0 Enabled
    8/22/08 7:15:31 AM kernel AppleACPICPU: ProcessorApicId=1 LocalApicId=1 Enabled
    8/22/08 7:15:31 AM kernel Loading security extension com.apple.security.TMSafetyNet
    8/22/08 7:15:31 AM kernel calling mpopolicyinit for TMSafetyNet
    8/22/08 7:15:31 AM kernel Security policy loaded: Safety net for Time Machine (TMSafetyNet)
    8/22/08 7:15:31 AM kernel Loading security extension com.apple.nke.applicationfirewall
    8/22/08 7:15:31 AM kernel Loading security extension com.apple.security.seatbelt
    8/22/08 7:15:31 AM kernel calling mpopolicyinit for mb
    8/22/08 7:15:31 AM kernel Seatbelt MACF policy initialized
    8/22/08 7:15:31 AM kernel Security policy loaded: Seatbelt Policy (mb)
    8/22/08 7:15:31 AM kernel Copyright (c) 1982, 1986, 1989, 1991, 1993
    8/22/08 7:15:31 AM kernel The Regents of the University of California. All rights reserved.
    8/22/08 7:15:31 AM kernel MAC Framework successfully initialized
    8/22/08 7:15:31 AM kernel using 16384 buffer headers and 4096 cluster IO buffer headers
    8/22/08 7:15:31 AM kernel devfsmakenode: not ready for devices!
    8/22/08 7:15:31 AM kernel IOAPIC: Version 0x20 Vectors 64:87
    8/22/08 7:15:31 AM kernel ACPI: System State [S0 S3 S4 S5] (S3)
    8/22/08 7:15:31 AM kernel mbinit: done
    8/22/08 7:15:31 AM kernel Security auditing service present
    8/22/08 7:15:31 AM kernel BSM auditing present
    8/22/08 7:15:31 AM kernel rooting via boot-uuid from /chosen: 419B2954-20DC-3880-AFEB-448924F9BE09
    8/22/08 7:15:31 AM kernel Waiting on <dict ID="0"><key>IOProviderClass</key><string ID="1">IOResources</string><key>IOResourceMatch</key><string ID="2">boot-uuid-media</string></dict>
    8/22/08 7:15:31 AM kernel FireWire (OHCI) TI ID 8025 built-in now active, GUID 001d4ffffe5f8d30; max speed s800.
    8/22/08 7:15:31 AM kernel Got boot device = IOService:/AppleACPIPlatformExpert/PCI0/AppleACPIPCI/SATA@1F,2/AppleICH8AHCI/PR T0@0/IOAHCIDevice@0/AppleAHCIDiskDriver/IOAHCIBlockStorageDevice/IOBlockStorageD river/ST9160823AS Media/IOGUIDPartitionScheme/Customer@2
    8/22/08 7:15:31 AM kernel BSD root: disk0s2, major 14, minor 2
    8/22/08 7:15:31 AM kernel Jettisoning kernel linker.
    8/22/08 7:15:31 AM kernel Resetting IOCatalogue.
    8/22/08 7:15:31 AM kernel GFX0: family specific matching fails
    8/22/08 7:15:31 AM kernel Matching service count = 1
    8/22/08 7:15:31 AM kernel Matching service count = 2
    8/22/08 7:15:31 AM kernel Matching service count = 2
    8/22/08 7:15:31 AM kernel Matching service count = 2
    8/22/08 7:15:31 AM kernel Matching service count = 2
    8/22/08 7:15:31 AM kernel Matching service count = 2
    8/22/08 7:15:31 AM kernel Previous Shutdown Cause: 5
    8/22/08 7:15:31 AM kernel NVDANV50HAL loaded and registered.
    8/22/08 7:15:31 AM kernel ath_attach: devid 0x24
    8/22/08 7:15:31 AM kernel GFX0: family specific matching fails
    8/22/08 7:15:32 AM kernel Override HT40 CTL Powers. EEPROM Version is 14.4, Device Type 5
    8/22/08 7:15:33 AM kernel mac 12.10 phy 8.1 radio 12.0
    8/22/08 7:15:33 AM kernel CSRHIDTransitionDriver::start []
    8/22/08 7:15:34 AM kernel CSRHIDTransitionDriver::switchToHCIMode legacy
    8/22/08 7:15:36 AM bootlog[38] BOOT_TIME: 1219414527 0
    8/22/08 7:15:36 AM rpc.statd[19] statd.notify - no notifications needed
    8/22/08 7:15:37 AM com.apple.launchd[1] (com.apple.distccdConfigd[32]) Exited with exit code: 255
    8/22/08 7:15:37 AM DirectoryService[34] Launched version 5.4 (v514.21)
    8/22/08 7:15:37 AM fseventsd[28] bumping event counter to: 0x2e4ba71 (current 0x0) from log file '0000000002e4b394'
    8/22/08 7:15:37 AM mDNSResponder mDNSResponder-171.4 (Apr 20 2008 11:59:52)[23] starting
    8/22/08 7:15:38 AM kernel yukon: Ethernet address 00:1b:63:a2:29:d1
    8/22/08 7:15:38 AM kernel AirPort_Athr5424ab: Ethernet address 00:1c:b3:c0:f5:49
    8/22/08 7:15:38 AM /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[24] Login Window Application Started
    8/22/08 7:15:38 AM com.apple.SecurityServer[20] Entering service
    8/22/08 7:15:38 AM /usr/sbin/ocspd[62] starting
    8/22/08 7:15:39 AM kernel 11D beacon causing regdomain change to CC 840
    8/22/08 7:15:39 AM kernel en1: 802.11d country code set to 'US'.
    8/22/08 7:15:40 AM kernel en1: Supported channels 1 2 3 4 5 6 7 8 9 10 11 36 40 44 48 52 56 60 64 149 153 157 161 165
    8/22/08 7:15:39 AM configd[36] setting hostname to "Macintosh-3.local"
    8/22/08 7:15:44 AM kernel USBF: 16.757 AppleUSBHubPort: Port 1 of Hub at 0x1a000000 about to terminate a busy device (IOUSBCompositeDevice) after waiting 10 seconds
    8/22/08 7:15:44 AM kernel USBF: 17. 59 CSRHIDTransitionDriver[0x723ca80](IOUSBCompositeDevice) GetFullConfigDescriptor(0) returned NULL
    8/22/08 7:15:44 AM kernel CSRHIDTransitionDriver... done
    8/22/08 7:15:46 AM kernel AppleYukon2: 00000000,00000000 sk98osx_dnet - recovering from missed interrupt
    8/22/08 7:15:46 AM org.ntp.ntpd[14] Error : nodename nor servname provided, or not known
    8/22/08 7:15:46 AM ntpdate[70] can't find host time.apple.com
    8/22/08 7:15:46 AM ntpdate[70] no servers can be used, exiting
    8/22/08 7:15:53 AM kernel AppleYukon2: 00000000,00000000 sk98osx_dnet - recovering from missed interrupt
    8/22/08 7:15:53 AM kernel AirPort: Link Up on en1
    8/22/08 7:15:54 AM kextd[10] writing kernel link data to /var/run/mach.sym
    8/22/08 7:16:02 AM loginwindow[24] Login Window Started Security Agent
    8/22/08 7:16:02 AM SecurityAgent[88] User info context values set
    8/22/08 7:16:02 AM SecurityAgent[88] Login Window done
    8/22/08 7:16:02 AM loginwindow[24] Login Window - Returned from Security Agent
    8/22/08 7:16:02 AM loginwindow[24] USER_PROCESS: 24 console
    8/22/08 7:16:02 AM com.apple.launchd[1] (com.apple.UserEventAgent-LoginWindow[81]) Exited: Terminated
    8/22/08 7:16:02 AM com.apple.launchctl.Aqua[91] launchctl: Please convert the following to launchd: /etc/machinit_peruser.d/com.adobe.versioncueCS3.monitor.plist
    8/22/08 7:16:02 AM com.apple.launchctl.Aqua[91] launchctl: Please convert the following to launchd: /etc/machinit_peruser.d/RemoteUI.plist
    8/22/08 7:16:03 AM com.apple.launchd[66] (0x101260.VersionCueCS3monitor) Failed to check-in!
    8/22/08 7:16:03 AM /System/Library/CoreServices/coreservicesd[44] SFLSharePointsEntry::CreateDSRecord: dsCreateRecordAndOpen(Mark's Public Folder) returned -14135

  • Time Capsule WDS Problem After Firmware (7.6.1) Update

    Some time ago, when I first setup my Time Capsule, setting up WDS with it and my Express went really smoothly - really impressed how it went.
    I applied an firmware update last night 7.6.1 to the TC and the AE. What a mistake. I've spent most of the morning trying to get WDS to work correctly. AE can't find TC with WDS, WDS error on TC when ever I change it's settings - it's flashing yellow now even though not 10 minutes ago everything was fine? It's a shame because each device has worked perfectly for over a year - when ever I installed them.
    Can anyone shed any light on the WDS problem? Has anyone else experienced any problems since the update?
    I've been reading about "Extending The Network" with wireless-N, supposed to be much easier, but not all my devices are N rated. Also I know for a fact that the first time I set this (WDS) up it was so easy - the "wizard" configured everything within 15 minutes. It's almost as if the option automatically setup WDS has been removed. Am I imagining things?

    I tried to change some settings on the TC and the AE would no longer connect. It seems everytime I make changes to either the TC or the AE it cause (yellow flashing light) problems. Decided to fall back to firmware 7.6, I've successfully managed to update settings on the TC without there being any problems.
    Don't want to waste any more time messing about with network, fingers crossed until the next firmware update.

  • Problem communicating with Airport express

    I have had a smal home network for some time. Set up is AEBS, AXBS as client to use airtunes to the stereo, an iMac that connects via wire to the AEBS, and a wireless Macbook. No security enabled. Today I was streaming some music, and burning some cd's with the macbook, when I noticed a very strange thing in the istat pro widget. In the network section it read in: 1 mb , out 104 mb. The computer had acted strange, as in very slow, so I freaked out and suspected someone was connected to my network and sucking info (or something) out of it. So I went ahead and enabled WEP security. Everything worked fine with the Macbook and the AEBS, even with the iMac, but I can't get pass a "there is a problem communicating with the base station" when I tried to change the settings in the AXBS. I tried to do it wireless and through internet to no avail...
    I hope some onecan point me in the right direction
    thanks in advance

    2 Possibilities:
    1) AirPort Utility on your computer has become corrupted. Delete the current application located Macintosh HD > Applications > Utilities > AirPort Utility, restart your computer and then reinstall the application.
    http://support.apple.com/downloads/#airport
    2) The AirPort Express device is not fully resetting to factory defaults due to an internal component problem. If you've tried the factory default reset a number of times and still can't configure the device, it will need to be replaced.

  • Has Apple acknowledged the problem yet with itunes aborting preview of songs after about 10 seconds on windows 7 and if so is there an answer other than ipconfig?

    Has Apple acknowledged the problem yet with itunes aborting preview of songs after about 10 seconds on windows 7 and if so is there an answer other than ipconfig?  IPConfig /flushdns doesn't help at all.  Until they fix it I will be previewing and buying my songs thru Amazon.

    Doublechecking ... do you still get that if you update to iTunes 10.6.3.25 (just released today)?
    http://www.apple.com/itunes/download/

  • Problem is with my iPhoto on my Macbook air.  I am trying to move my library from my airbag onto my passport drive.  I did it and deleted it from the airbag but it simply re appeared possibly from the cloud. Not sure what to do next.

    The problem is with my iPhoto on my Macbook air.  I am trying to move my library from my airbook onto my passport drive.  I did it and deleted it from the airbook but it simply re appeared possibly from the cloud. Not sure what to do next. Sorry I am not a techie.

    Sorry - we can not see you
    what do you have? Version of iPhoto? Of the OS? How is the passport connected to your Mac? What format is the passport (for the iphoto library it must be Mac OS extended (journaled)  )?  The iPhoto library is not and can not be on the cloud (maybe later with the Photos Application)
    LN

  • I get an error message when trying to install windows 7 on my macbook pro. The message says "windows has encountered a problem communicating with a device connected to your computer. I don't have anything connected to my computer. How do I fix this?

    I'm trying to install windows 7 on my macbook pro. I went through the process of bootcamp telling it to install windows 7. Once the windows boot manager started an error message came up. The error message says " windows has encountered a problem communicating with a device connected to your computer. I don't have a usb connected to my computer. I  am using windows 7 professional install disc. I  can't figure out what i am doing wrong. The same message keeps coming up over and over. Am I doing something wrong or is it something else?

    Well, shucks, i just spent almost 30 minutes trying to find your model user guide to explain it better, I guess they never got around to making it.....
    I would just borrow another Windows disk and try installing it again and if it does it again then you might take it to an Apple Store and see if one of the "Genius' " can figure it out.
    Make sure your internet is enabled and click on your blank desktop and at the top of your screen is a Help menu option, enter PRAM and it should give you a list of things relating to Pram. It may take a few seconds to list anything as it has to connect to Apples severs first. It should list the things you may have to fill back in when your done.
    "P-ram" stores some common information that is used in the background, your date, time, startup disk, etc, that you don't have to re-fill when you restart, it's a little different for each computer.

  • Problems only with Adobe ImageReady Animated GIF

    Anyone encounter a problem and solution for getting ImageReady animated GIF working properly in a java app? Developer placed 2 animated gifs in the app which caused the CPU system resources to spike to 100%.
    We then tested animated GIFs made from Macromedia Flash and also a freeware animated GIF editor, and both work out fine in the same java app.
    It's odd, but we think there's a problem specifically with animated GIFs produced by Adobe's Image Ready in the Creative Suite 1 package.
    Anyone have more insight?

    Its been a long time since I have used ImageReady, and then it was for about year when CS3 came out. So my memory if very rusty with that program. (In other words I am hoping that I am not too far off base, lol.)
    Check and make sure there are the same number of layers as there are frames. I believe there is an option in the animation palette for sending the frames to layers. Once you know that the frames and layers match (plus any additional layers you create), you can clear out the animation and reapply the layers to frames.
    You should find a small icon in the upper right hand corner of the animation palette and the layers palette. Clicking them will bring up a menu that will do what you need.

  • Safari keeps crashing every time I try to open a link from a different application, i.e. Mail. The trouble report says that some problem occurs with libcooliris.dylib plug-in. Can any one help?

    Safari keeps crashing every time I try to open a link from a different application, i.e. Mail. The trouble report says that some problem occurs with libcooliris.dylib plug-in. Can any one help?
    Thanks!

    Dear Linc,
    Thank you for the advice, John Blanchard1  and Linc Davis
    As suggested in your reference thread I removed "/Library/Printers/hp/PDEs/hpPostScriptPDE.plugin" and the problem has been resolved.
    I am guessing the the plug-in for the hp printers got corrupted and effected every thing, or became unsuitable when I installed an Apple update. I would be most grateful if you can confirm how the problem was coursed so I can understand and learn from this experiance.
    Ash

  • Solution to problems synchronizing with Mercedes C...

    Warning: this is long but worths reading if you have trouble synchronizing your Nokia's phone book/addressbook with COMAND APS.
    I have spent hours looking on Mercedes and Nokia forums for my problem and did not find a posted solution. I have now found a solution myself so I decided to post here hoping it will help other people.
    First my issue: I have an E-Class W211 (Apr 2005, UK) with phone pre-wiring, the Mercedes SAP v2 cradle and a Nokia E61i (S60 3rd edition). Till about a week ago the whole was working perfectly: was able to make/receive calls, read/send SMS, synchronize the phone's and SIM contacts to the COMAND, etc.
    About a week ago I upgraded the firmware on my phone to overcome some other (irrelevant to this) issues I had. When I got into my car after the phone's firmware upgrade I naturally needed to pair the phone with the COMAND/SAP Cradle. I did everything according to the manual that came with the SAP v2 Cradle and thought all would be good again. Then, I try to re-sync the COMAND's address book with that of my phone's by following the manual's procedure (dial 0000).
    The synchronization started ok: phone exited Remote SIM mode, got indication "Please Wait" on Comand and phone went into Sync mode. Almost immediately though I get on the phone "System Error" and just the option to press ok. I pressed ok and few seconds later the synchronization process ended, Remote SIM was activated again but phonebook was not loaded to COMAND. I repeated the same process over and over again, removed pairing and went over the whole pairing process from the beginning but still no luck. Unfortunately neither the phone or the COMAND would give any information on what the problem was.
    I checked for many hours on Nokia and Mercedes forums, on Google, etc. but still no luck. I found quite a few people facing the same problem mainly with N95 and E-series phones but no solution. Strange thing was that all were facing the problem from the very first time they tried to transfer their phone's contacts to COMAND while in my case in the past it was working and stopped working after upgrading my phones firmware.
    After hours of trial and error (removed recently installed phone applications, restored old phone backups, etc.) without luck I thought the problem would be the new firmware on my phone. But... I had no way to go back to the old firmware but even if I had I would cause the same issues that the new firmware solved again (so "rolling back" the firmware was not a real option). So I started going through every possible "core" phone setting that could have changed with the firmware upgrade to see what could be wrong and voila: if you go to the Connect->Sync menu on your phone you will see there a sync profile called PC Suite. Select it, click Options, Edit Profile and then, Connection. You will see that one option is Server Version. If selected Server Version is 1.2 underneath there is another option called Server ID. These two (Server Version and Server ID) are what cause the problem. You have the option to edit the PC Suite profile and set Server Version to 1.1 (then Server ID option disappears) and synchronization with COMAND will work. But as you might have side effects with PC Suite in this way, the ideal thing to do is to create a new sync profile, copy the settings from the PC Suite profile (you are prompted for this) and then, go and change this new profile so that Server version is 1.1. That was it (at least in my case) and I hope this will be helpful for others too. I also had Mail For Exchange installed on my mobile and removed it but I don't think this was the issue (will actually re-install MfE on my mobile now).
    Obviously, this Server Version 1.2 option did not exist on the old firmware of my phone so there was nothing to configure and all was working ok seamlessly but when it came out and set as the default by Nokia caused the incompatibility with Mercedes COMAND.
    Good Luck!

    Thanks for a thorough description of your problem and devised solution.
    I was getting very happy with your description of facts, for I recognized them all. However, in my case your solution did not work: I did change back to Server Version 1.1 of the synchronization profile and still get the "System Error" message.
    I have no doubts whatsoever that this happened with the 110.07.127 firmware upgrading.
    Do you have any other clue on how to proceed from here?
    JB

  • There is a problem communicating with the printer.

    I have a Lexmark Interpret S405. I am using a MBP laptop with WiFi, running 10.5.8. I have a cabled (non-wifi) Linsys router. I am using an Airport Express.
    I was finally able to get the WiFi light on the Lexmark to be static green after reinstalling the Lexmark WiFi setup and reconfiguring my Airport settings so that both the computer and printer see each other.
    In fact, I even updated the driver from Lexmark's Web site last night and I watched the WiFi light on the printer blink green indicating that the installation of the driver update was being communicated to the printer.
    However, when I print, it opens the print window and says first "Looking for S300-S400", then it says "Printer is now online". Then after about 10 seconds, I get this error: "There is a problem communicating with the printer. Make sure the printer is powered on and connected to the computer. Delete or hold the job and try again."
    I've exhausted Lexmark's technical databases and couldn't find the answer here.
    I've read that one possible solution was to delete all the printers from the "Print & Fax" system preferences window and re-add. That didn't work.
    Lexmark says for: The printer communicating on a network; however, the printer is not responsive. Possible causes could be:
    1. Your printer is associated with a network, router, or access point, but it is not your network.
    2. A software process is blocked by a system security firewall preventing network communication.
    3. You are logged into Virtual Private Network (VPN).
    4. You are connected to a network but have decided to switch to a USB connection.
    I don't have a VPN and have removed the USB cable, then restarted both printer and computer, and deleted printers in Sys Prefs, restarted, and still no solution.
    I can print directly via USB cable, but want to print wirelessly.
    Lexmark also says to enter my PIN (which I have pulled out from the print menu screen on the printer) in the System. That tells me a lot...
    Network settings on the print window on the printer also tell me Signal strength is 5 (excellent) and that I am on the network my airport is on.
    Message was edited by: Macman17

    I bet this is too late but...
    Are you trying to print through the airport express wirelessly or the built in wireless of the lexmark? If you want to use the airport express, there is no need to mess with the wireless printing on the lexmark at all. The airport express will be easy to set up, all the wireless setups through the printers are a pain.

  • How do I determine if the memory problems are with my imac and not the RAM?

    I've heard of some vague problems with intel imacs and their memory slots. I'm about to replace (for the 3rd time) RAM, and think I need to test further to see if the problem is with my imac and not the RAM. Right now I put back in the original 2-512 sticks that came with the imac, and the rember test is only showing 594mb (odd amt!) testing OK. But, in "about my mac" it will show as 1gb.
    Problems I've had with each set of RAM: occasional KP's, excessive spinning beachballs, sudden closing of apps (esp. if I have several apps running), won't fax usually (will hear a fax tone instead of a dial tone at the onset), disappearing documents section under my username.
    I bought this imac refurbed thru the apple store last fall: 2.16 C2D 20" imac
    Any ideas before I have to separate myself from my imac to send it in??

    Hi Toodles
    The pin strips on the new modules maybe a little thicker than your original modules, and it's going to take more force to seat them properly. If the new Memory Specifications are correct I would try them again. Slide them in untill they stop, then push real hard untill you feel them seat into place.
    I've never seen a report about an odd amount of ram shown. If reinstalling the ram modules does not solve your issue, and may be a indication that there is something wrong with one of the slots.
    Dennis
    17" iMac Intel Core Duo - 2GB Ram -   Mac OS X (10.4.10)   - Maxtor 300GB FireWire - Creative Inspire 2.1 - 2G Nano

  • I used migration to send photos form my Mac Book to my I Mac now i get an error message "iPhoto can not be opened because of a problem"  Check with the developer to make sure iPhoto works with this version of Max OSX.  You may need to install any availabl

    I used migration to send photos form my Mac Book to my I Mac now i get an error message "iPhoto can not be opened because of a problem"  Check with the developer to make sure iPhoto works with this version of Max OSX.  You may need to install any available updates or reinstall IPhoto.
    I tried installing Iphoto it said it was downloaded successfully. I still get the error messafe, and can not open any photos of program,  any suggestions?

    What version of iPhoto do you have on the Macbook and on the iMac? What systems are you running on the Macbook and on the iMac?
    Does the message only refer to "a problem" or does it specify what it is?
    Happy Holidays

  • How can I tell if my problem is with iPhoto or if the SD card ?

    I'm trying to import photos from an SD card, and when I attach my camera (or insert the SD card - I've tried both ways),  iPhoto shows me thumbnails of the pictures, and tells me they are already imported.  But when I disconnect my camera, the photos aren't in iPhoto.  If I click on "Import Photos" nothing happens, although I get a message telling me to wait until the photos have finished importing, if I try to close iPhoto. 
    Is there a way to tell if my problem is with iPhoto, my iMac, or the SD card?

    As a Test:
    Hold down the option (or alt) key and launch iPhoto. From the resulting menu select 'Create Library'
    Import a few pics into this new, blank library. Is the Problem repeated there?
    Post back with the result.

Maybe you are looking for

  • How to retrieve sharepoint list data and show it on excel-addin using C#

    Hi, we have a sharepoint list where all students are present. we wanted to get the data from the list and show it via excel addin (VSTO) (something like save,retrieve buutons) . we have some more business logic which need to be performed before the d

  • Store dynamic value in jsp

    hi, i have two page i pass value from one page to another and got it. now i want to store that dynamic value which i pass. i store it and got it my problem is that when page submit then value become null. i have three submit button. my code is <%@ pa

  • Overheating right hand side installed on graphic chip

    overheating right hand side  installed on graphic chip. Purchased in 3 month before And New brand 2nd laptop same  model. Already changed Motherboard, Fan with heating  and Ram. But problem still the continue.

  • Tolerance Types

    I have like 12 Tolerance types..can any one explain them for me.... <u>TKy -- Description</u> AN - -Amount for item without order reference AP-- Amount for item with order reference BR-- Percentage OPUn variance (IR before GR) BW -- Percentage OPUn v

  • A WebSite on a 3d-cube face

    Hi! I should realize a VirtueDesktop version web-oriented, but I have a problem: how do I show a website on a 3d-cube face? I don't need to show a simply image on a face of the cube, but a completely functional website, where the user can interact wi