Weird red lines on the NTSC display

After I upgraded to Final Cut Studio, my Final Cut Pro started to show these weird red lines over the image on the NTSC display. It happens very often too, like every other time I pause the timeline. They are bright red lines over the video, and the patterns vary. Anyone know what this is and how to fix it? it's very disturbing.
I've also noticed that the image on the NTSC display doesn't update when I move the cursor around with the mouse, or in my case - the tablet pen. In other words, the image on the NTSC display stays the same until I play and pause again. This also happens way too often. Anyone else having this problem?
Powermac G5 2GHz DP Mac OS X (10.4.4) Final Cut 5.0.3, Compressor 2.0.1, DVD SP 4, QT 7.0.3

When the going gets weird, the weird trash their preferences, repair permissions and run Disk Warrior on their drives.
rh

Similar Messages

Ios8.....hate!'After upgrading my iPad will do nothing except refuse to take a charge display a black screen or a battery red line or the occasional apple logo. Have tried soft boot and hard boot and nothing!,!

After upgrading my iPad will do nothing except refuse to take a charge display a black screen or a battery red line or the occasional apple logo. Have tried soft boot and hard boot and nothing!,!

Hello there, Victoria.
Great job on troubleshooting on your own. The following Knowledge Base article offers up some great steps to review and additional recomendations:
iPhone and iPod touch: Charging the battery
http://support.apple.com/kb/HT1476
Resolving issues
If your battery doesn't charge, or if your device shows a low-battery image, black screen, or "accessory not supported" alert, follow these steps.
Inspect the connector at the bottom of the phone:
Make sure that there are no bent pins in the connector.
Make sure that the connector is free from debris.
If there are bent pins or debris, please contact Apple Support.
Otherwise, continue troubleshooting.
Make sure that the outlet you're using works.
Make sure that the Apple USB cable and Apple USB power adapter work.
Plug the device in to power and let it charge until your device turns on. This could take between 10 and 30 minutes. If you don't have an Apple USB power adapter, try connecting to a computer's high-power USB 2.0 port (not a keyboard). The computer must be on.
If the device still exhibits an issue, try turning your device off and then on again while connected to power.
If the issue persists, please contact Apple Support.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

When opened, my image appears black with a few red lines at the top, yet the thumbnail looks as it should be. How do I fix this?

I have been working on an illustration in Photoshop for a few months now. When I tried to open it yesterday it came up as a single layered black image with a few red lines at the top. I have no idea what this is. I have not even used red in my artwork. However, no matter how many times open this file, the thumbnail still looks like my artwork, as it should be. How do I fix this? Will I be able to get my artwork back? Please help! Thank you in advance.

Make sure you has the latest Windows Device driver for your display adapted from its manufacturer's web site installed on your system. Perhaps you updated the device driver with a Microsoft Windows Update. Microsoft update does not always install the correct update needed fpr Phoroshop.
Supply pertinent information for quicker answers
The more information you supply about your situation, the better equipped other community members will be to answer. Consider including the following in your question:
Adobe product and version number
Operating system and version number
The full text of any error message(s)
What you were doing when the problem occurred
Screenshots of the problem
Computer hardware, such as CPU; GPU; amount of RAM; etc.

Program Logic for showin number of red lines on the o/p screen?

Hi
I have an output list wherein I am settin clours on the output screen based on certain conditions like if say 2 values in my final internal table doesn't match then I am settin the colour to red also green is set.
My requirement is that I want to show the total number of red lines on the o/p screen .
How can I do that?
Thanks

what type of report ? is it ALV or Normal report ?
if it is normal report ,then use one variable ,when ever you have red color condition ,use this variable
data : v_data type i.
if redcondition.
v_data = v_data + 1.
endif.
display v_data ( This is total number lines )
Thanks
Seshu

Red line above the time line

How do I get it so after initially importing my video the line above the time line will be green instead of red. It stays red until after I render the whole clip. I am importing my video clips from my camcorder. How do you determine the correct project settings if that is the issue?
Thanks

freedog69
How do I get it so after initially importing my video the line above the
time line will be green instead of red.
Not possible as worded. If you have the correct project preset, there will
be no colored line over this Timeline content.
If you do not have the correct project preset, there will be a red line
over this Timeline content.
What version of Premiere Elements are you using and on what computer
operating system is it running? APE 8 Windows XP 3GB of ram Pentium Dual core
Proc 2.41 Ghz
If you are talking "red" line, then you must be working with a version of
Premiere Elements earlier than 11. Assuming that....
If your project preset matches the properties of your source media, then,
when you bring one of those files to the Timeline, you will get no colored
line over the Timeline. But, after that, after you edit that content, a red
line will appear. That is when you render the Timeline content to turn the
line green.Thereafter, that original content will never revert to the no
colored line status as you work through editing that project. It will just go
through the red green color indicator system.
No colored line and green = the program telling you that you now have the
best possible preview of the Timeline content when viewing it in the Edit
Mode monitor playback. Red line = the program telling you that you do not
have the best possible preview of the Timeline content and, if you want that,
then you can press the Enter key of the computer main keyboard to make that
happen.
What are the properites of your source media... Canon HF 10 camera and
Panasonic HV-720
video and audio compression
frame size
frame size
interlaced or progressive
file extension
pixel aspect ratio
General Panasonic HV-720
ID                                : 1 (0x1)
Complete name                     : K:\Busters_Tap\New
Matches-CamB\f0069412.m2ts
Format                            : BDAV
Format/Info                       : Blu-ray Video
File size                         : 2.00 GiB
Duration                          : 58mn 59s
Overall bit rate                  : 4 854 Kbps
Maximum Overall bit rate         : 18.0 Mbps
Video
ID                                : 4113 (0x1011)
Menu ID                           : 1 (0x1)
Format                            : AVC
Format/Info                       : Advanced Video Codec
Format profile                    : [email protected] (mailto:[email protected])
Format settings, CABAC           : Yes
Format settings, ReFrames        : 2 frames
Format settings, GOP             : M=1, N=30
Codec ID                          : 27
Duration                          : 58mn 59s
Bit rate mode                     : Variable
Bit rate                          : 4 267 Kbps
Maximum bit rate                  : 16.8 Mbps
Width                             : 1 920 pixels
Height                            : 1 080 pixels
Display aspect ratio             : 16:9
Frame rate                        : 29.970 fps
Color space                       : YUV
Chroma subsampling                : 4:2:0
Bit depth                         : 8 bits
Scan type                         : Interlaced
Scan order                        : Top Field First
Bits/(Pixel*Frame)                : 0.069
Stream size                       : 1.76 GiB (88%)
Audio
ID                                : 4352 (0x1100)
Menu ID                           : 1 (0x1)
Format                            : AC-3
Format/Info                       : Audio Coding 3
Mode extension                    : CM (complete main)
Codec ID                          : 129
Duration                          : 58mn 59s
Bit rate mode                     : Constant
Bit rate                          : 384 Kbps
Channel(s)                        : 2 channels
Channel positions                 : Front: L R
Sampling rate                     : 48.0 KHz
Bit depth                         : 16 bits
Compression mode                  : Lossy
Delay relative to video          : -558ms
Stream size                       : 162 MiB (8%)
Text
ID                                : 4608 (0x1200)
Menu ID                           : 1 (0x1)
Format                            : PGS
Codec ID                          : 144
Duration                          : 58mn 58s
Delay relative to video          : 34ms
General- Canon HF 10
ID                                : 0 (0x0)
Complete name                     : K:\Busters_Tap\New Matches
CAM-A\00001.MTS
Format                            : BDAV
Format/Info                       : Blu-ray Video
File size                         : 1.90 GiB
Duration                          : 49mn 5s
Overall bit rate                  : 5 551 Kbps
Maximum Overall bit rate         : 13.7 Mbps
Video
ID                                : 4113 (0x1011)
Menu ID                           : 1 (0x1)
Format                            : AVC
Format/Info                       : Advanced Video Codec
Format profile                    : [email protected] (mailto:[email protected])
Format settings, CABAC           : Yes
Format settings, ReFrames        : 2 frames
Codec ID                          : 27
Duration                          : 49mn 5s
Bit rate mode                     : Variable
Bit rate                          : 5 066 Kbps
Maximum bit rate                  : 12.0 Mbps
Width                             : 1 440 pixels
Height                            : 1 080 pixels
Display aspect ratio             : 16:9
Frame rate                        : 29.970 fps
Color space                       : YUV
Chroma subsampling                : 4:2:0
Bit depth                         : 8 bits
Scan type                         : Interlaced
Scan order                        : Top Field First
Bits/(Pixel*Frame)                : 0.109
Stream size                       : 1.74 GiB (91%)
Audio
ID                                : 4352 (0x1100)
Menu ID                           : 1 (0x1)
Format                            : AC-3
Format/Info                       : Audio Coding 3
Mode extension                    : CM (complete main)
Codec ID                          : 129
Duration                          : 49mn 5s
Bit rate mode                     : Constant
Bit rate                          : 256 Kbps
Channel(s)                        : 2 channels
Channel positions                 : Front: L R
Sampling rate                     : 48.0 KHz
Bit depth                         : 16 bits
Compression mode                  : Lossy
Delay relative to video          : -66ms
Stream size                       : 89.9 MiB (5%)
What brand/model/settings camera provided you will the source media for the
Premiere Elements 10 project. Canon HF 10 and Panasonic HV-720
In a message dated 1/9/2014 5:00:15 P.M. Eastern Standard Time,
[email protected] writes:
Re: Red line above the time line
created by A.T. Romano (http://forums.adobe.com/people/A.T.+Romano) in
Premiere Elements - View the full discussion
(http://forums.adobe.com/message/5998225#5998225)

Weird red line through arrows vs pointer when I try to use my mouse to grab stuff per usual

Anyone know why my screen is locked & not allowing me to move or place anything? & the cursor has a weird red line through arrows pointing in opposite directions when I try to grab anything. Uhmph

You have selected the Slip Tool.
If its not over a clip it gets the red line.
Select the Selection Tool (V) for placing moving around etc. of clips.

My Blackberry does not start up, all I get is a red line through the battery

Hi this is my first Blackberry and seven months after purchace I phone stops working. All I get when I turn it on is a red line through the battery. I bought a new battery and the same thing. I am like at wits end, HELP!

#1. Be patient with #2.
#2. Leave the device to charge 2-3 hours, and then, still connected to the USB cable, remove the the battery from the device a few seconds and reinsert it. If it boots--leave it to charge to 100% (check Options > Status for the percentage).
Message Edited by JSanders on 08-02-2009 11:18 PM
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Red Line in the timeline by the time code

Hello Again,
Suddenly, a red line appeared in the timeline by the time code? what does it mean? How can I delete it? Thanks again.

Thank you for your feedback.
Yes, I' familiar about the un rendered red lines. The line I'm talking about is right inside the "ruler" as if the digits (minutes/seconds) are crossed out. This line also showing up at the canvass window. I think this came out when i'm doing some keyframing.
Thanks again.

I have marked some video cuts for removing, and want to activate them again and take away the marking (a red line over the thumbnails). How do I do that?

I have marked some video cuts for removing, and want to activate them again and take away the marking (a red line over the thumbnails). How do I do that?

In the middle tool bar, near the Reject Tool that you used to make the red marks, there should be an "Un-Mark" Tool. Select this tool and you can erase the red marks. It should look like an empty star.
YOu can select "View Rejected Only" to make sure you get them all.

Red lines & plaid on cinema display when watching DVDs

I bought a MacBook Pro & cinema display in November. The computer's working perfectly but when I watch DVDs on the cinema display, red lines will occasionally flicker horizontally across the screen while the DVD otherwise continues to play normally. After about 10 seconds of this, the screen stops showing the red-lined DVD footage and shows a plaid patchwork instead. Moving the mouse causes a white vertical line to move through the plaid. Turning off the cinema display and letting it rest for a few seconds returns it to functioning normally. The sound works normally throughout. The plaid is primarily lavender and white in color, neither of which colors are prominent either in the DVD imagery or my desktop.
This only happens when I'm using DVD Player, either in fullscreen or windowed mode, and only on the cinema display, not the MacBook Pro's display. I've used the cinema display for 12+ hours at a time with Final Cut Pro (under 10.5.1), Maya (under Bootcamp, with XP), and Rhino (under Parallels), and have never once had this problem. But if I spend more than an hour watching a DVD, I'll experience it at least once.
I've read about electro-static discharge, but that shouldn't be the cause because I've only connected the display to the computer twice, and both times I followed the connection instructions very carefully. I can't find any mention of this problem on this site, but I wanted to ask if anyone had any ideas before I drag the thing and my CD full of photos into an Apple store for them to look at. I'd be thrilled if anyone can give me miraculous solutions, but I'd also appreciate it if you could even confirm that this is probably just a weird hardware problem that replacing the display would fix and that the fact that it only occurs when I'm using DVD Player is irrelevant.
Thanks.

I also have a 30" ACD and I'm experiencing exactly the same problems as you describe, but not only in DVD Player, but as long as the background is black it's possible to see the red lines here and there on the screen. Very, very annoying and it doesn't give me a professional impression of the monitor I so deeply love.
Is this a hardware problem that can be fixed, or should I ask for a new monitor?
- Chris

A vertical red line on the screen

Sir, my product name is HP Pavilion g6 Notebook pc and having 64 bit operating system. Sir, a vertical red line has appeared on the screen and it is seen when i start my laptop.A few days ago it was dissapeared but next day it again appears.Please help me to remove it.

Hello irohitgupta,
Thank you for posting on the HP Forums!
I understand your computer display is experiencing issues with a red line. I will do my best to assist you! To troubleshoot the issue, please refer to the relevant sections of this HP document: Display Quality Issues
The sections I would like you to refer to are "several colored vertical lines in the display", "screen is discolored" and "general troubleshooting tips for display quality issues". Please try all of the troubleshooting and let me know the results.
If the issue persists, please provide the following information:
1. The computer's model number. If you require assistance locating this information, please reference this website: Guide to finding your notebook product number
2. The computer's operating system. If you require assistance locating this information, please reference this website to determine your Windows operating system.
3. Does this occur on certain programs, or all programs?
4. Have you installed any new software or drivers on this computer, before the issue appeared?
Additionally, if the issue just began occurring, I would perform a system restore. I want you to bring the computer back to the earliest restore point possible, in an attempt to dodge whatever caused the issue. Here is a document on how to perform a System Restore: System Restore
Mario
I worked on behalf of HP.

I am getting a weird green line at the bottom of my screen...

I am trying to burn a DVD in iDVD.
I keep getting a green line at the bottom of the screen. I tried "squaring" the pixels before outputting the project, but I didn't render the project this way in FCP before trying that.
Could that be the problem?
I also tried buring at 1x.
Any help would help!
Thank you,
Evan Jacobs

Well to answer the questions. This artifact is in fact a physical one because you can see it when you boot the Mac and sign in with a different profile. I decided to test my luck at the local Apple Store just to see what they said. They looked at the display for about 3 minutes and then said that it would be nearly 700 bucks for parts and labor to basically put a new display on my laptop. He said that since its a TFT screen chances are on of the layers within the screen are messed up hence I see this black line. I decided Im going to look elsewhere and see if I can't find a solution here. If worse comes to worse, then I'll live with it till the Pro Book is out and get that with Apple care.

How can I follow the red line in the timeline?

Bit of a basic question, but when i play through a song i want it to follow with the red line, but it keeps going off the screen and it never follows it
how do i put it back on?

thanks

The red line on the middle of screen

My dad got a macbook pro couple months ago at an Apple Store in Orlando FL, last month he went back to Netherland and two days ago he saw a red line on his screen.He said that red line still on the middle of screen and He is sick of that.My question is he got his receipt and the other kind of stuff with him..Can he get a new macbook pro or take his macbook pro be repaired at an Apple Store in Netherland? He has one year warranty.
Thanks
MacBook Pro 15' Mac OS X (10.4.9)

Warranty is worldwide. He can take it to a Dutch Apple Store without worrying
Best of luck.

Red Lines Across the screen?!

I did a search but didn't find anything similar to what I'm experiencing. I watch DVDs and movies on my iBook and noticed lately that the screen will have a reddish hue. I can adjust the screen and it will go away, but I've noticed it's happening more and more, and also getting harder to adjust the screen where the red lines are not showing up. I'm trying to figure out if it is a connection cable or the LCD. I can still get a clear picture with the LCD, but if I move it just a little, they come back.

You can follow the directions here:
http://www.keepandshare.com/doc/view.php?id=1132604&da=y
(You will need to download the PDF.)
Choose the links for the number of "Things to do first" from iFixit's website here:
http://www.ifixit.com/Guide/Device/iBookG312%22

Weird red lines on the NTSC display

Similar Messages

Maybe you are looking for