WDS with Airport Express and 3COM Access Point

3CRWE454A72/WL 526
Runtime Code Version: 1.00 Dec 11 2003
Boot Code Version: V.2.25
Can this work?
Sorry if this question is not new
Regards,
Andre Peternell
Germany
PB G4   Mac OS X (10.4.8)  

- another Airport Express
- an Airport Extreme Base Station
- a Linksys WRT54G or WRT54GS
- a Belkin Belkin F5D7230-4 and F5D7231
- one specific model from SMC
- one specific model from Buffalo
- BT Voyager 2091
For wireless routers not on this short list - not possible.
In particular, it will not work with any WiFi routers from D-Link or Netgear.

Similar Messages

  • WDS with Airport express and Dual ethernet Airport base

    Can the airport express and dual ethernet airport base create a wds? I can't find the options on the airport base's software.

    coloradoapple, Welcome to the discussion area!
    The Dual Ethernet (snow) AirPort base station (ABS) does not support WDS.
    Only the AirPort Extreme base station (AEBS) and AirPort Express (AX) support WDS.

  • Can't find my Airplay - using Airport Express as an Access Point

    Hi,
    i've a slight problem with my airport express. i build a network with an easybox 803 router as base and an airport express as an access point in the next room. the airport led shows me that is all fine (green light). but i can't find the airplay service. I suspect that my macbook connects to the base and not to the access point.
    now i want to know: how can i config my mac or my airport express, so that i can find the airplay service
    best regards and thx for your help

    Solved.
    I had likely the same problem. It was solved by replacing the home router internal connections with a real switch.
    Many home routers will not properly multicast the required Airplay/Bonjour multicasts.  Netgear and D-Link for instance does not work, although some ASUS routers work if you turn off IGMP snooping and fiddle with the firewall, but only with some firmware, so it is very iffy.
    So, in my case, I connect Internet modem <-> router <-> switch <-> access points <-> devices
    Works without any problem. Also the wired devices connect to the switch.
    Do not connect any Airplay devices to the router!

  • Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points

    Hi Guys,
    I would like to go for "Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points 1300". I want the AP to broadcast only 1 SSID. The client find the SSID ->put in his user credential->Raudius athentication->assign him to an specific vlan based on his groupship.
    The problem here is that I don't have a AP controller but only configurable Aironet Access Points 1300. I can connect to the radius server, but I am not sure how to confirgure the AP's port, radio port, vlan and SSID.
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
    I go through some references:
    3.5  RADIUS-Based VLAN Access Control
    As discussed earlier, each SSID is mapped to a default VLAN-ID on the wired side. The IT administrator may wish to impose back end (such as RADIUS)-based VLAN access control using 802.1X or MAC address authentication mechanisms. For example, if the WLAN is set up such that all VLANs use 802.1X and similar encryption mechanisms for WLAN user access, then a user can "hop" from one VLAN to another by simply changing the SSID and successfully authenticating to the access point (using 802.1X). This may not be preferred if the WLAN user is confined to a particular VLAN.
    There are two different ways to implement RADIUS-based VLAN access control features:
    1. RADIUS-based SSID access control: Upon successful 802.1X or MAC address authentication, the RADIUS server passes back the allowed SSID list for the WLAN user to the access point or bridge. If the user used an SSID on the allowed SSID list, then the user is allowed to associate to the WLAN. Otherwise, the user is disassociated from the access point or bridge.
    2. RADIUS-based VLAN assignment: Upon successful 802.1X or MAC address authentication, the RADIUS server assigns the user to a predetermined VLAN-ID on the wired side. The SSID used for WLAN access doesn't matter because the user is always assigned to this predetermined VLAN-ID.
    extract from: Wireless Virtual LAN Deployment Guide
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00801444a1.html
    ==============================================================
    Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller Configuration Example
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
    ==============================================================
    Controller: Wireless Domain Services Configuration
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c951f.shtml
    Any help on this issue is appreicated.
    Thanks.

    I'm not sure if the Autonomous APs have the option for AAA Override.  On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
    I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override".  I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
    Hope this helps

  • WDS setup with Airport Express and other(non-Apple) wireless router

    Hi,
    I am trying to configure a wireless network with one airport express and one Planex Wireless access point. Can anyone please point me to the settings to be made for such a scenario? I can use either of them as the main WDS device, and have a (wired)router provided by the ISP in the network.(so total 3 devices : airport, planex a/p , ISP router)
    Thanks.

    I'm having the same problem, both with a Linksys WRVS4400Nv2, and a WRT54G. I've not put much effort into the WRT, but the WRVS was such a pain that I don't think I can get it to work at all.
    The WRT doesn't have a section on WDS, but I've read that it's supported anyways, and nothing needs to be enabled on it. Is there a good step-by-step available here or elsewhere that uses close to the same router and Airport Express units, on the latest Airport setup software?
    Basically, I'm trying to set this up for a guy in an ~8000 sq. foot house so he has wireless throughout it, and he wants itunes streaming from the AX. Has anyone done this?
    Message was edited by: manderso

  • Advised to get an "extender" to be able to stream netflix, etc. through new digital tv.  Apple store told me to buy Airport Express and set up WDS.  Upon reading about WDS it stated cannot set up WDS with Airport Express 802.11n,

    I was advised I needed an "extender" to stream Netflix, etc. through my newly purchased digital TV.  Apple store advised me to buy Airport Express and choose WDS setting.  When reading instructions on how to set up WDS it states cannot set up WDS with an 802.11n airport express, which is what they told me to purchase.  How do I set up this Airport Express to extend my internet signal from my modem & airport to be able to stream internet capability to my TV?

    I was advised I needed an "extender" to stream Netflix, etc. through my newly purchased digital TV.  Apple store advised me to buy Airport Express and choose WDS setting.  When reading instructions on how to set up WDS it states cannot set up WDS with an 802.11n airport express, which is what they told me to purchase.  How do I set up this Airport Express to extend my internet signal from my modem & airport to be able to stream internet capability to my TV?

  • Extending network with Airport Express and Airport Extreme (latest models) causes chaos on network

    Today I upgraded from my several year old Airport Extreme (3rd gen) and 2nd gen Airport Express to a new (what you'd buy on the shelf today) Airport Extreme and Airport Express.  All airports are updated with the latest firmware and I'm using windows 7 for configuration.
    The intention is to use the Airport Extreme as the main router, also serving wifi. And extend the network using the express. As such, the following has been done:
    The Airport Extreme is configured for automatic channel, and automatic radio mode. I tried to select 802.11n 5 ghz and 802.11 n 2.4 ghz only, but it won't take the changes. Additionally, it wont' accept me using only channel 6. Not sure why, but I digress. The airport extreme is not set to broadcast a separate name for the 5ghz network.
    The Airport Express is configured to use bridge mode, use an existing wireless network and is connected to my network on it's WAN port (the circle icon on the back) with ethernet. The password and wireless name used in configuration is the same as created initially on the Airport Extreme.
    Initially I did the configuration of both airports on my computer, connected by ethernet to ensure stable connectivity while I inputted settings. During this, they appeared to accept the changes fine. However, when I moved the airport express to it's destination (other side of my house), the entire network went crazy.
    Internet became slow, and often wouldn't load pages. This was on wired and wireless connections. When I attempted to administer the Airport in the Utility, they would not load, an error would occur. Also, at one point the Airport Extreme had renamed it self with a (2) at the end. Which was super odd. So far, the only solution has been to unplug the Airport Express and attempt to devise a solution.
    Anyone have any ideas? Of course, I will continue to tinker with this, but it seems realllly strange. The previous setup was also extended (granted, using wireless only, not ethernet > wireless) and worked fine, granted it was a smidge slow, but it worked.

    I wanted to add this.. I followed the guide here: http://support.apple.com/kb/HT4260 to extend using ethernet, and the above is the result.
    I just tried re configuring in OS X Mavericks and got the same, odd, result.

  • Need help with Airport Express and so on.

    Ok so my main problem before getting into what I need help with here is that our MacBooks and now my iPhone 6 plus isn't staying online. Keep getting booted off and then I either have to select the network again or it will eventually go back on. If anyone has a solution or so please feel free to answer that as well. I'm running on Roadrunner with a Netgear 600 wireless router and a motorola modem. Both of which I'll leave the link to below for a better look.
    My Main Question: So I'm looking at a new wireless router mainly and possibly a new modem. I know Apple products are trustworthy but how good is the Airport Express and other Airport products. Also what is the Maximum speed and Maximum data speed for the cheapest express station and if anyone knows the speeds of the other devices it would be greatly appreciated.

    DSL Router to Netgear 5-port Switch and I used the switch to connect to Airport Extreme, TV, Blue-Ray DVD player and DirecTV Receiver.
    The AirPort Extreme base station (AEBS) is a router so it will do what you need.
    You need to reconfigure your setup. Connect the WAN port of the AEBS to the DSL router. Then connect the Netgear switch to one of the LAN ports on the AEBS. The AEBS will properly share the connection.

  • How to extend wireless with airport express and time capsule

    So, I have a time capsule & because of the thick walls in my apartment, I can barely use my ipad and iphone at night in my bedroom! (my macbookPRO stays at 3 bars however!)
    I bought an airport express thinking I could plug it closer to or inside my bedroom to boost the signal - but it doesn't seem to work that way - any tips on how to set this up?
    TWO ADDITIONAL Qs:
    Does connecting directly to my time capsule (which i'm assuming i'd need another ethernet cable) help with the boost? (then negates the other great uses for the airport express it seems)
    Isn't there a way to do the boost with the express wirelessly? I'd really love to get wireless speakers, use airplay AND be able to use my devices just two rooms away ....   HELP!
    thanks so much (when did apple phone support start to be closed on Sundays?)
    cheers.

    Suggest that you check your setup again to make sure that the settings are correct on both the Time Capsule and AirPort Express.
    Open AirPort Utility, select the Time Capsule and click Manual Setup
    Click the Wireless tab below the row of icons
    Make sure that a check mark is entered next to "Allow this network to be extended".( If the box is not checked, the Time Capsule will not extend to the AirPort Express)
    Click Update to save your settings and close AirPort Utility
    Next, open AirPort Utility again, select the AirPort Express and click Manual Setup
    Click the Wireless tab
    Settings should look like this:
    Wireless Mode = Extend a wireless network
    Wireless Network Name = Same name as the Time Capsule network
    Check mark entered next to "Allow wireless clients"
    Wireless Security = Same setting as the Time Capsule
    Wireless Password = Same password as the Time Capsule network
    Confirm Password
    Update to save settings and close AirPort Utility
    Locate the AirPort Express approximately half way between the Time Capsule and area that needs more wireless coverage. You may need to experiment on placement to find the best compomise.
    Post back on your results.

  • Hi-fi separates with Airport Express and Airtunes

    Hi, please could you tell me whether it is possible to use a hi-fi separates system with airport express? it doesnt seem possible to me but i thought i would ask.
    regards
    ste bond

    Ah. Much clearer to this antipodian now
    If you have a look at page 15 of the Setup Guide for Airport Express, available at http://manuals.info.apple.com/en/AirPortExpressSetupGuide.pdf - it shows the connections it can be made to plug into.
    Every hi-fi system I've seen has stereo RCA jacks (red and white plugs) on the back for accepting auxiliary inputs. You'll just need to get the appropriate cable from your supplier of choice. If you system is more modern, using fibre optic cabling may be a better option (avoids ground loops, avoids multiple analog/digital conversions, etc).
    You can only use iTunes to send sound to the Airport Express, unless you get a third party application like AirFoil (from http://www.rogueamoeba.com/airfoil/ ), so technically "what I like" would need to be restricted to that which you had in iTunes, but basically, yes.

  • Airplay error with airport express and apple tv

    I receive this message "An unknown error (-15006) occurred while connecting to the AirPlay device" when trying to play audio from iTunes on Macbook Pro to my airport express and/or apple tv. Both airport express and apple tv work fine with my iphone and ipad as well as streaming video from itunes library to apple tv from the Macbook. I have tried the previously posted solutions, but nothing has worked yet.

    http://www.cultofmac.com/178460/the-real-reason-why-macs-before-2011-cant-use-ai rplay-mirroring-in-mountain-lion-feature/

  • Conflicts with Airport Express and Time Capsule

    I am using Airport Express and Time Capsule at the same time. Connection to the web is via a router. Very often I do have conflicts. How shall I connect the gadgets? At the moment I connect the router to Airport Express (network cable).
    Time machine back up doesn't work properly.
    Is there anybody able to help me?
    Regards

    What broadband type do you have?
    It can be impossible to plug a TC into the existing connection because the virgin media router has special setup or logins which are not revealed to end users.
    If it is a fibre connection for instance the TC may simply not work. They have issues with many fibre ISP putting the gateway address outside the subnet of the main public IP.. (don't worry if it is too technical .. it amounts to .. it don't work! )
    You may need to wait until Sat.
    Get in a big supply of home videos or something and try and starve off your addiction.

  • 3 powerline adaptors with airport express and extreme

    Hi all,
    I am currently using two airport express and 2 TP-LINK powerline adaptors to create a "roaming" network, however i would like to add another powerline adaptor and an airport extreme to my network.
    Modem -> Airport Extreme in the living room with an ethernet cable plugged into the powerline
    1st Airport Express plugged into the 2nd powerline adaptor
    3rd Airport Express plugged into the 3rd powerline adaptor
    so my question is will the above setup work? or do i need to connect another powerline adaptor into the main Airport Extreme making the whole network use a total of 4 powerline adaptors? however if only a total of 3 powerline adaptors are required, would the network be confused and render the whole network useless?

    To set up the 802.11n AirPort Extreme Base Station (AEBSn) as a bridge, either connect to the AEBSn's wireless network or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN port of the AEBSn, and then, using the AirPort Utility, make these settings:
    AirPort Utility > Select the AEBSn > Manual Setup > Internet > Internet Connection tab
    Connection Sharing: Off (Bridge Mode)
    Click Update to apply the new settings
    AirPort Express Base Station (AX) - iTunes Setup
    Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
    AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
    Wireless Mode: Join a wireless network
    Network Name: <existing AEBSn's wireless network>
    Wireless Security: <select the encryption type of the existing wireless network>
    Wireless Password: <enter the existing wireless network password>
    Verify Password: <re-enter the existing wireless network password>
    AirPort Utility > Select the AX > Manual Setup >Music
    Enable AirPlay (checked)
    iTunes Speaker Name: <enter desired speaker name>
    iTunes Speaker Password: (optional)
    Verify Password: (optional)
    Click Update to write the new settings to the AX

  • Is Printer HP Laserjet 1018 compatible with Airport Express and windows

    I am using HP Laserjet 1018 which is connected directly to the PC.
    As it is a USB printer but not a wifi one, can I connect it to Airport Express and will it be recognised ?
    Thank you for your answers.

    Hello TigerParis75,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    AirPort Utility 6.x: Use a USB printer on your Wi-Fi network
    http://support.apple.com/kb/PH5114
    Just make sure you have all the updated version of the drivers.
    Best of luck,
    Mario

  • Problem with Airport Express and HP PSC 1410

    Please I really need help. I just bought a HP PSC 1410 (all in one) and I connected on Airport Express and I can't print trought it. I tried to connect it by USB and it work perfectly. When you want to had the printer in printer utility you can find the right driver for the printer. Rendez-vous can find it but you can not install it...
    I tried many different way but it never worked.
    please help me ???

    I suggest you return the PSC1410 for refund, or for credit towards the purchase of another printer. This printer will not work when connected via an Airport Express. When you purchase your next printer, chose one found on the unofficial compatibility list at http://www.efelix.co.uk/tech/1013.html
    In general, all-in-one printers are poor choices for connecting via an Airport Express. Even if you do get them to work, you can only make use of their printing function.

Maybe you are looking for