Weird Problem! Cisco 2950

Hi, I really dont know if this issue is applicable here but I am desperate for help now. We have a wireless project providing internet access in a very remote location. There are wireless mesh accesspoints connected back to back by wireless Point2MultiPoint Links (P2MP). I have 2 BSU (Base Station Units) each connected to 3 CPEs. The 2 BSU's are connected to zero configuratoin 2950 switch.Below is a brief on the technical scenario:-
1. Wired backhaul subnet 10.10.10.0/27.
BSU ONE: 10.10.10.2
BSU TWO: 10.10.10.3
2. DHCP Relay 192.168.2.0/24.
Issue:
The problem is that when I connect both the BSU to the switch they perform well. But after 10-15 minutes the other BSU (10.10.10.2) starts giving huge delays and finally times out. Disconnecting the stable BSU (10.10.10.3) from the switch brings the other one up. The switch already has STP enabled.
Is there a loop in the network? Any problem with the BSUs? Are the Mesh Access Points broadcasting? How do I troubleshoot this? Your valuable comments, suggestions will definitely get me somehwere.
Attachments: network scenario, ping snapshots of the BSUs.
Regards
Sarfaraz

Hi Dennis,
We are using Tropos 5210 Mesh Routers as Access Points and a Colubris 3500 Controller for a portal page.
The distance between each mesh unit is more than 50 metres.

Similar Messages

  • Vmps problem (cisco 2950)

    I see, that the cisco is frequently sending vmps (vqp) requests. Instead of one per 60 minutes, I see a lot more.
    Can someone explain why ?
    Cisco Internetwork Operating System Software
    IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA10, RELEASE SOFTWARE (fc2)
    Copyright (c) 1986-2007 by cisco Systems, Inc.
    Compiled Tue 08-May-07 11:50 by myl
    Image text-base: 0x80010000, data-base: 0x8056C000
    VQP Client Status:
    VMPS VQP Version: 1
    Reconfirm Interval: 60 min
    Server Retry Count: 3
    VMPS domain server: 172.16.13.146 (primary, current)
    Reconfirmation status
    VMPS Action: Success
    VMPS Client Statistics
    VQP Queries: 18
    VQP Responses: 18
    VMPS Changes: 0
    VQP Shutdowns: 0
    VQP Denied: 0
    VQP Wrong Domain: 0
    VQP Wrong Version: 0
    VQP Insufficient Resource: 0
    part of 'show log':
    00:36:44: VQPC PAK: rcvd packet from VMPS
    00:36:44: VQPC PAK: transaction ID = 0x00000006
    00:36:44: VQPC: rcvd response, transID = 0x00000006
    00:36:44: VQPC PAK: VLAN name TLV, vlanName = default
    00:36:44: VQPC PAK: Cookie TLV, cookie = 000b.cde3.855f, length = 6
    00:39:41: VQPC PAK: xmt transaction ID = 0x00000007
    00:39:41: VQPC PAK: sending query to VMPS
    00:39:41: VQPC PAK:
    00:39:41: VQPC PAK: rcvd packet from VMPS
    00:39:41: VQPC PAK: transaction ID = 0x00000007
    00:39:41: VQPC: rcvd response, transID = 0x00000007
    00:39:41: VQPC PAK: VLAN name TLV, vlanName = default
    00:39:41: VQPC PAK: Cookie TLV, cookie = 000b.cde3.855f, length = 6
    00:40:38: VQPC PAK: xmt transaction ID = 0x00000008
    00:40:38: VQPC PAK: sending query to VMPS
    00:40:38: VQPC PAK:
    00:40:38: VQPC PAK: rcvd packet from VMPS
    00:40:38: VQPC PAK: transaction ID = 0x00000008
    00:40:38: VQPC: rcvd response, transID = 0x00000008
    00:40:38: VQPC PAK: VLAN name TLV, vlanName = default
    00:40:38: VQPC PAK: Cookie TLV, cookie = 000b.cde3.855f, length = 6
    00:53:55: VQPC PAK: xmt transaction ID = 0x00000009
    00:53:55: VQPC PAK: sending query to VMPS
    etc............
    I ONLY HAVE THIS PROBLEM WHEN THE SWITCH IS CONNECTED TO ANOTHER SWITCH ! IF IT RUNS 'stand alone', ALL SEEMS TO WORK AS IT SHOULD BE. WHY ?
    HELP !!

    Hi Dennis,
    We are using Tropos 5210 Mesh Routers as Access Points and a Colubris 3500 Controller for a portal page.
    The distance between each mesh unit is more than 50 metres.

  • Cisco 2950 trunk s shutdown problem

    i have a network on fiber.i have use cisco 2950 switches in that topolgy.my problem is that sometimes the trunk ports automatically shutdown which creates a lot of problem.when the ports shutdown the cpu usage of switch goes to 66.normally it remains at 30.secondly i give redunant path to every vlan and now the vlan spanning tree has stopped because cisco 2950 doesnot support more than 64 stp.
    What could be the problem?or iam thinking about the bandwidth..How much bandwidth does cisco 2950 switch can max carry?
    Posted by WebUser Umair Zia from Cisco Support Community App

    If the trunk port went into shutdown, then there's gotta be a reason why.
    Can you post the output to the command "sh post" particularly the time when the port went "down"?

  • Configuring wired 802.1x with Cisco 2950 and NPS 2012 problem

    Hi,
    I am trying to setup wired authentication on my corporate network. For testing purposes, I have setup a Cisco 2950 switch for RADIUS authentication.
    On the first day of the test, access messages were appearing on the event log of the 2012 Server and  we were trying to address the issues with EAP and policy.(Network Policy and Access services)
    Then, suddenly no events are written to the event log for the wired authentication. Accounting data is written to the log file at c:\windows\system32\logfiles, but nothing happens on the event log as if the NPS is not answering. We are using the same server for wireless 802.1x and all is working fine.
    Checking the wired autoconfig log on the client, Restart Reason : Onex Auth Timeout appears.
    Logging seems to be configured properly, there are no entries in event log. Below is the debug information from the 2950 switch;
    KAT2-BATISW1#
    00:18:28: dot1x-registry:dot1x_port_linkchange invoked on interface FastEthernet
    0/17
    00:18:28: dot1x-registry:dot1x_port_linkcomingup invoked on interface FastEthern
    et0/17
    00:18:28: dot1x-ev:dot1x_port_enable: set dot1x ask handler on interface FastEth
    ernet0/17
    00:18:28: dot1x-ev:dot1x_update_port_direction: Updating oper direction for Fa0/
    17 (admin=Both, current oper=Both)
    00:18:28: dot1x-ev:dot1x_update_port_direction: New oper direction for Fa0/17 is
     Both
    00:18:28:     dot1x_auth Fa0/17: initial state auth_initialize has enter
    00:18:28: dot1x-sm:Fa0/17:0000.0000.0000:auth_initialize_enter called
    00:18:28: dot1x-ev:auth_initialize_enter:0000.0000.0000: Current ID=0
    00:18:28:     dot1x_auth Fa0/17: during state auth_initialize, got event 0(cfg_a
    uto)
    00:18:28: @@@ dot1x_auth Fa0/17: auth_initialize -> auth_disconnected
    00:18:28: dot1x-sm:Fa0/17:0000.0000.0000:auth_disconnected_enter_action called
    00:18:28: dot1x-sm:
    dot1x_update_port_status called with port_status = DOT1X_PORT_STATUS_UNAUTHORIZE
    D
    00:18:28: dot1x-ev:dot1x_update_port_direction: Updating oper direction for Fa0/
    17 (admin=Both, current oper=Both)
    00:18:28: dot1x-ev:dot1x_update_port_direction: New oper direction for Fa0/17 is
     Both
    00:18:28: dot1x-ev:dot1x_port_cleanup_author: cleanup author on interface FastEt
    hernet0/17
    00:18:28: dot1x-ev:dot1x_update_port_status: Called with host_mode=0 state UNAUT
    HORIZED
    00:18:28: dot1x-ev:dot1x_update_port_status: using mac 0000.0000.0000 to send po
    rt to unauthorized on vlan 0
    00:18:28: dot1x-ev:Found a supplicant block for mac 0000.0000.0000 80D71C74
    00:18:28: dot1x-ev:dot1x_port_unauthorized: Host-mode=0 radius/guest vlan=0 on F
    astEthernet0/17
    00:18:28: dot1x-ev:    GuestVlan configured=0
    00:18:28: dot1x-ev:supplicant 0000.0000.0000 is default
    00:18:28: dot1x-ev:supplicant 0000.0000.0000 is last
    00:18:28: dot1x-ev:Found a supplicant block for mac 0000.0000.0000 80D71C74
    00:18:28: dot1x-ev:0000.0000.0000 is now unauthorized on port FastEthernet0/17
    00:18:28: dot1x-ev:dot1x_port_cleanup_author: cleanup author on interface FastEt
    hernet0/17
    00:18:28: dot1x-ev:Enter function dot1x_aaa_acct_end
    00:18:28: dot1x-ev:Found a supplicant block for mac 0000.0000.0000 80D71C74
    00:18:28: dot1x-ev:Found a supplicant block for mac 0000.0000.0000 80D71C74
    00:18:28:     dot1x_auth Fa0/17: idle during state auth_disconnected
    00:18:28: @@@ dot1x_auth Fa0/17: auth_disconnected -> auth_connecting
    00:18:28: dot1x-sm:Fa0/17:0000.0000.0000:auth_connecting_enter called
    00:18:28:     dot1x_bend Fa0/17: initial state dot1x_bend_initialize has enter
    00:18:28: dot1x-sm:Dot1x Initialize State Entered
    00:18:28:     dot1x_bend Fa0/17: initial state dot1x_bend_initialize has idle
    00:18:28:     dot1x_bend Fa0/17: during state dot1x_bend_initialize, got event 1
    6383(idle)
    00:18:28: @@@ dot1x_bend Fa0/17: dot1x_bend_initialize -> dot1x_bend_idle
    00:18:28: dot1x-sm:Dot1x Idle State Entered
    00:18:28: dot1x-ev:Created port supplicant block 0000.0000.0000 expected_id=0 cu
    rrent_id=0
    00:18:28: dot1x-ev:dot1x_init_sb_oper_info:Default port supplicant at memloc 80D
    71C74
    00:18:28: dot1x-ev:dot1x_post_message_to_auth_sm: cleanup author from interface
    FastEthernet0/17
    00:18:28: dot1x-ev:
    dot1x_post_message_to_auth_sm:0000.0000.0000: Sending TX_FAIL
    00:18:28: dot1x-ev:dot1x_post_message_to_auth_sm:0000.0000.0000: Current ID=1
    00:18:28: dot1x-ev:Transmitting an EAPOL frame on FastEthernet0/17
    00:18:28: dot1x-packet:Tx EAP-Failure, id 0, ver 1, len 4 (Fa0/17)
    00:18:28: dot1x-registry:registry:dot1x_ether_macaddr called
    00:18:28: dot1x-packet:Tx sa=000f.24e9.72d1, da=0180.c200.0003, et 888E (Fa0/17)
    00:18:28: dot1x-ev:dot1x_post_message_to_auth_sm: cleanup author from interface
    FastEthernet0/17
    00:18:28: dot1x-ev:dot1x_post_message_to_auth_sm: Tx for req_id for supplicant 0
    000.0000.0000
    00:18:28: dot1x-ev:Transmitting an EAPOL frame on FastEthernet0/17
    00:18:28: dot1x-packet:Tx EAP-Request(Id), id 1, ver 1, len 5 (Fa0/17)
    00:18:28: dot1x-registry:registry:dot1x_ether_macaddr called
    00:18:28: dot1x-packet:Tx sa=000f.24e9.72d1, da=0180.c200.0003, et 888E (Fa0/17)
    00:18:28: dot1x-ev:Received an EAPOL frame on interface FastEthernet0/17
    00:18:28: dot1x-packet:Rx EAP-Response(Id), id 1, ver 1, len 21 (Fa0/17)
    00:18:28: dot1x-packet:Rx sa=0024.1d10.d7c5, da=0180.c200.0003, et 888E (Fa0/17)
    00:18:28: dot1x-ev:Couldn't find a supplicant block for mac 0024.1d10.d7c5
    00:18:28: dot1x-ev:Couldn't find a supplicant block for mac 0024.1d10.d7c5
    00:18:28: dot1x-ev:Found a supplicant block for mac 0000.0000.0000 80D71C74
    00:18:28:     dot1x_auth Fa0/17: initial state auth_initialize has enter
    00:18:28: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_initialize_enter called
    00:18:28: dot1x-ev:auth_initialize_enter:0024.1d10.d7c5: Current ID=0
    00:18:28:     dot1x_auth Fa0/17: during state auth_initialize, got event 0(cfg_a
    uto)
    00:18:28: @@@ dot1x_auth Fa0/17: auth_initialize -> auth_disconnected
    00:18:28: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_disconnected_enter_action called
    00:18:28: dot1x-sm:
    dot1x_update_port_status called with port_status = DOT1X_PORT_STATUS_UNAUTHORIZE
    D
    00:18:28: dot1x-ev:dot1x_update_port_direction: Updating oper direction for Fa0/
    17 (admin=Both, current oper=Both)
    00:18:28: dot1x-ev:dot1x_update_port_direction: New oper direction for Fa0/17 is
     Both
    00:18:28: dot1x-ev:dot1x_port_cleanup_author: cleanup author on interface FastEt
    hernet0/17
    00:18:28: dot1x-ev:dot1x_update_port_status: Called with host_mode=0 state UNAUT
    HORIZED
    00:18:28: dot1x-ev:dot1x_update_port_status: using mac 0024.1d10.d7c5 to send po
    rt to unauthorized on vlan 0
    00:18:28: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:28: dot1x-ev:dot1x_port_unauthorized: Host-mode=0 radius/guest vlan=0 on F
    astEthernet0/17
    00:18:28: dot1x-ev:    GuestVlan configured=0
    00:18:28: dot1x-ev:supplicant 0024.1d10.d7c5 is last
    00:18:28: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:28: dot1x-ev:0024.1d10.d7c5 is now unauthorized on port FastEthernet0/17
    00:18:28: dot1x-ev:dot1x_port_cleanup_author: cleanup author on interface FastEt
    hernet0/17
    00:18:28: dot1x-ev:Enter function dot1x_aaa_acct_end
    00:18:28: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:28: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:28:     dot1x_auth Fa0/17: idle during state auth_disconnected
    00:18:28: @@@ dot1x_auth Fa0/17: auth_disconnected -> auth_connecting
    00:18:28: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_connecting_enter called
    00:18:28:     dot1x_bend Fa0/17: initial state dot1x_bend_initialize has enter
    00:18:28: dot1x-sm:Dot1x Initialize State Entered
    00:18:28:     dot1x_bend Fa0/17: initial state dot1x_bend_initialize has idle
    00:18:28:     dot1x_bend Fa0/17: during state dot1x_bend_initialize, got event 1
    6383(idle)
    00:18:28: @@@ dot1x_bend Fa0/17: dot1x_bend_initialize -> dot1x_bend_idle
    00:18:28: dot1x-sm:Dot1x Idle State Entered
    00:18:28: dot1x-ev:Created port supplicant block 0024.1d10.d7c5 expected_id=1 cu
    rrent_id=1
    00:18:28: dot1x-ev:dot1x_post_message_to_auth_sm: cleanup author from interface
    FastEthernet0/17
    00:18:28: dot1x-ev:dot1x_post_message_to_auth_sm: cleanup author from interface
    FastEthernet0/17
    00:18:28: dot1x-ev:dot1x_post_message_to_auth_sm: Tx for req_id for supplicant 0
    024.1d10.d7c5
    00:18:28: dot1x-ev:Transmitting an EAPOL frame on FastEthernet0/17
    00:18:28: dot1x-packet:Tx EAP-Request(Id), id 0, ver 1, len 5 (Fa0/17)
    00:18:28: dot1x-registry:registry:dot1x_ether_macaddr called
    00:18:28: dot1x-packet:Tx sa=000f.24e9.72d1, da=0180.c200.0003, et 888E (Fa0/17)
    00:18:28: dot1x-ev:Received an EAPOL frame on interface FastEthernet0/17
    00:18:28: dot1x-packet:Rx EAP-Response(Id), id 0, ver 1, len 21 (Fa0/17)
    00:18:28: dot1x-packet:Rx sa=0024.1d10.d7c5, da=0180.c200.0003, et 888E (Fa0/17)
    00:18:28: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:28: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:28:     dot1x_auth Fa0/17: during state auth_connecting, got event 7(rxRes
    pId)
    00:18:28: @@@ dot1x_auth Fa0/17: auth_connecting -> auth_authenticating
    00:18:28: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_connecting_exit alled
    00:18:28: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_authenticating_enter called
    00:18:28: dot1x-ev:sending AUTH_START to BEND for supp_info=80D7E584
    00:18:28: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_connecting_authenticating_action c
    alled
    00:18:28: dot1x-ev:Received AuthStart from Authenticator for supp_info=80D7E584
    00:18:28:     dot1x_bend Fa0/17: during state dot1x_bend_idle, got event 1(auth_
    start)
    00:18:28: @@@ dot1x_bend Fa0/17: dot1x_bend_idle -> dot1x_bend_response
    00:18:28: dot1x-sm:Dot1x Response State Entered for supp_info=80D7E584 hwidb=807
    D353C, swidb=807D4898 on intf=Fa0/17
    00:18:28: dot1x-ev:Managed Timer in sub-block attached as leaf to master
    00:18:28: dot1x-sm:Started the ServerTimeout Timer
    00:18:28: dot1x-ev:Going to Send Request to AAA Client on RP for id = 0 and leng
    th = 21
    00:18:28: dot1x-ev:Got a Request from SP to send it to Radius with id 4294967283
    00:18:28: dot1x-ev:Couldn't Find a process thats already handling the request fo
    r this id 0
    00:18:28: dot1x-ev:Inserted AAA request for interface FastEthernet0/17, MAC 0024
    .1d10.d7c5, VLAN 0 on pending request queue
    00:18:28: dot1x-ev:Found a free slot at slot 0
    00:18:28: dot1x-ev:Found a free slot at slot 0
    00:18:28: dot1x-ev:Processing AAA request for interface FastEthernet0/17, MAC 00
    24.1d10.d7c5, VLAN 0 from pending request queue
    00:18:28: dot1x-ev:Request id = -13 and length = 21
    00:18:28: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:28: dot1x-ev:The Interface on which we got this AAA Request is FastEtherne
    t0/17
    00:18:28: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:28: dot1x-ev:Username is DUZEY\SAYTAMANER
    00:18:28: dot1x-ev:MAC Address is 0024.1d10.d7c5
    00:18:28: dot1x-ev:RemAddr is 00-24-1D-10-D7-C5/00-0F-24-E9-72-D1
    00:18:28: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:30: %LINK-3-UPDOWN: Interface FastEthernet0/17, changed state to up
    00:18:46: dot1x-ev:Received an EAPOL frame on interface FastEthernet0/17
    00:18:46: dot1x-packet:Rx EAPOL-Start, ver 1, len 0 (Fa0/17)
    00:18:46: dot1x-packet:Rx sa=0024.1d10.d7c5, da=0180.c200.0003, et 888E (Fa0/17)
    00:18:46: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:46: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:46: dot1x-ev:RECEIVED mac =0024.1d10.d7c5 and Stored MAC =0024.1d10.d7c5
    00:18:46:     dot1x_auth Fa0/17: during state auth_authenticating, got event 4(e
    apStart)
    00:18:46: @@@ dot1x_auth Fa0/17: auth_authenticating -> auth_aborting
    00:18:46: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_aborting_enter called
    00:18:46: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_authenticating_aborting_action cal
    led
    00:18:46: dot1x-ev:Received DOT1X_MSG_AUTH_ABORT: setting msg_id = 0
    00:18:46:     dot1x_bend Fa0/17: during state dot1x_bend_response, got event 5(i
    nitialize)
    00:18:46: @@@ dot1x_bend Fa0/17: dot1x_bend_response -> dot1x_bend_initialize
    00:18:46: dot1x-sm:Dot1x Initialize State Entered
    00:18:46:     dot1x_bend Fa0/17: idle during state dot1x_bend_initialize
    00:18:46: @@@ dot1x_bend Fa0/17: dot1x_bend_initialize -> dot1x_bend_idle
    00:18:46: dot1x-sm:Dot1x Idle State Entered
    00:18:46:     dot1x_auth Fa0/17: during state auth_aborting, got event 16(noauth
    Abort_noeapLogoff)
    00:18:46: @@@ dot1x_auth Fa0/17: auth_aborting -> auth_connecting
    00:18:46: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_connecting_enter called
    00:18:46: dot1x-ev:dot1x_post_message_to_auth_sm: Tx for req_id for supplicant 0
    024.1d10.d7c5
    00:18:46: dot1x-ev:Transmitting an EAPOL frame on FastEthernet0/17
    00:18:46: dot1x-packet:Tx EAP-Request(Id), id 1, ver 1, len 5 (Fa0/17)
    00:18:46: dot1x-registry:registry:dot1x_ether_macaddr called
    00:18:46: dot1x-packet:Tx sa=000f.24e9.72d1, da=0180.c200.0003, et 888E (Fa0/17)
    00:18:46: dot1x-ev:Received an EAPOL frame on interface FastEthernet0/17
    00:18:46: dot1x-packet:Rx EAP-Response(Id), id 1, ver 1, len 21 (Fa0/17)
    00:18:46: dot1x-packet:Rx sa=0024.1d10.d7c5, da=0180.c200.0003, et 888E (Fa0/17)
    00:18:46: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:46: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:46: dot1x-ev:RECEIVED mac =0024.1d10.d7c5 and Stored MAC =0024.1d10.d7c5
    00:18:46:     dot1x_auth Fa0/17: during state auth_connecting, got event 7(rxRes
    pId)
    00:18:46: @@@ dot1x_auth Fa0/17: auth_connecting -> auth_authenticating
    00:18:46: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_connecting_exit alled
    00:18:46: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_authenticating_enter called
    00:18:46: dot1x-ev:sending AUTH_START to BEND for supp_info=80D7E584
    00:18:46: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_connecting_authenticating_action c
    alled
    00:18:46: dot1x-ev:Received AuthStart from Authenticator for supp_info=80D7E584
    00:18:46:     dot1x_bend Fa0/17: during state dot1x_bend_idle, got event 1(auth_
    start)
    00:18:46: @@@ dot1x_bend Fa0/17: dot1x_bend_idle -> dot1x_bend_response
    00:18:46: dot1x-sm:Dot1x Response State Entered for supp_info=80D7E584 hwidb=807
    D353C, swidb=807D4898 on intf=Fa0/17
    00:18:46: dot1x-ev:Managed Timer in sub-block attached as leaf to master
    00:18:46: dot1x-sm:Started the ServerTimeout Timer
    00:18:46: dot1x-ev:Going to Send Request to AAA Client on RP for id = 1 and leng
    th = 21
    00:18:46: dot1x-ev:Got a Request from SP to send it to Radius with id 4294967284
    00:18:46: dot1x-ev:Found a process thats already handling therequest for this id
     1
    00:18:48: dot1x-err:Dot1x Authentication failed (AAA_AUTHEN_STATUS_ERROR)
    00:18:48: dot1x-ev:Received VLAN is No Vlan
    00:18:48: dot1x-ev:Enqueued the response to BackEnd
    00:18:48: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:48: dot1x-ev:Enter function dot1x_aaa_acct_end
    00:18:48: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:48: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:48: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:18:48: dot1x-ev:Received QUEUE EVENT in response to AAA Request
    00:18:58: dot1x-sm:Fa0/17:0000.0000.0000:dot1x_process_txWhen_expire called
    00:18:58:     dot1x_auth Fa0/17: during state auth_connecting, got event 19(txWh
    en_expire)
    00:18:58: @@@ dot1x_auth Fa0/17: auth_connecting -> auth_connecting
    00:18:58: dot1x-sm:Fa0/17:0000.0000.0000:auth_connecting_connecting_action calle
    d
    00:18:58: dot1x-ev:dot1x_post_message_to_auth_sm: Skipping tx for req_id for def
    ault supplicant
    00:19:07: dot1x-ev:Received an EAPOL frame on interface FastEthernet0/17
    00:19:07: dot1x-packet:Rx EAPOL-Start, ver 1, len 0 (Fa0/17)
    00:19:07: dot1x-packet:Rx sa=0024.1d10.d7c5, da=0180.c200.0003, et 888E (Fa0/17)
    00:19:07: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:19:07: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:19:07: dot1x-ev:RECEIVED mac =0024.1d10.d7c5 and Stored MAC =0024.1d10.d7c5
    00:19:07:     dot1x_auth Fa0/17: during state auth_authenticating, got event 4(e
    apStart)
    00:19:07: @@@ dot1x_auth Fa0/17: auth_authenticating -> auth_aborting
    00:19:07: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_aborting_enter called
    00:19:07: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_authenticating_aborting_action cal
    led
    00:19:07: dot1x-ev:Received DOT1X_MSG_AUTH_ABORT: setting msg_id = 0
    00:19:07:     dot1x_bend Fa0/17: during state dot1x_bend_response, got event 5(i
    nitialize)
    00:19:07: @@@ dot1x_bend Fa0/17: dot1x_bend_response -> dot1x_bend_initialize
    00:19:07: dot1x-sm:Dot1x Initialize State Entered
    00:19:07:     dot1x_bend Fa0/17: idle during state dot1x_bend_initialize
    00:19:07: @@@ dot1x_bend Fa0/17: dot1x_bend_initialize -> dot1x_bend_idle
    00:19:07: dot1x-sm:Dot1x Idle State Entered
    00:19:07:     dot1x_auth Fa0/17: during state auth_aborting, got event 16(noauth
    Abort_noeapLogoff)
    00:19:07: @@@ dot1x_auth Fa0/17: auth_aborting -> auth_connecting
    00:19:07: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_connecting_enter called
    00:19:07: dot1x-ev:dot1x_post_message_to_auth_sm: Tx for req_id for supplicant 0
    024.1d10.d7c5
    00:19:07: dot1x-ev:Transmitting an EAPOL frame on FastEthernet0/17
    00:19:07: dot1x-packet:Tx EAP-Request(Id), id 2, ver 1, len 5 (Fa0/17)
    00:19:07: dot1x-registry:registry:dot1x_ether_macaddr called
    00:19:07: dot1x-packet:Tx sa=000f.24e9.72d1, da=0180.c200.0003, et 888E (Fa0/17)
    00:19:07: dot1x-ev:Received an EAPOL frame on interface FastEthernet0/17
    00:19:07: dot1x-packet:Rx EAP-Response(Id), id 2, ver 1, len 21 (Fa0/17)
    00:19:07: dot1x-packet:Rx sa=0024.1d10.d7c5, da=0180.c200.0003, et 888E (Fa0/17)
    00:19:07: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:19:07: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:19:07: dot1x-ev:RECEIVED mac =0024.1d10.d7c5 and Stored MAC =0024.1d10.d7c5
    00:19:07:     dot1x_auth Fa0/17: during state auth_connecting, got event 7(rxRes
    pId)
    00:19:07: @@@ dot1x_auth Fa0/17: auth_connecting -> auth_authenticating
    00:19:07: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_connecting_exit alled
    00:19:07: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_authenticating_enter called
    00:19:07: dot1x-ev:sending AUTH_START to BEND for supp_info=80D7E584
    00:19:07: dot1x-sm:Fa0/17:0024.1d10.d7c5:auth_connecting_authenticating_action c
    alled
    00:19:07: dot1x-ev:Received AuthStart from Authenticator for supp_info=80D7E584
    00:19:07:     dot1x_bend Fa0/17: during state dot1x_bend_idle, got event 1(auth_
    start)
    00:19:07: @@@ dot1x_bend Fa0/17: dot1x_bend_idle -> dot1x_bend_response
    00:19:07: dot1x-sm:Dot1x Response State Entered for supp_info=80D7E584 hwidb=807
    D353C, swidb=807D4898 on intf=Fa0/17
    00:19:07: dot1x-ev:Managed Timer in sub-block attached as leaf to master
    00:19:07: dot1x-sm:Started the ServerTimeout Timer
    00:19:07: dot1x-ev:Going to Send Request to AAA Client on RP for id = 2 and leng
    th = 21
    00:19:07: dot1x-ev:Got a Request from SP to send it to Radius with id 4294967285
    00:19:07: dot1x-ev:Couldn't Find a process thats already handling the request fo
    r this id 2
    00:19:07: dot1x-ev:Inserted AAA request for interface FastEthernet0/17, MAC 0024
    .1d10.d7c5, VLAN 0 on pending request queue
    00:19:07: dot1x-ev:Found a free slot at slot 0
    00:19:07: dot1x-ev:Found a free slot at slot 0
    00:19:07: dot1x-ev:Processing AAA request for interface FastEthernet0/17, MAC 00
    24.1d10.d7c5, VLAN 0 from pending request queue
    00:19:07: dot1x-ev:Request id = -11 and length = 21
    00:19:07: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:19:07: dot1x-ev:The Interface on which we got this AAA Request is FastEtherne
    t0/17
    00:19:07: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:19:07: dot1x-ev:Username is DUZEY\SAYTAMANER
    00:19:07: dot1x-ev:MAC Address is 0024.1d10.d7c5
    00:19:07: dot1x-ev:RemAddr is 00-24-1D-10-D7-C5/00-0F-24-E9-72-D1
    00:19:07: dot1x-ev:Found a supplicant block for mac 0024.1d10.d7c5 80D7E584
    00:19:19: dot1x-registry:dot1x_port_linkchange invoked on interface FastEthernet
    0/17
    00:19:19: dot1x-ev:supp_info=80D7E584 txWhen_timer=80D7E5D4 quietWhile_timer=80D
    7E594reAuthWhen_timer=80D7E5B4 awhile_timer=80D7E5F4
    00:19:19: dot1x-ev:destroy supplicant block for 0024.1d10.d7c5
    00:19:19: dot1x-ev:supp_info=80D71C74 txWhen_timer=80D71CC4 quietWhile_timer=80D
    71C84reAuthWhen_timer=80D71CA4 awhile_timer=80D71CE4
    00:19:19: dot1x-ev:destroy supplicant block for 0000.0000.0000
    00:19:19: dot1x-ev:Enter function dot1x_aaa_acct_end
    00:19:19: dot1x-ev:Found a supplicant block for mac 0000.0000.0000 80D71C74
    00:19:19: dot1x-ev:Found a supplicant block for mac 0000.0000.0000 80D71C74
    00:19:19: dot1x-ev:dot1x_port_cleanup_author: cleanup author on interface FastEt
    hernet0/17
    00:19:19: dot1x-ev:dot1x_post_message_to_auth_sm: cleanup author from interface
    This is driving me crazy, working on it for a whole week and no results..
    Thank you..

    Hi again,
    I have put the config on 2960. Now as soon as the authentication starts, this is the message on debug;
    dot1x authentication unable to start - authenticator not enabled..
    Any ideas?
    regards,
    onur

  • Cisco 2950 - 24 WS switch express install issue

    Hi Guys,
    Got a Cisco 2950 24 port switch that I need to setup and I can't seem to get the page for Express install
    In firefox when trying to connect to 10.0.0.1 I get the message "connection was reset" in internet explorer "page cannot be displayed"
    when doing a arp -a I can see that the switch does get the IP address 10.0.0.1 and I can also ping the switch ok.
    Have followed the instructions and reset the switch and all the mode lights are green etc.
    my ethernet adapter does get the address 10.0.0.2 given from the switch (however connectivity is limited / not sure if this is supposed to be like this or not)
    have tried earlier versions of firefox (even 1x 2x 3x 4x) etc and also older versions of IE incase there is something weird going on there. have also tried using a mac and trying safari which gives similar results.
    So i think the http server is enabled on the switch, as it should be by default when it is reset etc. according to cisco's documentation.
    I know using the console cable would be alot easier however I don't have one available and not easy for me to get
    any ideas? has anyone ever successfully been able to use this express install  web page on a cisco 2950 before? It has Version 12.1(22)EA14 so express install should work on this switch!
    cheers,

    managed to get hold of a console cable. checked switch and http-server command was enabled so have no idea why this feature was not working...
    did some research and someone suggested that it is fussy with the version of java you are running on the pc ( requires old version of java?) .. possibly that may have an influence who knows?
    Think ill just carry around a Console cable in future!

  • Apple wired Dot1X - on Cisco 2950 switches

    Hi, I have an issue with Apple desktop computers running 10.7 and 10.8 MacOS.
    The problem is that we have only 2950 switches and we are very limited with what we can do on them, so we wanted basic DOT1X user authentication and VLAN placement. Those two are working great, except when user logs off, Mac stops sending DOT1X and port becomes unauthenticated. We alleviated that issue by using guest-vlan for failed dot1x authentications, but now we have a problem that once user logs in, there is no session change on 2950 and it doesn’t even try to authenticate user until we bounce the port.
    Is there any way to fix this, on Cisco switch or Mac computer? One of the things that crossed my mind is bouncing port on Mac PC using some kind of logon script?
    Has anyone else had this issue and was able to solve it?
    Thanks.

    Hello Align,
    Cisco 2950 switch with 12.1(9) supports 802.1 x authentications. As you are saying that you already configured 802.1x authentication and its working fine. I think there is problem with your MAC OS configuration. Please follow the below link to configure 802.1x on Apple.
    http://support.apple.com/kb/ht3326

  • Weird Display on 2950 Switch

     When I connect with my Cisco 2950 Switch, I can see the weird kind of language as per my attachment.
     Switch is working good with Cisco IP phones connected with it.
     Can anyone help ?

    Check your terminal settings... default is 9600 8n1... You might have changed the speed from either your terminal program or your serial connection.
    Tim...

  • Apple Banned me, because of a very weird problem with my "Factory Unlocked"

    Hi Everybody! Im having a very weird problem with my unlocked iphone 4.
    First of all, i would like to apologize because of my english, is not very good. My native language is Spanish.
    Well.. Im from Mexico, and here we can buy the iphone Unlocked on the Apple Online Store.
    Here's my problem. Apple has exchanged my iphone 3 times.
    I returned the iphone the first time because the screen was totally yellowish, other than that everything was working great!, that was by the end of September.
    On October 20th, i recieved my second iphone, and then a bigger problem started .
    Before i continue, let me give you this information: here in Mexico we have basically 3 cell phone companies
    1.- Telcel
    2.- Movistar
    3.- Unefon
    OK, now on october 20th, i recieved my second iphone, and then procced to activate via itunes using my UNEFON sim card (microsim).
    And every time i tried to activate it, only got this message onscreen:
    http://i148.photobucket.com/albums/s2/jorgelomeli/Screenshot2010-10-29at24915PM. png
    I though something was wrong with my brand new factory unlocked iphone 4.
    I have 4 more simcards from my brothers (they all had iphone 4 too)
    I tried telcel sim card, and i could activate my iphone. Then i insterted the Movistar microsim, and it worked too!! But then when i put the Unefon sim, the itunes logo inmediatly appears on the screen asking to activate on itunes, and when i tried that, the only response i got was the image above saying " The Simcard inserted on this iphone does not appear to be supported"
    Weird thing here is, that, when i put my Unefon sim card on my brothers iphone 4, it worked great! on all of them, internet 3g, phone, wireless , evrything!
    I called apple support, and they exchange the iphone for another one.
    I recieved the third iphone on October 29. Last friday. and guess what? SAME PROBLEM! different serial number, same week production (week 42) but exactly the same message on itunes.
    Very, very frustrated, i called apple again, and after 1 hour with thechnical support, they told me " We are sorry, but we can only offer you, your money back, NO MORE EXCHANGES FOR YOU"
    I said why?... i dont want my money back! i want an UNLOCKED iphone!, but they refuse to give me another iphone.
    When i asked techincal support, why my unefon sim card worked great on all three of my brothers iphone but not on mine, he just told me, "I really dont know, i guess they just got lucky" ****, this answer put all my trust i had on apple products for years, right on the garbage.
    Since they refused to give me another iphone, i accepted my money back, and inmediatly after i finished the call, i asked my brother to buy me one more time an iphone 4 using his name, and his credit card. Now i have to wait until November 8-12 to recieve my new iphone, hoping this time i get a REAL UNLOCKED iphone, and not a partially unlocked iphone.
    btw. i even went to Unefon costumer service and bought a new prepiad line, with a new microsim, just to be 100% sure that this problem is not because of the sim. And again didnt worked on my iphone, but it worked on any of my brothers iphone4.
    Serial numbers of the 3 iphones:
    79039C0U* (this one worked great with Unefon, only problem was yellow screen)
    85042GR4*
    81042FJB*
    What do you suggest me? any info would be really aprecciated
    FYI i also restore 4 times the last iphone and nothing seemed to work, i use 3 different computers, Macbook Pro, iMac, and an Hp with Windows 7, and the same message on all three computers.
    Wierd thing also, one of my brothers bougth an iphone 4 this last week too, but he bought the 16Gb not the 32Gb. His iphone production week is 42 also! and when i put my Unefon sim in his iphone works great!
    I dont know what else i can do, I just need to have faith that my new iphone coming this november will be real unlocked, but what if i'll recieve an iphone and then the same problem?? time for android? just kidding really guys, what can i do? anyone with similar problem like me? i dont wanna use Telcel or Movistar, i wanna use Unefon, and thats why i bought an Unlocked iphone
    btw: jailbreak is not a solution for me, because i always like to use legal software on all my apple products, and because of the warranty.

    According to http://support.apple.com/kb/HT1937, there are two official carriers in Mexico (Movistar and Telcel) and neither carrier offers an unlocked phone.

  • Iphone 4, having a weird problem /: can't seem to fix it!

    So i have been having my iphone for a while, i have no warranty on the phone now. I have this weird problem that when i scoll down my messages and stuff i can see the outline of the message kind of show rainbowish colors that sort of show a bit when i scroll, right near the border of the message. its kind of annoying at times, also there are times when i press the home button, right when i get to my wallpaper, the outline of the letters when i text are there like very very faint, they disappear after for a while but then come back sort of like a glitch, and i cant fix it at all. then i would see faint horizontal lines, i would notice them when i use the camera, they disappear also. can anyone help me with this or suggest something?

    Screen lag is normaly the LCD itself. But try restoring the iPhone. http://support.apple.com/kb/HT1414

  • Hiya, I've got a weird problem with my iPhone4. On the 'home page' of my iPhone the mail symbol tells me there's a new mail waiting for me. However, there's no new mail to be found. Does anyone know what the problem is? Thanks

    Hiya, I've got a weird problem with my iPhone4. On the 'home page' of my iPhone the mail symbol tells me there's a new mail waiting for me. However, there's no new mail to be found. Does anyone know what the problem is? Thanks

    This response is a little late as I just read about your problem. I have a 2012 Dodge Charger and a 2012 Chrysler Town and Country and both worked flawlessly with the iPhone 5s my wife and I had. However, we just upgraded to the iPhone 6 and Uconnect will receive calls but you cannot answer them. You can callout successfully, however. the annoyance being the inability to answer incoming calls in the HandsFree mode.

  • SAP GUI 7.10p15 weird problem on FB70

    Hi all,
    We upgraded SAP GUI 7.10 to patch level 15 from patch level 14 using the install server on our Windows XP machines. A weird problem seems to appear since then on FB70. You press once or twice the ENTER key, without filling any field on the screen and the GUI stays on a busy state forever (trying to constantly redraw the screen as to show an error message on missing account number). It results to 100% CPU usage on the client (Windows XP machines, tried on Windows 7 also with same result) and seems to also stress the SAP system a bit. The only way to stop that behavior is to use the Windows task manager and kill the busy window. I have not seen this behavior before and can't reproduce it in any other transaction until now.
    I got access on a machine that was still on patch level 14 and works just fine. I did the upgrade and the same behaviour (busy, 100% CPU) instantly appears. Oddly enough, this behavior does not occur if I run FB70 throught the debugger (/h) in any case.
    Have you seen something like this or do you have any clue why that weird behavior might appear?
    Thank you very much in advance for any insight

    Hello Artemios,
    Yes, this seems to be a know issue with Patch 15. Please open a ticket on BC-FES-GUI to get a fix for that or wait until Patch 16 is released.
    Kind regards,
    Martin

  • Weird problem involving my external hard drive - help please!

    I recently got a formac mini 120 gb firewire hard drive, which had been working fine with my g4 quicksliver.
    i then went to a friends (g5 machine) with my drive and he put some data on it - bought it back to mine and managed to re connect the drive and take the data - no problem - very happy.
    I recently gave my drive to another friend using a g5 and when it came back, nothing - i don't get the drive symbol appearing. turned the comp on and off many times and tried re-connecting etc still no drive appearing.
    Then i took the drive to my friend with a mac lap top power book. connected there - working fine. Baffling. was happy that my data can still be accessed.
    I know it's not the firewire cable because i can get power to the drive - i can see the red light at the fron on.
    Can anyone help with this weird problem?
    Thanks

    Thought you could use this info about getting FireWire to work!
    First, you should always Repair Permissions in Disk Utility before and after any update; I would do that now. If you installed your update with FireWire plugged in, your Mac may not recognize it anymore.
    Try resetting your FireWire ports by disconnecting all FW devices, shut down your Mac and unplug it from AC power (wall socket) for 30 minutes. plug it back in and try FW.
    If that did'nt work, download the combo update from this site (yours may be corrupt), not Software Update, disconnect all firewire + USB devices except keyboard + mouse, Repair Permissions, re-install update, Repair Permissions again + try. Yours might be the 10.4.10 Combo update. I have no idea since you did not fill out your specs. fully when you signed in to this site. Others reading, download the Combo that applies to your system. This link is for PPC Macs not Intel Macs.
    If that still did'nt get it Zap the PRAM. While restarting Mac hold down the following key combo Command-Option-P-R. Keep holding those keys down till you hear the second start-up chime, then release.
    For those of you with Macs that are not PowerBooks or iBooks, a bad internal battery can cause FireWire to not be recognized, so make sure it's good! Also, here is Apple doc.#88338 on getting FireWire to work.
    Good Luck!
    Cheers!
    DALE

  • Weird problem when executing an update statement

    Please help me out with this issue. This a very weird problem i'm facing while executing the following update statement.
    update tblo.S_TABLE c
    SET (ACCNT_NAME, ACCNT_LOC)
    =
    (select NAME, LOC from S_TABLE1 p
    where p.ROW_ID = c.ACCNT_ID)
    where ROW_ID = 'XXXXX'
    The statement executes perfectly fine in "SQL Plus" but when i try from my application or any SQL Tool that uses ODBC, it fails with the following error
    <eb1>ORA-00923: FROM keyword not found where expected
    State:S1000,Native:923,Origin:[Oracle][ODBC][Ora]</eb1>
    ODBC Driver Used: 9.2.0.2.0

    Yes this could most probably be resolved by upgrading the driver. I'hv tried MS Oracle ODBC driver but that is even more problematic!
    The applications works fine in another environment which uses a Merant ODBC driver. Thanks for your time and advice.

  • Weird problem when downloading the output to an excel sheet

    Hi to all,
          when i download the list, output by an alv grid, i observe a weird problem..in the excel sheet the last digit (10th digit) of the first col. which is delivery no., is getting truncated...0001802563 is getting downloaded as 000180256..couldn't understand why...when i use conversion_exit fm, the values are not getting truncated and downloading correctly...curious to know what's gone wrong in this funcationality? thanks all
    cheers,
    Shankar. M.

    actually the problem is in the field catalog.if u can send me the code, i shall bug fix it for u.

  • Weird problem with JApplet

    I'm having a weird problem with JApplet. So first I create an Applet with this code
    public class japp extends JApplet {
         public void init() {
              Container content=getContentPane();
              JButton jb=new JButton("Hello");
              content.add(jb);
    }and with this in the .html file;
    <html>
    <body>
    <APPLET CODE="japp.class" WIDTH="650" HEIGHT="500"></APPLET>
    </body>
    </html>
    And opened it in Firefox, it worked as expected. However, when I change the code in any way, i.e.
    public class japp extends JApplet {
         public void init() {
              Container content=getContentPane();
              JButton jb=new JButton("Goodbye");
              content.add(jb);
    }and compile it, it still shows the old button that displays "Hello". I've tried deleting the .class file from before and recompiling, that doesn't work. What am I doing wrong?
    Thanks.

    Reloading the page usually doesn't work. You will need to open the Java Console and clear classloader cache (x). You can also use appletviewer for testing purposes.

  • Problem of PI am having a weird problem in prinrinting List in Address Book

    I am having a weird problem in printing a list of addresses in Address Book. The odd number pages (1,3,5,etc.) print fine but the even number pages move the phone numbers from the third column and prints them over the second column's address and Note fields. Anybody know what is going on here? I have tried the Roll Call Directory software suggested by one respondent on another printing problem and while it is very nice, it seems to have its own quirks (Splits the information when it reaches the bottom left column of a two column set-up or prints at the top left column of the next page when it reaches the end of the right column instead of keeping the address intact in one spot).

    P.S. To as to this problem. I tried printing some more pages of the address list and now while some of the odd numbered pages seem OK as you go along it switches to some of the even numbered pages being OK with the odd numbered pages having the third column shifting to overprint on part of the 2nd column. In addition, I can't print envelopes since the program simply does nothing or crashes when the print button is selected.

Maybe you are looking for