Web Auth page not working on WLC
I have a WLC 4402 and I upgraded the s/w from 4.1 to 4.2.176 since I did the web auth on my Guest wlan does not work. I can connect to the wireless ok and when I type in a web address I should get the web auth page but I just get "This page cannot be displayed". However if i type in the ip address of the WLC in the addrsss bar I get the web auth page and it work fine form then on. The web auth page worked fine on ver 4.1. Any ideas?
I opened a TAC case this morning on this same problem, and my solution is what is listed above (config network secureweb cipher-option sslv2 enable)
Basically, SSLv2 is disabled in 4.2. The Default is now SSLv3.
Depending on your Internet settings, if IE is configured to use SSLv2, the webpage will not work.
So in internet explorer, tools, internet options, advanced, There will be a checkbox next to Use SSLv2. (Even if Use SSLv3 is enabled, you still have the https issue).
Basically, my issues was that a select few users could not Web authenticate and a select few admins couldn't HTTPS manage the GUI. Turns out in all cases, the computers that were all able to work, did not have SSLv2 enabled.
By enabling SSLv2, all affected users now work (I think).
Similar Messages
-
I'm using 4404 controllers and 1131 access points. Im on version 6.0.188.0
My Web Auth Page stoped working. I switched our webauth page back to the built in one to test weather or not it was my custome webauth was giving me the problem. It still didn't work. I switched an AP over to my second controller and used the built in webauth and it worked.
I tired restarting my first 4404 controller help.
I doubt it but maybe it has something to do with another problem i posted about. https://supportforums.cisco.com/message/3042441#3042441
does anyone have any ideas on what to do?I might have found a clue. I went under the security tab and clicked LDAP. I notice that server state was set to disable on controller 1. I looked at controller 2 and it was enable.
I made controller 1 enabled then pressed apply. I tried to login again and it didn't work. I went back and hit the apply button again and a message box poped up. It said "failed to set retransmit Timeout."
after I clicked ok (the only option) it set server state was disabled again. -
Firefox does not redirect users to web auth page
I have a client that uses web auth for the guest wireless. When a users opens up FF, it does not automatically redirect them to the web auth page. However, IE and Chrome work fine. If you copy and paste the redirection page into FF, it will go to the page then. The only two possible solutions I have found are to either enable web auth proxy or regenerate the WLC self-signed cert.
Anyone have any other ideas?
TIA,
DanI've been trying to figure out a very similar issue where Firefox wouldn't open the guest webpage (the connection was interrupted) and finally found it was caused by opening Yahoo as my startup page. I change it to Google, for example, and it comes up everytime now. When set to Yahoo I could clear my cache and it would work once but then wouldn't work again. If I load Yahoo as the startup page in IE it works everytime. Very strange.
Here's what the debug looks like:
*webauthRedirect: Jul 23 20:59:33.793: xx:xx:xx:xx:xx:xx- received connection
*webauthRedirect: Jul 23 20:59:33.794: xx:xx:xx:xx:xx:xx- received connection
*webauthRedirect: Jul 23 20:59:33.795: xx:xx:xx:xx:xx:xx- received request
*webauthRedirect: Jul 23 20:59:33.803: xx:xx:xx:xx:xx:xx- received connection
*webauthRedirect: Jul 23 20:59:33.803: xx:xx:xx:xx:xx:xx- received request
*webauthRedirect: Jul 23 20:59:33.806: xx:xx:xx:xx:xx:xx- received connection
*webauthRedirect: Jul 23 20:59:33.807: xx:xx:xx:xx:xx:xx- received request
*webauthRedirect: Jul 23 20:59:33.810: xx:xx:xx:xx:xx:xx- received connection -
Content query web part is not working after chaning the DNS entry
Hi all,
We have a content query web part in the sharepoint site but it is not working after changing the DNS Entry for the web site ipaddress from one server to other . But it is working fine on the server, if we try to access the site from other system content
quey server its not working fine and its giving error message as bellow.
Unable to display this Web Part. To troubleshoot the problem, open this Web page in a Microsoft SharePoint Foundation-compatible HTML editor such as Microsoft SharePoint Designer. If the problem persists, contact your Web server administrator.
Can anyone help me to fix this issue please.I have custom XSLT . But it is working fine before changing the dns entry as soon as we change the DNS entry the content quey web part is not working. I tried to delete the content query web part and add it once again to the page, As soon as content query
web part is added to the page the fallowing error message is displayed.
Unable to display this Web Part. To troubleshoot the problem, open this Web page in a Microsoft SharePoint Foundation-compatible HTML editor such as Microsoft SharePoint Designer. If the problem persists, contact your Web server administrator.
Can anyone help me to fix this issue please. -
Having trouble with custom web auth page on 4404
Hi all
I am having trouble with a custom web auth page on my controller, we have edited the original file, but when we click login it goes to page cannot be displayed and it doesnt redirect to the page I want, however when I close the window and reopen it has already authenticated me.
Has anyone got a copy of some working html code I can use ?
cheersThere is sample Web Authentication bundle avaiable for download from cisco.com. if you go to the software download page and go to Wireless->Standalone Controllers->4404 you should see a link for Wireless Lan Web Authentication Bundle.
Its the same bundle whether you have a WiSM, 4404 or 2100 -
Can you have separate web auth pages for each SSID?
Sent from Cisco Technical Support iPhone AppHi,
If you are running WLC software 4.2 and above then u can do this on per WLAN basis.. here is the link which tells on how to do it..
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008067489f.shtml#A1
Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
Regards
Surendra -
Apache bridge & Basic Auth does not work
The WebLogic newsgroups are not the appropriate place to file product defect
reports.
I suggest that you file a bug report with our support organization. Be sure
to include a complete test case. They will also need information from
you -- please review our external support procedures:
http://www.beasys.com/support/index.html
Thanks,
Michael
Michael Girdley
Product Manager, WebLogic Server & Express
BEA Systems Inc
Jaroslav Mechacek <[email protected]> wrote in message
news:[email protected]..
>
I tried mod_wl with apache 1.3.12 ( mod_ssl / openssl ) ,
but the basic auth does not work.
When apache starts it complains that mod_lw uses plain apache api
Tue May 16 17:29:54 2000] [warn] Loaded DSO libexec/mod_wl.so uses plain
Apache 1.3 API, this module might crash under EAPI! (please recompile it
with -DEAPI)
When I request protected page, apache returns both
HTTP/1.1 200 OK , HTTP/1.1 401 Unauthorized
what apache / ssl configurations are known to work ?
Escape character is '^]'.
GET /file/index.html HTTP1.0
HTTP/1.1 200 OK
Date: Tue, 16 May 2000 14:47:01 GMT
Server: Apache/1.3.12 (Unix) mod_ssl/2.6.4 OpenSSL/0.9.5a
HTTP/1.1 401 Unauthorized xxx:
www-authenticate: Basic realm="WebLogic Server"
content-length: 23
content-type: text/html
connection: Close
No credentials supplied -
We have url-directed login page for web authentication.
Why does the Cisco page flashed, in a bit of a sec, before it goes ahead to the directed url.
Unfortunately, some customers are not happy with this.
Can that Cisco page be totally eliminated?no... the client doesn't get the full-blown cisco web-auth page. just at the Title bar of the Window, the Cisco Title bar appears very swiftly and directed right away to the supposed external web authentication page.
the code used and tested with were 4.1.171, 4.2.185, 5.2.157. and the behavior is the same for all code. it will flash that Cisco title bar and then directed right away to the external web authentication page.
nope, we're not trying to do something special. just the customer noticed it and somehow is not happy with it.
what could be the best acceptable explanation we can provide our customer for this very small yet customer-annoying instance. is there a Cisco document that we can show the customer regarding this behavior?
Thanks! -
Does anyone have a good resource to create custom web auth pages? I've modified the bundles from Cisco's website, but I am a terrible web designer. Just curious if anyone knows of a program to make these modifications easy for someone who doesn't have this skill set.
I use Microsoft Expressions, but I don't know if you call that drag and drop, You have a split window so you can see the code along with the browser. This way you can actually type on the browser preview and it will generate the code and vice versa. Here are some others, but might not be free:
http://www.ultraedit.com/support/tutorials_power_tips/ultraedit/integrated_html_preview.html
http://www.coffeecup.com/html-editor/
http://liveditor.com/index.php
Thanks,
Scott
*****Help out other by using the rating system and marking answered questions as "Answered"***** -
WSUS not working completely, no MMC connect, all web services are not working
Hello all,
I have a problem not sure what causing it or what is the source of it as I am not into WSUS that much...
THe status is as follows:
I have 1 server 2008 sp2 RTM x64, I had WSUS 3.0 SP2 on it since a while, it was working fine until a week ago, when I started receiving the below messages in the event viewer
I have spent too much time trying to trace or troubleshoot this issue, but all I got was to check the registry and check permissions on the temp folder and other folders, I have done complete removal with the database for the old WSUS and reinstalled it
again but I got the same problem
Nothing strange and no problems happened on the server perior to this issue, it just happened...
Any help will be appreciated
Regards
============== MSG 1 ==============
Log Name: Application
Source: Windows Server Update Services
Date: 9/21/2011 1:52:54 PM
Event ID: 7053
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: APP-SVR.DOMAIN.local
Description:
The WSUS administration console has encountered an unexpected error. This may be a transient error; try restarting the administration console. If this error persists,
Try removing the persisted preferences for the console by deleting the wsus file under %appdata%\Microsoft\MMC\.
System.InvalidOperationException -- Client found response content type of 'text/html; charset=utf-8', but expected 'text/xml'.
The request failed with the error message:
<html>
<head>
<title>Security Exception</title>
<style>
body {font-family:"Verdana";font-weight:normal;font-size: .7em;color:black;}
p {font-family:"Verdana";font-weight:normal;color:black;margin-top: -5px}
b {font-family:"Verdana";font-weight:bold;color:black;margin-top: -5px}
H1 { font-family:"Verdana";font-weight:normal;font-size:18pt;color:red }
H2 { font-family:"Verdana";font-weight:normal;font-size:14pt;color:maroon }
pre {font-family:"Lucida Console";font-size: .9em}
.marker {font-weight: bold; color: black;text-decoration: none;}
.version {color: gray;}
.error {margin-bottom: 10px;}
.expandable { text-decoration:underline; font-weight:bold; color:navy; cursor:hand; }
</style>
</head>
<body bgcolor="white">
<span><H1>Server Error in '/ApiRemoting30' Application.<hr width=100% size=1 color=silver></H1>
<h2> <i>Security Exception</i> </h2></span>
<font face="Arial, Helvetica, Geneva, SunSans-Regular, sans-serif ">
<b> Description: </b>The application attempted to perform an operation not allowed by the security policy. To grant this application the required permission please contact
your system administrator or change the application's trust level in the configuration file.
<br><br>
<b> Exception Details: </b>System.Security.SecurityException: That assembly does not allow partially trusted callers.<br><br>
<b>Source Error:</b> <br><br>
<table width=100% bgcolor="#ffffcc">
<tr>
<td>
<code>
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.</code>
</td>
</tr>
</table>
<br>
<b>Stack Trace:</b> <br><br>
<table width=100% bgcolor="#ffffcc">
<tr>
<td>
<code><pre>
[SecurityException: That assembly does not allow partially trusted callers.]
ASP.global_asax..ctor() +0
</pre></code>
</td>
</tr>
</table>
<br>
<hr width=100% size=1 color=silver>
<b>Version Information:</b> Microsoft .NET Framework Version:2.0.50727.4214; ASP.NET Version:2.0.50727.4209
</font>
</body>
</html>
<!--
[SecurityException]: That assembly does not allow partially trusted callers.
at ASP.global_asax..ctor()
[TargetInvocationException]: Exception has been thrown by the target of an invocation.
at System.RuntimeTypeHandle.CreateInstance(RuntimeType type, Boolean publicOnly, Boolean noCheck, Boolean& canBeCached, RuntimeMethodHandle& ctor, Boolean& bNeedSecurityCheck)
at System.RuntimeType.CreateInstanceSlow(Boolean publicOnly, Boolean fillCache)
at System.RuntimeType.CreateInstanceImpl(Boolean publicOnly, Boolean skipVisibilityChecks, Boolean fillCache)
at System.Activator.CreateInstance(Type type, Boolean nonPublic)
at System.RuntimeType.CreateInstanceImpl(BindingFlags bindingAttr, Binder binder, Object[] args, CultureInfo culture, Object[] activationAttributes)
at System.Web.HttpApplicationFactory.GetSpecialApplicationInstance(IntPtr appContext, HttpContext context)
at System.Web.Hosting.PipelineRuntime.InitializeApplication(IntPtr appContext)
[HttpException]: Exception has been thrown by the target of an invocation.
at System.Web.HttpRuntime.FirstRequestInit(HttpContext context)
at System.Web.HttpRuntime.EnsureFirstRequestInit(HttpContext context)
at System.Web.HttpRuntime.ProcessRequestNotificationPrivate(IIS7WorkerRequest wr, HttpContext context)
-->
Source
Microsoft.UpdateServices.Administration
Stack Trace:
at Microsoft.UpdateServices.Administration.AdminProxy.CreateUpdateServer(Object[] args)
at Microsoft.UpdateServices.Administration.AdminProxy.GetUpdateServer()
at Microsoft.UpdateServices.UI.AdminApiAccess.AdminApiTools.GetUpdateServer()
at Microsoft.UpdateServices.UI.SnapIn.Wizards.OOBE.OOBEWizard.get_AdminApiTools()
at Microsoft.UpdateServices.UI.SnapIn.Wizards.OOBE.OOBEWizard.get_ServerState()
at Microsoft.UpdateServices.UI.SnapIn.Wizards.OOBE.OOBEWizard.SetNavigationItemEnabledStates()
at Microsoft.UpdateServices.UI.SnapIn.Wizards.OOBE.OOBEWizard.OOBEWizardInitialize()
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Windows Server Update Services" />
<EventID Qualifiers="0">7053</EventID>
<Level>2</Level>
<Task>0</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-09-21T10:52:54.000Z" />
<EventRecordID>884368</EventRecordID>
<Channel>Application</Channel>
<Computer>APP-SVR.DOMAIN.local</Computer>
<Security />
</System>
<EventData>
<Data>The WSUS administration console has encountered an unexpected error. This may be a transient error; try restarting the administration console. If this error persists,
Try removing the persisted preferences for the console by deleting the wsus file under %appdata%\Microsoft\MMC\.
System.InvalidOperationException -- Client found response content type of 'text/html; charset=utf-8', but expected 'text/xml'.
The request failed with the error message:
<html>
<head>
<title>Security Exception</title>
<style>
body {font-family:"Verdana";font-weight:normal;font-size: .7em;color:black;}
p {font-family:"Verdana";font-weight:normal;color:black;margin-top: -5px}
b {font-family:"Verdana";font-weight:bold;color:black;margin-top: -5px}
H1 { font-family:"Verdana";font-weight:normal;font-size:18pt;color:red }
H2 { font-family:"Verdana";font-weight:normal;font-size:14pt;color:maroon }
pre {font-family:"Lucida Console";font-size: .9em}
.marker {font-weight: bold; color: black;text-decoration: none;}
.version {color: gray;}
.error {margin-bottom: 10px;}
.expandable { text-decoration:underline; font-weight:bold; color:navy; cursor:hand; }
</style>
</head>
<body bgcolor="white">
<span><H1>Server Error in '/ApiRemoting30' Application.<hr width=100% size=1 color=silver></H1>
<h2> <i>Security Exception</i> </h2></span>
<font face="Arial, Helvetica, Geneva, SunSans-Regular, sans-serif ">
<b> Description: </b>The application attempted to perform an operation not allowed by the security policy. To grant this application the required permission
please contact your system administrator or change the application's trust level in the configuration file.
<br><br>
<b> Exception Details: </b>System.Security.SecurityException: That assembly does not allow partially trusted callers.<br><br>
<b>Source Error:</b> <br><br>
<table width=100% bgcolor="#ffffcc">
<tr>
<td>
<code>
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.</code>
</td>
</tr>
</table>
<br>
<b>Stack Trace:</b> <br><br>
<table width=100% bgcolor="#ffffcc">
<tr>
<td>
<code><pre>
[SecurityException: That assembly does not allow partially trusted callers.]
ASP.global_asax..ctor() +0
</pre></code>
</td>
</tr>
</table>
<br>
<hr width=100% size=1 color=silver>
<b>Version Information:</b> Microsoft .NET Framework Version:2.0.50727.4214; ASP.NET Version:2.0.50727.4209
</font>
</body>
</html>
<!--
[SecurityException]: That assembly does not allow partially trusted callers.
at ASP.global_asax..ctor()
[TargetInvocationException]: Exception has been thrown by the target of an invocation.
at System.RuntimeTypeHandle.CreateInstance(RuntimeType type, Boolean publicOnly, Boolean noCheck, Boolean& canBeCached, RuntimeMethodHandle& ctor, Boolean& bNeedSecurityCheck)
at System.RuntimeType.CreateInstanceSlow(Boolean publicOnly, Boolean fillCache)
at System.RuntimeType.CreateInstanceImpl(Boolean publicOnly, Boolean skipVisibilityChecks, Boolean fillCache)
at System.Activator.CreateInstance(Type type, Boolean nonPublic)
at System.RuntimeType.CreateInstanceImpl(BindingFlags bindingAttr, Binder binder, Object[] args, CultureInfo culture, Object[] activationAttributes)
at System.Web.HttpApplicationFactory.GetSpecialApplicationInstance(IntPtr appContext, HttpContext context)
at System.Web.Hosting.PipelineRuntime.InitializeApplication(IntPtr appContext)
[HttpException]: Exception has been thrown by the target of an invocation.
at System.Web.HttpRuntime.FirstRequestInit(HttpContext context)
at System.Web.HttpRuntime.EnsureFirstRequestInit(HttpContext context)
at System.Web.HttpRuntime.ProcessRequestNotificationPrivate(IIS7WorkerRequest wr, HttpContext context)
-->
Source
Microsoft.UpdateServices.Administration
Stack Trace:
at Microsoft.UpdateServices.Administration.AdminProxy.CreateUpdateServer(Object[] args)
at Microsoft.UpdateServices.Administration.AdminProxy.GetUpdateServer()
at Microsoft.UpdateServices.UI.AdminApiAccess.AdminApiTools.GetUpdateServer()
at Microsoft.UpdateServices.UI.SnapIn.Wizards.OOBE.OOBEWizard.get_AdminApiTools()
at Microsoft.UpdateServices.UI.SnapIn.Wizards.OOBE.OOBEWizard.get_ServerState()
at Microsoft.UpdateServices.UI.SnapIn.Wizards.OOBE.OOBEWizard.SetNavigationItemEnabledStates()
at Microsoft.UpdateServices.UI.SnapIn.Wizards.OOBE.OOBEWizard.OOBEWizardInitialize()</Data>
</EventData>
</Event>
============== MSG 2 ==============
Log Name: Application
Source: Windows Server Update Services
Date: 9/21/2011 1:53:01 PM
Event ID: 13051
Task Category: 6
Level: Warning
Keywords: Classic
User: N/A
Computer: APP-SVR.DOMAIN.local
Description:
No client computers have ever contacted the server.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Windows Server Update Services" />
<EventID Qualifiers="0">13051</EventID>
<Level>3</Level>
<Task>6</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-09-21T10:53:01.000Z" />
<EventRecordID>884373</EventRecordID>
<Channel>Application</Channel>
<Computer>APP-SVR.DOMAIN.local</Computer>
<Security />
</System>
<EventData>
<Data>No client computers have ever contacted the server.</Data>
</EventData>
</Event>
============== MSG 3 ==============
Log Name: Application
Source: Windows Server Update Services
Date: 9/21/2011 1:53:01 PM
Event ID: 12002
Task Category: 9
Level: Error
Keywords: Classic
User: N/A
Computer: APP-SVR.DOMAIN.local
Description:
The Reporting Web Service is not working.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Windows Server Update Services" />
<EventID Qualifiers="0">12002</EventID>
<Level>2</Level>
<Task>9</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-09-21T10:53:01.000Z" />
<EventRecordID>884374</EventRecordID>
<Channel>Application</Channel>
<Computer>APP-SVR.DOMAIN.local</Computer>
<Security />
</System>
<EventData>
<Data>The Reporting Web Service is not working.</Data>
</EventData>
</Event>
============== MSG 4 ==============
Log Name: Application
Source: Windows Server Update Services
Date: 9/21/2011 1:53:01 PM
Event ID: 12012
Task Category: 9
Level: Error
Keywords: Classic
User: N/A
Computer: APP-SVR.DOMAIN.local
Description:
The API Remoting Web Service is not working.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Windows Server Update Services" />
<EventID Qualifiers="0">12012</EventID>
<Level>2</Level>
<Task>9</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-09-21T10:53:01.000Z" />
<EventRecordID>884375</EventRecordID>
<Channel>Application</Channel>
<Computer>APP-SVR.DOMAIN.local</Computer>
<Security />
</System>
<EventData>
<Data>The API Remoting Web Service is not working.</Data>
</EventData>
</Event>
============== MSG 5 ==============
Log Name: Application
Source: Windows Server Update Services
Date: 9/21/2011 1:53:01 PM
Event ID: 12032
Task Category: 9
Level: Error
Keywords: Classic
User: N/A
Computer: APP-SVR.DOMAIN.local
Description:
The Server Synchronization Web Service is not working.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Windows Server Update Services" />
<EventID Qualifiers="0">12032</EventID>
<Level>2</Level>
<Task>9</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-09-21T10:53:01.000Z" />
<EventRecordID>884376</EventRecordID>
<Channel>Application</Channel>
<Computer>APP-SVR.DOMAIN.local</Computer>
<Security />
</System>
<EventData>
<Data>The Server Synchronization Web Service is not working.</Data>
</EventData>
</Event>
============== MSG 6 ==============
Log Name: Application
Source: Windows Server Update Services
Date: 9/21/2011 1:53:01 PM
Event ID: 12022
Task Category: 9
Level: Error
Keywords: Classic
User: N/A
Computer: APP-SVR.DOMAIN.local
Description:
The Client Web Service is not working.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Windows Server Update Services" />
<EventID Qualifiers="0">12022</EventID>
<Level>2</Level>
<Task>9</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-09-21T10:53:01.000Z" />
<EventRecordID>884377</EventRecordID>
<Channel>Application</Channel>
<Computer>APP-SVR.DOMAIN.local</Computer>
<Security />
</System>
<EventData>
<Data>The Client Web Service is not working.</Data>
</EventData>
</Event>
============== MSG 7 ==============
Log Name: Application
Source: Windows Server Update Services
Date: 9/21/2011 1:53:01 PM
Event ID: 12042
Task Category: 9
Level: Error
Keywords: Classic
User: N/A
Computer: APP-SVR.DOMAIN.local
Description:
The SimpleAuth Web Service is not working.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Windows Server Update Services" />
<EventID Qualifiers="0">12042</EventID>
<Level>2</Level>
<Task>9</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-09-21T10:53:01.000Z" />
<EventRecordID>884378</EventRecordID>
<Channel>Application</Channel>
<Computer>APP-SVR.DOMAIN.local</Computer>
<Security />
</System>
<EventData>
<Data>The SimpleAuth Web Service is not working.</Data>
</EventData>
</Event>
============== MSG 8 ==============
Log Name: Application
Source: Windows Server Update Services
Date: 9/21/2011 1:53:01 PM
Event ID: 12052
Task Category: 9
Level: Error
Keywords: Classic
User: N/A
Computer: APP-SVR.DOMAIN.local
Description:
The DSS Authentication Web Service is not working.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Windows Server Update Services" />
<EventID Qualifiers="0">12052</EventID>
<Level>2</Level>
<Task>9</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-09-21T10:53:01.000Z" />
<EventRecordID>884379</EventRecordID>
<Channel>Application</Channel>
<Computer>APP-SVR.DOAMIN.local</Computer>
<Security />
</System>
<EventData>
<Data>The DSS Authentication Web Service is not working.</Data>
</EventData>
</Event>
============== MSG 9 ==============
Log Name: Application
Source: ASP.NET 2.0.50727.0
Date: 9/21/2011 1:53:09 PM
Event ID: 1314
Task Category: Web Event
Level: Information
Keywords: Classic
User: N/A
Computer: APP-SVR.DOMAIN.local
Description:
Event code: 4010
Event message: An unhandled security exception has occurred.
Event time: 9/21/2011 1:53:09 PM
Event time (UTC): 9/21/2011 10:53:09 AM
Event ID: 11b96ca285fa46d2a05d38e2e9b168af
Event sequence: 1
Event occurrence: 1
Event detail code: 0
Application information:
Application domain: /LM/W3SVC/715372307/ROOT/ApiRemoting30-7-129610759889193820
Trust level: High
Application Virtual Path: /ApiRemoting30
Application Path: C:\Program Files\Update Services\WebServices\ApiRemoting30\
Machine name: APP-SVR
Process information:
Process ID: 8332
Process name: w3wp.exe
Account name: NT AUTHORITY\NETWORK SERVICE
Request information:
Request URL:
http://app-svr:8530/ApiRemoting30/WebService.asmx
Request path: /ApiRemoting30/WebService.asmx
User host address: 192.168.5.22
User:
Is authenticated: False
Authentication Type:
Thread account name: NT AUTHORITY\NETWORK SERVICE
Custom event details:
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="ASP.NET 2.0.50727.0" />
<EventID Qualifiers="16384">1314</EventID>
<Level>4</Level>
<Task>3</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2011-09-21T10:53:09.000Z" />
<EventRecordID>884380</EventRecordID>
<Channel>Application</Channel>
<Computer>APP-SVR.DOMAIN.local</Computer>
<Security />
</System>
<EventData>
<Data>4010</Data>
<Data>An unhandled security exception has occurred.</Data>
<Data>9/21/2011 1:53:09 PM</Data>
<Data>9/21/2011 10:53:09 AM</Data>
<Data>11b96ca285fa46d2a05d38e2e9b168af</Data>
<Data>1</Data>
<Data>1</Data>
<Data>0</Data>
<Data>/LM/W3SVC/715372307/ROOT/ApiRemoting30-7-129610759889193820</Data>
<Data>High</Data>
<Data>/ApiRemoting30</Data>
<Data>C:\Program Files\Update Services\WebServices\ApiRemoting30\</Data>
<Data>APP-SVR</Data>
<Data>
</Data>
<Data>8332</Data>
<Data>w3wp.exe</Data>
<Data>NT AUTHORITY\NETWORK SERVICE</Data>
<Data>http://app-svr:8530/ApiRemoting30/WebService.asmx</Data>
<Data>/ApiRemoting30/WebService.asmx</Data>
<Data>192.168.5.22</Data>
<Data>
</Data>
<Data>False</Data>
<Data>
</Data>
<Data>NT AUTHORITY\NETWORK SERVICE</Data>
</EventData>
</Event>
Saleh RamadanSo, in reality, this issue has nothing at all to do with "it was working; now it is not", because you've destroyed all of the evidence that would exist in a "was working; now is not" scenario. What we really have here is a NEW installation that has failed.
So, from the perspective of a NEW installation that is not working...
Are there any other roles, features, services, or applications installed on this server?
Did you install the Web Server Role exactly as described in the documentation?
Did you install the WSUS Role exactly as described in the documentation?
Were there any other roles, features, services, or applications installed onto this server
after your original (working) installation of WSUS?
Lawrence Garvin, M.S., MCITP:EA, MCDBA, MCSA
Principal/CTO, Onsite Technology Solutions, Houston, Texas
Microsoft MVP - Software Distribution (2005-2011)
My MVP Profile: http://mvp.support.microsoft.com/profile/Lawrence.Garvin
My Blog: http://onsitechsolutions.spaces.live.com
Oh, well, I have red and followed the documentation exactly step-by-step on the technet library, and I can guarantee you nothing went wrong because this is not my first installation for it
When I told you about the old damaged installation and the new installation which is also failed and showed me the same symptoms as the old one, I was sure that nothing wrong with the WSUS itself, but rather it is something wrong with the environment
Answering to your above questions, the answer for all is that: that server is only used for WSUS, nothing more
Anyway, I have managed to restore the service thanks to your previous reply where you point to the CONFIG folder inside the NET framework folder, I checked the files in there, some were changed to the date I think has stopped the service, so I repaired the
NET framework 2, and restarted
It is working fine now and syncing with the update server
Saleh Ramadan -
Help, web cam is not working properly with win vista
Hii.. my web cam is not working properly with win vista..even if the icon appears bt it does nt start.. its
lenovo easy capture 2.5...so if u cud suggest me anything...
Moderator note; subject editedre-install drivers and try again. ( also easy capture )
-
12002 The Reporting Web Service is not working.
Hi :)
I have WSUS on Windows Server 2012 std. with Internal Database. Today I've installed 7 updates from patch tuesday and after restart I've got
error 12002 The Reporting Web Service is not working
I can see now that updatet clients can not report their status anymore :(
What's up ? Any suggestion ?
Best regards
NenadHi,
I would start by verifying that the /ReportingWebService resource is properly configured in IIS.
Correct configurations can be found in the WSUS Technical Reference Guide: IIS
Settings for WSUS 3.0 SP2 Web Services.
Also,Under ReportingWebService
Made sure all were set to disabled except for Anonymous Authentication
Anonymous Authentication Enabled
ASP .NET Impersonation Disabled
Basic Authentication Disabled
Forms Authentication Disabled
Windows Authentication Disabled
Regards,
Clarence
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback here.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. -
My integrated web cam is not working
I Am using hp pavilion p001tx laptop. My web cam is not working
It shows a warning
No web cam detected. Try to plugging in a webcam into your computer now. If you are using an integrated camera, Make sure that it is turned on.
Help me please.
My laptop serial number is [Personal Information Removed]Check if the drivers are installed or not.
Try to update the camera drivers and restart the system.
You can also go to device manager setting and see if the webcam is disabled or not.
If everything fails try system resore or run OS recovery. -
Nokia 701 web browser is not working
i have nokia 701. My phone web browser is not
working. Net is working in other browsers like
opera and uc browser. it's a big problem for me i
can't watch online videos and i can't access to google or any other site.. I also delete the cache folder in C drive. But still browser is not working.plz help me to solve this
problem...same here also. happened after i updated social. now cant browse or check for updates
-
HP Compaq web cam is not working
I have Hp Compaq Notebook 620. The devices have 2MP Web Cam but the Web Cam is not working. When i try to make it on, its shows error
"No webcam detected. HP Webcam will now Close"
Please suggest the solution of the problem.Hello Manishshakya,
I see that you are having problems with the webcam on your computer. The unit you have is a HP commercial unit.
I would suggest posting your problem in the HP Commercial Forum as well. There are more users with the computer you have on this board and it is specific to your computer.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓
Maybe you are looking for
-
How do I Get my library back on I tunes? I had to replace my hard drive.
I had to replace the hard drive of my macbook. Now when I open itunes, it is completely empty! is there anyway to get my music back or atleast the music I purchased from itunes? I can access my account it shows record of my purchases, but my library
-
Texts cuts off when I open a pdf document
I bought an ebook and whenever I open it in Adobe Reader the text on the right side is partially cut off. I thought it was a page size thing, but that didn't work at all. I've opened it in other formats so I know nothing is wrong with the file. I
-
Storing Column-Name into variable? Possible?
Hello from germany I got stuck with following: How is it possible to store the name of a column into a variable or is it possible to put an index "on" a column? The reason for this: I need to fill and check a complete column! Thanks for Your help! Be
-
Formula to filtering one field with another
Post Author: MWinn CA Forum: Formula I need to pull information from fields based on the contents of another field. For example, I want to use the SBCODE.SCDDS2 field in one location in the report, but it will only return the correct information if S
-
Hi, We are working on Classic Scenario. When the user tries to raise a limit order shopping cart, the storage location is not saved in the Shopping Cart and hence not reflected in the PO in R/3. The plant and storage location in user profile are defa