WebCam not functioning on cold boot. Reappear on reboot.

I just bought a TouchSmart 610t. I found out today if I start the computer from a power cycle (shut off and then power up), the webcam will go missing (no imaging device, question mark in unknown device dr in USB). If I reboot the computer (via CTRL+ALT+DEL), the webcam shows up again. I wonder if anyone has seen this.
I recently installed Windows 7 SP1 along with other updates. Not sure if this is relevant.
Where can I find the device driver for the webcam?
I'll run more experiments to see if reboot fixes it 100%. If so, I can live with it. Love the computer otherwise.
Thanks!

Similar Messages

ESATA HDD not recognised on cold boot, OK on reboot

Hi, I have a HP Elitebook 8740w from which I have removed the internal HDD and connected an eSATA HDD which is powered from the USB bus (I've done this for security purposes). I'm having a problem whereby when booting at initial power-on, a Non-System disk or disk error is encountered after the HP screen. I can then boot into Windows by pressing CTRL+ALT+DEL however having to do this each time I start up is not ideal. Also this error is not seen when rebooting, only at power on. I have tried powering the HDD from the supplied AC power pack and the problem disappears which make me think it is an issue with the USB power (either insufficient current supplied or full power is not available at start up). I have tried all combinations of USB2.0 and SuperSpeed USB ports with the supplied USB Y cable without success in removing this error. Any ideas? I would prefer to run the HDD from the USB ports to save carrying the AC power pack and because often only one power point is available. Thanks

I think I've worked it out... I was running the laptop on mains power only with battery removed. Tried it with the battery installed and problem disappears, it must provide extra power at startup to spin up the HD. Laptop AC adaptor is 200W though, would have thought this would be enough...

MSI E350IA-E45 USB Not recognised after cold boot.

Any one else have the same issue? My asus (Bluetooth) BT211 is not recognised after cold boot.
I also found the front USB's losing power when PC turned off. Connected them up to 5VSB to fix the issue.
MSI tech has not been back to me if this is a fault design, My motherboard issue or bios issue? Which also means to charge via front USB not work when turned off.
And to top it off I cannot find an answer to whether the Wake on Bluetooth USB is supposed to work?

Quote from: mickas on 12-August-11, 20:09:58
I also found the front USB's losing power when PC turned off. Connected them up to 5VSB to fix the issue.
How did you connect up the USB ports to 5VSB?
I have a similar issue with a newer MSI board and my USB mouse; I'd have to remove and re-insert the USB connection to the mouse after each cold boot in order for it to be recognized. I did a kludge fix by looping the mouse through a powered USB hub that supplies power to connected devices even when the PC is off.
This MSI board doesn't have a hardware jumper to enable 5VSB to the USB ports, unlike other motherboards. Also, none of the "green" or wakeup settings in the BIOS would cause the USB ports to have power when the PC is off.
So, how do you connect 5VSB to the USB ports? I've heard that crossing the regular 5V rail with 5VSB is a no-no, so I can't imagine how you did it.

USB Devices not working on cold boot

On a cold boot, I get either my mouse (Microsoft Optical) or my modem (see signature) not switched on. If I reboot, or just re-plug them in, they switch on and Windows detects them. The modem is attached to a port on the mobo, and the mouse to a powered USB hub. The only other device powered at boot is a joypad (Thrustmaster Dual Power 2), which always works at boot. Devices switched off at boot are a printer/scanner, desktop light, and an extension lead for a thumb drive.
Does anyone have a solution to this?

Quote from: artur.aragao on 13-February-05, 11:59:04
Expensive friend,
Step for the same problems, where already I communicated diverse times with the support of the MSI not obtaining a definitive solution for this problem. It does not go to advance nor to make magic, therefore the problem has left of the plate-mother and not of the operational system. I have one mouse of the Microsoft who possesss led and when I give the departure in the PC the same does not light in the screen of informs of devices of the CMOS. It would have.
Then I am obliged to remove and to place mouse of the door usb so that mouse functions. The problem is that I have that to faer this almost all time that I bind the micron.
The bios beta that decided this problem palliative were 1.5B8.
I see that all the ones that pass for this problem are receiving the had respect, therefore this problem already is old and no solution was adopted until the moment for the manufacturer.
If my problem to continue, I will get rid myself of my plate and I will migrarei for another manufacturer who hears me and she respects me, therefore we make many times investment s in products that would not have to give as much migraine.
We buy TVs and DVDs and we do not pass for problems as these.
I was disappointed with the MSI in this part. It would go to acquire a VGA 6600GT, but today I think seriously about not buying more nothing of the MSI.
Still more for that it occurred with the 6800GT that were being sales and in the truth they were 6800NU.What it is this?
I advise to the friend who if not to decide its problem in at least 1 month, it speaks brazenly of its mainboard and it buys of another
manufacturer as the ABIT or same Gibagyte.
I have friends that they possess plates of the Gigabyte and are very happy.
Artur de Souza Aragão
HUH??? You did know this is an English languager board right? If not then please read the forum rules. Also note that hijacking someone else's post so you can complain is against the rules here as well.
This is entirely a user to user forum and as such MSI is not here nor do they read it. So yopur complaints whatever they may be as we can't entirely read your post is not getting to those folks that you want to complain at. Instead you are just making the rest of us upset for no visable reason. If you want to contact MSI to copmplain may I suggest a phone call. You may also want to call someone there that actually speaks the same language so there are no miscommunications as what is happening here.
Edit - his posts on this subject were all removed due to spamming the forum.

ATI Graphics card not detected on cold boot, works on warm boot

Hi All,
I hope you can help me out with this.
I'm using Radeon HD7850 with ATI-Catalyst.
The issue is, if I do a cold boot (physically turn off the power, turn back on) the system won't boot into X, only tty.
At this point, a reboot works fine.
Or if I don't turn off the power, just shutdown and reboot (warm boot), it works ok.
Here's the Xorg log on cold boot:
[ 2.226]
X.Org X Server 1.12.4
Release Date: 2012-08-27
[ 2.226] X Protocol Version 11, Revision 0
[ 2.226] Build Operating System: Linux 3.4.8-1-ARCH x86_64
[ 2.226] Current Operating System: Linux dmanPC 3.5.3-1-ARCH #1 SMP PREEMPT Sun Aug 26 09:14:51 CEST 2012 x86_64
[ 2.226] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=3766a71b-dbfe-4cc2-b7bd-948878b5da67 ro nomodeset quiet
[ 2.226] Build Date: 27 August 2012 08:04:39AM
[ 2.226]
[ 2.226] Current version of pixman: 0.26.2
[ 2.226] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 2.226] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 2.226] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Sep 28 05:57:41 2012
[ 2.227] (==) Using config file: "/etc/X11/xorg.conf"
[ 2.228] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 2.228] (==) ServerLayout "aticonfig Layout"
[ 2.228] (**) |-->Screen "aticonfig-Screen[0]-0" (0)
[ 2.228] (**) | |-->Monitor "aticonfig-Monitor[0]-0"
[ 2.229] (**) | |-->Device "aticonfig-Device[0]-0"
[ 2.229] (==) Automatically adding devices
[ 2.229] (==) Automatically enabling devices
[ 2.231] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 2.231] Entry deleted from font path.
[ 2.231] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 2.231] Entry deleted from font path.
[ 2.231] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 2.231] Entry deleted from font path.
[ 2.231] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 2.232] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 2.232] Entry deleted from font path.
[ 2.232] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 2.232] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 2.232] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 2.232] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 2.232] (II) Loader magic: 0x7c8b00
[ 2.232] (II) Module ABI versions:
[ 2.232] X.Org ANSI C Emulation: 0.4
[ 2.232] X.Org Video Driver: 12.1
[ 2.232] X.Org XInput driver : 16.0
[ 2.232] X.Org Server Extension : 6.0
[ 2.232] (--) PCI:*(0:7:0:0) 1002:6819:1462:2730 rev 0, Mem @ 0xe0000000/268435456, 0xf7b00000/262144, I/O @ 0x0000c000/256, BIOS @ 0x????????/131072
[ 2.232] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 2.232] (II) "extmod" will be loaded by default.
[ 2.232] (II) "dbe" will be loaded by default.
[ 2.232] (II) "glx" will be loaded by default.
[ 2.232] (II) "record" will be loaded by default.
[ 2.232] (II) "dri" will be loaded by default.
[ 2.232] (II) "dri2" will be loaded by default.
[ 2.232] (II) LoadModule: "extmod"
[ 2.233] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 2.233] (II) Module extmod: vendor="X.Org Foundation"
[ 2.233] compiled for 1.12.4, module version = 1.0.0
[ 2.233] Module class: X.Org Server Extension
[ 2.233] ABI class: X.Org Server Extension, version 6.0
[ 2.233] (II) Loading extension MIT-SCREEN-SAVER
[ 2.233] (II) Loading extension XFree86-VidModeExtension
[ 2.233] (II) Loading extension XFree86-DGA
[ 2.233] (II) Loading extension DPMS
[ 2.233] (II) Loading extension XVideo
[ 2.233] (II) Loading extension XVideo-MotionCompensation
[ 2.233] (II) Loading extension X-Resource
[ 2.233] (II) LoadModule: "dbe"
[ 2.233] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 2.234] (II) Module dbe: vendor="X.Org Foundation"
[ 2.234] compiled for 1.12.4, module version = 1.0.0
[ 2.234] Module class: X.Org Server Extension
[ 2.234] ABI class: X.Org Server Extension, version 6.0
[ 2.234] (II) Loading extension DOUBLE-BUFFER
[ 2.234] (II) LoadModule: "glx"
[ 2.234] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 2.236] (II) Module glx: vendor="Advanced Micro Devices, Inc."
[ 2.236] compiled for 6.9.0, module version = 1.0.0
[ 2.236] (II) Loading extension GLX
[ 2.236] (II) LoadModule: "record"
[ 2.236] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 2.237] (II) Module record: vendor="X.Org Foundation"
[ 2.237] compiled for 1.12.4, module version = 1.13.0
[ 2.237] Module class: X.Org Server Extension
[ 2.237] ABI class: X.Org Server Extension, version 6.0
[ 2.237] (II) Loading extension RECORD
[ 2.237] (II) LoadModule: "dri"
[ 2.237] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 2.237] (II) Module dri: vendor="X.Org Foundation"
[ 2.237] compiled for 1.12.4, module version = 1.0.0
[ 2.237] ABI class: X.Org Server Extension, version 6.0
[ 2.237] (II) Loading extension XFree86-DRI
[ 2.237] (II) LoadModule: "dri2"
[ 2.238] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 2.238] (II) Module dri2: vendor="X.Org Foundation"
[ 2.238] compiled for 1.12.4, module version = 1.2.0
[ 2.238] ABI class: X.Org Server Extension, version 6.0
[ 2.238] (II) Loading extension DRI2
[ 2.238] (II) LoadModule: "fglrx"
[ 2.238] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
[ 2.262] (II) Module fglrx: vendor="FireGL - AMD Technologies Inc."
[ 2.262] compiled for 1.4.99.906, module version = 8.98.2
[ 2.262] Module class: X.Org Video Driver
[ 2.262] (II) Loading sub module "fglrxdrm"
[ 2.262] (II) LoadModule: "fglrxdrm"
[ 2.262] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[ 2.263] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[ 2.263] compiled for 1.4.99.906, module version = 8.98.2
[ 2.263] (II) AMD Proprietary Linux Driver Version Identifier:8.98.2
[ 2.263] (II) AMD Proprietary Linux Driver Release Identifier: 8.982
[ 2.263] (II) AMD Proprietary Linux Driver Build Date: Jul 27 2012 20:37:56
[ 2.263] (++) using VT number 8
[ 2.264] (WW) Falling back to old probe method for fglrx
[ 2.269] (II) Loading PCS database from /etc/ati/amdpcsdb
[ 2.271] (WW) fglrx: No matching Device section for instance (BusID ) found
[ 2.271] (EE) No devices detected.
[ 2.271]
Fatal server error:
[ 2.271] no screens found
[ 2.271]
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 2.271] Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 2.271]
Here's the same log for warm boot:
[ 2.289] (++) using VT number 8
[ 2.290] (WW) Falling back to old probe method for fglrx
[ 2.295] (II) Loading PCS database from /etc/ati/amdpcsdb
[ 2.296] (--) Chipset Supported AMD Graphics Processor (0x6819) found
[ 2.296] (WW) fglrx: No matching Device section for instance (BusID PCI:0@6:0:1) found
[ 2.297] (II) AMD Video driver is running on a device belonging to a group targeted for this release
[ 2.297] (II) AMD Video driver is signed
[ 2.297] (II) fglrx(0): pEnt->device->identifier=0x82b7a0
[ 2.297] (II) fglrx(0): === [xdl_xs112_atiddxPreInit] === begin
[ 2.297] (II) Loading sub module "vgahw"
[ 2.297] (II) LoadModule: "vgahw"
[ 2.298] (II) Loading /usr/lib/xorg/modules/libvgahw.so
[ 2.298] (II) Module vgahw: vendor="X.Org Foundation"
[ 2.298] compiled for 1.12.4, module version = 0.1.0
[ 2.298] ABI class: X.Org Video Driver, version 12.1
[ 2.298] (**) fglrx(0): Depth 24, (--) framebuffer bpp 32
[ 2.298] (II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[ 2.298] (==) fglrx(0): Default visual is TrueColor
[ 2.298] (**) fglrx(0): Option "OpenGLOverlay" "0"
[ 2.298] (**) fglrx(0): Option "DPMS" "true"
[ 2.298] (==) fglrx(0): RGB weight 888
[ 2.298] (II) fglrx(0): Using 8 bits per RGB
[ 2.298] (==) fglrx(0): Buffer Tiling is ON
[ 2.299] (II) Loading sub module "fglrxdrm"
[ 2.299] (II) LoadModule: "fglrxdrm"
[ 2.299] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[ 2.299] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[ 2.299] compiled for 1.4.99.906, module version = 8.98.2
[ 2.299] ukiDynamicMajor: found major device number 251
[ 2.299] ukiDynamicMajor: found major device number 251
[ 2.299] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[ 2.299] ukiOpenDevice: node name is /dev/ati/card0
[ 2.299] ukiOpenDevice: open result is 11, (OK)
[ 2.299] ukiOpenByBusid: ukiOpenMinor returns 11
[ 2.299] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[ 2.299] (**) fglrx(0): NoAccel = NO
[ 2.299] (**) fglrx(0): AMD 2D Acceleration Architecture enabled
[ 2.299] (--) fglrx(0): Chipset: "AMD Radeon HD 7800 Series " (Chipset = 0x6819)
[ 2.299] (--) fglrx(0): (PciSubVendor = 0x1462, PciSubDevice = 0x2730)
[ 2.299] (==) fglrx(0): board vendor info: third party graphics adapter - NOT original AMD
[ 2.299] (--) fglrx(0): Linear framebuffer (phys) at 0xe0000000
[ 2.299] (--) fglrx(0): MMIO registers at 0xf7c00000
[ 2.299] (--) fglrx(0): I/O port at 0x0000c000
[ 2.299] (==) fglrx(0): ROM-BIOS at 0x000c0000
[ 2.300] (II) fglrx(0): AC Adapter is used
[ 2.303] (II) fglrx(0): Primary V_BIOS segment is: 0xc000
[ 2.303] (II) Loading sub module "vbe"
[ 2.303] (II) LoadModule: "vbe"
[ 2.303] (II) Loading /usr/lib/xorg/modules/libvbe.so
[ 2.304] (II) Module vbe: vendor="X.Org Foundation"
[ 2.304] compiled for 1.12.4, module version = 1.1.0
[ 2.304] ABI class: X.Org Video Driver, version 12.1
[ 2.304] (II) fglrx(0): VESA BIOS detected
[ 2.304] (II) fglrx(0): VESA VBE Version 3.0
[ 2.304] (II) fglrx(0): VESA VBE Total Mem: 16384 kB
[ 2.304] (II) fglrx(0): VESA VBE OEM: AMD ATOMBIOS
[ 2.304] (II) fglrx(0): VESA VBE OEM Software Rev: 15.17
[ 2.304] (II) fglrx(0): VESA VBE OEM Vendor: (C) 1988-2010, Advanced Micro Devices, Inc.
[ 2.304] (II) fglrx(0): VESA VBE OEM Product: PITCAIRN
[ 2.304] (II) fglrx(0): VESA VBE OEM Product Rev: 01.00
[ 2.309] (II) fglrx(0): AMD Video BIOS revision 9 or later detected
[ 2.309] (--) fglrx(0): Video RAM: 2097152 kByte, Type: GDDR5
[ 2.309] (II) fglrx(0): PCIE card detected
[ 2.309] (--) fglrx(0): Using per-process page tables (PPPT) as GART.
[ 2.309] (WW) fglrx(0): board is an unknown third party board, chipset is supported
[ 2.311] (II) fglrx(0): Using adapter: 6:0.0.
[ 2.320] (II) fglrx(0): [FB] MC range(MCFBBase = 0xf400000000, MCFBSize = 0x80000000)
[ 2.458] (II) fglrx(0): Interrupt handler installed at IRQ 48.
[ 2.458] (II) fglrx(0): RandR 1.2 support is enabled!
[ 2.458] (II) fglrx(0): RandR 1.2 rotation support is enabled!
[ 2.458] (==) fglrx(0): Center Mode is disabled
[ 2.458] (II) Loading sub module "fb"
[ 2.458] (II) LoadModule: "fb"
[ 2.458] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 2.461] (II) Module fb: vendor="X.Org Foundation"
[ 2.461] compiled for 1.12.4, module version = 1.0.0
[ 2.461] ABI class: X.Org ANSI C Emulation, version 0.4
[ 2.461] (II) Loading sub module "ddc"
[ 2.461] (II) LoadModule: "ddc"
[ 2.461] (II) Module "ddc" already built-in
[ 2.571] (II) fglrx(0): Finished Initialize PPLIB!
[ 2.577] (II) fglrx(0): Output DFP1 using monitor section aticonfig-Monitor[0]-0
[ 2.577] (II) fglrx(0): Output DFP2 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP3 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP4 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP5 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP6 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP7 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP8 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP9 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP10 has no monitor section
[ 2.577] (II) fglrx(0): Output CRT1 has no monitor section
[ 2.578] (II) Loading sub module "ddc"
[ 2.578] (II) LoadModule: "ddc"
[ 2.578] (II) Module "ddc" already built-in
[ 2.578] (II) fglrx(0): Connected Display0: DFP10
[ 2.578] (II) fglrx(0): Display0 EDID data ---------------------------
[ 2.578] (II) fglrx(0): Manufacturer: SAM Model: 524 Serial#: 1280455218
[ 2.578] (II) fglrx(0): Year: 2009 Week: 20
[ 2.578] (II) fglrx(0): EDID Version: 1.3
[ 2.578] (II) fglrx(0): Digital Display Input
[ 2.578] (II) fglrx(0): Max Image Size [cm]: horiz.: 48 vert.: 27
[ 2.578] (II) fglrx(0): Gamma: 2.20
[ 2.578] (II) fglrx(0): DPMS capabilities: Off
[ 2.578] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 2.578] (II) fglrx(0): First detailed timing is preferred mode
[ 2.578] (II) fglrx(0): redX: 0.648 redY: 0.339 greenX: 0.143 greenY: 0.070
[ 2.578] (II) fglrx(0): blueX: 0.282 blueY: 0.603 whiteX: 0.312 whiteY: 0.329
[ 2.578] (II) fglrx(0): Supported established timings:
[ 2.578] (II) fglrx(0): 640x480@60Hz
[ 2.578] (II) fglrx(0): 800x600@56Hz
[ 2.578] (II) fglrx(0): 800x600@60Hz
[ 2.578] (II) fglrx(0): 1024x768@60Hz
[ 2.578] (II) fglrx(0): Manufacturer's mask: 0
[ 2.578] (II) fglrx(0): Supported standard timings:
[ 2.578] (II) fglrx(0): #0: hsize: 1280 vsize 800 refresh: 60 vid: 129
[ 2.578] (II) fglrx(0): #1: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 2.578] (II) fglrx(0): #2: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 2.578] (II) fglrx(0): #3: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 2.578] (II) fglrx(0): #4: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 2.578] (II) fglrx(0): #5: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Ranges: V min: 56 V max: 60 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[ 2.578] (II) fglrx(0): Monitor name: SyncMaster
[ 2.578] (II) fglrx(0): Serial No: HMBS500385
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2448 h_sync_end 2492 h_blank_end 2640 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1720 h_sync_end 1760 h_blank_end 1980 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 732 h_sync_end 796 h_blank_end 864 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 576 v_sync: 581 v_sync_end 586 v_blanking: 625 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0
[ 2.578] (II) fglrx(0): Number of EDID sections to follow: 1
[ 2.578] (II) fglrx(0): EDID (in hex):
[ 2.578] (II) fglrx(0): 00ffffffffffff004c2d24053232524c
[ 2.578] (II) fglrx(0): 1413010380301b782a3851a656241248
[ 2.578] (II) fglrx(0): 9a50542308008100814081809500a940
[ 2.578] (II) fglrx(0): b30001010101023a801871382d40582c
[ 2.578] (II) fglrx(0): 4500dd0c1100001e000000fd00383c1e
[ 2.578] (II) fglrx(0): 5111000a202020202020000000fc0053
[ 2.578] (II) fglrx(0): 796e634d61737465720a2020000000ff
[ 2.578] (II) fglrx(0): 00484d42533530303338350a20200168
[ 2.578] (II) fglrx(0): End of Display0 EDID data --------------------
[ 2.578] (II) fglrx(0): EDID for output DFP1
[ 2.578] (II) fglrx(0): EDID for output DFP2
[ 2.578] (II) fglrx(0): EDID for output DFP3
[ 2.578] (II) fglrx(0): EDID for output DFP4
[ 2.578] (II) fglrx(0): EDID for output DFP5
[ 2.578] (II) fglrx(0): EDID for output DFP6
[ 2.578] (II) fglrx(0): EDID for output DFP7
[ 2.578] (II) fglrx(0): EDID for output DFP8
[ 2.578] (II) fglrx(0): EDID for output DFP9
[ 2.578] (II) fglrx(0): EDID for output DFP10
[ 2.578] (II) fglrx(0): Manufacturer: SAM Model: 524 Serial#: 1280455218
[ 2.578] (II) fglrx(0): Year: 2009 Week: 20
[ 2.578] (II) fglrx(0): EDID Version: 1.3
[ 2.578] (II) fglrx(0): Digital Display Input
[ 2.578] (II) fglrx(0): Max Image Size [cm]: horiz.: 48 vert.: 27
[ 2.578] (II) fglrx(0): Gamma: 2.20
[ 2.578] (II) fglrx(0): DPMS capabilities: Off
[ 2.578] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 2.578] (II) fglrx(0): First detailed timing is preferred mode
[ 2.578] (II) fglrx(0): redX: 0.648 redY: 0.339 greenX: 0.143 greenY: 0.070
[ 2.578] (II) fglrx(0): blueX: 0.282 blueY: 0.603 whiteX: 0.312 whiteY: 0.329
[ 2.578] (II) fglrx(0): Supported established timings:
[ 2.578] (II) fglrx(0): 640x480@60Hz
[ 2.578] (II) fglrx(0): 800x600@56Hz
[ 2.578] (II) fglrx(0): 800x600@60Hz
[ 2.578] (II) fglrx(0): 1024x768@60Hz
[ 2.578] (II) fglrx(0): Manufacturer's mask: 0
[ 2.578] (II) fglrx(0): Supported standard timings:
[ 2.578] (II) fglrx(0): #0: hsize: 1280 vsize 800 refresh: 60 vid: 129
[ 2.578] (II) fglrx(0): #1: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 2.578] (II) fglrx(0): #2: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 2.578] (II) fglrx(0): #3: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 2.578] (II) fglrx(0): #4: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 2.578] (II) fglrx(0): #5: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Ranges: V min: 56 V max: 60 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[ 2.578] (II) fglrx(0): Monitor name: SyncMaster
[ 2.578] (II) fglrx(0): Serial No: HMBS500385
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2448 h_sync_end 2492 h_blank_end 2640 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1720 h_sync_end 1760 h_blank_end 1980 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 732 h_sync_end 796 h_blank_end 864 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 576 v_sync: 581 v_sync_end 586 v_blanking: 625 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0
[ 2.578] (II) fglrx(0): Number of EDID sections to follow: 1
[ 2.578] (II) fglrx(0): EDID (in hex):
[ 2.578] (II) fglrx(0): 00ffffffffffff004c2d24053232524c
[ 2.578] (II) fglrx(0): 1413010380301b782a3851a656241248
[ 2.578] (II) fglrx(0): 9a50542308008100814081809500a940
[ 2.578] (II) fglrx(0): b30001010101023a801871382d40582c
[ 2.578] (II) fglrx(0): 4500dd0c1100001e000000fd00383c1e
[ 2.578] (II) fglrx(0): 5111000a202020202020000000fc0053
[ 2.578] (II) fglrx(0): 796e634d61737465720a2020000000ff
[ 2.578] (II) fglrx(0): 00484d42533530303338350a20200168
[ 2.579] (II) fglrx(0): Printing probed modes for output DFP10
[ 2.579] (II) fglrx(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "1920x1080"x50.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1776x1000"x50.0 148.50 1776 2304 2348 2640 1000 1004 1009 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1680x1050"x50.0 148.50 1680 2448 2492 2640 1050 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 2.579] (II) fglrx(0): Modeline "1400x1050"x60.0 162.00 1400 1664 1856 2160 1050 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1400x1050"x50.0 148.50 1400 2448 2492 2640 1050 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1600x900"x60.0 162.00 1600 1664 1856 2160 900 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1600x900"x50.0 148.50 1600 2448 2492 2640 900 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x1024"x50.0 148.50 1280 2448 2492 2640 1024 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1440x900"x50.0 148.50 1440 2448 2492 2640 900 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1440x900"x60.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x960"x50.0 148.50 1280 2448 2492 2640 960 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x800"x50.0 148.50 1280 2448 2492 2640 800 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x800"x60.0 83.50 1280 1352 1480 1680 800 803 809 831 -hsync +vsync (49.7 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x768"x50.0 148.50 1280 2448 2492 2640 768 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x768"x60.0 83.50 1280 1352 1480 1680 768 803 809 831 -hsync +vsync (49.7 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x720"x60.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x720"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "1024x768"x50.0 148.50 1024 2448 2492 2640 768 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 2.579] (II) fglrx(0): Modeline "1152x648"x50.0 74.25 1152 1592 1632 1980 648 653 658 750 +hsync +vsync (37.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "800x600"x50.0 148.50 800 2448 2492 2640 600 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "800x600"x60.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 2.579] (II) fglrx(0): Modeline "800x600"x56.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x576"x60.0 148.50 720 2008 2052 2200 576 1084 1089 1125 +hsync +vsync (67.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x576"x50.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x480"x50.0 148.50 720 2448 2492 2640 480 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x480"x59.9 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "640x480"x50.0 148.50 640 2448 2492 2640 480 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "640x480"x60.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 2.579] (II) fglrx(0): EDID for output CRT1
[ 2.579] (II) fglrx(0): Output DFP1 disconnected
[ 2.579] (II) fglrx(0): Output DFP2 disconnected
[ 2.579] (II) fglrx(0): Output DFP3 disconnected
[ 2.579] (II) fglrx(0): Output DFP4 disconnected
[ 2.579] (II) fglrx(0): Output DFP5 disconnected
[ 2.579] (II) fglrx(0): Output DFP6 disconnected
[ 2.579] (II) fglrx(0): Output DFP7 disconnected
[ 2.579] (II) fglrx(0): Output DFP8 disconnected
[ 2.579] (II) fglrx(0): Output DFP9 disconnected
[ 2.579] (II) fglrx(0): Output DFP10 connected
[ 2.579] (II) fglrx(0): Output CRT1 disconnected
[ 2.579] (II) fglrx(0): Using exact sizes for initial modes
[ 2.579] (II) fglrx(0): Output DFP10 using initial mode 1920x1080
[ 2.579] (II) fglrx(0): DPI set to (96, 96)
[ 2.579] (II) fglrx(0): Eyefinity capable adapter detected.
[ 2.579] (II) fglrx(0): Adapter AMD Radeon HD 7800 Series has 6 configurable heads and 1 displays connected.
[ 2.579] (==) fglrx(0): PseudoColor visuals disabled
[ 2.579] (II) Loading sub module "ramdac"
[ 2.579] (II) LoadModule: "ramdac"
[ 2.579] (II) Module "ramdac" already built-in
[ 2.579] (==) fglrx(0): NoDRI = NO
[ 2.579] (==) fglrx(0): Capabilities: 0x00000000
[ 2.579] (==) fglrx(0): CapabilitiesEx: 0x00000000
[ 2.579] (==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
[ 2.579] (==) fglrx(0): UseFastTLS=0
[ 2.579] (II) fglrx(0): Desktop Vsync is enabled.
[ 2.579] (--) Depth 24 pixmap format is 32 bpp
[ 2.579] (II) Loading extension ATIFGLRXDRI
[ 2.579] (II) fglrx(0): doing swlDriScreenInit
[ 2.579] (II) fglrx(0): swlDriScreenInit for fglrx driver
[ 2.579] ukiDynamicMajor: found major device number 251
[ 2.579] ukiDynamicMajor: found major device number 251
[ 2.579] ukiDynamicMajor: found major device number 251
[ 2.579] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[ 2.579] ukiOpenDevice: node name is /dev/ati/card0
[ 2.579] ukiOpenDevice: open result is 12, (OK)
[ 2.579] ukiOpenByBusid: ukiOpenMinor returns 12
[ 2.579] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[ 2.579] (II) fglrx(0): [uki] DRM interface version 1.0
[ 2.579] (II) fglrx(0): [uki] created "fglrx" driver at busid "PCI:6:0:0"
[ 2.579] (II) fglrx(0): [uki] added 8192 byte SAREA at 0x2000
[ 2.579] (II) fglrx(0): [uki] mapped SAREA 0x2000 to 0x7f1426d74000
[ 2.579] (II) fglrx(0): [uki] framebuffer handle = 0x3000
[ 2.579] (II) fglrx(0): [uki] added 1 reserved context for kernel
[ 2.579] (II) fglrx(0): swlDriScreenInit done
[ 2.579] (II) fglrx(0): Kernel Module Version Information:
[ 2.579] (II) fglrx(0): Name: fglrx
[ 2.579] (II) fglrx(0): Version: 8.98.2
[ 2.579] (II) fglrx(0): Date: Jul 27 2012
[ 2.579] (II) fglrx(0): Desc: AMD FireGL DRM kernel module
[ 2.579] (II) fglrx(0): Kernel Module version matches driver.
[ 2.579] (II) fglrx(0): Kernel Module Build Time Information:
[ 2.579] (II) fglrx(0): Build-Kernel UTS_RELEASE: 3.5.3-1-ARCH
[ 2.579] (II) fglrx(0): Build-Kernel MODVERSIONS: no
[ 2.579] (II) fglrx(0): Build-Kernel __SMP__: no
[ 2.579] (II) fglrx(0): Build-Kernel PAGE_SIZE: 0x1000
[ 2.579] (II) fglrx(0): [uki] register handle = 0x00004000
[ 2.589] (II) fglrx(0): DRI initialization successfull
[ 2.590] (II) fglrx(0): FBADPhys: 0xf400000000 FBMappedSize: 0x010e0000
[ 2.591] (==) fglrx(0): Backing store disabled
[ 2.591] (II) Loading extension FGLRXEXTENSION
[ 2.591] (**) fglrx(0): DPMS enabled
[ 2.591] (II) fglrx(0): Initialized in-driver Xinerama extension
[ 2.591] (**) fglrx(0): Textured Video is enabled.
[ 2.591] (II) LoadModule: "glesx"
[ 2.591] (II) Loading /usr/lib/xorg/modules/glesx.so
[ 2.601] (II) Module glesx: vendor="X.Org Foundation"
[ 2.601] compiled for 1.4.99.906, module version = 1.0.0
[ 2.601] (II) Loading extension GLESX
[ 2.601] (II) fglrx(0): GLESX enableFlags = 592
[ 2.602] (II) fglrx(0): GLESX is enabled
[ 2.602] (II) LoadModule: "amdxmm"
[ 2.602] (II) Loading /usr/lib/xorg/modules/amdxmm.so
[ 2.603] (II) Module amdxmm: vendor="X.Org Foundation"
[ 2.603] compiled for 1.4.99.906, module version = 2.0.0
[ 2.615] (II) Loading extension AMDXVOPL
[ 2.615] (II) Loading extension AMDXVBA
[ 2.617] (II) fglrx(0): UVD feature is enabled(II) fglrx(0):
[ 2.618] (II) fglrx(0): Enable composite support successfully
[ 2.618] (WW) fglrx(0): Option "VendorName" is not used
[ 2.618] (WW) fglrx(0): Option "ModelName" is not used
[ 2.618] (II) fglrx(0): X context handle = 0x1
[ 2.618] (II) fglrx(0): [DRI] installation complete
[ 2.618] (==) fglrx(0): Silken mouse enabled
[ 2.618] (==) fglrx(0): Using HW cursor of display infrastructure!
[ 2.618] (II) fglrx(0): Disabling in-server RandR and enabling in-driver RandR 1.2.
[ 2.735] (II) fglrx(0): Framebuffer compression enabled: mcAddr=0xf407a40000 width=0xa00 height=0x3267
[ 2.735] (--) RandR disabled
[ 2.735] (II) Initializing built-in extension Generic Event Extension
[ 2.735] (II) Initializing built-in extension SHAPE
[ 2.735] (II) Initializing built-in extension MIT-SHM
[ 2.735] (II) Initializing built-in extension XInputExtension
[ 2.735] (II) Initializing built-in extension XTEST
[ 2.735] (II) Initializing built-in extension BIG-REQUESTS
[ 2.735] (II) Initializing built-in extension SYNC
[ 2.735] (II) Initializing built-in extension XKEYBOARD
[ 2.735] (II) Initializing built-in extension XC-MISC
[ 2.735] (II) Initializing built-in extension SECURITY
[ 2.735] (II) Initializing built-in extension XINERAMA
[ 2.735] (II) Initializing built-in extension XFIXES
[ 2.735] (II) Initializing built-in extension RENDER
[ 2.735] (II) Initializing built-in extension RANDR
[ 2.735] (II) Initializing built-in extension COMPOSITE
[ 2.735] (II) Initializing built-in extension DAMAGE
[ 2.736] ukiDynamicMajor: found major device number 251
[ 2.736] ukiDynamicMajor: found major device number 251
[ 2.736] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[ 2.736] ukiOpenDevice: node name is /dev/ati/card0
[ 2.736] ukiOpenDevice: open result is 13, (OK)
[ 2.736] ukiOpenByBusid: ukiOpenMinor returns 13
[ 2.736] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[ 2.842] (II) AIGLX: Loaded and initialized OpenGL driver(II) GLX: Initialized DRI GL provider for screen 0
[ 2.857] (II) fglrx(0): Enable the clock gating!
[ 2.872] (II) fglrx(0): Desktop Vsync is enabled.
[ 2.872] (II) fglrx(0): Setting screen physical size to 508 x 285
[ 2.901] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 2.901] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 2.901] (II) LoadModule: "evdev"
[ 2.901] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2.902] (II) Module evdev: vendor="X.Org Foundation"
[ 2.902] compiled for 1.12.3.901, module version = 2.7.3
[ 2.902] Module class: X.Org XInput Driver
[ 2.902] ABI class: X.Org XInput driver, version 16.0
[ 2.902] (II) Using input driver 'evdev' for 'Power Button'
[ 2.902] (**) Power Button: always reports core events
[ 2.902] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 2.902] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 2.902] (--) evdev: Power Button: Found keys
[ 2.902] (II) evdev: Power Button: Configuring as keyboard
[ 2.902] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[ 2.902] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 2.902] (**) Option "xkb_rules" "evdev"
[ 2.902] (**) Option "xkb_model" "evdev"
[ 2.902] (**) Option "xkb_layout" "us"
[ 2.902] (**) Option "xkb_variant" "dvp"
[ 2.913] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 2.913] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 2.913] (II) Using input driver 'evdev' for 'Power Button'
[ 2.913] (**) Power Button: always reports core events
[ 2.913] (**) evdev: Power Button: Device: "/dev/input/event1"
[ 2.913] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 2.913] (--) evdev: Power Button: Found keys
[ 2.913] (II) evdev: Power Button: Configuring as keyboard
[ 2.913] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1/event1"
[ 2.913] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 2.913] (**) Option "xkb_rules" "evdev"
[ 2.913] (**) Option "xkb_model" "evdev"
[ 2.913] (**) Option "xkb_layout" "us"
[ 2.913] (**) Option "xkb_variant" "dvp"
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=11 (/dev/input/event14)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=10 (/dev/input/event15)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=9 (/dev/input/event16)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=8 (/dev/input/event17)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=7 (/dev/input/event18)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=3 (/dev/input/event19)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Surround (/dev/input/event10)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Front (/dev/input/event11)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event4)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event5)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event6)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event7)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Side (/dev/input/event8)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out CLFE (/dev/input/event9)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event12)
[ 2.914] (**) Logitech USB Receiver: Applying InputClass "evdev pointer catchall"
[ 2.914] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[ 2.914] (**) Logitech USB Receiver: always reports core events
[ 2.914] (**) evdev: Logitech USB Receiver: Device: "/dev/input/event12"
[ 2.914] (--) evdev: Logitech USB Receiver: Vendor 0x46d Product 0xc52f
[ 2.914] (--) evdev: Logitech USB Receiver: Found 20 mouse buttons
[ 2.914] (--) evdev: Logitech USB Receiver: Found scroll wheel(s)
[ 2.914] (--) evdev: Logitech USB Receiver: Found relative axes
[ 2.914] (--) evdev: Logitech USB Receiver: Found x and y relative axes
[ 2.914] (II) evdev: Logitech USB Receiver: Configuring as mouse
[ 2.914] (II) evdev: Logitech USB Receiver: Adding scrollwheel support
[ 2.914] (**) evdev: Logitech USB Receiver: YAxisMapping: buttons 4 and 5
[ 2.914] (**) evdev: Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 2.914] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.7/4-1.7:1.0/input/input12/event12"
[ 2.914] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: MOUSE, id 8)
[ 2.914] (II) evdev: Logitech USB Receiver: initialized for relative axes.
[ 2.915] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration profile 0
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[ 2.915] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/mouse0)
[ 2.915] (II) No input driver specified, ignoring this device.
[ 2.915] (II) This device may have been added with another device file.
[ 2.915] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event13)
[ 2.915] (**) Logitech USB Receiver: Applying InputClass "evdev keyboard catchall"
[ 2.915] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[ 2.915] (**) Logitech USB Receiver: always reports core events
[ 2.915] (**) evdev: Logitech USB Receiver: Device: "/dev/input/event13"
[ 2.915] (--) evdev: Logitech USB Receiver: Vendor 0x46d Product 0xc52f
[ 2.915] (--) evdev: Logitech USB Receiver: Found 1 mouse buttons
[ 2.915] (--) evdev: Logitech USB Receiver: Found scroll wheel(s)
[ 2.915] (--) evdev: Logitech USB Receiver: Found relative axes
[ 2.915] (II) evdev: Logitech USB Receiver: Forcing relative x/y axes to exist.
[ 2.915] (--) evdev: Logitech USB Receiver: Found absolute axes
[ 2.915] (II) evdev: Logitech USB Receiver: Forcing absolute x/y axes to exist.
[ 2.915] (--) evdev: Logitech USB Receiver: Found keys
[ 2.915] (II) evdev: Logitech USB Receiver: Configuring as mouse
[ 2.915] (II) evdev: Logitech USB Receiver: Configuring as keyboard
[ 2.915] (II) evdev: Logitech USB Receiver: Adding scrollwheel support
[ 2.915] (**) evdev: Logitech USB Receiver: YAxisMapping: buttons 4 and 5
[ 2.915] (**) evdev: Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 2.915] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.7/4-1.7:1.1/input/input13/event13"
[ 2.915] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: KEYBOARD, id 9)
[ 2.915] (**) Option "xkb_rules" "evdev"
[ 2.915] (**) Option "xkb_model" "evdev"
[ 2.915] (**) Option "xkb_layout" "us"
[ 2.915] (**) Option "xkb_variant" "dvp"
[ 2.915] (II) evdev: Logitech USB Receiver: initialized for relative axes.
[ 2.915] (WW) evdev: Logitech USB Receiver: ignoring absolute axes.
[ 2.915] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration profile 0
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[ 2.915] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 2.915] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 2.915] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 2.915] (**) AT Translated Set 2 keyboard: always reports core events
[ 2.915] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 2.915] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 2.915] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 2.915] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 2.915] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 2.915] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 10)
[ 2.915] (**) Option "xkb_rules" "evdev"
[ 2.915] (**) Option "xkb_model" "evdev"
[ 2.915] (**) Option "xkb_layout" "us"
[ 2.915] (**) Option "xkb_variant" "dvp"
[ 2.915] (II) config/udev: Adding input device PC Speaker (/dev/input/event3)
[ 2.915] (II) No input driver specified, ignoring this device.
[ 2.915] (II) This device may have been added with another device file.
[ 2.917] (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments
[ 7.513] (II) fglrx(0): EDID vendor "SAM", prod id 1316
[ 7.513] (II) fglrx(0): Using EDID range info for horizontal sync
[ 7.513] (II) fglrx(0): Using EDID range info for vertical refresh
[ 7.513] (II) fglrx(0): Printing DDC gathered Modelines:
[ 7.513] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 7.513] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "720x576"x0.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz e)
[ 7.513] (II) fglrx(0): Modeline "720x480"x0.0 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 7.513] (II) fglrx(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 7.513] (II) fglrx(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x800"x0.0 71.00 1280 1328 1360 1440 800 803 809 823 +hsync -vsync (49.3 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
[ 10.738] (II) fglrx(0): EDID vendor "SAM", prod id 1316
[ 10.738] (II) fglrx(0): Using hsync ranges from config file
[ 10.738] (II) fglrx(0): Using vrefresh ranges from config file
[ 10.738] (II) fglrx(0): Printing DDC gathered Modelines:
[ 10.738] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 10.738] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "720x576"x0.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz e)
[ 10.738] (II) fglrx(0): Modeline "720x480"x0.0 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 10.738] (II) fglrx(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 10.738] (II) fglrx(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x800"x0.0 71.00 1280 1328 1360 1440 800 803 809 823 +hsync -vsync (49.3 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
Here's the Xorg.conf:
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
BusID "PCI:6:0:0"
Option "OpenGLOverlay" "0"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
Monitor "aticonfig-Monitor[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
Setting the PCI BusID in Xorg.conf seems to have no effect, even if I set it to 6:0:0 or 7:0:0, its still the same.
Do I need to set AutoAddDevices off?

MisterAnderson wrote:Does the same happen with the opensource radeon drivers? (xf86-video-ati)
Thanks for the reply!
The open source driver doesn't support my card yet. I tried installing it first since its the recommended driver, but Xorg couldn't detect any display at all.
It seems the PCI BusID is not being read from the xorg.conf file. There's auto detection everytime the PC boots.
Last edited by hdhiman (2012-10-04 00:43:52)

Secondary display not detected on cold boot, nvidia

So since a week or two i have this strange problem that if i want to activate my secondary monitor(a beamer is plugged into it) nvidia doesn't find it. If i reboot my pc it works without any problems, restarting X doesn't solve the problem as well.
I usually use disper to do the job, but also in nvidia-settings the display isn't detected or shown.
My card is a nvidia 8800gt, my xorg.conf is just empty and i'm using 260.19.29-1 drivers, recent Xorg version and system is generally up to date.
Any hints where i can look for errors? dmesg didn't give me any usefull information, but i will quote it anyway, maybe you gues can see something in it.
thanks in advanced!
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.36-ARCH (tobias@T-POWA-LX) (gcc version 4.5.2 (GCC) ) #1 SMP PREEMPT Sat Jan 8 14:15:27 CET 2011
Command line: root=/dev/disk/by-uuid/1b22407b-2469-4b20-b0c2-5a709eaaccad ro vga=773
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ff80000 (usable)
BIOS-e820: 000000007ff80000 - 000000007ff8e000 (ACPI data)
BIOS-e820: 000000007ff8e000 - 000000007ffe0000 (ACPI NVS)
BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
NX (Execute Disable) protection: active
DMI 2.4 present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
No AGP bridge found
last_pfn = 0x7ff80 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-DFFFF write-protect
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 disabled
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009fc00 (usable)
modified: 000000000009fc00 - 00000000000a0000 (reserved)
modified: 00000000000e4000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 000000007ff80000 (usable)
modified: 000000007ff80000 - 000000007ff8e000 (ACPI data)
modified: 000000007ff8e000 - 000000007ffe0000 (ACPI NVS)
modified: 000000007ffe0000 - 0000000080000000 (reserved)
modified: 00000000fee00000 - 00000000fee01000 (reserved)
modified: 00000000fff00000 - 0000000100000000 (reserved)
initial memory mapped : 0 - 20000000
found SMP MP-table at [ffff8800000ff780] ff780
init_memory_mapping: 0000000000000000-000000007ff80000
0000000000 - 007fe00000 page 2M
007fe00000 - 007ff80000 page 4k
kernel direct mapping tables up to 7ff80000 @ 16000-1a000
RAMDISK: 37dea000 - 37ff0000
ACPI: RSDP 00000000000fbcd0 00014 (v00 ACPIAM)
ACPI: RSDT 000000007ff80000 0003C (v01 A_M_I_ OEMRSDT 10000814 MSFT 00000097)
ACPI: FACP 000000007ff80200 00084 (v02 A_M_I_ OEMFACP 10000814 MSFT 00000097)
ACPI: DSDT 000000007ff80440 090AA (v01 A0751 A0751077 00000077 INTL 20060113)
ACPI: FACS 000000007ff8e000 00040
ACPI: APIC 000000007ff80390 0006C (v01 A_M_I_ OEMAPIC 10000814 MSFT 00000097)
ACPI: MCFG 000000007ff80400 0003C (v01 A_M_I_ OEMMCFG 10000814 MSFT 00000097)
ACPI: OEMB 000000007ff8e040 00081 (v01 A_M_I_ AMI_OEM 10000814 MSFT 00000097)
ACPI: HPET 000000007ff894f0 00038 (v01 A_M_I_ OEMHPET 10000814 MSFT 00000097)
ACPI: OSFR 000000007ff89530 000B0 (v01 A_M_I_ OEMOSFR 10000814 MSFT 00000097)
ACPI: Local APIC address 0xfee00000
[ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880002000000-ffff880003bfffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal empty
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0007ff80
On node 0 totalpages: 524047
DMA zone: 56 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3927 pages, LIFO batch:0
DMA32 zone: 7111 pages used for memmap
DMA32 zone: 512953 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a301 base: 0xfed00000
SMP: Allowing 4 CPUs, 2 hotplug CPUs
nr_irqs_gsi: 40
early_res array is doubled to 64 at [18180 - 1897f]
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 80000000:7ee00000)
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 28 pages/cpu @ffff880001a00000 s86016 r8192 d20480 u524288
pcpu-alloc: s86016 r8192 d20480 u524288 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 516880
Kernel command line: root=/dev/disk/by-uuid/1b22407b-2469-4b20-b0c2-5a709eaaccad ro vga=773
PID hash table entries: 4096 (order: 3, 32768 bytes)
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Subtract (49 early reservations)
#1 [0001000000 - 00017fc9a8] TEXT DATA BSS
#2 [0037dea000 - 0037ff0000] RAMDISK
#3 [00017fd000 - 00017fd270] BRK
#4 [00000ff790 - 0000100000] BIOS reserved
#5 [00000ff780 - 00000ff790] MP-table mpf
#6 [000009fc00 - 00000f1540] BIOS reserved
#7 [00000f16b4 - 00000ff780] BIOS reserved
#8 [00000f1540 - 00000f16b4] MP-table mpc
#9 [0000010000 - 0000012000] TRAMPOLINE
#10 [0000012000 - 0000016000] ACPI WAKEUP
#11 [0000016000 - 0000018000] PGTABLE
#12 [00017fd280 - 00017fe280] BOOTMEM
#13 [0000018000 - 0000018180] BOOTMEM
#14 [0001fff000 - 0002000000] BOOTMEM
#15 [0004000000 - 0004001000] BOOTMEM
#16 [0002000000 - 0003c00000] MEMMAP 0
#17 [00017fe280 - 0001816280] BOOTMEM
#18 [0001816280 - 000182e280] BOOTMEM
#19 [000182f000 - 0001830000] BOOTMEM
#20 [00017fc9c0 - 00017fca01] BOOTMEM
#21 [00017fca40 - 00017fca83] BOOTMEM
#22 [00017fcac0 - 00017fccf0] BOOTMEM
#23 [00017fcd00 - 00017fcd68] BOOTMEM
#24 [00017fcd80 - 00017fcde8] BOOTMEM
#25 [00017fce00 - 00017fce68] BOOTMEM
#26 [00017fce80 - 00017fcee8] BOOTMEM
#27 [00017fcf00 - 00017fcf68] BOOTMEM
#28 [00017fcf80 - 00017fcfe8] BOOTMEM
#29 [000182e280 - 000182e2e8] BOOTMEM
#30 [000182e300 - 000182e368] BOOTMEM
#31 [000182e380 - 000182e3e8] BOOTMEM
#32 [000182e400 - 000182e420] BOOTMEM
#33 [000182e440 - 000182e487] BOOTMEM
#34 [000182e4c0 - 000182e507] BOOTMEM
#35 [0001a00000 - 0001a1c000] BOOTMEM
#36 [0001a80000 - 0001a9c000] BOOTMEM
#37 [0001b00000 - 0001b1c000] BOOTMEM
#38 [0001b80000 - 0001b9c000] BOOTMEM
#39 [000182e540 - 000182e548] BOOTMEM
#40 [000182e580 - 000182e588] BOOTMEM
#41 [000182e5c0 - 000182e5d0] BOOTMEM
#42 [000182e600 - 000182e620] BOOTMEM
#43 [000182e640 - 000182e770] BOOTMEM
#44 [000182e780 - 000182e7d0] BOOTMEM
#45 [000182e800 - 000182e850] BOOTMEM
#46 [0001830000 - 0001838000] BOOTMEM
#47 [0001b9c000 - 0001d9c000] BOOTMEM
#48 [0001838000 - 0001938000] BOOTMEM
Memory: 2053464k/2096640k available (3685k kernel code, 452k absent, 42724k reserved, 2088k data, 508k init)
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:2304
Console: colour dummy device 80x25
console [tty0] enabled
allocated 20971520 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
hpet clockevent registered
Fast TSC calibration using PIT
Detected 3005.698 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 6013.87 BogoMIPS (lpj=10018993)
pid_max: default: 32768 minimum: 301
Security Framework initialized
TOMOYO Linux initialized
AppArmor: AppArmor disabled by boot time parameter
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys blkio
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
PEBS disabled due to CPU errata.
... version: 2
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
ACPI: Core revision 20100702
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz stepping 0b
NMI watchdog enabled, takes one hw-pmu counter.
Booting Node 0, Processors #1
NMI watchdog enabled, takes one hw-pmu counter.
Brought up 2 CPUs
Total of 2 processors activated (12027.40 BogoMIPS).
devtmpfs: initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: not using MMCONFIG
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: SSDT 000000007ff8e0d0 001D2 (v01 AMI CPU1PM 00000001 INTL 20060113)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 001D2 (v01 AMI CPU1PM 00000001 INTL 20060113)
ACPI: SSDT 000000007ff8e2b0 00143 (v01 AMI CPU2PM 00000001 INTL 20060113)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00143 (v01 AMI CPU2PM 00000001 INTL 20060113)
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
ACPI: No dock devices found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000dffff]
pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xffffffff]
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:1a.0: reg 20: [io 0xb800-0xb81f]
pci 0000:00:1a.1: reg 20: [io 0xb880-0xb89f]
pci 0000:00:1a.2: reg 20: [io 0xbc00-0xbc1f]
pci 0000:00:1a.7: reg 10: [mem 0xf9fffc00-0xf9ffffff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10: [mem 0xf9ff8000-0xf9ffbfff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
pci 0000:00:1d.0: reg 20: [io 0xb080-0xb09f]
pci 0000:00:1d.1: reg 20: [io 0xb400-0xb41f]
pci 0000:00:1d.2: reg 20: [io 0xb480-0xb49f]
pci 0000:00:1d.7: reg 10: [mem 0xf9fff800-0xf9fffbff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
pci 0000:00:1f.2: reg 10: [io 0xa000-0xa007]
pci 0000:00:1f.2: reg 14: [io 0x9c00-0x9c03]
pci 0000:00:1f.2: reg 18: [io 0x9880-0x9887]
pci 0000:00:1f.2: reg 1c: [io 0x9800-0x9803]
pci 0000:00:1f.2: reg 20: [io 0x9480-0x948f]
pci 0000:00:1f.2: reg 24: [io 0x9400-0x940f]
pci 0000:00:1f.3: reg 10: [mem 0xf9fff400-0xf9fff4ff 64bit]
pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]
pci 0000:00:1f.5: reg 10: [io 0xb000-0xb007]
pci 0000:00:1f.5: reg 14: [io 0xac00-0xac03]
pci 0000:00:1f.5: reg 18: [io 0xa880-0xa887]
pci 0000:00:1f.5: reg 1c: [io 0xa800-0xa803]
pci 0000:00:1f.5: reg 20: [io 0xa480-0xa48f]
pci 0000:00:1f.5: reg 24: [io 0xa400-0xa40f]
pci 0000:01:00.0: reg 10: [mem 0xfd000000-0xfdffffff]
pci 0000:01:00.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:01:00.0: reg 1c: [mem 0xfa000000-0xfbffffff 64bit]
pci 0000:01:00.0: reg 24: [io 0xcc00-0xcc7f]
pci 0000:01:00.0: reg 30: [mem 0xfe8e0000-0xfe8fffff pref]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfe8fffff]
pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 04-04]
pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
pci 0000:00:1c.0: bridge window [mem 0xf8f00000-0xf8ffffff 64bit pref]
pci 0000:03:00.0: reg 24: [mem 0xfeafe000-0xfeafffff]
pci 0000:03:00.0: reg 30: [mem 0xfeae0000-0xfeaeffff pref]
pci 0000:03:00.0: PME# supported from D3hot
pci 0000:03:00.0: PME# disabled
pci 0000:03:00.1: reg 10: [io 0xdc00-0xdc07]
pci 0000:03:00.1: reg 14: [io 0xd880-0xd883]
pci 0000:03:00.1: reg 18: [io 0xd800-0xd807]
pci 0000:03:00.1: reg 1c: [io 0xd480-0xd483]
pci 0000:03:00.1: reg 20: [io 0xd400-0xd40f]
pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.4: PCI bridge to [bus 03-03]
pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
pci 0000:00:1c.4: bridge window [mem 0xfea00000-0xfeafffff]
pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:02:00.0: reg 10: [mem 0xfe9c0000-0xfe9fffff 64bit]
pci 0000:02:00.0: reg 30: [mem 0xfe9a0000-0xfe9bffff pref]
pci 0000:02:00.0: PME# supported from D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
pci 0000:00:1c.5: PCI bridge to [bus 02-02]
pci 0000:00:1c.5: bridge window [io 0xf000-0x0000] (disabled)
pci 0000:00:1c.5: bridge window [mem 0xfe900000-0xfe9fffff]
pci 0000:00:1c.5: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:05:02.0: reg 10: [mem 0xfebf8000-0xfebfffff]
pci 0000:05:03.0: reg 10: [mem 0xfebf7800-0xfebf7fff]
pci 0000:05:03.0: reg 14: [io 0xec00-0xec7f]
pci 0000:05:03.0: supports D2
pci 0000:05:03.0: PME# supported from D2 D3hot D3cold
pci 0000:05:03.0: PME# disabled
pci 0000:00:1e.0: PCI bridge to [bus 05-05] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff]
pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x80000000-0xffffffff] (subtractive decode)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
HEST: Table is not found!
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 000000000009fc00 - 000000000009ffff
reserve RAM buffer: 000000007ff80000 - 000000007fffffff
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
HPET: 4 timers in total, 0 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 comparators, 64-bit 14.318180 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: [mem 0xfed14000-0xfed19fff] has been reserved
system 00:07: [io 0x0290-0x0297] has been reserved
system 00:08: [io 0x04d0-0x04d1] has been reserved
system 00:08: [io 0x0800-0x087f] has been reserved
system 00:08: [io 0x0480-0x04bf] has been reserved
system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
system 00:08: [mem 0xfed50000-0xfed8ffff] has been reserved
system 00:08: [mem 0xffa00000-0xffafffff] has been reserved
system 00:08: [mem 0xffb00000-0xffbfffff] has been reserved
system 00:08: [mem 0xffe00000-0xffefffff] has been reserved
system 00:08: [mem 0xfff00000-0xfffffffe] has been reserved
system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved
system 00:0d: [mem 0xe0000000-0xefffffff] has been reserved
system 00:0e: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:0e: [mem 0x000c0000-0x000cffff] has been reserved
system 00:0e: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:0e: [mem 0x00100000-0x7fffffff] could not be reserved
pci 0000:00:1c.0: BAR 14: assigned [mem 0x80000000-0x803fffff]
pci 0000:00:1c.4: BAR 15: assigned [mem 0x80400000-0x805fffff 64bit pref]
pci 0000:00:1c.5: BAR 15: assigned [mem 0x80600000-0x807fffff 64bit pref]
pci 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
pci 0000:00:1c.5: BAR 13: assigned [io 0x2000-0x2fff]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfe8fffff]
pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:00:1c.0: PCI bridge to [bus 04-04]
pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
pci 0000:00:1c.0: bridge window [mem 0x80000000-0x803fffff]
pci 0000:00:1c.0: bridge window [mem 0xf8f00000-0xf8ffffff 64bit pref]
pci 0000:00:1c.4: PCI bridge to [bus 03-03]
pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
pci 0000:00:1c.4: bridge window [mem 0xfea00000-0xfeafffff]
pci 0000:00:1c.4: bridge window [mem 0x80400000-0x805fffff 64bit pref]
pci 0000:00:1c.5: PCI bridge to [bus 02-02]
pci 0000:00:1c.5: bridge window [io 0x2000-0x2fff]
pci 0000:00:1c.5: bridge window [mem 0xfe900000-0xfe9fffff]
pci 0000:00:1c.5: bridge window [mem 0x80600000-0x807fffff 64bit pref]
pci 0000:00:1e.0: PCI bridge to [bus 05-05]
pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff]
pci 0000:00:1e.0: bridge window [mem pref disabled]
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: enabling device (0106 -> 0107)
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1c.5: enabling device (0106 -> 0107)
pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.5: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
pci_bus 0000:00: resource 8 [mem 0x80000000-0xffffffff]
pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
pci_bus 0000:01: resource 1 [mem 0xfa000000-0xfe8fffff]
pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
pci_bus 0000:04: resource 0 [io 0x1000-0x1fff]
pci_bus 0000:04: resource 1 [mem 0x80000000-0x803fffff]
pci_bus 0000:04: resource 2 [mem 0xf8f00000-0xf8ffffff 64bit pref]
pci_bus 0000:03: resource 0 [io 0xd000-0xdfff]
pci_bus 0000:03: resource 1 [mem 0xfea00000-0xfeafffff]
pci_bus 0000:03: resource 2 [mem 0x80400000-0x805fffff 64bit pref]
pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:02: resource 1 [mem 0xfe900000-0xfe9fffff]
pci_bus 0000:02: resource 2 [mem 0x80600000-0x807fffff 64bit pref]
pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
pci_bus 0000:05: resource 1 [mem 0xfeb00000-0xfebfffff]
pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:05: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:05: resource 7 [mem 0x000d0000-0x000dffff]
pci_bus 0000:05: resource 8 [mem 0x80000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
UDP hash table entries: 1024 (order: 3, 32768 bytes)
UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
NET: Registered protocol family 1
pci 0000:01:00.0: Boot video device
PCI: CLS 32 bytes, default 64
Unpacking initramfs...
Freeing initrd memory: 2072k freed
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1295539103.273:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 4014
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
vesafb: framebuffer at 0xfb000000, mapped to 0xffffc90010100000, using 1536k, total 14336k
vesafb: mode is 1024x768x8, linelength=1024, pages=3
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
intel_idle: MWAIT substates: 0x220
intel_idle: does not run on family 6 model 15
ERST: Table is not found!
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Registering the dns_resolver key type
PM: Resume from disk failed.
registered taskstats version 1
rtc_cmos 00:03: setting system clock to 2011-01-20 15:58:24 UTC (1295539104)
Initalizing network drop monitor service
Freeing unused kernel memory: 508k freed
udev[38]: starting version 165
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.2: version 2.13
ata_piix 0000:00:1f.2: PCI INT B -> GSI 22 (level, low) -> IRQ 22
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001)
pata_jmicron 0000:03:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pata_jmicron 0000:03:00.1: setting latency timer to 64
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi0 : pata_jmicron
scsi1 : ata_piix
Floppy drive(s): fd0 is 1.44M
scsi2 : pata_jmicron
ata1: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 17
ata2: PATA max UDMA/100 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 17
FDC 0 is a post-1991 82077
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 22
ata4: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 22
ata_piix 0000:00:1f.5: PCI INT B -> GSI 22 (level, low) -> IRQ 22
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
ata_piix 0000:00:1f.5: setting latency timer to 64
scsi4 : ata_piix
scsi5 : ata_piix
ata5: SATA max UDMA/133 cmd 0xb000 ctl 0xac00 bmdma 0xa480 irq 22
ata6: SATA max UDMA/133 cmd 0xa880 ctl 0xa800 bmdma 0xa488 irq 22
ata1.01: HPA detected: current 156365903, native 156368016
ata1.01: ATA-7: SAMSUNG SP0802N, TK100-31, max UDMA/100
ata1.01: 156365903 sectors, multi 0: LBA48
ata1.01: limited to UDMA/33 due to 40-wire cable
ata1.01: configured for UDMA/33
scsi 0:0:1:0: Direct-Access ATA SAMSUNG SP0802N TK10 PQ: 0 ANSI: 5
ata6: SATA link down (SStatus 0 SControl 300)
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: TSSTcorpDVD-ROM SH-D163B, SB01, max UDMA/33
ata3.00: ATA-7: SAMSUNG HA250JC, WE100-33, max UDMA/133
ata3.00: 488397168 sectors, multi 16: LBA48
ata3.00: applying bridge limits
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/33
ata5.00: ATA-7: SAMSUNG HD103UJ, 1AA01113, max UDMA7
ata5.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/100
scsi 1:0:0:0: Direct-Access ATA SAMSUNG HA250JC WE10 PQ: 0 ANSI: 5
ata5.00: configured for UDMA/133
scsi 3:0:0:0: CD-ROM TSSTcorp DVD-ROM SH-D163B SB01 PQ: 0 ANSI: 5
scsi 4:0:0:0: Direct-Access ATA SAMSUNG HD103UJ 1AA0 PQ: 0 ANSI: 5
ahci 0000:03:00.0: version 3.0
ahci 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
sd 0:0:1:0: [sda] 156365903 512-byte logical blocks: (80.0 GB/74.5 GiB)
sd 0:0:1:0: [sda] Write Protect is off
sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 4:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 4:0:0:0: [sdc] Write Protect is off
sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part
ahci 0000:03:00.0: setting latency timer to 64
scsi6 : ahci
scsi7 : ahci
ata7: SATA max UDMA/133 abar m8192@0xfeafe000 port 0xfeafe100 irq 16
ata8: SATA max UDMA/133 abar m8192@0xfeafe000 port 0xfeafe180 irq 16
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 4:0:0:0: [sdc] Attached SCSI disk
sd 0:0:1:0: [sda] Attached SCSI disk
sdb: sdb1 sdb2 sdb3 sdb4
sd 1:0:0:0: [sdb] Attached SCSI disk
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
sr0: scsi3-mmc drive: 4x/48x cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: (null)
Not activating Mandatory Access Control now since /sbin/tomoyo-init doesn't exist.
udev[854]: starting version 165
ACPI: acpi_idle registered with cpuidle
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
input: PC Speaker as /devices/platform/pcspkr/input/input2
sd 0:0:1:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sr 3:0:0:0: Attached scsi generic sg2 type 5
sd 4:0:0:0: Attached scsi generic sg3 type 0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9fffc00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9fff800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
iTCO_vendor_support: vendor-support=0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000b800
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000b880
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1a.2: setting latency timer to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000bc00
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b080
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b400
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b480
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ACPI: resource 0000:00:1f.3 [io 0x0400-0x041f] conflicts with ACPI region SMRG [io 0x0400-0x040f 64bit pref disabled]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
cfg80211: Calling CRDA to update world regulatory domain
usb 1-5: new high speed USB device using ehci_hcd and address 4
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
rt61pci 0000:05:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
HDA Intel 0000:00:1b.0: irq 40 for MSI/MSI-X
HDA Intel 0000:00:1b.0: setting latency timer to 64
phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: rt61pci-phy0::radio
Registered led device: rt61pci-phy0::assoc
firewire_ohci 0000:05:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
firewire_ohci: Added fw-ohci device 0000:05:03.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x11
usb 4-1: new full speed USB device using uhci_hcd and address 2
Initializing USB Mass Storage driver...
scsi8 : usb-storage 1-5:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
hda_codec: ALC883: BIOS auto-probing.
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input3
atl1 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
atl1 0000:02:00.0: setting latency timer to 64
atl1 0000:02:00.0: version 2.1.3
usbcore: registered new interface driver snd-usb-audio
usb 4-2: new low speed USB device using uhci_hcd and address 3
firewire_core: created device fw0: GUID 001e8c000007fb14, S400
usbcore: registered new interface driver hiddev
input: Logitech Logitech USB Keyboard as /devices/pci0000:00/0000:00:1a.1/usb4/4-2/4-2:1.0/input/input4
generic-usb 0003:046D:C316.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:1a.1-2/input0
input: Logitech Logitech USB Keyboard as /devices/pci0000:00/0000:00:1a.1/usb4/4-2/4-2:1.1/input/input5
generic-usb 0003:046D:C316.0002: input,hidraw1: USB HID v1.10 Device [Logitech Logitech USB Keyboard] on usb-0000:00:1a.1-2/input1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usb 5-2: new low speed USB device using uhci_hcd and address 2
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
scsi 8:0:0:0: Direct-Access WD My Book 1110 2003 PQ: 0 ANSI: 4
sd 8:0:0:0: Attached scsi generic sg4 type 0
scsi 8:0:0:1: CD-ROM WD Virtual CD 1110 2003 PQ: 0 ANSI: 4
sd 8:0:0:0: [sdd] 3905656832 512-byte logical blocks: (1.99 TB/1.81 TiB)
sd 8:0:0:0: [sdd] Write Protect is off
sd 8:0:0:0: [sdd] Mode Sense: 23 00 10 00
sd 8:0:0:0: [sdd] Assuming drive cache: write through
sr1: scsi3-mmc drive: 51x/51x caddy
sr 8:0:0:1: Attached scsi CD-ROM sr1
sr 8:0:0:1: Attached scsi generic sg5 type 5
scsi 8:0:0:2: Enclosure WD SES Device 2003 PQ: 0 ANSI: 4
scsi 8:0:0:2: Attached scsi generic sg6 type 13
sd 8:0:0:0: [sdd] Assuming drive cache: write through
sdd: sdd1
sd 8:0:0:0: [sdd] Assuming drive cache: write through
sd 8:0:0:0: [sdd] Attached SCSI disk
input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.2/usb5/5-2/5-2:1.0/input/input6
generic-usb 0003:046D:C051.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.2-2/input0
ses 8:0:0:2: Attached Enclosure device
usb 7-1: new full speed USB device using uhci_hcd and address 2
nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 260.19.29 Wed Dec 8 12:08:56 PST 2010
input: Xbox 360 Wireless Receiver as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1:1.0/input/input7
input: Xbox 360 Wireless Receiver as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1:1.2/input/input8
input: Xbox 360 Wireless Receiver as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1:1.4/input/input9
input: Xbox 360 Wireless Receiver as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1:1.6/input/input10
usbcore: registered new interface driver xpad
xpad: X-Box pad driver
EXT4-fs (sdb3): re-mounted. Opts: (null)
EXT4-fs (sdb3): re-mounted. Opts: (null)
EXT4-fs (sdb4): mounted filesystem with ordered data mode. Opts: (null)
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (sdc1): using internal journal
EXT3-fs (sdc1): mounted filesystem with writeback data mode
Adding 4096568k swap on /dev/sdb2. Priority:-1 extents:1 across:4096568k
atl1 0000:02:00.0: irq 41 for MSI/MSI-X
atl1 0000:02:00.0: eth0 link is up 100 Mbps full duplex
start_kdeinit (2156): /proc/2156/oom_adj is deprecated, please use /proc/2156/oom_score_adj instead.
EXT4-fs (sdb3): re-mounted. Opts: commit=0
EXT4-fs (sdb4): re-mounted. Opts: commit=0
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
lo: Disabled Privacy Extensions
process `skype' is using obsolete setsockopt SO_BSDCOMPAT
lo: Disabled Privacy Extensions
Last edited by ichbinesderelch (2011-01-20 17:05:51)

MisterAnderson wrote:Does the same happen with the opensource radeon drivers? (xf86-video-ati)
Thanks for the reply!
The open source driver doesn't support my card yet. I tried installing it first since its the recommended driver, but Xorg couldn't detect any display at all.
It seems the PCI BusID is not being read from the xorg.conf file. There's auto detection everytime the PC boots.
Last edited by hdhiman (2012-10-04 00:43:52)

Neo4 Platinum failed to cold boot?

when power up the system, power LED is lighted, the CPU fan is running, everything seems to be ok, but no screen, no BEEP sound--> hang
need to press RESET button many times, then it will boot to OS without any problem, and system is stable
what's the problem?
thanks for any advice!!!
MB: MSI Neo4 Platinum, BIOS: v1.2
RAM: 512MBx2
CPU: K8 3200+, overclocked to 240x10

Hi all, 1st post here.
System specs:
AMD 3000+ CPU Winchester CBBID
MSI K8N Neo4 SLI Platinum with latest bios
MSI NX6600GT video card
OCZ PowerStream 420 PSU
2 x 256mg OCZ Gold rev 3 dual channel set
Asus DVD-Rom E616P2
Maxtor 80 gig SATA pluged in on SATA #4
Floppy drive
WinXP Pro SP2
I am also affected by this cold boot issue when overclocking. Anything above 229 will give me this issue.
The PSU I am using was running 6 months on an Intel rig without issues and the memory is memtest stable upto 250 at stk.
On top of the cold boot issue I was getting a BSOD sometimes when booting into winxp after the Core Center loads. I noticed I had a jumper on the hdd set to master, so I removed it and the blue screens have stopped ... so far. I was told by a friend that I should plug the HDD into #3 or #4 Sata connector which I did.
Vcore 1.45v + 3.3%
NF4 1.6v
Memory 2.7v on auto according to cpuz128 2.5,3,3,8 1T
HT 3x
CPU ratio 9x
I am able to reach 250 HTT speed (FSB) by using clockgen and it passes windows memtest and is OCCT stable.
However, the only way I have found to pass the 229 barrier in the bios and not have a cold boot, is to set the HT multi to 2x or 1x.
Anything more will produce a cold boot.
Since I removed the jumper from the HDD The system has been running without issues at 226 HTT speed (FSB).
I tried to OC past 229 again and got a cold boot at 230 ... again.
I was using a K8N NF4-F before and had the same cold boot issue however, it would not go over 229 unless the HT multi was set to 1x.
If it doesn't post do the following:
If system is on with a black screen, shut down by holding the start button until it does.
Turn off monitor, speakers and switch off on power supply.
Remove the power cord from power supply.
Push the start button until nothing lights up when you do. This will drain any juice left in capacitors.
After doing this you can reconnect the power supply, turn on the monitor, then the switch on the power supply. I have noticed many times that when you turn on the power supply switch the system will start up without pushing the start button.
If it's still dead, do all of the above again and add this extra step:
After you have pushed the start button to remove any power left in capacitors, push the CMOS clear button on the board and hold it about 1 second.
Then reconnect etc etc.
In the countless times I have done this I have never had to remove the battery but that would be the last thing I would try if all of the above doesn't work for you.
If you cleared the CMOS you will need to enter the system time, date and any other settings you had.
I hoping MSI will address this issue.
The only work around so far I found it using clockgen.

Reboot when cold booting

Hi.
I encrypted my MBP harddrive with the new FileVault feature. Recently my MBP developed an issue where it would hang a while on the spinner when cold booting, then just reboot - and then boot just fine.
This requires me to type in my decryption password two times. Doesn't seem healthy. I tried restoring file permissions from Disk Utility but this didn't help.
Do you know what is causing this and perhaps how I could fix it?
Jorijn

It seems to be a problem with paralles desktop.
http://www.cultofmac.com/113981/parallels-desktop-7-update-fixes-file-fault-full -disk-encryption-problems-get-it-now/
Chris

Satellite P300D-110 integrated webcam is not functioning properly.

Hello everyone,
as the title says, the integrated webcam of my Toshiba Satellite P300D-110 is not functioning properly. Allow me to explain. Using the Camera Assistance Software I can take photo's and record music. If I try to record a video the preview screen turns up black and the end result tuns out black aswell, completely black.
Whenever I try to use my camera with applications such as MSN Live Messenger, Skype or at community websites using Firefox, Internet Explorer or Safari the application in question crashes.
*How did this happen?*
You tell me. This is how it went;
* Day 1: I've started up my laptop and looked at my fresh and clean install of windows vista home premium. I tried out my webcam using the webcam assistance software and it worked like a charm.
* Day 2: Once again I boot up my laptop and try to start my webcam only to find out that it no longer functions.
To give a quick summary of the thread;
* Using Camera Assistance Software provided by Toshiba I can take pictures.
* Using Camera Assistance Software provided by Toshiba I can record sound.
* Using Camera Assistance Software provided by Toshiba I can _*NOT*_ record or preview a video.
* I can not start my camera using any other application such as but not limited to; MSN Live Messenger, Skype, Mozilla Firefox, Internet Explorer and Safar.
* I have downloaded and isntalled the latest drivers from the Toshiba website.
* My laptop is about a week old.
I'm not sure what more I can do, all I want is for the webcam to work, if anyone can help me out please do so.
And if possible WITHOUT having to reinstall Windows Vista Home Premium.
I haven't even used it and wouldn't want to make that a solution for all the problems that might occur in the future.
Sincerely,
a sad customer.

Using Camera Assistance Software provided by Toshiba I can NOT record or preview a video.
Can you please describe the steps how you try to do this? I must ask you this because it runs well on my notebook. When the recording is finished player opens and you can see recorded movie. It is avi format and at the top of this player you can see the path where the movie is saved.
Most strange thing for me is that you cannot use it with Skype. Ok for MSN is not the perfect but there is absolutely no problem with Skype. Check the settings and it must work somehow.

On cold boot or restart, MacPro will not start unless CD Tray is open. Any ideas why ?

On cold boot or restart, MacPro will not startup unless CD Tray is open. Any ideas why ?

hello Singyt, the bug report associated to this kind of crash indicates that it might be a malware related issue.
your crash report also shows a file named "urixalog.dll", which doesn't turn up any search hits on google, which is also slightly suspicious. could you search for that file on your pc and upload it to a site like virustotal.com in order to analyze it.
please do a full scan of your system with the security software already in place and/or a different tool like the [http://www.malwarebytes.org/products/malwarebytes_free free version of malwarebytes].
[[Troubleshoot Firefox issues caused by malware]]
edit: the bug report also suggests that a monitoring program named spector pro/360/... which essentially acts like malware, might cause the issue. in case you have that installed please remove it. otherwise [https://support.mozilla.org/en-US/kb/Firefox%20crashes%20when%20you%20open%20it#w_backdoor-ulrbot-c here] would be a removal guide for urixalog.dll

The keyboard for my iMac 9, 1 got wet and is not working correctlly. Delete,return, and some other keys not functioning. In all caps including numerals. I've left it to dry for a few days but still will not work. Computer now in Safe boot mode and I c

The keyboard for my iMac 9, got wet and is not working correctly. Delete ,return, and some other keys not functioning. In all caps including numerals. I've left it to dry for a few days but still will not work. Computer now in Safe boot mode and I can't login due to all caps and numbers being symbols. Is there anything I can do?

Buy a replacement keyboard. They're only $50-65 USD.
27" i7 iMac (Mid 2011) refurb, OS X Yo (10.10), Mavs, ML & SL, G4 450 MP w/10.5 & 9.2.2

KT4V not seeing HD on cold boot

Guys,
About a 2 months ago I built my first PC, an Athlon XP 2400, 512MB, WD 80GB-8Mb cache HD, DVD-ROM, with a MSI KT4V mobo.
I was finally able to do a new install of XP Pro with the Xmas break and now I have a weird problem...When I do a cold boot it says looking for boot record from floppy, then looking for boot record from CDROM, then finally boot failure.
I've gone into setup and have it set as my HD as the 1st boot device, floppy as 2nd, and DVD as 3rd. When I come out of setup it boots up fine and I can do a warm boot with no problems; until I do a cold boot. Then I get a boot failure again.
I've changed settings so I only have the HD as the boot device and no difference.
I've flashed my BIOS to 1.9 and it took fine but no difference.
Any ideas for me to try?
Thanks.
Lou.

Quote
Originally posted by Wonkanoby
if the wd has no slave it must be jumperless not master
Wow, took out the jumper and all is fine. THANK YOU.
I can't even see boot up specs (amount of RAM, BIOS version, etc) anymore because it boots so fast now, I may have to disable quick-boot now.
I guess I was able to see the boot up specs because it was looking for the master? Can anyone explain this, I'd really like to understand because I've never heard of this before. Is this just a MSI mobo anamoly or in general?
Thanks again everyone, and Wonkanoby, I owe you a beer.
Lou.

HDD detection prob. Not cold boot

This is rather odd... I can boot my pc - and have both my disks detected. If however, i reset - either by button or restart my slave disk does NOT detect.
How does that add up?
I do have the latest bios
Ty in advance.

Thanks for your replies :P
Sorry to not include more info mitch, but i was probably being naive and hoping for some fast, common solution to the problem.
The bios is currently 1.7 - 875p Neo FIS2R.
There are two disks on the primary controller, one strictly master and one strictly slave - They are connected correspondingly to the cable.
It fails to detect the slave, but ONLY on warm boot. This - i find odd. Cold boot works perfectly.
The master disk is a Quantum fireball AS40.0
And the salve is a DeskStar 120GXP 60GB, IBM
I'm sure there's some easy'ish workaround like swapping the slave/master relationship or changing channels and so on, but a fix would be nice.
I hope i have supplied enough info to maybe ring a bell, if not, and i am indeed the only one with this problem - screw it, i like the board better than the disks
- And i did in fact read the mentioned thread, but the it is not the same type of problem. )
Thanks in advance.

Macbook 4.1 webcam not working

Hi, i have problem with webcam. i have installed firmware, loaded uvcvideo, and nothing. no /dev/video0
my kernel version 2.6.37, macbook 4.1

I'm on macbook 4.1 and the iSight has been working since the first time I installed Arch.
Have you done https://wiki.archlinux.org/index.php/Macbook#iSight ?
Just make sure you have the extracted firmware
# ls /lib/firmware/isight.fw
and do a cold boot (not restart but shutdown then power-on).
I don't even have uvcvideo in rc.conf's MODULES() (but I got MOD_AUTOLOAD="yes")
Just a wild guess, have you try installing pommed ?

TS140 Second HD (non-Lenovo) not seen until after boot

I have a TS140 (70A4001MUX), which came with a 500 GB HD. I installed Win7Pro x64, replaced the 4GB RAM with 16 GB of Crucial RAM, and added a second HD (4 TB Western Digital Enterprise WD4000F9YZ). Both HDs are configured GPT, I am booting via UEFI, and the latest firmware (99A) is installed.
This configuration mostly works, except that the second HD isn't visible until after booting. It does not appear in BIOS, which means I cannot boot from it. I have a boot partition on the second HD, cloned from my primary boot partition via Casper software. Normally, this provides me an alternative boot in case of drive failure or corruption on the first HD. But, on the TS140, attempting this alternative boot fails completely, as though the second drive were not there at all. Once I'm booted, though, I can read and write to the second HD all day long. Fwiw, all 16 GB of the new RAM does appear in BIOS.
The second HD:
Does NOT appear in BIOS.
Does appear after boot to Windows 7.
Does appear when booted from CD, such as WinPE and Paragon boot CD.
Why won't BIOS recognize the second drive, that is clearly present and functional? Thanks for any thoughts and suggestions.

Do you see the same behavior on a cold boot and a powered-up reboot?
Since I'm not familiar with ThinkServers, I'm just tossing stuff at the wall here, but I wonder if the new drive is slow to initialize and BIOS is not waiting long enough to detect it. Cold boot and reboot might behave differently in that case. Not sure how to fix that if it is the problem, but it might help to narrow things down.
[edit] There is a hard disk pre-delay option in BIOS. Not quite sure if it's intended for this situation (the one my WAG applies to) but might be worth a try.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

WebCam not functioning on cold boot. Reappear on reboot.

Similar Messages

Maybe you are looking for