WebView problem post upgrade.

I upgraded from ICM 7.2.3 to 7.2.7 and the only two reports that do not work now in WebView are the custom reports. These reports were set up way before I was here and I have hit a wall. When you run these two report the grey areas appear but no data. The stored procedure that runs to copy ther required data to the custom report db is working, I see current data but nothing through the web portal.
Has anyone seen this or have any ideas how to get them working again ?
Thanks !

Do you have a copy of Infomaker? Can you see if you run a manual retrieve data in the report in Infomaker if it pulls out data? If it does you might be a little hard up as it will then be a webview issue which Cisco probably won't look at under a normal SmartNet contract since it's a custom report. Also, you might need to recreate the report in the 10.5 version of Infomaker if the report was created in an old version as I think 7.2(7) requires Infomaker 10.5 as opposed to 10.2 in 7.2(3) from memory.
Cheers,
Nathan

Similar Messages

  • Problem during 11.1.0.7 clusteware upgrade when runnng post upgrade script

    Hello,
    I have encountered a problem whilst upgrading a 3 node RAC cluster to 11.1.0.7 patchset as follows :-
    I ran OUI against the CRS_HOME to upgrade to the 11.1.0.7 patchset. The upgrade completed successfully across all nodes.
    OUI then prompted to run the post install script (_root111.sh)_ as root user on each of the 3 nodes in the cluster, so I did the following (in SERIAL order as recommended):-
    NODE1 - ran crsctl stop crs
    ran root111.sh script
    Both the above actions completed on NODE1 with no problems
    NODE2 ran crsctl stop crs
    ran root111.sh script
    'Text file busy' error received on several files during execution of root111.sh script on NODE2 (This may have been due to the fact that CRS processes had not fully stopped when I invoked the script). The result was that the script did not complete successfully (linking , etc) and CRS did not start up afterwards.
    NODE1 - ran crsctl stop crs
    ran root111.sh script
    Both the above actions completed on NODE3 with no problems
    The result of all the above is that clusterware on NODE2 is in an inconsistent state and CSS and its dependent processes cannot start . What I need to know is how the best way to get out of this situation and complete the upgrade to 11.1.0.7 on all 3 nodes of the cluster. Can I somehow deinstall clusterware on Node2 and reinstall it again independently of Nodes1 and 3 ???
    Any help or advice would be greatly appreciated !
    Thanks,
    Shaun

    Hello ShaunH,
    Take a look on Metalink note 754095.1 This note may helps u.
    Regards,
    Rodrigo Mufalani
    http://mufalani.blogspot.com

  • Given so many posts about problems, is upgrading to maverick worth it?

    Given so many posts about problems, is upgrading to OS X maverick worth it?
    I am content using Snow Leopard OS X 10.6.8.  But my most recent Garmin GPS map updates returned a message that stated, "Mac OSX 10.6 is an older OSX version that is no longer compatible with modern software. We will be ending support for this operating system soon.  To continue using Garmin Express, please upgrade your operating system."
    As others have noted, you don't hear from the users who have installed this upgrade successfully. I've read about problems installing the upgrade and then incompatibilities with other applications once it is installed. Would appreciate your experience and thoughts.  Thanks.

    There are several excellent suggestions here.
    What I did was clone my Snow Leopard drive to a second hard drive, then installed Mavericks on the clone.
    I now have a working Snow Leopard drive as well as a Mavericks drive. I bounce back and forth between them.
    I have symlinks set up so all my documents created on the Mavericks drive go to the Snow Leopard drive, but I have copies of all my applications on both drives. It just seemed easier...
    I had to disable App Nap in both Quickeys and Keyboard Maestro, but they both seem to work well, and neither is the latest version. (Well, Quickeys is the latest version, but it's not a recent version.)
    I only check email in Snow Leopard, never in Mavericks, so my Inbox is not scattered over both systems.
    The Mavericks disk takes longer to boot, and it does occasionally seem sluggish, but it's not a deal-breaker. Like many, I have some legacy software I use, so I don't want to commit to Mavericks full time. But it's nice being able to use both.
    I do like using Safari in full-screen mode, but that's the only program I use full-screen for.
    Hope this helps.
    Andy

  • SBA 8.0 (Hor) to SBA 8.0 (Ver) Industry Application Post Upgrade Problem!

    Hi All,
    I am testing out an upgrade from Siebel 8.0 (Horizontal) to Siebel 8.0 (Vertical) version.
    Post upgrade after GUI Fixes, i did a full compile of siebel_sia.srf!
    But, after i start my Siebel Services & try to access the Sales or High Tech Manufacturing Application, it doesnt come up.
    The log file for both says:
    "siebsrvr\log\SSEObjMgr_enu_0025_26214410.log 8.0 SIA [20405] ENU
    ObjMgrSRFLog     Error     1     00000006486b09f4:0     2008-07-02 13:33:39     (cdf.cpp (668)) SBL-DAT-00142: Could not open repository file 'd:\sia80\siebsrvr\objects\enu\siebel_sia.srf'.
    File does not exist or may be in use by another process.
    ObjMgrCTLog     Error     1     00000006486b09f4:0     2008-07-02 13:33:39     (ctxtmgr.cpp (4492)) SBL-SVC-00208: Please login first."
    Any idea why this is happening? The SRF file exists on the correct location & i dont see any other application accessing the same.
    Regards,
    Shalabhsneha

    Double-check with Siebel Tools that is the same file.
    Check that the new Siebel application is shut down properly and has no "dangling" processes before restart.

  • Pertaining Watches thread in Post Upgrade Problems Forum

    I have posted a question pertaining the watches, I'm not able to see the red indicator nor receiving e-mail.
    Justin, sorry for the very late reply.
    I didn't see your reply and now the threads are read only, so I had no other choice but to post here.
    The threads I watch I am able to see them in the "Watches" in my Control Panel but I do not see the red indicator and I do not receive watches e-mail.
    Thanks in Advance for your help.
    Regards,
    Tony

    The watch e-mails have stopped since the first couple of days of the upgrade, back than I thought they were off, so I waited, but noticed no one was talking about it.
    I checked my mailbox today and I saw a whole bunch of watch mails, some from Sunday 23 November and dated way back till 27 October, but none for this thread. It's weird, there are watch-mails for some threads and not for others.
    Have you guys uploaded anything??
    I haven't change the mail address from the control panel, at least not after the upgrade, but I might have edited that profile page to make sure of my handle, there were cases where the e-mail address was showing instead of the handle at post upgrade.
    However I would want to change the e-mail where I receive the watch mails as soon as they start working.
    oh! one more thing, I still don't see the red indicators for watches on thread list in the forums.
    Thanks for your help guys, really appreciate it.
    Tony

  • ASU-process POST Upgrade Step on SQL database

    Hi All,
    To check this message in the right format kindly click on reply first then click on quote original icon ("").
    I am performing an upgrade from R/3 4.7 to ERP 6.0 SR3, while doing upgrade sapup asking me To perform the manual application specific post upgrade step.
    This phase says to run ASU toolbox by using tx /n/asu/upgrade. when i run this tx is show the below list of steps to be performed with showing severity level of some as optional and many as obligatory.
    Task List                                                                                Severity     SAP R/3 release frm     SAP R/3 release to
    IS-OIL Application Test 600                                                 Optional          
    KP06xx: Termination SYNTAX_ERROR                                                 Obligatory     470                           500
    CGPL: Entries are blank after upgrade                                                Obligatory          
    Error handling of task group execution                                Optional          
    Mobile device cannot confirm TO after release upgrade     Obligatory     470                         600
    Mobile device doesn't find transfer orders after upgrade     Obligatory     470                          600
    Grantee Management - Upgrade from EA-PS 2.00 to ECC 600     Obligatory          
    Convert customizing for warehouse funds ctr scenarios     Optional          
    Various problems classification commitment items (class type     Obligatory          
    Unauthorized error messages udring fiscal year change/reassi     Obligatory          
    RFFMUDX1 migrates incomplete budgeting tables                          Obligatory          
    Non-7bit-ASCII character used for BCS key figures             Obligatory          
    Changes in TKEDR for /ISDFPS/RFFMDISTDERIVALE          Obligatory          
    BCS - Tool for Deleting Obsolete Derivation Strategies     Obligatory          
    BCS Syntax Error on Upgrade from EA-PS 2.00 to ECC 600     Obligatory          
    Migration to ERP 6.0 (EA-PS 6.00)                                         Obligatory          
    Migration EA-PS 2.00 to ERP 5.0 (EA-PS 5.00)                      Obligatory          
    Missing initialization of new fields in table ANLZ                  Obligatory     46C                       470
    Activating VMC for the Internet Pricing and Configurator     Obligatory          
    Customer specific BSEG-fields not transferred                  Optional          
    Conversion of report headers in drilldown-reporting            Optional                                   600
    IBase: Upgrade to Release 4.6C and higher                         Optional     46C                         600
    ZSAPRCKML_COGS: Upgrade to release 4.7 or higher     Optional     46C                      470
    Conversion of CO-Total-Tables                                              Obligatory     46C                      500
    Conversion of CO-line-item table COEP                                Obligatory     46C                       600
    New General Ledger, problems in CO-documents                 Obligatory                               500
    No receivers found in allocations                                          Obligatory     46C                        470
    Conversion Of New Process Parameter Long Texts For Search     Optional     110                       600
    Migration of process parameters in recipe management     Optional     110                        600
    FAQ new depreciation calculation                                        Optional                                600
    Upgrading to SAP R/3 47x200 and SAP ECC 500 with RMGMT     Obligatory     100                       500
    Reloading Table T512W                                                        Optional          
    Converting Short Texts                                                         Obligatory          
    Migrating Data                                                                         Optional     4.7     
    Activating SAP ECC Extensions                                          Optional          
    I am not sure about which steps I have to perform, I am a bit confused.. because some are optional and some are not relevant to my release (as target or source release is different from mine). and also few things are not applied in my envirnoment hence those steps are also not relevant.
    Please suggest me, how to proceed and what to do. please guide if i skip this step now and later  on I apply latest SP than still I need to do all this.
    Regards
    Vinay

    Hi All,
    I also faced a similar issue during upgrade. Some useful findings.
    1. Only super user can access this /n/ASU/START
    2. All the obligatory executable tasks are automatically performed by the system automatically during upgrade.      SAPADM. Only errors (if any) are to be corrected.
    3. Some of the tasks are only to go through some SAP notes as a precaution before upgrade.
    4.  Execute all the checks /n/ASU/UPGRADE
    5. This surely can be skipped, but not advisable.
    regards,
    Amit

  • Upgrade step ASU-process post upgrade step

    Hi All,
    To check this message in the right format kindly click on reply first then click on quote original icon ("").
    I am performing an upgrade from R/3 4.7 to ERP 6.0 SR3, while doing upgrade sapup asking me To perform the manual application specific post upgrade step.
    This phase says to run ASU toolbox by using tx /n/asu/upgrade. when i run this tx is show the below list of steps to be performed with showing severity level of some as optional and many as obligatory.
    Task List                                                                                Severity     SAP R/3 release frm     SAP R/3 release to
    IS-OIL Application Test 600                                                 Optional          
    KP06xx: Termination SYNTAX_ERROR                                                 Obligatory     470                           500
    CGPL: Entries are blank after upgrade                                                Obligatory          
    Error handling of task group execution                                Optional          
    Mobile device cannot confirm TO after release upgrade     Obligatory     470                         600
    Mobile device doesn't find transfer orders after upgrade     Obligatory     470                          600
    Grantee Management - Upgrade from EA-PS 2.00 to ECC 600     Obligatory          
    Convert customizing for warehouse funds ctr scenarios     Optional          
    Various problems classification commitment items (class type     Obligatory          
    Unauthorized error messages udring fiscal year change/reassi     Obligatory          
    RFFMUDX1 migrates incomplete budgeting tables                          Obligatory          
    Non-7bit-ASCII character used for BCS key figures             Obligatory          
    Changes in TKEDR for /ISDFPS/RFFMDISTDERIVALE          Obligatory          
    BCS - Tool for Deleting Obsolete Derivation Strategies     Obligatory          
    BCS Syntax Error on Upgrade from EA-PS 2.00 to ECC 600     Obligatory          
    Migration to ERP 6.0 (EA-PS 6.00)                                         Obligatory          
    Migration EA-PS 2.00 to ERP 5.0 (EA-PS 5.00)                      Obligatory          
    Missing initialization of new fields in table ANLZ                  Obligatory     46C                       470
    Activating VMC for the Internet Pricing and Configurator     Obligatory          
    Customer specific BSEG-fields not transferred                  Optional          
    Conversion of report headers in drilldown-reporting            Optional                                   600
    IBase: Upgrade to Release 4.6C and higher                         Optional     46C                         600
    ZSAPRCKML_COGS: Upgrade to release 4.7 or higher     Optional     46C                      470
    Conversion of CO-Total-Tables                                              Obligatory     46C                      500
    Conversion of CO-line-item table COEP                                Obligatory     46C                       600
    New General Ledger, problems in CO-documents                 Obligatory                               500
    No receivers found in allocations                                          Obligatory     46C                        470
    Conversion Of New Process Parameter Long Texts For Search     Optional     110                       600
    Migration of process parameters in recipe management     Optional     110                        600
    FAQ new depreciation calculation                                        Optional                                600
    Upgrading to SAP R/3 47x200 and SAP ECC 500 with RMGMT     Obligatory     100                       500
    Reloading Table T512W                                                        Optional          
    Converting Short Texts                                                         Obligatory          
    Migrating Data                                                                         Optional     4.7     
    Activating SAP ECC Extensions                                          Optional          
    I am not sure about which steps I have to perform, I am a bit confused.. because some are optional and some are not relevant to my release (as target or source release is different from mine). and also few things are not applied in my envirnoment hence those steps are also not relevant.
    Please suggest me, how to proceed and what to do. please guide if i skip this step now and later  on I apply latest SP than still I need to do all this.
    Regards
    Vinay
    Edited by: Vinay Paul on Sep 11, 2009 10:11 PM

    Hi All,
    I also faced a similar issue during upgrade. Some useful findings.
    1. Only super user can access this /n/ASU/START
    2. All the obligatory executable tasks are automatically performed by the system automatically during upgrade.      SAPADM. Only errors (if any) are to be corrected.
    3. Some of the tasks are only to go through some SAP notes as a precaution before upgrade.
    4.  Execute all the checks /n/ASU/UPGRADE
    5. This surely can be skipped, but not advisable.
    regards,
    Amit

  • Post-upgrade tasks for OWB 10g Release 2

    Hi,
    we're planning to upgrade from OWB 10.1.0.2 to 10.2.x.
    Now, I'm trying to get a clear view on what will be the "post-upgrade" tasks, in terms of manual adaptations, corrections, etc. to get everything back up and running after the upgrade ...
    E.g. : by means of test al already exported a dimension, and imported it in the 10.2 repository ... Turned out that in the pre-10.2 version, there were no validation problems, but as from 10.2 (although the upgrade and import were successful), I got 19 warnings and 2 errors ... because each level needs to have a business or surrogate key ...
    It' s things like that I'm especially interested in, in order to determine the workload after the upgrade ...
    So, feel free to share your experiences ; I'm looking forward to read them!
    Thanks!
    Grtz.

    Here are some from my list. I stopped maintaining it a while ago, we have lots more where this came from. Some of it also apply to older versions of OWB.
    Key lookup     You are to choose input and output attributes BEFORE being able to choose loookup table, all in a time consuming wizard
    Expressions     Copy and paste into expression editor, validation fails for expressions using lowercase (such as "upper" or "substr")
    Renaming attributes     Not possible anymore, you need to open details
    Adding a table component     You must browse in a tree structure (time consuming), not search functionality anymore
    Import     Import converting from 9.2 hangs after 15% in about 10% of all imports
    Import     Some mappings are not possible to import, a total rewrite is necessary
    Deployment     You can only deploy about 5-10 times before you need to restart OWB
    Memory leak     If something goes wrong in OWB, memory is never cleared - JAWAW.exe needs to be removed manually from memory
    Import     Importing mappings one by one (as this is sometimes needed due to OWB), the last directory used is OF COURSE not default when importing the next time
    OWB GUI / mapping editor     When working with components in the mapping editor, an object hidden behind the object you are actually working with is selected prior to the object in visual focus to the user
    BUG!     Urgent: CASE - wrong generated Code
    ANSI JOINS     Remove ANSI-SQL from mapping configuration, otherwise (+) outer joins will not work
    Transformations     Not possible to enter a transformation such as "sysdate", you must find it in a huge tree structure list (no search available)

  • Problems after upgrade: Leopard to Leopard no longer works

    My sister upgraded to Leopard on her iMac(c2d) to Leopard yesterday. Earlier in the day we were able to do video chats with a number of people(her machine Tiger to Fathers machine Leopard). However, since upgrading, we've experienced weird behavior for video chats. Basically in her window she won't see her image(the small one), and I don't see her at all. We've tested this out with a number of other iChat accounts and get the same results. Btw, all machines that are chatting with her are using Leopard. Also, all other forms/capabilities work: screen sharing, sharing of pictures, audio chats.
    Anyone out there have similar problems after upgrading from Tiger to Leopard? I have done the usual adjustments of bandwidth and QT settings, as well as restarts. What else should I try?
    tia,
    n

    I finally resolved this problem: I think the issues/steps would be helpful for anyone who experiences iSight off or not working problems after upgrading to Leopard(then to 10.5.1) on a intel 20" iMac :
    Problem:
    -If you have an internal iSight on an iMac and your camera works fine in Tiger
    -If you upgrade to Leopard
    -If Chat camera doesn't show your image (iSight off) even though the green light is on
    -You can see the other persons video on iChat
    -Your friends can here you and you can share screens, files, etc.....everything but have them see you
    These are the initial steps I took:
    - Deleted the pLists(or stored preferences for the Application) described at the top of this thread
    - Was told it might be slow internet connection so did various things: disconnected other computers, changed wireless to "G" only
    - Specifically Opened of ports spec'd for Leopard on router (even though I hadn't needed to do this under Tiger)
    - Tried chats with various people on various fast/slow networks
    - Restarted all aspects of the network: router, wireless access point, computer
    - Checked to see if the iSight was shown in 'System Profiler'. It was found in 'About This Mac->More Info->System Profiler->USB'
    - Clicked Video icon in iChat Buddies window(to the right of your name) and coudn't see my image
    - Opened 'PhotoBooth' and coudn't see my image(black screen)
    - Opened iMovie and couldn't capture video via the iSight(black screen)
    - Opened iChat->Preferences->Video and couldn't see my image
    - Validated that 'Camera is Enabled' in iChat->Video->Camera is Enabled
    If you are experiencing a similar problem with you built-in iSight, I would probably focus on the last 5 things that I did. What they showed me was that the iSight was just not capturing video even though it was capturing sound in 3 different applications.
    The solution to iSight Off or iSight Not Responding or No Video is......reset your computer! I had thought my sister performed this but it turns out she hadn't. Here's the link to this procedure:
    http://docs.info.apple.com/article.html?artnum=303446
    Very easy to do though: Power off computer and unplug all cables, including power cable for at least 15 seconds. Plug everything back in and power up the computer and retry clicking on the 'Video' icon next to your login name. If you see yourself then...problem is solved.
    While I eventually found posts in several other forums, it took me the better part of a week. To try this simple step. I wish I had done so straight away. Oy. I guess I learned a lot about ports, speed etc.
    I hope this helps.

  • Problems after upgrading to iTunes version 6

    Hello,
    I've been going through the threads a lot since I have had problems after upgrading to iTunes v. 6. It looks like a lot of people have had the same issues, and I have tried some things that were recommended. After I upgraded, iTunes would not open. I tried:
    1. deleting sidb file
    2. doing the msconfig thing suggested in discussion boards
    3. going into safe mode and deleting 4 and 6 letter weird files in DOS - I found 3 that I deleted
    iTunes worked after this -- then I bought a song and it said my computer was not authorized, after I authorized computer (that never happened before), iTunes worked for about 15 more minutes and then closed down abruptly. I haven't been able to open it since.
    I also downloaded Spybot search & destroy and that did not find anything. I am using McAfee, and have scanned for viruses with McAfee and AdAware.
    Now, when I restart my computer, a bunch of windows pop up with Chinese/Japanese looking characters and say that device (I think) was not found. I seem to be able to use everything except iTunes and Quicktime. When I open the Task Manager, iPodService.exe and iTunesHelper.exe and qttask.exe are there, but when I click on Quicktime or iTunes the file flashes in Task Manager and then disappears.
    I'm not sure where to go from here.
    Any help would be apppreciated -- I'd like to be able to open iTunes!

    Hello,
    I used Nickroo's post:
    I was able to get iTunes launched (with the help of Tech Support) in a very unsafe environment. I owe it to those who may need this after me. It will get you going, but you will be extremely vulnerable to internet virus assaults. Please do not use this approach, until you have exhausted every other available solution for your issue in the KB.
    There are three Steps 1) Uninstall 2) Disble and 3) Reinstall.
    UNISTALL Uninstall iTunes using Windows utility Add Remove Program available in Control Panel.
    DISABLE Disable all third party System Services and Startup Items using using MSCONFIG utility as described in Service Document http://docs.info.apple.com/article.html?artnum=302538
    RE-INSTALL Re-install iTunes6 + QT7. Launch it under the Selective Startup Option.
    It worked ! You realize among other things at this point you have your Antivirus and Firewall disabled. When I started my computer in the Normal Startup Option, iTunes fails to work again. So I have ahead of me the long and ardous task of ruling out the service that is causing conflict with iTunes6. Then work with the software vendor to arrive at a solution.
    This seems to have worked so far- I haven't started to go through ruling out what made iTunes not work; I also haven't tried to connect my iPod or burn a CD, so we'll see.
    Windows XP

  • Audio Tracks on my iPhone stopped working post upgraded to iOS 5.

    Audio Tracks on my iPhone stopped working post upgraded to iOS 5.
    Quiet a lot of my tracks do not play on my iPhone 4 after I upgraded to iOS 5. The the seeker bar does not progress and it looks stuck.
    Could someone please help.
    Regards,
    S!d

    Hi !
    I am currently having the same problem, since I upgraded my iPhone 4 to iOS 5, many tracks don't work. They were working before. Some are working but half isn't.
    Tried to restore, remake playlist, delete every tracks et put them back. Same prob.
    Please help !
    Regards,
    Rom

  • Error on Oracle 11gR2 RAC database Post upgrade step

    [Upgrade the Oracle Clusterware Configuration|http://docs.oracle.com/cd/E11882_01/server.112/e23633/afterup.htm] Problem Description:
    O.S Version: HP-UX B.11.31 U ia64
    It is upgrading of Oracle RAC 2 node database from 11.1.0.7.0 to 11.2.0.3.0
    I receive following error while perfoming the post upgrade step
    indba1 racdb> srvctl upgrade database -d racdb -o /app/oracle/product/11.2.0.3/db
    PRCD-1231 : Failed to upgrade configuration of database racdb to version 11.2.0.3.0 in new Oracle home /app/oracle/product/11.2.0.3/db
    PRKC-1136 : Unable to find version for database with name racdb
    Actually I am performing the step "Upgrade the Oracle Clusterware Configuration" whill getting the error.
    When I tried on below;
    indba1 racdbp> srvctl upgrade database -d racdb -o /app/oracle/product/11.2.0.3/db
    PRCD-1231 : Failed to upgrade configuration of database racdb to version 11.2.0.3.0 in new Oracle home /app/oracle/product/11.2.0.3/db
    PRKC-1136 : Unable to find version for database with name racdb

    Output from Oracle 11.1.0.7 Home:
    oracle@indba1:/app/oracle/product/11g/db_1 $ srvctl config database -d racdb
    PRKR-1001 : cluster database racdb does not exist
    PRKO-2005 : Application error: Failure in getting Cluster Database Configuration for: racdb
    Output from Oracle 11.2.0.3 Home:
    oracle@usfsdba1:/app/oracle/product/11.2.0.3/db $ srvctl config database -d racdb
    PRKR-1001 : cluster database racdb does not exist
    PRKO-2005 : Application error: Failure in getting Cluster Database Configuration for: racdb

  • I am having a problem while upgrading my iTunes to  10.5.

    I am having a problem while upgrading my iTunes to 10.5. I've been trying to use the 64-bit installer and have tried disabling my anti-virus software. In the end of the installing process, this error comes up:
    Could not open  thekey:  HKEY_CLASSES_ROOT\Installer\Products\F65865963B6B0EB4ABB0F894B53E0233\SourceLis t\Media
    I`ve already tried to change the permissions options in ``regedit``, but when I try to change them , it still complains about not having access to the key, it says ``You do not have permission to view the current permission settings for Media, but you can make permission changes``I click in ``Ok`` and when I tried to change the options, another error comes up:
    ``Unable to save permission changes on Media. Access is denied.`` 
    Can anybody help?

    Try drifting up to the SourceList key, mariana. If you are able to change permissions there, try to make the changes described in Marconato's post (except that you're doing it in SourceList rather than Media):
    Re: Could not open key: UNKNOWN\Installer\Products\9B00314CD581E574FBCE93FE37F2911B\SourceList\Media.      Verify that you have sufficient access to that key, or contact your support personnel.
    (If we can't get to the permissions on the key directly, it seems that sometimes going up one level and using the "inherit from parent" setting can get the permissions in.)

  • Syntax Error in Web UI component post upgrade

    Hi Experts,
    We have a enhanced component in IC agent which is giving syntax error post upgrade from 7.0 to EHP2. It seems some attributes have been removed/altered in the new super class.
    In this case do we need to delete the component enhancement and re do the effort or is there any way to regenerate the enhanced component ?
    Thanks, Please help.
    Rohit

    Hi Rohit,
    I've written a few blogs where I collected the different steps necessary in CRM after an EhP or SP upgrade. Furthermore I described solutions to common problems in these blogs. Please have a look an see if one of the described approaches is suitable for your problem.
    http://scn.sap.com/docs/DOC-44983
    http://scn.sap.com/docs/DOC-49317
    http://scn.sap.com/community/crm/upgrades-and-enhancement-packs/blog/2014/02/21/sap-crm-ehp3-upgrade
    Best,
    Christian

  • Post Upgrade transport

    We're currently in our upgrade project. I have a concern about our transport system after upgrading to ECC 5.0. Here is my scenario. We are currently upgrading from 4.6C to ECC 5.0.  All systems are central installations no app servers. Production server consist of PRD. Second server contains DEV and QA. The transport directory is shared between these server.
    Upgrade landscape is on another server containing a Dev 5.0 and QA 5.0 system. Our go live plan is to upgrade PRD after testing on QA 5.0. I will manually add post upgrade transports to PRD and then import. My question is, will I run into any problems by manually adding the transports to PRD?
    Yes, I know 6.0 is the better upgrade version but it's a long story.
    Thank you in advance.

    Hi Martin,
    What do you mean by post upgrade transport if it is SPDD & SPAU fixes then for this you will get option during the upgrade to add a single transport request.
    If you are talking @ the development happening into DEV & QA system during the production system upgrade the you just need to keep track of the transport sequance and need to import in a same sequance in the PRD after the upgrade
    Hope this will help you, do revert if you need any more info.
    Best Regards,
    Sachin.

Maybe you are looking for