Web interface on Cisco Prime Infrastructure express not coming up

Trying to get Cisco Prime Infrastructure express installed. The installation completes without any error but when I try to run show NCS or attempt to start stop the service get the following output
usdayt-cis-002/admin# show application status NCS
% Application NCS is not installed
usdayt-cis-002/admin# ncs start
sh: /opt/CSCOlumos/bin/wcsadmin.sh: No such file or directory
here's the output from show inventory
usdayt-cis-002/admin# show inventory
NAME: "Cisco-VM chassis", DESCR: "Cisco-VM chassis"
PID: Cisco-VM-SPID , VID: V01 , SN: 1GP9SNNE5HJ
Total RAM Memory: 16304916 kB
CPU Core Count: 8
CPU 0: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 1: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 2: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 3: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 4: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 5: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 6: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 7: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
Hard Disk Count(*): 1
Disk 0: Device Name: /dev/sda
Disk 0: Capacity: 314.50 GB
Disk 0: Geometry: 255 heads 63 sectors/track 38244 cylinders
NIC Count: 1
NIC 0: Device Name: eth0
NIC 0: HW Address: 00:50:56:AF:76:34
NIC 0: Driver Descr: e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
(*) Hard Disk Count may be Logical.
usdayt-cis-002/admin# show disks
disk: 1% used (184324 of 44628400)
temp. space 2% used (35792 of 1967952)
Internal filesystems:
all internal filesystems have sufficient free space
any idea what could be the issue here?

OK, that's the correct one. Can you verify the checksum of the file? It should be:
91dc6ebc446c1c9c000c69af4be93102
If that's OK, I would delete the VM and try installing the ova once more.
Other than that, I'd suggest calling the TAC if it's a supported installation (i.e. not an evaluation copy).

Similar Messages

Web Interface of Cisco Prime 2.1 not working

Excuse me!
I install the trial version cisco prime 2.1 (OVA) on ESXi server
I can ping cisco prime but web interface of cisco prime not worinking
prime/admin# ncs status
Health Monitor Server is running.
Ftp Server is running
Database server is running
Tftp Server is running
Matlab Server is running
NMS Server is running.
Plug and Play Gateway is running.
SAM Daemon is running ...
DA Daemon is running ...
Syslog Daemon is running ...

Services running fine..
check it with other Browser , Supported browser are below::
–   Google Chrome 31 or later.
–   Microsoft Internet Explorer 8.0 or 9.0 with Google Chrome Frame plugin (users logging in to the simplified Lobby Ambassador interface do not need the plugin).
–   Mozilla Firefox ESR 24.
–   Mozilla Firefox 24, 25 or 26.
If above does not help , reboot the server once and check the issue again.
Thanks-
Afroz
***Ratings Encourages Contributors ****

Web Interface of Cisco Prime Infrastructure Not Working

Hi All,
I installed the trial version of Cisco Prime Infrastructure 1.2 on ESXi server.
It installed propersly and and i am able to ping it and also ssh into it.
But when I try to access it via web interface, it does not work.
I am provided with a login screen but after putting my credentials the page goes blank.
There also an error on the page "Error occured while fetching Meatdata for Slider Panel" and there is a advertisemnt to download Google chrome Framework.
When i do "NCS status" in CLI i see that every service is running.
Does anyone know how to solve this.
All your help is highly appreciated.

Google Chrome Frame isnt supported anymore, using Google Chrome doesnt work with all features and forget about Firefox. Up until this morning I had it working on IE11 but some update caused me to have this problem again. Cisco needs to get this fixed. I use several applications from Cisco and they still can't figure out a way to have them all work on a single browser.

Cisco Prime Infrastructure, Express, licensing

Are there any funcionatility limitation between each edition of the Cisco Prime Infrastructure other than supported number of devices?
Does it support turning APs on and off on a predefined scheduled?
I read in the manual "Cisco Prime Infrastructure Classic View Configuration Guide for Wireless Devices" that it is possible to Managing WLAN Status Schedules. Does it require the assurance license feature set or will lifecycle license will be sufficient?

I believe you could create a scheduled Lightweight AP Configuration Template job and have it simply turn off the radios on the selected APs. Make it recurring (every night at a certain time) and add a complementary recurring job to turn the radios back on at the desired time.
See the following screeenshot from PI 2.0 (click to enlarge):

Consultations on Cisco Prime Infrastructure 2.2

I recently installed Cisco Prime Infrastructure 2.2 and I have 2 questions regarding configuration:
1. What configurations should run for vulnerability when some event occurs on a switch an alarm is lifted in the Cisco Prime Infrastructure 2.2?
2. Is there any way to put a device into maintenance mode in the web interface of Cisco Prime Infrastructure 2.2, so that can not be spoiled reports regarding equipment availability during the execution of maintenance?

1. If you configure PI as an SNMP and syslog server for your devices and have enabled logging traps etc., PI's alarm browser will show the alarms. If you want them to be sent to you via email, you can do that under the Admin menu for setting up your Mail server and clicking the link to "Configure email notification for individual alarm categories." (see below - open in new tab to zoom). It's not completely customizable but what you see there is the current product capabilities in that regard.
2. No, this is not currently an available feature in PI 2.2.

Cisco Prime Infrastructure 1.3 Web Log Invalid user password

Hi,
I recently installed Cisco Prime Infrastructure 1.3 per the set up guide. I was able to login into the webinterface.
Then I insert the radius server and reload ncs. Since then I'm not able to login to the web interface. I get the following error message "Invalid Username or Password. Please try again". Even when I set the ncs root user with a new password. One issue could be that i forgot the enable fallback to local.
Is there a way to change the radius config back via cli?
Thanks a lot
Hansruedi

Hi Hansruedi,
Thanks you for your help and your time.
I followed your recomandation until the fourth step.
But after this step, I lost the web page connection.
I check nsc status but all is running :
NMS still stopped. NMS must be running to have an access by web page ?
I restart Prime (by reload command) but nothing changed.
Thanks

Cisco Prime Infrastructure 1.2 OVA - URL/FTP not working

The ESXi install of the theNCS OVA was successful. NCS seems to load and activate interfaces. The console session is working. Using compliant browsers; https://<ip address> does not work. When I stop "ncs" or halt the vm the web page responds shortly but then the connection is lost. I used "show ports" and tried https://<ip address>/8082 and get a login from the Cisco Prime Infrastructure Health Monitor URL. There is a prompt for the authorization key. How can I confirm the installation is complte and all services are up and running
Thanks
Terry

After digging almost 1 month, I found the answer.
When you do provision from ESXi with ova file, you have to create "Thick Provision" otherwise, you wiil have same problem such as "some services are not up"
In my case, I am running ESXi on the top of VM WorkStation since I don't have any ESXi server. When I added 250GB into the WorkStation and did provision with "Thick" it works !!!
Since my testing envrionment is little complicated (ESXi with VM WorkStation), I added first 250GB HDD into ESXi, and tried. It didn't work. So I added 250GB into VM WorkStation and did provision through Workstation, it worked (If you don't understand this statements, do not worry. If you have ESXi server, you don't need to worry about)
As far as cisco ova is concerned, when I talked to one of my my friend who was working for new ACS (Virtual Appliance) he had same issue. He also solved with "Thick Provision"
FYI, even if when I installed with "Thin Provision", PI 1.2 used only 10GB out of 200GB, so I did not think that I should use "Think Provision". But definitely not.

Cisco Prime Infrastructure 1.3 Web Log In Error

Hi,
I recently installed Cisco Prime Infrastructure 1.3 per the set up guide. I am able to log into the VM back end but when I try to log into the web interface with the admin account I get the following error message "Invalid Username or Password. Please try again". I verified that the username and password are correct but I still can not get in.

I think there is some bug (or feature) that makes that the accounts defined during setup are not valid in the web gui.
Since the users I created using CLI, work when I SSH into the PI 1.3, I know they are correct.
Clearly the web part uses a different way to authenticate users. I'm told all this worked just fine in PI 1.2, so not sure what cisco is up to.
To resolve this use the root account to login in the web interface.
It has the same pw as the admin user.
There you can create an admin account (and or others)
Cheers,
Michel

Cisco prime infrastructure not detect IP address of clients

hi all,
I have Cisco Prime infrastructure 1.2 and when move to monitor >> clients tab it lists me all the clients in my network but their IP address list estates "not detected" ?
please any advice?
I appreciate your kindly support.

Just an update that while this appears to have worked fairly well (as far as Cisco Management Planes go), there was one small 'gotcha' I've noticed so far:
After the services came back up, the entries for our RADIUS servers did not function. No, not because I didn't update the clients address record on the RADIUS server itself, but because the RADIUS server record(s) within CPI have a field called 'Local Interface IP' that still reflects the previous IP assigned to CPI. A quick edit/save with the new interface fixes up the issue however.
Cheers!

Cisco Prime Infrastructure 1.4 SNMP Traps are not converted into Alarms

Hi everybody,
I just configured SNMP Traps on a Cisco Catalyst 3750-x to send to our Cisco Prime Infrastructure 1.4 Appliance.
Now I forced the Switch to send some traps (Power off a Power Supply, Interface errdisable). The only events I see in Alarms & Events on PI is the same information message everytime:
Configuration management event has been recorded in ccmHistoryEventTable.
I think the forced traps should be converted into alarms? Why can't I see them?
Thanks,
Marc

Ok, I started debugging as you said. I get the following output:
Mar 13 09:28:13.711: SNMP: V2 Trap, reqid 11689, errstat 0, erridx 0
sysUpTime.0 = 198609846
snmpTrapOID.0 = ciscoSyslogMIB.2.0.1
clogHistoryEntry.2.1688 = PM
clogHistoryEntry.3.1688 = 5
clogHistoryEntry.4.1688 = ERR_RECOVER
clogHistoryEntry.5.1688 = Attempting to recover from bpduguard err-disable state on Gi1/0/13
clogHistoryEntry.6.1688 = 198609844
Mar 13 09:28:13.737: SNMP: Queuing packet to xx.xx.xx.xx
Looks like the Switch is sending SNMP Traps from the ciscoSyslogMIB. Is this why PI can't show the Traps and convert it into a alarm?
After this test I configured logging (syslog) to the PI. Now the errors are showed but still not converted into alarms. I just want to be notified by email when such errors occurs.
Thanks,
Marc

Cisco Prime Infrastructure 1.2 OVA not found

Hi all,
I want to download Cisco Prime Infrastructure 1.2 OVA but I can't find it, there is just "Cisco Prime Infrastructure 1.2 Plug and Play for Virtual Appliance " . Is this the right OVA ?
Thanks for your help
BR
Aaziz

Hi Aaziz,
Unfortunately this download of this file is not available anymore on cisco.com site.
As an alternative, you can download PI 1.3 OVA, where you can find the same features and
interface:
http://software.cisco.com/download/release.html?mdfid=284652876&softwareid=284272932&relea
se=1.3&relind=AVAILABLE&rellifecycle=&reltype=all
Note: you can use the same license of PI 1.2 on PI 1.3
Thanks-
Afroz
***Ratings Encourages Contributors ***

Cisco Prime Infrastructure 2.1 Express OVA failing to boot up

Hi all, i'm wondering if you can help me, i'm trying to deploy Cisco Prime Infrastructure in a lab envrionment but it's not working correctly.
I've deployed "PI-VA-2.1.0.0.87-Express.ova" to a VMware ESXI 5.1U2 hypervisor with 2x AMD 8128HE CPUs, 96GB RAM, ASUS KGPE-D16 motherboard. The installation works fine, I can answer all the questions and enter the IP address. Once the system reboots, it hangs at the following screen:
"Kernel direct mapping tables up to 340000000 @ 10000-1c000" is the last thing I see
Interestingly at this point I can actually ping the VM... I cant connect to the managemnet console on HTTPS though :(
I did find some related info on a blog https://deekayen.net/kernel-alive-lock which mentions booting with "noapic", however when I try to press "P" on the grub boot loader it prompts me to enter a password which I dont know! My normal admin passwords arent working.
Any help to ge tthis running would be greatly appreciated
Thanks in advance
Ben

The server takes about 30 mins to boot up, it's not actually broken it's just extremely slow .. I have found numerous people reporting this issue online, and our production system also does this! I guess my original problem is solved, although I would prefer this issue not to exist!

Including Interface Description in Cisco PRime Infrastructure Alarm Message

Hi all,
i succesfully configured a Cisco Prime Infrastructure 2.1 applliance to display an alarm and to send me an e-mail when switch uplink ports goes down.
The text displayed in alarm message is :
port 'interface_id' is down on device 'device_ip_address'
I'd like to include in this text also the interface description so the text will display :
port 'interface_id' 'interface_descriprion' is down on device 'device_ip_address'
Is this possible?
Thankyou in advance

Hi,
i followed these steps :
SWITCH SIDE
- configured Prime Infrastructure as snmp-server host;
- enabled snmp-traps for linkup and linkdown events globally;
- disabled snmp-traps for linkup and linkdown on non relevant interfaces using the no snmp trap link-status command
PRIME INFRASTRUCTURE SIDE
- under "Deploy/Monitor Deployment" i deployed template "Interface Health" for all the interested switches
- under "Administration/System Settings/Mail Server Configuration" configured my internal SMTP server to make Prime Infrastructure able to send e-mails
- under "Operate/Alarms & Events" click on "Email Notifications" , then on "Switches and Hubs"
- check the "critical" box , insert the destination e-mail address into the "To" field then click "Save"
- check the "switches and Hubs" box and then click Save
As i know is possible to avoid to configure every single not-interesting port on the switches with "no snmp trap link-status" command (it's a bit annoying when you have tens of switches), using Port Grouping configuration on PI but i tried it without success.
Hope this helps.
Best Regards,

Cisco Prime Infrastructure 2.0 not showing alerts from switch

Hello,
I have a prime infrastructure 2.0 running at a customer place and the customer now complains that he is not receiving link up/down messages from the switch. When i checked I have seen that if I shut down a port in the switch the prime identifies after a long time, but its not generating an alarm still. How can I fine tune the prime to fix this issue. Please help on this.
Thanks in advance

Hi,
Same problem here.
I am using Cisco Prime Infrastructure 2.0 (evaluation version for 60 days). I want to deploy port monitoring for my trunk ports between switches and some other important ports e.g. servers. Basically I want to get alarms when these ports are down, there are errors on ports and etc.
So in Design>Port Grouping I created User Defined group with important ports. In Deploy>Monitoring Deployment I selected Interface Health (default)>Deploy selected Port Groups and when selected port group I created.
Now the rule shows Deployed: Yes and Status: Active. After that I just pulled out one port which was in monitored group, waited 5min as it is set in Interface Health (default) template, and nothing happened, and worse, alarms started to show up of other ports where regular users are connected (computers was turned off), which I do not want to see at all. I tried redeploy template, I even created my own template but still no desired result.
Any suggestions how to make port monitoring work?

Cisco Prime Infrastructure 2.2 Rest API XML does not add LF

I am using several scripts that dig the data from XML files created through Cisco Prime Infrastructure Rest API. It worked fine until 2.1. Now, with 2.2, seems Cisco stopped adding LF to each line and everything is 'one' line.
Here is an example with 2.1, there is a LF to the end of each line:
?xml version="1.0" encoding="UTF-8" standalone="yes"?>
<queryResponse type="AccessPointDetails" rootUrl="https://server/webacs/api/v1/data" requestUrl="https://server/webacs/api/v1/data/AccessPointDetails?type=contains(UnifiedAp)&.full=true&.maxResults=1000&.firstResult=0" responseType="listEntityInstances" count="715" first="0" last="714">
    <entity url="https://server/webacs/api/v1/data/AccessPointDetails/1505569" type="AccessPointDetails" dtoType="accessPointDetailsDTO">
        <accessPointDetailsDTO id="1505569" displayName="1505569">
            <adminStatus>ENABLE</adminStatus>
            <apType>AP1240</apType>
            <cdpNeighbors>
                <cdpNeighbor>
                    <capabilities>Switch IGMP </capabilities>
                    <duplex>Half Duplex</duplex>
                    <interfaceSpeed>100Mbps</interfaceSpeed>
                    <localPort>2</localPort>
                    <neighborIpAddress>10.1.1.1</neighborIpAddress>
                    <neighborName>switch</neighborName>
                    <neighborPort>FastEthernet0/1</neighborPort>
                    <platform>cisco WS-C3560-8PC</platform>
                </cdpNeighbor>
Now, with 2.2, there is not LF anywhere:
?xml version="1.0" encoding="UTF-8" standalone="yes"?><queryResponse type="AccessPointDetails" rootUrl="https://server/webacs/api/v1/data" requestUrl="https://server/webacs/api/v1/data/AccessPointDetails?type=contains(UnifiedAp&.full=true&.maxResults=1000&.firstResult=0" responseType="listEntityInstances" count="715" first="0" last="714">
<entity url="https://server/webacs/api/v1/data/AccessPointDetails/1505569" type="AccessPointDetails" dtoType="accessPointDetailsDTO">
<accessPointDetailsDTO id="1505569" displayName="1505569"><adminStatus>ENABLE</adminStatus><apType>AP1240</apType><cdpNeighbors><cdpNeighbor>
Does anyone know, is this intentional or a mistake? Or is there a way how I control this?
I am reading on-line CPI Rest API docs, but seems cannot find anything.
Thanks,
Vlad

PI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks

Web interface on Cisco Prime Infrastructure express not coming up

Similar Messages

Maybe you are looking for