Weak signal fail with 3.1

Anybody else notice a loss of weak signal pull in? On 9/1/09 it seems a new tower turned on and I suddenly had a couple of bars at my remote mountain house that I'd never had before, the signal stayed strong roaming around in my remote area very much better than before. then I updated and blammo no more signal, zilcho,nothing bummer.
anybody else notice anything like this? IPhone 3GS 32gb Anybody have any suggestions, similar experience?

bktonyc,
I noticed that my phone occasionally "freezes" during phone conversations (2 out of 5!) which requires the complete power-down of the phone. This never occurred under 3.0.1 firmware. I'm holding my breath to see what I'll discover next!
Apple, please give us some way to reload 3.0.1 firmware!!! I don't give a rat's behind about the new & improves MMS or other features that were supposedly rolled into this newest version of the FW. I can't even use this iPhone as a reliable telephone!!!
For what it's worth, I also notice that occasionally the signal strength decreases to near zero, and I can't access the internet or even place calls. This is when I know I'm in close proximity to a cell tower (I know, because my wife's phone has full signal strength). I wonder if this is somehow related to the rapid battery discharge, as the phone may be "hunting" for a signal (endlessly transmitting, and looking for a response from the cell tower).
Rob

Similar Messages

Concurrent requests failing with - emsg:was terminated by signal 11

Hi All,
we have cloned a test instance form production. Most of our concurrent requests are failing with the following error:
APPLLCSP Environment Variable set to :
Current NLS_LANG and NLS_NUMERIC_CHARACTERS Environment Variables are :
American_America.UTF8
stat_low = 8B
stat_high = 0
emsg:was terminated by signal 11
Start of log messages from FND_FILE
End of log messages from FND_FILE
Program was terminated by signal 11
Concurrent Manager encountered an error while running Oracle*Report for your concurrent request 23532851.
Review your concurrent request log and/or report output file for more detailed information.
Please note that the only requests which are getting successfully completed are the one which produces no output like "gather schema" or "Dashboard".
All the request's output is generated in PDF format on source.
System Information:
OS - Sun Solaris Sparc 64, Solaris 10
Apps - R12.1.1,
DB - 11.1.0.7.
Please help me in getting it resolved.

Hi;
please check below notes:
Arabic Bitmap Reports Complete in Error [ID 798213.1]
R12 XLAABACR Error XLA-95103 When Attempting to Validate Application Accounting Definitions [ID 472564.1]
T4A PDF PROCESS FAILING WITH SIGNAL 11 [ID 1078950.1]
Various Payroll and Legislative Reports Are Erroring With Signal 6 Or Signal 11 [ID 551042.1]
Regard
Helios

I get a weak signal with WIFI or 3G on, but a strong signal with EDGE.HELP

I get a weak signal with WIFI or 3G on, but a strong signal with EDGE. This doesn't make any sense! Help!

this happens to me, too. i get 1 bar of 3g but 4-5 when it switches to edge.
i also got this on my old blackjack ii and thought maybe it was just something having to do with that phone, but i guess not!

How to force Airport to join an AP with weaker signal?

I'm trying to figure out if there is a way to get the Airport card in my MBP to join an access point, with the same SSID as another access point, but that has a weaker signal?
Say there's 2 access points (A and B) and they both have the same SSID (eg. Wayport_Access). A is on channel 11 and B is on channel 1. A has the stronger signal. By default, and normally, you would want the airport card to associate with the access point with the best signal, A in this case. However, I'm in the situation that A is not functioning properly. So I want to join, B, even though it's farther away.
I've tried using iStumbler to force a join with the B access point on channel 1, but nothing happens. I stay on A as long as it's the stronger signal. If I move such that I get to a place where B is the stronger signal I can then get iStumbler to get the Airport card to associate with B on channel 1. If I then move back to my original location where A is the stronger signal I do stay associated with B, which is good. However, due to hotel positioning and such, it's not always convenient or even physically possible to move to a position where the B signal is stronger.
I thought I remembered an advanced setting somewhere that would allow me to set something about stronger/weaker signal setting but I cannot find it in Sys Prefs.
Any ideas?
-Rich

LarryHN wrote:
do you have the air port icon displayed in your top menu bar - if not add it in the system preferences ==> network ==> airport?
Yes.
Click on it and click join other network then sow networks and click on the one you want to force to - that should do it
Not if both Access Points have the SAME SSID, there's the catch. There's no mechanism through the Airport Menu or System Pref to join a different access point with the SAME SSID. That's why I was using iStumbler, because it will show ALL available access points, even the ones with the same SSID, based on which channel they are on. I want to associate with the access point that has the weaker signal, but has the same SSID as the access point that I'm already associated with. If IIRC there used to be an advanced setting about signal strength, but I can't find it anymore.
-Rich

IPhone 5 weak signal become iPhone being tempered with no serial number. Horrified!

I faced weak wifi signal problem with my new iPhone 5. Hence i went to the service provider, Singtel to check the problem and was told after they open up my iPhone that there was no serial no. inside the phone. As such, they were not able to help me cos mine was a tempered product.
But,
1. I received the new iphone from Singtel by renewing my contract. How would I know the phone was tempered.
2. I was not there when the phone was opened, as they took the phone into their backend room. How would I know if Singtel tempered it themselves?
The chance is low but who knows. Afterall, this is the same logic they gave me, since they say they don't hold responsibility for tempered phone as they won't be sure if I have tempered the phone even though the chance is low. Obviously, I would be real dumb to not expect they would open the device to check if I really wanted to cheat.. And for a corporate phone, it has to be a really desperate person to want to resort this.
3. If I had not observed the wifi signal weakness, I won't have even bothered to go to the service centre. In fact I was still holding on to my iPhone 4 and resisted to switch as all my data was there. I switched only when my singtel cut my iPhone 4 service and i had to activate my iPhone 5.
4. So the thing is, I would be cheated with a tempered product had I not have my weak wifi signal problem. I wonder how many other consumers are cheated.
5. Anyway, I though each device comes with an unique serial number. My iPhone 5 serial was registered in my phone when I activated it. Is it not proof that this is a genuine phone?
I am supposed to be a short changed customer to have to waste my time visiting Singtel for a phone problem and then being told that my phone has been tempered with and hence my warranty for the new phone is void.
I would really appreciate it greatly if someone could share with me how I should best resolve this. Thanks so much!
Best regards,

Thanks for your advice and taking the time to reply. :)
Actually, I thought so too that the serial number in my setting would identify my iPhone as a valid apple iPhone. However, the service provider who supply the phone with the plan do not recognise that. They told me that under their policy, if a phone has been tampered with, in this case no serial number inside the iPhone, ( amazingly the iPhone was supplied by them and who would thought of opening up the iPhone to check the components when you purchase it?) , they will not recognise the iPhone.
So In a nutshell, i went to the technical centre for help in my weak wifi signal problem for a new iphone and ended up being told that my phone which I just received in nov is a tempered iPhone....

Custom concurrent program failing with Signal 6 error

Custom concurrent program failing with the below error ,
stat_low = 6
stat_high = 0
emsg:was terminated by signal 6
Enter Password:
# An unexpected error has been detected by HotSpot Virtual
Machine:
# SIGSEGV (0xb) at pc=0xf608fd7e, pid=16054, tid=3417308016
# Java VM: Java HotSpot(TM) Server VM (1.4.2_14-b05 mixed mode)
# Problematic frame:
# C [libca.so.0+0x2dd7e] caupzsearch+0x1e
Help needed to debug this error.
Regards,

Please post details of application release, database version and OS.
Is the issue with one specific custom concurrent program? What is the type of this CP? Has this ever worked?
Please enable trace/debug as per (How To Trace a Concurrent Request And Generate TKPROF File (Doc ID 453527.1)) and see if more details are collected in the log then.
Thanks,
Hussein

Airport only connects with G5 door removed ... weak signal?

The Airport Extreme card in my G5 has trouble connecting to my wireless network when I move my tower away from my network base station ... it seems to be a weak signal that improves only if I remove the G5 case door. I reseated the the card and double-checked that the card wire was connected. Is the card going bad?

Hi Kool G4-
And, as my hero Homer would say, doh!
These folks might be able to help: MAC-PRO
Luck-
-DaddyPaycheck

I bought my iPhone 4 open line in Vancouver, Canada last week for use here in my home base in Bangkok, Thailand. But when I tried using my Thai sim, I get a very weak signal, if not a weak signal, then a no service status. What do I do?

I bought my iPhone 4 open line in Vancouver, Canada last week for use here in my home base in Bangkok, Thailand. But when I tried using my Thai sim, I get a very weak signal, if not a weak signal, then a no service status. I also have very weak wifi reception. What do I do?
I already tried the following:
a. Turned the phone off and then on.
b. Checked all wifi connections – no problem given that all our laptops and desktops can connect seamlessly.
c. I tried restoring the phone to original factory settings via itunes
d. Tried resetting the phone.
e. Tried different microsims from all networks
f. However, all methods failed given that the network reception is very weak and often reflects – “no service”. And with regards to the wifi reception It has difficulty in reading even the signal right in front of the wifi router.
I went to two Apple resellers here in Bangkok and requested that they please look at my Iphone and have it serviced. I was frustrated when they said that given that I bought my phone in Canada, they are not able to support me and should instead try to contact the Apple store in Canada.
I went to apple.ca website and went to the expresslane support and I was said to register and callback. Tried calling the 1800 number but given that I was in Thailand I had difficulty getting a connection.

1st sentence, 4th page of the iPhone warranty found here:
Apple may restrict service to the country where Apple or its
Authorized Distributors originally sold the hardware product.
From the Repair terms and conditions found here:
9. Availability of Service.
Apple may restrict service to the country where Apple or its authorized distributors originally sold the
hardware product, and to the countries listed in the table below. A list of authorized distributors is
available online at:
http://images.apple.com/legal/warranty/docs/iPhoneAuthorizedDistributors.pdf
If you do not believe that, then see these search results which confirm my statement.

E1200 - Had a weak signal and slow speed

Pros: Price, nice sleek shiny box, kind of worked when new. Good as a paperweight in a light breeze.
Cons: Not really a good doorstop - too light. Died at 35 days of ownership. Won't let me in to the web interface to make some changes. When working it had a weak signal and slow speed. Doesn't support access point mode like my old wireless router did.
Other Thoughts: Not the first time I'm had problems with Linksys/Cisco branded products but this is the last product I'll ever buy with the Linksys/Cisco name on it. Fact is ever since Cisco bought out Linksys, every product I've bought from them had failed/died within a few months. You'd think they would get this right by now but they haven't.

There are many reasons why you experience poor signal or connection. Well, there are few things you should keep in mind with regards to N routers:
1) For the best possible speeds, you need to be using WPA2-AES as your security mode. Any other security mode will see your speed/range capped.
2) Make sure the drivers for the Wireless Card for the computers should be updated as well..
3) The router by default uses a channel setting of auto, which means that it would keep switching channels depending on the interference. I’d recommend you set it to a fixed channel. Usually, 1, 3, 6 and 9 give you the best performance depending on your environment of course. I’d suggest you try different channels, observing each for a while, to see which gives you the best performance. You can follow the link here on how to change channels.
Second, all Linksys/Cisco can work as an Access Point. There are two (2) ways to cascade a Linksys router to another router:
1. LAN to LAN – Connecting one of the Ethernet ports (LAN ports) of the Linksys router (router A) to one of the Ethernet ports (LAN ports) of another router (router B).
This type of cascading requires the main and the secondary router to be on the same LAN IP segment to allow the computers and other devices to connect to both routers. This configuration is recommended if you want to share files and resources within the network.
2. LAN to WAN – Connecting one of the Ethernet ports (LAN ports) of router A to the Internet port (WAN port) of router B.
This type of cascading requires the main router and the secondary router to have different IP addresses. This connection makes it easier to identify which router the computers and other devices in the network are connected to since they will have different LAN IP segments. However, computers that are connected to router A will not be able to communicate with router B, and vice versa since they are two different networks.
Here is the link: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=785463d9ecaf4cac84aed245b08d615f_3733.xml&pid=80&r...

Jabber call to voice mail fails with fast busy over VPN

I have an issue that I ran into with CIPC phones over a VPN. If a CIPC phone called over a VPN and started ringing a phone the call would fail with fast busy at the time the call would be forwarded to voicemail. I found the issue was when remote the CIPC phone would negotiate the g.729 codec, when forwarded to a voicemail pilot over a SIP trunk set to g.711 the call would fail due to codec missmatch when no transcoders are present.
So now I am running into what I believe to be the same issue with Jabber, when on premise the calls to voice mail work just fine, but when remote they fail. I can directly call the voicemail pilot without error, but if calling a phone the call gets fast busy at the point we are forwarded to voicemail. Even though all my regions are set to talk to all other regions on G.711 and the voicemail SIP trunk is set to G.711, I believe with the new features in CUCM9 that a lower speed codec has been negotiated since the we are going over the VPN, or Jabber has done this as it knows it's over VPN (not sure). WIth CIPC I could go into the settings and turn off the Optimize for Bandwidth check box and the call would negotiate G.711. With Jabber I can't find anything that would tell my Jabber client to stay on G.711 and I can only imagine this is a codec missmatch as the following are true.
1. CIPC and Jabber share the same line
2. VPN established and CIPC optimised for low bandwidth un-checked
3. Over the same VPN the CIPC phone can leave a voicemail
4. Over the same VPN the Jabber client gets fast busy once forwarded to voicemail
5. Voicemail environment is Exchange-UM over SIP trunk
6. SIP trunk is assigned a Device Pool, that is assigned to a region that all other regions communicate G.711 to
7. On CIPC if optimised for low bandwidth is checked I get the exact same issue as I get with the Jabber client (fast busy when forwarded to voicemail)
Would anyone know what I can do in CUCM 9 to fix this issue, as said no issue when all devices are on premise. Wondering if there is a service parameter or a way to change the codec selection so the Jabber client attempts to always negotiate G.711. The correct answer would be to get some PVDM DSP resources and kick up a transcoder in my resource group, and that may be what I talk them into doing if I have no other options.

We have been getting the exact same thing for almost a year now... since switching to FiOS Digital Voice in May of last year! Every time I call in to report it they 'escalate' the issue but it never gets resolved. The problem seems to be in the initial connection. Most of the time it works fine but, several times a month, after I call to get messages and it starts to play the new message it goes dead and I get the busy signal. I get the same message when I call back: “I’m sorry – that account is in use at this time. Please try again later!” I have even called in with my cell phone and get the same message! I HAVE EVEN used the Internet to see if I could get my messages and, when I hit Play, I get a pop-up saying: “Your Voice Mail box is currently in being accessed; please try again later. If the problem continues, please contact our Customer Support Center at 1-888-553-1555. We apologize for any inconvenience.” This is obviously a software bug that Verizon has no clue on how to troubleshoot OR fix!!! I wonder how many people have the problem and just don’t bother reporting it because of the hassle? When it first started happening they destroyed my entire mailbox and I had to re-enter the complete mailbox setup again – 3 times!!! NEVER let them talk you into that!!! It’s their problem and they need to fix it!!!!!!! I wish I could go back to the ‘normal’ voicemail we originally had… they want hundred$ to switch back because I’d be breaking my #$@%^&* contract! Good luck if you have Verizon………

New router: cp1525nw wifi install fails with vague error message

Product: HP Laserjet Pro cp1525nw
OS: WIndows 8.1
Hardware: Asus laptop
Recently received new router from Verizon (FIOS), model FQG1100 BHR4 Router
Purchased printer in 2012.
Printer was working with old router; it won't communicate with new router.
Over four days I have repeatedly removed the printer from the laptop and tried reinstalling using the wifi method. The install instructions say to run the CD, choose wifi, connect the USB cable when prompted, configure, remove cable when prompted.
When I attach the USB cable the configuration starts, but it either times out ("taking too long") or fails with vague message about not finding the product. I am never prompted for an SSID.
I tried a USB install and that worked; so the USB cable is good.
Windows File & Print Sharing is enabled.
I've tried re-setting the printer to defaults, and ensured the wifi menu says "ON" for wifi.
I ran a wireless network test report:
PASS for wireless on, wireless working, and Security.
FAIL for Network Name (SSID) Found.
NOT RUN for: printer settings consistant with wireless router settings, No filtering, connected, signal strength, other networks detected.
Wireless netwrorks detected: 9
I note the router label does not statE "SSID", but says "ESSID".
I would appreciate any ideas for what to try.
Please post here or send message to [Personal Information Removed]
This question was solved.
View Solution.

Last night I finally got it to work. I removed the printer fully from the PC and rebooted. I turned off the printer. I ran a cable to the router (cable modem). I reset the router, which then assigned an IP address to the printer. I changed the security settings on the router to use WEP instead of WPA. I ran the HP printer setup program---and it finally presented me with the "provide SSID" screen. The program ran successully. I printed a test page. I changed the router secuirty back to WPA2. I printed another test page. I tried rebooting everything and printed again. I also tried removing the cable and then printing again---the printing failed.
In short, I needed to do two things: connect a cable and change the router temporarily to WEP for the install.
In my case, my printer is close enough to the router to run the cable. A little disappointing that the true wireless won't work, but I can print wirelessly from my laptop.
I've seen how a lot of people have had the same issue I had, and how HP is of no help in solving this issue. I'm convinced the printer has a flaw. I hope my posts will be of benefit to a few people having the same issue.

11gr2 RAC install on RHEL fails with "failed to create or upgrade olr"

New 11gr2 install on empty Red Hat Enterprise Linux 5.4 machine fails with "failed to create or upgrade olr"
Error during config steps. First script ran OK (orainstRoot.sh) on both nodes.
Second script failed on DB01, and I haven't run on DB02, as it's supposed to complete on DB01 first.
[root@RiskmgmtDB01 oraInventory]# cd /u01/app/11.2.0/grid
[root@RiskmgmtDB01 grid]# ./root.sh
Running Oracle 11g root.sh script...
The following environment variables are set as:
ORACLE_OWNER= oracle
ORACLE_HOME= /u01/app/11.2.0/grid
Enter the full pathname of the local bin directory: [usr/local/bin]:
Copying dbhome to /usr/local/bin ...
Copying oraenv to /usr/local/bin ...
Copying coraenv to /usr/local/bin ...
Creating /etc/oratab file...
Entries will be added to the /etc/oratab file as needed by
Database Configuration Assistant when a database is created
Finished running generic part of root.sh script.
Now product-specific root actions will be performed.
2010-11-12 10:35:13: Parsing the host name
2010-11-12 10:35:13: Checking for super user privileges
2010-11-12 10:35:13: User has super user privileges
Using configuration parameter file: /u01/app/11.2.0/grid/crs/install/crsconfig_params
Creating trace directory
PROTL-16: Internal Error
Command return code of 41 (10496) from command: /u01/app/11.2.0/grid/bin/ocrconfig -local -upgrade oracle oinstall
Failed to create or upgrade OLR
[root@RiskmgmtDB01 grid]#
Looking on the net, anyone who has hit this has had a problem with permissions, so as suggested I ran:
[root@RiskmgmtDB01 grid]# /usr/sbin/getenforce
Disabled
[root@RiskmgmtDB01 grid]# /usr/sbin/setenforce 0
/usr/sbin/setenforce: SELinux is disabled
[root@RiskmgmtDB01 grid]# /usr/sbin/getenforce
Disabled
As this is already set to disabled, I don't think it will help.
The two other threads similar to this are:
root.sh failed with signal 11 while installing 11gR2 grid infrastructure
root.sh script fail to run on OEL5.4
But neither works. I've raised a support request, but if anyone else has a bright idea ....
Thanks, Duncan

This document seems to apply: PROTL-16 Reported while Executing OCRCONFIG [ID 1123453.1]
It recommends running CVU, but that showed no issues.
So next step is the uninstall, as per: How to Proceed from Failed 11gR2 Grid Infrastructure (CRS) Installation [ID 942166.1]
However "$GRID_HOME/crs/install/rootcrs.pl -verbose -deconfig -force -lastnode" fails:
# /u01/app/11.2.0/grid/crs/install/rootcrs.pl -verbose -deconfig -force -lastnode
2010-11-15 17:11:21: Parsing the host name
2010-11-15 17:11:21: Checking for super user privileges
2010-11-15 17:11:21: User has super user privileges
Using configuration parameter file: /u01/app/11.2.0/grid/crs/install/crsconfig_params
Can't open /etc/oracle/scls_scr/node01/root/ohasdrun for write: No such file or directory at /u01/app/11.2.0/grid/crs/install/s_crsconfig_lib.pm line 1021.
So no further along yet ...

Io/26 and weak signals

I recently purchased an io/26 (using current drivers) and have been experiencing some pretty weak signals into GB, mostly when I'm using a mic (an EV 767) to record guitars and vocals. I believe I've got things set up correctly, but I'd like to be wrong...
I usually have to get the mic right up to the speaker or sing extremely close to the mic. The mic uses the xlr input on channel 1 or 2, with the switch on the mic/line setting as opposed to the guitar setting; phantom power is off. With these settings, I have to turn the gain up to about 80% to get a decent signal into GB. The driver software is pretty simple and doesn't allow me to adjust input levels. There is some "HDM" software (hardware direct monitoring) but I'm assuming this only affects sound routed back to the io for monitor speakers or headphones.
I'm hoping I'm just doing something stupid. I realize the ev767 is a vocal mic, but it should be a decent multi-purpose mic for my needs. One thing I am not able to do because the input is so weak is to place a mic far enough away from an amp (or a person) to get the sound of a room. Frustrating.
While I've been searching other threads here for similar issues, nothing seems directly relevant. Mostly, this is because the io/26 disables most of the software input settings that is a solution for usb mics, usb/midi input, etc.
Has anyone else come across this problem?
Thanks,
Rich

Well, here's a couple of pages I had bookmarked a while back:
http://www.gearslutz.com/board/low-end-theory/108916-alesis-io-26-anyone-seen-us ed-reviews-2.html
http://acapella.harmony-central.com/forums/showthread.php?t=1562285&page=24
I think most of the discussion was from back before their drivers were updated, which was the cause of a lot of problems.
Here's the latest Alesis Newsletter:
http://alesis.com/emails/nov08/newsletter.html?utmsource=MailingList&utm_medium=email&utm_content=poflynn%40nyc.rr.com&utmcampaign=Alesis-+NewsletterNov
Hopefully these can get you started. Oh, and here's the email of a tech guy at Alesis (Numark) who was very helpful. (I find the tech guys know a lot more than the salesmen).
[email protected]
(We have the same interface and the same mic. You don't by chance play a Taylor cutaway do you)?

703: Subdaemon connect to data store failed with error TT9999

All,
I'm getting the following error whilst trying to connect to a TimesTen DB:
connect "DSN=my_cachedb";
703: Subdaemon connect to data store failed with error TT9999
In the tterrors.log:
16:39:24.71 Warn: : 2568: 3596 ------------------: subdaemon process exited
16:39:24.71 Warn: : 2568: 3596 exited while connected to data store '/u01/ttdata/datastores/my_cachedb' shm 33554529 count=1
16:39:24.71 Warn: : 2568: daRecovery: subdaemon 3596, managing data store, failed: invalidate (failcode=202)
16:39:24.71 Warn: : 2568: Invalidating the data store (failcode 202, recovery for 3596)
16:39:24.72 Err : : 2568: TT14000: TimesTen daemon internal error: Could not send 'manage' request to subdaemon rc -2 err1 703 err2 9999
16:39:24.72 Warn: : 2568: 3619 Subdaemon reports creation failure
16:39:24.72 Err : : 2568: TT14000: TimesTen daemon internal error: Deleting 3619/0x1558650/'/u01/ttdata/datastores/my_cachedb' - from association table - not found
16:39:24.72 Err : : 2568: TT14004: TimesTen daemon creation failed: Could not del from dbByPid internal table
16:39:24.81 Warn: : 2568: child process 3596 terminated with signal 11
16:39:25.09 Err : : 2568: TT14000: TimesTen daemon internal error: daRecovery for 3619: No such data store '/u01/ttdata/datastores/my_cachedb'
I've checked and the datastore does exist and is owned by the timesten UNIX user.
ttversion:
TimesTen Release 11.2.2.2.0 (64 bit Linux/x86_64) (tt1122:53396) 2011-12-23T09:26:28Z
Instance admin: timesten
Instance home directory: /home/timesten/TimesTen/tt1122
Group owner: timesten
Daemon home directory: /home/timesten/TimesTen/tt1122/info
PL/SQL enabled.
Datastore definition from sys.odbc.ini:
[my_cachedb]
Driver=/home/timesten/TimesTen/tt1122/lib/libtten.so
DataStore=/u01/ttdata/datastores/my_cachedb
LogDir=/u01/ttdata/logs
PermSize=40
TempSize=32
DatabaseCharacterSet=AL32UTF8
OracleNetServiceName=testdb
Kernel parameters from sysctl -a:
kernel.shmmax = 68719476736
kernel.shmall = 4294967296
Memory / SWAP:
MemTotal: 2050784 kB
SWAP: /dev/mapper/VolGroup00-LogVol01 partition 4095992
I'm new to TimesTen and I'm planning on evaluationg it to see if it could solve an issue we're having. Any suggestions would be much appreciated.
Thanks,
Ian.

Hi Ian,
Can you please answer the following / provide the following information:
1. What are your kernel parameters relating to semaphores set to? Is anything else on the mahcine using significant numbers of semaphores?
2. Please provide the output of the following shell commands:
ls -ld /u01
ls -ld /u01/ttdata
ls -ld /u01/ttdata/datastores
ls -ld /u01/ttdata/logs
3. Please provide an excerpt of the detailed message log (ttmesg.log) between around 16:38 and 16:40 (i.e. from a little while before the problem until after the problem).
Thanks,
Chris

No signal or weak signal samsung

I have my appletv hooked up via hdmi to my samsung dlp hlr5667w tv and I keep getting a "no signal or weak signal" message. Why can't my tv find the Apple TV signal? I do not have any other splitters or devices hooked up and I have the same issue with different hdmi cables. When I unplug the. Plug the Apple TV into the power I get a green apple screen for a few seconds before the no signal message returns.

Welcome to the Apple community Mazino9.
How long is your HDMI cable.
Have you tried using another TV.
You may wish to try the following:
Press and hold the menu and the up button simultaneously on the remote for six seconds, the Apple TV should then begin to cycle through the various resolutions available to it. If you see a picture appear up on your screen, use the remote to scroll down to the OK option and select it.

Weak signal fail with 3.1

Similar Messages

Maybe you are looking for