Web Interface of Cisco Prime 2.1 not working

Excuse me!
I install the trial version cisco prime 2.1 (OVA) on ESXi server
I can ping cisco prime but web interface of cisco prime not worinking
prime/admin# ncs status
Health Monitor Server is running.
Ftp Server is running
Database server is running
Tftp Server is running
Matlab Server is running
NMS Server is running.
Plug and Play Gateway is running.
SAM Daemon is running ...
DA Daemon is running ...
Syslog Daemon is running ...

Services running fine..
check it with other Browser , Supported browser are below::
–   Google Chrome 31 or later.
–   Microsoft Internet Explorer 8.0 or 9.0 with Google Chrome Frame plugin (users logging in to the simplified Lobby Ambassador interface do not need the plugin).
–   Mozilla Firefox ESR 24.
–   Mozilla Firefox 24, 25 or 26.
If above does not help , reboot the server once and check the issue again.
Thanks-
Afroz
***Ratings Encourages Contributors ****

Similar Messages

Web interface on Cisco Prime Infrastructure express not coming up

Trying to get Cisco Prime Infrastructure express installed. The installation completes without any error but when I try to run show NCS or attempt to start stop the service get the following output
usdayt-cis-002/admin# show application status NCS
% Application NCS is not installed
usdayt-cis-002/admin# ncs start
sh: /opt/CSCOlumos/bin/wcsadmin.sh: No such file or directory
here's the output from show inventory
usdayt-cis-002/admin# show inventory
NAME: "Cisco-VM chassis", DESCR: "Cisco-VM chassis"
PID: Cisco-VM-SPID , VID: V01 , SN: 1GP9SNNE5HJ
Total RAM Memory: 16304916 kB
CPU Core Count: 8
CPU 0: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 1: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 2: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 3: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 4: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 5: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 6: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 7: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
Hard Disk Count(*): 1
Disk 0: Device Name: /dev/sda
Disk 0: Capacity: 314.50 GB
Disk 0: Geometry: 255 heads 63 sectors/track 38244 cylinders
NIC Count: 1
NIC 0: Device Name: eth0
NIC 0: HW Address: 00:50:56:AF:76:34
NIC 0: Driver Descr: e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
(*) Hard Disk Count may be Logical.
usdayt-cis-002/admin# show disks
disk: 1% used (184324 of 44628400)
temp. space 2% used (35792 of 1967952)
Internal filesystems:
all internal filesystems have sufficient free space
any idea what could be the issue here?

OK, that's the correct one. Can you verify the checksum of the file? It should be:
91dc6ebc446c1c9c000c69af4be93102
If that's OK, I would delete the VM and try installing the ova once more.
Other than that, I'd suggest calling the TAC if it's a supported installation (i.e. not an evaluation copy).

Web Interface of Cisco Prime Infrastructure Not Working

Hi All,
I installed the trial version of Cisco Prime Infrastructure 1.2 on ESXi server.
It installed propersly and and i am able to ping it and also ssh into it.
But when I try to access it via web interface, it does not work.
I am provided with a login screen but after putting my credentials the page goes blank.
There also an error on the page "Error occured while fetching Meatdata for Slider Panel" and there is a advertisemnt to download Google chrome Framework.
When i do "NCS status" in CLI i see that every service is running.
Does anyone know how to solve this.
All your help is highly appreciated.

Google Chrome Frame isnt supported anymore, using Google Chrome doesnt work with all features and forget about Firefox. Up until this morning I had it working on IE11 but some update caused me to have this problem again. Cisco needs to get this fixed. I use several applications from Cisco and they still can't figure out a way to have them all work on a single browser.

Cisco Prime Soft Appliance not saving changes to syslog.conf

Greetings,
I'm having an issue with the syslog.conf file on a Cisco Prime LMS 4.2.4 soft appliance with a Solaris base. My workplace uses local4 as the logging facility for its network devices, and according to a discussion I found on this site, I need to add the line:
local4.info /var/log/syslog_info
I have attempted this several times; we're approaching at least 5 attempts today. I have attached text files created from putty logs where I've attempted to make the necessary change. I appreciate any assistance the community can provide.
Regards,
Rob

Hi, Afroz,
I really appreciate your assistance, but I'm afraid my hopes have been dashed. The syslog.conf reverted to its original configuration. I will go through my steps to be sure that I understood your suggestion properly.
I edited the syslog.conf to put all messages from local4 in /opt/CSCOpx/conf/syslog-entries.txt. Then, I exited the shell to the console, issued the 'write mem' command, and closed the session. Upon my reconnection, I found that my changes to the syslog.conf were not saved.
Did I make the correct edits in the correct places? Another question, is this bug present in the versions of Prime LMS running Linux and/or Windows, or does it only exist in the soft appliance running Solaris?
Regards,
Rob
Edit:
I'm reading the "Installation and Migration of Cisco Prime" PDF, and it gives me the impression that Cisco Prime is only supported as Windows, Solaris, and soft appliance installations. Is that correct? If it is correct, then installation of Cisco Prime LMS is not supported on other Linux distros such as Ubuntu Server, CentOS, Fedora, etc.?
My thanks.

Privileged Exec password works for telnet but not web interface on Cisco AP 1242

I recently configured a Cisco AP 1242, software version 12.4, via the web interface using the default Cisco credentials. At that time I setup an administrator account with read/write access and changed the Cisco to a read only access. Now went I attempt to login to the web interface it won't accept the administrator password. It will except the administrator password in a telnet session however. So via the telnet session I setup another user with privileged exec level access and that wont work on the web interface either. The Login box keeps coming back requesting a password. Strangely enough, I can login to the web Interface using admin username, with the Cisco password; but I can't do anything, and I also can't view everything.
I've tried the following:
I've turned on SSH and created a certificate in the AP, but the login box continues to pop on the https://url.
I've attempted to setup a user with a non-encrypted password, but have been unsuccessful.
I've tried a different browser - login box continues to pop.
I've made sure the web interface is activated in the AP
I've tried a differnet computer
I've tried disabling password-encryption service
Reset the enable password
I've successfully setup other 1240 APs but must have done something wrong on this one. Anyone know what I'm missing? Thanks.
Solution: I was missing "ip http authentication local" in my config.

Solution: I was missing "ip http authentication local" in my config.

Cisco Prime Collaboration Deployment - Not able to mount NFS

Hi everybody,
We are trying to add an ESXi server to the PCD, but we are unable to succeed due to an error while mounting the NFS unit.
We get the following message:
"Failed to mount Cisco Prime Collaboration Deployments export as NFS store to the ESXi Host"
In the PCD we obtain the followings logs I attach the file.
We are using a VMware vSphere Enterprise Edition
The ESXi, has the VMkernel port map to a different subnet that the management subnet.
VMkernel: 10.11.202.75
VMmanagement: 10.11.200.75
To Add the ESXi host we are attacking the 10.11.200.75. Someone knows if the VMkernel must be in the same subnet for the NFS to mount?
2014-11-07 14:17:26,711 WARN [pool-1-thread-18] validation.ESXiValidation.isDSinESXiHost - Datastore PCD_NFS is NOT connected to ESXi Host 10.11.200.75
2014-11-07 14:17:57,585 ERROR [pool-1-thread-18] custom.PreESXiHostCreate.call - failed to mount ucmap nfs
Thanks in advance.

Hi everybody,
Finally it turns it was a problem with the ASA. We apply a predefined rule in the ASA to allow NFS. We discover that the rule was not correctly defined, after creating a specific rule everything work just fine.

Can Cisco Prime Infra 2.1 work as syslog server

Hello all,
Customer want Cisco Prime Infra 2.1 to work as syslog server. they want to query text in syslog and get raw log file from Cisco Prime Infra. but when i see in user interface. I think that it cannot query and search text in syslog. but i am not sure whether we can get raw log file per devices from Cisco Prime Infra. Can anyone know about this.?
thanks
sompoj

Hi Sompoj,
In the prime infrastructure Syslogs are directly read from udp port 514 and then filtered
, the non SEV1 and SEV2 syslogs will be dropped and will not be entered into db . The
syslog messages will not be saved into log files .
Thanks-
Afroz
****Ratings Encourages Contributors ****

The cisco snmp oids do not work, I can't get cpu or memory data.

Hello. I want to monitor the cpu and memory usages on my cisco devices using snmp. I found the snmp oids related to cpu in the following page :
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a94.shtml
I just copy the table here:
But the oids in the table do not work on my devices. For example, I have a cisco 3550 switch with the ip 192.168.1.211, version 12.2(25)when I want to get the informations about the oids up in the table, I got these results:
It shows that the oids cisco given up in the table are not existed in my 3550 switch's MIB. More weird is that when i add a number "1" to
the end of the oid cisco given, I can get some meaningless data for some unkonwn item names like "entreprises.x.x".
For most mib items, the snmp oids work well on my switch. For example, the following graph shows the interface out rate of the swtich:
I think the essence is when I executed the following command:
in all the output results, there's not any item relevant with "cpu" or "memory", but most other items are ok, such as interfaces, as shown below:
IF-MIB::ifDescr.47 = STRING: FastEthernet0/39
IF-MIB::ifDescr.48 = STRING: FastEthernet0/40
IF-MIB::ifDescr.49 = STRING: GigabitEthernet0/1
IF-MIB::ifDescr.50 = STRING: GigabitEthernet0/2
IF-MIB::ifDescr.51 = STRING: Null0
IF-MIB::ifDescr.52 = STRING: Vlan1
IF-MIB::ifType.1 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.2 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.3 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.4 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.5 = INTEGER: ethernetCsmacd(6)
So why the cisco given oids won't work on my cisco switch, and how can I get the datas I want? Anyone has some advices? Thanks in advance!
In case the pictures I inserted missing, I attach my problem in the doc.

Have you looked at this previous discussion:
Can't Activate FaceTime

Cisco ISE IP Renewal not working

Hi all,
I am setting up a CWA with Cisco ISE to authenticate Guests and Employees by Web and assign them to Two different vlans. The authentication pass. The authZ Profiles are affected. but The IP address did not change according to vlan until I renew it manually from console ( >ipconfig /release >ipconfig /renew). I desactivated Java in browsers, I activated it again and added the IP of the ISE to the Exception List in Java setting but the IP address still not change automatically.
Any Ideas how to fix this Issue?
Thank you.

Hi Bouchaib,
Make sure you have put a check on the VLAN DHCP Release option.
If you are using ISE 1.3 then your path will be,
Guest Access > Configure > Guest Portals > Create, Edit or Duplicate > Portal Behavior and Flow Settings > VLAN DHCP Release Page Settings.
This affects the Central WebAuth (CWA) flow during final authorization when the network access changes the guest VLAN to a new VLAN. The guest’s old IP address must be released before the VLAN change and a new guest IP address must be requested through DHCP once the new VLAN access is in place. The IP address release renew operation varies by the browser and operating system used; Internet Explorer uses ActiveX controls, and Firefox and Google Chrome use Java applets. For non-Internet Explorer browsers, Java must be installed and enabled on the browser.
The VLAN DHCP Release option does not work on mobile devices. Instead, guests are requested to manually reset the IP address. This method varies by devices. For example, on Apple iOS devices, guests can select the Wi-Fi network and click the Renew Lease button.
For ISE 1.2 version, you can find the same option on the Guest Portal settings.

Why is Web Page Auth on MAC Filter Failure not working on Anchor Controller?

Hi,
I have implemented a Guest WLAN solution as per the recommended design from Cisco. We have two internal WiSM2 controllers providing services for Internal secure SSIDs. Both these controllers are members of a Mobility and RF management group.
Two 5508 controllers have been installed in our DMZ for resilience and have been placed into a separate Mobility group. All controllers (internal and external) have been linked together as mobility neighbours in a full mesh and a new SSID for Web Guest traffic has been anchored to the controllers in the DMZ.
Web page authentication works perfectly fine, but I cannot for the life of me get the MAC filtering override to work, i.e. if a MAC address is present, do not redirect to the splash page for web auth.
I can get MAC auth working by iteself, but not with the Layer 3 option selected for web page auth on mac filter failure.
I know I can get around this by just creating two separate SSIDs. But the business is used to just having the one SSID for all guest traffic.
Is this a known limitation when anchoring SSIDs to controllers in the DMZ ?

Hi Nicolas,
I guess they changed their mind to add this fix in 7.0MR3. Now the fix will be in 7.2 release planned to be release in FEB.
There is a documentation bug opened to add this to configuration guide :
CSCtw48727 Document CSCts54424. Limitations webauth on mac filter fail for anchor
Regards..Salil
CSCtw48727 Document CSCts54424. Limitations webauth on mac filter fail for anchor

Web service proxy and data control are not working properly

Hi,
I am working on jDeveloper 11.1.1.6
I have a SOA web service which requires 3 inputs and return with a set of data.
When I tried testing that web service in soapUI it is working perfect. But when I have created a web service proxy in my application and trying to test it from class (*******_ptClient) main method everytime it is replying with the output null
Also When I am requesting from the main method SOA is getting proper input (which I am providing in the main method) and SOA is returning proper output I have checked the SOA instance in em. So there is no problem in SOA side.
After that I have created web service data control and tested in that case also it is not showing any result.
What could be the problem ?
Please help.
Thanks
--NavinK

Hi Shay Shmeltzer,
Thanks for the reply.
I tried in HTTP Analyzer in JDeveloper and there also it is not working. My concern is :-
There are many other web services deployed on the same SOA server in same partition and they are working fine in HTTP analyzer and I am able to create and use the web service proxy as well. So as per my understanding there is nothing like network issues between SOA server and jDeveloper.
1 more thing When I am creating the proxy for this web service and requesting from the proxy's main method SOA is getting proper input (which I am providing in the main method) and SOA is returning proper output I have checked the SOA instance in em. So there is no problem in SOA side. The problem is jDeveloper is not able to get back that response which SOA is returning.
Please Help.
-- NavinK

BI Web services - Prompts with 'OR' condition are not working

Hi Gurus
I am using BIWS to build my Xcelsius dashboards . When i building a webservice from webi report having two data providers named fact & dim and i merging two data providers and the result i am using in a report.
The Fact data providers contains a query filters with 'OR' conditions applied in it.
when i test this webservice with the values it always displaying the last refreshed instance of report even i purge the data before building web service.
Could you please let me know is any one faced this issue. I am using Webi rich client 12.3.1 version
Note *: The web service works fine if i am using query filters with 'AND' condition.
Kindly check this do the needful
Cheers
Karun

Hai
Check this
Re: Web Intelligence BI Web Services and Xcelsius
http://everythingxcelsius.com/xcelsius-training/xcelsius-and-business-intelligence-web-services-biws/3642
http://www.sdn.sap.com/irj/scn/index?rid=/library/uuid/00536d65-f9cf-2e10-0eaa-f3346306dc1a
http://www.asug.com/CalendarEventDetails/tabid/150/eventid/2509/Default.aspx
http://www.forumtopics.com/busobj/viewtopic.php?p=819152

Query on Web , Enhanced menu- Query properties- Transfer button not working

Hello to all experts,
When We execute a query from query designer on to the web, if a user wants to go to Enhanced menu->Query properties and select any of the options existing there example "Tabular view, supress zeros ect ect " when he clicks on the button "TRANSFER at the bottom " to transfer his selected options , nothing happens... I have never seen this ? Bw netweaver platform 3.5 highest running patch is SAPKW35012
Does this have to do with any global query settings where tto look in for these settings? Also if this may help When we open query designer in local view I see that many buttons are inactive "Cell view" "Switch to global " ect and in Web application designer the "VIEW" option is grayed out as well ... Were are these settings maintained? Does anyone have any input , the most inportant being why iis the query properties "TRANSFER" button in Enhanced menu not working, i have seen no note on this
Thank you
Ayman

Hi Andy,
Nothing happened, meaning that the screen did not move, or the scaling factor was not set? Did you try to do it again?

USB Connect Cisco for Mac does not work

I created a USB for Cisco Connect on my desktop with Windows XP but it will not work to connect a Mac to the Internet.
When I insert the USB, the Connect Icon will not execute. Is there something special that has to be done?

Hey! Are you referring to the Cisco Connect software installed in the router? What's the model number of your router? Or if you're referring to the Smart Wifi software's USB feature, you may check this link:
http://homekb.cisco.com/Cisco2/ukp.aspx?vw=1&docid=f2fd60559043499c8643c3deea7c8ede_Overview_of_the_...

Cisco 871 NAT configuration not working

The problem is that NAT is not working for the "internal" network.
If i own the ip 10.0.0.15 for example and i try to reach x.x.x.x:65009 i will not work.
what's the problem?
here is the configuration:
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
description $FW_OUTSIDE$$ES_WAN$$ETH-WAN$
ip address x.x.x.x 255.255.255.192
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly
ip route-cache flow
duplex auto
speed auto
interface Vlan1
ip address 10.0.0.1 255.255.255.192
ip access-group 2 in
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip route-cache flow
ip tcp adjust-mss 1452
ip nat inside source list 1 interface FastEthernet4 overload
ip nat inside source static tcp 10.0.0.12 60022 x.x.x.x 65000 extendable
ip nat inside source static tcp 10.0.0.12 80 x.x.x.x 65001 extendable
ip nat inside source static tcp 10.0.0.12 21 x.x.x.x 65002 extendable
ip nat inside source static tcp 10.0.0.12 389 x.x.x.x 65003 extendable
ip nat inside source static tcp 10.0.0.12 3306 x.x.x.x 65004 extendable
ip nat inside source static tcp 10.0.0.12 10000 x.x.x.x 65005 extendable
ip nat inside source static tcp 10.0.0.12 443 x.x.x.x 65007 extendable
ip nat inside source static tcp 10.0.0.21 80 x.x.x.x 65009 extendable
ip nat inside source static tcp 10.0.0.21 22 x.x.x.x 65010 extendable
ip nat inside source static tcp 10.0.0.12 8080 x.x.x.x 65011 extendable
ip nat inside source static tcp 10.0.0.21 21 x.x.x.x 65012 extendable
ip nat inside source static tcp 10.0.0.21 3306 x.x.x.x 65013 extendable
logging trap debugging
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 10.0.0.0 0.0.0.63
access-list 2 deny 10.0.0.8
access-list 2 deny 10.0.0.2
access-list 2 deny 10.0.0.3
access-list 2 deny 10.0.0.6
access-list 2 deny 10.0.0.7
access-list 2 deny 10.0.0.4
access-list 2 deny 10.0.0.5
access-list 2 permit 0.0.0.0 10.0.0.63
Posted by WebUser ??????? ???

No, the ranges are not the same. That is, they share the same B-class stats, but no C-class.
Incidentally, the extendable parameter is present in this ios version. When I change the parameter interface dialer0 to the ip address associated with the interface, extendable is addedd automatically. No joy however.
Today I'm going to try and downgrade the ios, another router with 12.4(4)T1 does have functional port mappings....

Web Interface of Cisco Prime 2.1 not working

Similar Messages

Maybe you are looking for