Weak signal from Airport Express on extended network

I'm receiving only 2 bars from my Airport Express even with devices right next to it (see attached pics). I've reset the Airport Express and the extended network setup goes fine there's just a weak signal. If I take my devices to the modem router I get a full signal. Any ideas?
iPhone 5S
iPad Air 2
Cisco Linksys Dual band wireless N modem Gigabit router

The AirPort Express does work with virtually any wireless router for AirPlay or a remote printer.
Unfortunately, you must have missed the following clear statement in the product information for the AirPort Express regarding extending a network.
If you already have a wireless network in your home and want to extend its range, AirPort Express can help. Just place it in range of your primary base station — an AirPort Extreme, AirPort Time Capsule, or another AirPort Express
http://www.apple.com/airport-express/

Similar Messages

  • How to restore strength of signal from Airport Expresses on a network

    I have a newly developed problem with the signal strength from two Airport Expresses drawing a wireless signal from an Airport Extreme downstairs near the router and an IMac. This network has been functioning well for some time. Recently I noted that the signal strength upstairs (for I Pods etc) was weak where it had previously been strong. The Airport Utility program reports that these AExpresses have been properly set up and report no problems (My Airport utility version was 4.something, in spite of supposedly being automatically upgraded, and when I checked "upgrades" that brought the response that there were none, even though the current version is 5.5.2, and I then went and got that upgrade anyway).
    After fiddling with the upgraded Airport Utility, without knowing what I was doing, and possibly making the Airport Extreme reset itself, the strength of one of the Airport Expresses, (the one further away) increased almost to previous (normal?) levels, while the closer one stayed weak (the one Airport Utility calls "Base Station" even though, like the further Airport Express, it is an identical Airport Express wirelessly connected to the Airport Extreme downstairs). Both, incidentally are 8011n, if I have that right.
    Please forgive this incoherent post, but I am confused about how to trouble shoot a network like this, when something is not going right. I have read a number of the support articles as well as posts in this discussion group, and have learned a lot in general, but not specifically for this problem.
    Thanks Rick Ward

    Ok, thanks for clarifying your network requirements with the AXns.
    For both AXns to be successful in extending the AEBSn's wireless network they need to be within a 25+ dB SNR range of that AEBSn. SNR, or Signal to Noise Ratio, is the base station's Signal strength (in dBm) - Noise level (in dBm). Two primary reasons for low SNR values is Wi-Fi interference and obstacles (like walls/ceilings, etc.) that prevent a signal from passing through.
    You can easily calculate the SNR value by using a utility like iStumbler. Ideally, you would run iStumbler on a laptop and take signal & noise measurements at both the location of the AEBSn and at the desired locations of the AXns (with the AXns powered-off). If the SNRs are 25+ dB, then you should be get good performance with placing an AXn there to extend the AEBSn's wireless network. If not, then you won't.
    Also, remember, with the 802.11n AirPorts, think of the configuration of the extended network with the main router as the hub of a wheel and the extending routers as spokes on that wheel. You cannot extend the network in a serial fashion (main to relay to remote) in this configuration.

  • Use airport express to extend network from linksys wrt54g

    Hello all, I'm having no luck here, and hope you can help me. I am running a MacBook Pro, 2.16 GHz, Intel Core 2 Duo, 3 Gigs ram, OS X 10.6.8.I am at work, trying to use a newly purchased AirPort Express to extend the signal from the back office, which has a Linksys WRT54G router. I updated the router's firmware to 1.02.8, build 001, dated 8.5.09. I have tried numerous times to configure the AE using AirPort Utility, and always wind up with an error message, "An error occurred while updating the configuration. Make sure your Apple Wi-Fi base station is plugged in and in range of your computer or connected via Ethernet and try again. (-6753)" During the configuration process, I am asked what I want to do with AE, I have tried both "create a new wireless network," and "I want AE to join my current network," with no success. Any comments will be appreciated.

    The Linksys WRT54G and WRT54GS (through version 4 only for both models) were said to be compatible with Apple's WDS settings.
    Perhaps this article may offer some clues, but it is doubtful that you will be able to make this work with the particular version of Linksys router that you have.
    http://hints.macworld.com/article.php?story=2006060516541633

  • Trying to use Airport Express to extend network created by Actiontec M1424WR (FiOS)

    I would like to use two Airport Expresses to extend my home network which is created with my Actiontec M1424WR.  My ISP is Verizon FiOS.  I previously had TimeWarner and used one of my Expresses to create the WiFi and the second Express to extend it.  Now that I have a modem/router provided by Verizon, I'd like to utilize both Airports as extenders.  I have a two story house and the signal is "fair" upstairs.  I would like to use my Roku player to access my home library via Plex. My problem(s):
    I used a hard reset to restore my Expresses to the default settings because my Airport Utility could not find them and my old network is not active anymore.  After the reset I was able to find them but I kept getting an "unexpected error occurred try again later" message.  After this message my Macbook OS X 10.8.5 could not connect to the internet anymore.  I had to go to System Preferences ---> Network ---> Assist Me.. ---> Assistant ---> and then found my network and reconnected.  So my Macbook is connected again but my Airport Expresses sit unused..
    My Network:
    Modem/Router ->     1. PC
                                   2. PC #2
                                   3. Xbox
                                   4. D-link 5 port gigabit switch -> a. Directv  b. xbox #2  c. xbox #3   d. THIS IS WHERE I WANT MY AIRPORT                                       
    I would like one Airport, connected via ethernet and towards the back of the house, extending my network and the other, connected via wifi and upstairs, also extending my network.
    If anyone has time on their hands to help me with my problem I would greatly appreciate it.
    Thank you,
    Mike

    I followed Kappy's advice and connected one AEX to my modem/router using a 50ft ethernet cable, creating a new network.   I connect my second AEX wirelessly to the first, extending the network.  The first AEX was placed towards the back of the house and the 2nd AEX was placed upstairs.  I was able to stream netflix on two devices upstairs while streaming a movie using plex from one pc downstairs to a roku player upstairs without any buffering at all.  All three were in HD and my brother was playing multiplayer on his xbox (wired).  It works! Thanks Kappy!

  • Airport Express to extend network - WEP security issue

    I have an existing Time Capsule based wireless network (set to WEP Transitional Security). I just bought Airport Express with the intent to extend my network. The TC is set to allow the network to be extended. I also set up the Airport Express to extend an existing network - however, I am not sure what security protocol to set since WEP Transitional is not an option. I chose WEP 128 but it resulted in the Airport Express hanging when it tries to update and restart. If I chose a WPA protocol it does update and restarts fine. iTunes recognizes this as a speaker. However, I'm not sure if this is a correct setting. Also the Airport Express does not show up in the list of wireless networks to connect (which I assume is the way it should work).
    I went through the discussion board but could not find any solution. Any help would be greatly appreciated

    Welcome to the discussion area, Katan!
    If I chose a WPA protocol it does update and restarts fine. iTunes recognizes this as a speaker. However, I'm not sure if this is a correct setting
    That is the correct setting.
    Also the Airport Express does not show up in the list of wireless networks to connect (which I assume is the way it should work).
    That's correct. It's extending your wireless network, so you'll only see that wireless network as a choice to join from each computer or device.
    Your computer will automatically connect to the device with the strongest signal, which is almost always also be the closest device unless there are major obstructions involved in the signal path.
    Post back if you are interested in checking to see which device your computer is actually connected to at any given time.

  • Using airport express to extend network/stream music

    Hi,
    I just bought an airport express to extend my network throughout my house and stream music to my stereo system in my living room. My time capsule, which is connected to the DSL modem and is the base station, is in one far end of the house, while the airport express is at the other end. It has greatly improved the range of my network and when using my macbook in the front room, it gets full bars, however, the when using airtunes to stream music with iTunes 9 and OS 10.6, the music will cut in and out randomly and I occasionally get unknown error -15000 when trying to connect.
    I played around with the airport express channels (any channel other than 10 will receive an unknown error -15000 automatically,) adjusted the firewall, and adjusted Netbarrier X, my third party security software. I found information in this article:
    http://support.apple.com/kb/TA21538?viewlocale=en_US
    The only thing that works is moving the airport express close to my computer to remove the physical barriers. It plays perfectly then. Is it possible to buy a second airport express and plug it in halfway between my stereo and time capsule to boost the signal to the airport express plugged into my stereo? Will this solve the problem of the music stream cutting in and out every 10-20 seconds?

    Mad Cow wrote:
    I checked and my signal is -87 and noise is -95.
    At the risk of being the bearer of bad news, that's a rather poor signal value. Here is a description of what different ranges of signal-to-noise mean:
    http://discussions.apple.com/thread.jspa?messageID=10329543&start=1
    In the other post, you mentioned interference from other electronics. Could physical barriers be causing interference also?
    Barriers won't cause interference, but they can reduce signal transmission. How far apart are the two units, how many walls are in between, and of what material are those walls made?
    If this is the case, can I add a second airport express between my base station and stereo-attached airport express to boost the signal?
    In theory something like that might work, but I'm not sure that an AirPort Express can act as a "relay" station between a "main" station and a "remote" station. It might require an AirPort Extreme. Perhaps someone else can comment on that possibility.
    Can you relocate your Time Capsule to an different phone outlet? Can you use longer cables between the wall and the modem and/or between the modem and the Time Capsule to move the Time Capsule to the other side of the room to be nearer to your AirPort Express? Can you use a longer audio cable between your AirPort Express and your sound system?
    You may be able to use a pair of Power-Line units
    (http://computer.howstuffworks.com/power-network.htm) to connect your AirPort Express to your Time Capsule via Ethernet.

  • Airport Express to Extend Network Range

    Hi everyone, hope somebody can help me out with this.
    I have an airport express which I had been using as a wireless router. It worked fine although the range wasn't all that good, so I got a new Linksys wireless router and installed it in the living room. I was planning on using the airport express to extend the Linksys range by plugging the airport express to the power in my bedroom.
    Anybody know how I can make that work without having to plug the ethernet cable into the airport express??
    Thanx

    david_neg, Welcome to the discussion area!
    I agree with Niel. You might be able to get it to work if the router is a Linksys WRT54G or WRT54GS (not latest versions v5). If you are using something else the chances of working are near zero.

  • My devices not automatically switching between Airport Extreme and Airport Express in extended network

    I have setup an extended network in my home using an Airport Extreme and an Airport Express. The Extreme is connected directly to the FiOS modem and the Express is being used as the extender. The nework is setup fine, but my devices (MBA, iPhone, iPad) are not switching base stations when the signal becomes poor on the one it's connected to. For example, I am upstairs with my MBA and a great signal as I am connected to the Express. When I move downstairs to where the Extreme is setup, the Wi-Fi connection becomes poor even though I am litterally sitting next to the Extreme. To force it to connect to the Extreme, I need to shutoff the Wi-Fi on the MBA and turn back on. At this point, the MBA will connect to the Extreme with a excellent signal.
    Any thoughts on why the MBA is not automatically switching?
    Thanks for the help!
    Brian

    The first troubleshooting step for any kind of network "issue" is a complete power cycle of the network. This gives everything a "fresh start" with new connections.
    Power off the entire network.....all devices....in any order you want
    Wait a minute or two
    Start the modem/router first, and let it run a full minute
    Start the AirPort Extreme next and let it run a full minute
    Keep starting devices one at a time about a minute apart until the entire network is back up
    Check the network again with the MBA and report on your results
    Do not worry about the iPhone and iPad....they are pretty much hopeless as far as automatically switching from one access point to another....but the MBA should if it is working correctly.

  • Can't get wireless signal from Airport Express

    I recently bought an Airport Extreme and Airport Express. The base station is in my office which is separate from my house so I bought an antenna from Macwireless.com. I'm able to play iTunes thru the Express perfectly but there's no wireless signal coming from the Express to connect to the internet. Does anyone have any idea what I can do to fix this?
    After reading some other posts I found that my old wireless system wasn't acting up at all. It was Mac OS X 10.4.10. causing the disconnections to the internet. Great. Just great.

    I'm able to play iTunes thru the Express perfectly but there's no wireless signal coming from the Express to connect to the internet. Does anyone have any idea what I can do to fix this?
    If you have the Express and Extreme in a single Network there will be only one available network name to join. In that single wireless network the Express can be set up to extend range of network by using WDS, or simply as a wireless client that can print or use iTunes. If you check the Airport Utility help files it will give full documentation on how to set up either type of wireless network.

  • Using Old AirPort Express to Extend Network Coverage

    I have an old AirPort Express sitting literally a yard away from my Mac mini. My Network Connection doesn't reach the room where my Mac is very well, so I thought this would help... but the network still only sometimes shows up on my devices. (2010 Mac mini, iPhone 4 CDMA, Original iPad WiFi)
    I set it up from scratch, (it used to be near the router to connect to a printer, but I replaced it with a brand new AirPort Extreme and decided the Express might help back with my Mac) and I set it up to extend the network connection. It shows up, and I get better signal when I'm connected, but my Mac is the only device that can connect to it all the time. Both my iPhone and my iPad drop the connection frequently.
    Any ideas what could be the problem and how to fix it?

    The correct location for a device that is "extending" a wireless signal is a point that is about half the distance from the "main" router to the general area that needs more wireless coverage.
    My guess is that you have the AirPort Express located too far away from the main router. The Express can only extend the quality of signal that it receives, so it is very important that it can get a strong signal from the main router.
    Try to minimize obstructions in the signal path as much as possible. To give you an example, a typical sheetrock wall in a home will absorb 15-20% of the wireless signal on average. A ceiling will absorb much more since it is much thicker.
    After the signal must pass through 3-4 walls, or a ceiling and a few walls, there won't be much of the signal left.

  • Using airport express to extend network of 2tb time capsule.

    Is it possible to use my old airport express using 802.11g to extend the network of my 2tb time capsule using 802.11ac protocol?  If so, how?

    You will need to use one of the 802.11n versions of the AirPort Express....either the model A1264 or A1392....if you want to wirelessly extend the signal from the Time Capsule.
    The older 802.11b/g Express does not have the capability to do what you want.

  • Time Capsule is Slower and has a Weaker Signal than Airport Express

    I have been using an airport express (g) without any problems for several years and usually get full signal strength throughout my small manhattan apartment. I recently decided to upgrade to a Time Capsule. I set it up and found that signal was weak and data transfer was slow. After rebooting it and installing the firmware update, things did not get any better. I took my laptop and TC to the Apple Store and they set it up again for me. In the Apple store, I found that the connection was strong and that the data was extremely fast. When I brought the unit back, I was only able to connect with a few bars (4) and found the data transfers to be extremely slow, practically unusable. I'm not sure what to do, I think there's something interfering with the signal but then again, I put the TC right where the old AirPort Express used to deliver a strong (full) signal.
    Any suggestions?

    I set the Time Capsule to channel 11 from automatic. Since then, the Time Capsule has been working perfectly. I love it.

  • IPod Touch has Weak Signal on Airport Express

    I have the following:
    1. Airport Express with 802.11n Wi-Fi (Version 7.3.2)
    2. iPod Touch running Software Update 2.2
    3. iPhone 3G 16GB running Software Update 2.2
    My iPhone can connect to the Airport Express with no problems at all. The signal is very strong and the connection is excellent. However, the signal on the iPod Touch is very, very weak and drops out all the time. In fact, I can be standing right next to the Airport Express and the signal can be very weak. This does not seem right. What do I have to do to ensure that my iPod Touch as the same signal strength as my iPhone? Thanks

    That definitely helped a bit. I guess I get one more bar than I got before. However, it is still significantly weaker than the iPhone and is still a bit inconsistent. That was a very good tip though, thanks

  • Airport Express to extend network and stream music at the same time?

    Hi. I have an Airport Extreme base station (primary wireless access point) and an Airport Express. Currently I connect my Hi-Fi to the Airport Express and stream music from iTunes, but I would like to also make use of its Ethernet port to connect other wired devices to my network. Is this possible; can it be used for both simultaneously? I've tried various configurations but not managed to achieve this.

    Welcome to the discussions!
    If you have an AirPort Extreme(n) and AirPort Express(n), the ethernet port for the Express will be active if you "Enable ethernet client" during setup using AirPort Utility.
    It sounds like you have either the "g" version of the Extreme or Express or both. Both devices must be "n" capable to use this option. If you don't see an option on the Wireless setup page of the Express to "Enable ethernet client", you have a "g" Express and this function is not available with your device.

  • Using airport express to extend network via ethernet socket

    I have a wireless router set up which feeds my mac and tv (via a wired ethernet connection).  I have also a pc which doesn't have wifi capability.
    Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?  I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
    Thanks

    Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?
    Yes. But, it is the AirPort Express that would "pick up the wifi". Then, you would connect an Ethernet cable from the AirPort Express to the PC.
    Configure the AirPort Express to "Join a wireless network" and click the option to "Enable Ethernet clients" during the setup to activate the Ethernet port on the device.
    I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
    There is a good chance that your printer will work connected this way, but you won't really know until you try.

Maybe you are looking for